- 27 Apr, 2020 4 commits
-
-
Lyude Paul authored
While we support using both tx slots for sideband transmissions, it appears that DisplayPort devices in the field didn't end up doing a very good job of supporting it. From section 5.2.1 of the DP 2.0 specification: There are MST Sink/Branch devices in the field that do not handle interleaved message transactions. To facilitate message transaction handling by downstream devices, an MST Source device shall generate message transactions in an atomic manner (i.e., the MST Source device shall not concurrently interleave multiple message transactions). Therefore, an MST Source device shall clear the Message_Sequence_No value in the Sideband_MSG_Header to 0. This might come as a bit of a surprise since the vast majority of hubs will support using both tx slots even if they don't support interleaved message transactions, and we've also been using both tx slots since MST was introduced into the kernel. However, there is one device we've had trouble getting working consistently with MST for so long that we actually assumed it was just broken: the infamous Dell P2415Qb. Previously this monitor would appear to work sometimes, but in most situations would end up timing out LINK_ADDRESS messages almost at random until you power cycled the whole display. After reading section 5.2.1 in the DP 2.0 spec, some closer investigation into this infamous display revealed it was only ever timing out on sideband messages in the second TX slot. Sure enough, avoiding the second TX slot has suddenly made this monitor function perfectly for the first time in five years. And since they explicitly mention this in the specification, I doubt this is the only monitor out there with this issue. This might even explain explain the seemingly harmless garbage sideband responses we would occasionally see with MST hubs! So - rewrite our sideband TX handlers to only support one TX slot. In order to simplify our sideband handling now that we don't support transmitting to multiple MSTBs at once, we also move all state tracking for down replies from mstbs to the topology manager. Signed-off-by: Lyude Paul <lyude@redhat.com> Fixes: ad7f8a1f ("drm/helper: add Displayport multi-stream helper (v0.6)") Cc: Sean Paul <sean@poorly.run> Cc: "Lin, Wayne" <Wayne.Lin@amd.com> Cc: <stable@vger.kernel.org> # v3.17+ Reviewed-by: Sean Paul <sean@poorly.run> Link: https://patchwork.freedesktop.org/patch/msgid/20200424181308.770749-1-lyude@redhat.com
-
Zheng Bin authored
Fixes coccicheck warning: drivers/gpu/drm/rockchip/cdn-dp-reg.c:604:2-3: Unneeded semicolon drivers/gpu/drm/rockchip/cdn-dp-reg.c:622:2-3: Unneeded semicolon drivers/gpu/drm/rockchip/cdn-dp-reg.c:703:2-3: Unneeded semicolon Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zheng Bin <zhengbin13@huawei.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Link: https://patchwork.freedesktop.org/patch/msgid/20200424074410.1070-1-zhengbin13@huawei.com
-
Enric Balletbo i Serra authored
This fixes the following warning detected when running make with W=1 drivers/gpu/drm/rockchip//cdn-dp-core.c:1112:5: warning: no previous prototype for ‘cdn_dp_suspend’ [-Wmissing-prototypes] drivers/gpu/drm/rockchip//cdn-dp-core.c:1126:5: warning: no previous prototype for ‘cdn_dp_resume’ [-Wmissing-prototypes] Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Link: https://patchwork.freedesktop.org/patch/msgid/20200426161653.7710-1-enric.balletbo@collabora.com
-
Yannick Fertre authored
Number of endpoints could exceed the fix value MAX_ENDPOINTS(2). Instead of increase simply this value, the number of endpoint could be read from device tree. Load sequence has been a little rework to take care of several panel or bridge which can be connected/disconnected or enable/disable. Signed-off-by: Yannick Fertre <yannick.fertre@st.com> Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com> Link: https://patchwork.freedesktop.org/patch/msgid/1582877258-1112-1-git-send-email-yannick.fertre@st.com
-
- 25 Apr, 2020 14 commits
-
-
Bjorn Andersson authored
The InfoVision Optoelectronics M133NWF4 R0 panel is a 13.3" 1920x1080 eDP panel, add support for it in panel-simple. Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200420215728.1927434-2-bjorn.andersson@linaro.org
-
Bjorn Andersson authored
Define the vendor prefix for InfoVision Optoelectronics and add their M133NWF4 R0 13.3" FHD (1920x1080) TFT LCD panel to the compatible list of panel-simple. Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Acked-by: Rob Herring <robh@kernel.org> [vendor-prefix] Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200420215728.1927434-1-bjorn.andersson@linaro.org
-
Bjorn Andersson authored
The BOE NV133FHM-N61 panel is a 13.3" 1920x1080 eDP panel, add support for it in panel-simple. Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> [add boe_nv133fhm_n61_modes in alphabetical order] Link: https://patchwork.freedesktop.org/patch/msgid/20200420215742.1927498-2-bjorn.andersson@linaro.org
-
Bjorn Andersson authored
Add the BOE NV133FHM-N61 13.3" FHD (1920x1080) TFT LCD Panel to the compatible list of panel-simple. Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200420215742.1927498-1-bjorn.andersson@linaro.org
-
Souptick Joarder authored
These are dead code since 3.15. These can be removed forever if no plan to use it further. Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/1587407244-32574-1-git-send-email-jrdr.linux@gmail.com
-
YueHaibing authored
drivers/gpu/drm/panel/panel-truly-nt35597.c:493:31: warning: variable ‘config’ set but not used [-Wunused-but-set-variable] const struct nt35597_config *config; ^~~~~~ Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200417101401.19388-1-yuehaibing@huawei.com
-
Thierry Reding authored
Add missing compatible strings for the Panasonic and Chunghwa panels found on NVIDIA Dalmore and Cardhu boards. Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200417065328.1578603-1-thierry.reding@gmail.com
-
Enric Balletbo i Serra authored
Since commit 89958b7c ("drm/bridge: panel: Infer connector type from panel by default"), drm_panel_bridge_add() and their variants can return NULL and an error pointer. This is fine but none of the actual users of the API are checking for the NULL value. Instead of change all the users, seems reasonable to return an error pointer instead. So change the returned value for those functions when the connector type is unknown. Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200416210654.2468805-1-enric.balletbo@collabora.com
-
Enric Balletbo i Serra authored
The panel connector type should be set by the panel not the bridge, so remove the connector_type assignment. Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200416164404.2418426-2-enric.balletbo@collabora.com
-
Enric Balletbo i Serra authored
The LP120UP1 is a eDP panel, set the connector type accordingly. Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200416164404.2418426-1-enric.balletbo@collabora.com
-
Zheng Bin authored
Fixes coccicheck warning: drivers/gpu/drm/panel/panel-ilitek-ili9322.c:382:2-3: Unneeded semicolon drivers/gpu/drm/panel/panel-ilitek-ili9322.c:391:2-3: Unneeded semicolon Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zheng Bin <zhengbin13@huawei.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200424080224.30763-1-zhengbin13@huawei.com
-
Sebastian Reichel authored
Add timings for the AUO G121EAN01.4 panel. Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200415172725.84257-4-sebastian.reichel@collabora.com
-
Sebastian Reichel authored
Add timings for the AUO G156XTN01.0 panel. Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200415172725.84257-3-sebastian.reichel@collabora.com
-
Sebastian Reichel authored
Add timings for the G190EAN01 dual channel LVDS panel. Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200415172725.84257-2-sebastian.reichel@collabora.com
-
- 24 Apr, 2020 12 commits
-
-
Qiang Yu authored
Enable runtime pm by default so GPU suspend when idle for 200ms. This value can be changed by autosuspend_delay_ms in device's power sysfs dir. On Allwinner H3 lima_device_resume takes ~40us and lima_device_suspend takes ~20us. Tested-by: Bhushan Shah <bshah@kde.org> Reviewed-by: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Qiang Yu <yuq825@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200421133551.31481-11-yuq825@gmail.com
-
Qiang Yu authored
Add driver pm system and runtime hardware resume/suspend ops. Note this won't enable runtime pm of the device yet. v2: Do clock and power gating when suspend/resume. Tested-by: Bhushan Shah <bshah@kde.org> Reviewed-by: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Qiang Yu <yuq825@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200421133551.31481-10-yuq825@gmail.com
-
Qiang Yu authored
For being used by both device init/fini and suspend/resume. Tested-by: Bhushan Shah <bshah@kde.org> Reviewed-by: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Qiang Yu <yuq825@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200421133551.31481-9-yuq825@gmail.com
-
Qiang Yu authored
For called when PM do resume/suspend. Tested-by: Bhushan Shah <bshah@kde.org> Reviewed-by: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Qiang Yu <yuq825@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200421133551.31481-8-yuq825@gmail.com
-
Qiang Yu authored
Prepare resume/suspend PM. v2: Fix lima_pmu_wait_cmd timeout when mali400 case. Tested-by: Bhushan Shah <bshah@kde.org> Reviewed-by: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Qiang Yu <yuq825@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200421133551.31481-7-yuq825@gmail.com
-
Qiang Yu authored
Used for device resume/suspend in the following commits. Tested-by: Bhushan Shah <bshah@kde.org> Reviewed-by: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Qiang Yu <yuq825@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200421133551.31481-6-yuq825@gmail.com
-
Qiang Yu authored
We need to flush TLB anyway before every task start, and the page directory will be set to empty vm after suspend/resume, so always set it to the task vm even no ctx switch happens. Tested-by: Bhushan Shah <bshah@kde.org> Reviewed-by: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Qiang Yu <yuq825@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200421133551.31481-5-yuq825@gmail.com
-
Qiang Yu authored
No need to handle this check before calling lima_vm_put. Tested-by: Bhushan Shah <bshah@kde.org> Reviewed-by: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Qiang Yu <yuq825@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200421133551.31481-4-yuq825@gmail.com
-
Qiang Yu authored
When error task list is full, print the process info where the error task come from for debug usage. Tested-by: Bhushan Shah <bshah@kde.org> Reviewed-by: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Qiang Yu <yuq825@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200421133551.31481-3-yuq825@gmail.com
-
Qiang Yu authored
Simplify module init/exit with module_platform_driver. Tested-by: Bhushan Shah <bshah@kde.org> Reviewed-by: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Qiang Yu <yuq825@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200421133551.31481-2-yuq825@gmail.com
-
Robin Murphy authored
There's no point explicitly tracking the platform device when it can be trivially derived from the regular device pointer in the couple of places it's ever used. Signed-off-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Qiang Yu <yuq825@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/8d9073cc91c10fc70910587fd1794e0e8f32b467.1587509150.git.robin.murphy@arm.com
-
Robin Murphy authored
Use the optional form of platform_get_irq() for blocks that legitimately may not be present, to avoid getting an annoying barrage of spurious warnings for non-existent PPs on configurations like Mali-450 MP2. Signed-off-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Qiang Yu <yuq825@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/de475904091400ef6c123285f221094654d96d35.1587509150.git.robin.murphy@arm.com
-
- 23 Apr, 2020 1 commit
-
-
Lyude Paul authored
This reverts commit 6bb0942e. Unfortunately it would appear that the rumors we've heard of sideband message interleaving not being very well supported are true. On the Lenovo ThinkPad Thunderbolt 3 dock that I have, interleaved messages appear to just get dropped: [drm:drm_dp_mst_wait_tx_reply [drm_kms_helper]] timedout msg send 00000000571ddfd0 2 1 [dp_mst] txmsg cur_offset=2 cur_len=2 seqno=1 state=SENT path_msg=1 dst=00 [dp_mst] type=ENUM_PATH_RESOURCES contents: [dp_mst] port=2 DP descriptor for this hub: OUI 90-cc-24 dev-ID SYNA3 HW-rev 1.0 SW-rev 3.12 quirks 0x0008 It would seem like as well that this is a somewhat well known issue in the field. From section 5.4.2 of the DisplayPort 2.0 specification: There are MST Sink/Branch devices in the field that do not handle interleaved message transactions. To facilitate message transaction handling by downstream devices, an MST Source device shall generate message transactions in an atomic manner (i.e., the MST Source device shall not concurrently interleave multiple message transactions). Therefore, an MST Source device shall clear the Message_Sequence_No value in the Sideband_MSG_Header to 0. MST Source devices that support field policy updates by way of software should update the policy to forego the generation of interleaved message transactions. This is a bit disappointing, as features like HDCP require that we send a sideband request every ~2 seconds for each active stream. However, there isn't really anything in the specification that allows us to accurately probe for interleaved messages. If it ends up being that we -really- need this in the future, we might be able to whitelist hubs where interleaving is known to work-or maybe try some sort of heuristics. But for now, let's just play it safe and not use it. Signed-off-by: Lyude Paul <lyude@redhat.com> Fixes: 6bb0942e ("drm/dp_mst: Remove single tx msg restriction.") Cc: Wayne Lin <Wayne.Lin@amd.com> Cc: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200423164225.680178-1-lyude@redhat.comReviewed-by: Sean Paul <sean@poorly.run>
-
- 21 Apr, 2020 4 commits
-
-
Gal Pressman authored
Fix a couple of typos: "as" -> "has" and "int" -> "in". Signed-off-by: Gal Pressman <galpress@amazon.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20200420074115.23931-1-galpress@amazon.com
-
Souptick Joarder authored
These are dead code since 3.7. If there is no plan to use them further, these can be removed forever. Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com> Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/1587406337-32317-1-git-send-email-jrdr.linux@gmail.com
-
YueHaibing authored
drivers/gpu/drm/gma500/oaktrail_hdmi.c:676:35: warning: ‘hdmi_ids’ defined but not used [-Wunused-const-variable=] static const struct pci_device_id hdmi_ids[] = { ^~~~~~~~ It is never used, remove it. Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20200417101032.8140-1-yuehaibing@huawei.com
-
Geert Uytterhoeven authored
According to https://www.analog.com/, the company name is spelled "Analog Devices". Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20200416103058.15269-4-geert+renesas@glider.be
-
- 20 Apr, 2020 1 commit
-
-
Thomas Zimmermann authored
The ast driver inherits from DRM's CRTC state, but still uses the atomic helper for struct drm_crtc_funcs.reset, drm_atomic_helper_crtc_reset(). The helper only allocates enough memory for the core CRTC state. That results in an out-ouf-bounds access when duplicating the initial CRTC state. Simplified backtrace shown below: [ 21.469321] ================================================================== [ 21.469434] BUG: KASAN: slab-out-of-bounds in ast_crtc_atomic_duplicate_state+0x84/0x100 [ast] [ 21.469445] Read of size 8 at addr ffff888036c1c5f8 by task systemd-udevd/382 [ 21.469451] [ 21.469464] CPU: 2 PID: 382 Comm: systemd-udevd Tainted: G E 5.5.0-rc6-1-default+ #214 [ 21.469473] Hardware name: Sun Microsystems SUN FIRE X2270 M2/SUN FIRE X2270 M2, BIOS 2.05 07/01/2010 [ 21.469480] Call Trace: [ 21.469501] dump_stack+0xb8/0x110 [ 21.469528] print_address_description.constprop.0+0x1b/0x1e0 [ 21.469557] ? ast_crtc_atomic_duplicate_state+0x84/0x100 [ast] [ 21.469581] ? ast_crtc_atomic_duplicate_state+0x84/0x100 [ast] [ 21.469597] __kasan_report.cold+0x1a/0x35 [ 21.469640] ? ast_crtc_atomic_duplicate_state+0x84/0x100 [ast] [ 21.469665] kasan_report+0xe/0x20 [ 21.469693] ast_crtc_atomic_duplicate_state+0x84/0x100 [ast] [ 21.469733] drm_atomic_get_crtc_state+0xbf/0x1c0 [ 21.469768] __drm_atomic_helper_set_config+0x81/0x5a0 [ 21.469803] ? drm_atomic_plane_check+0x690/0x690 [ 21.469843] ? drm_client_rotation+0xae/0x240 [ 21.469876] drm_client_modeset_commit_atomic+0x230/0x390 [ 21.469888] ? __mutex_lock+0x8f0/0xbe0 [ 21.469929] ? drm_client_firmware_config.isra.0+0xa60/0xa60 [ 21.469948] ? drm_client_modeset_commit_force+0x28/0x230 [ 21.470031] ? memset+0x20/0x40 [ 21.470078] drm_client_modeset_commit_force+0x90/0x230 [ 21.470110] drm_fb_helper_restore_fbdev_mode_unlocked+0x5f/0xc0 [ 21.470132] drm_fb_helper_set_par+0x59/0x70 [ 21.470155] fbcon_init+0x61d/0xad0 [ 21.470185] ? drm_fb_helper_restore_fbdev_mode_unlocked+0xc0/0xc0 [ 21.470232] visual_init+0x187/0x240 [ 21.470266] do_bind_con_driver+0x2e3/0x460 [ 21.470321] do_take_over_console+0x20a/0x290 [ 21.470371] do_fbcon_takeover+0x85/0x100 [ 21.470402] register_framebuffer+0x2fd/0x490 [ 21.470425] ? kzalloc.constprop.0+0x10/0x10 [ 21.470503] __drm_fb_helper_initial_config_and_unlock+0xf2/0x140 [ 21.470533] drm_fbdev_client_hotplug+0x162/0x250 [ 21.470563] drm_fbdev_generic_setup+0xd2/0x155 [ 21.470602] ast_driver_load+0x688/0x850 [ast] <...> [ 21.472625] ================================================================== Allocating enough memory for struct ast_crtc_state in a custom ast CRTC reset handler fixes the problem. v2: * implement according to drm_atomic_helper_crtc_reset() * update state with __drm_atomic_helper_crtc_reset() Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Fixes: 83be6a3c ("drm/ast: Introduce struct ast_crtc_state") Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Gerd Hoffmann <kraxel@redhat.com> Cc: Dave Airlie <airlied@redhat.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: "Noralf Trønnes" <noralf@tronnes.org> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200130094012.32140-1-tzimmermann@suse.de
-
- 19 Apr, 2020 1 commit
-
-
Johan Jonker authored
Current dts files with 'hdmi' nodes for rk3066 are manually verified. In order to automate this process rockchip,rk3066-hdmi.txt has to be converted to yaml. Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Link: https://patchwork.freedesktop.org/patch/msgid/20200403133630.7377-1-jbx6244@gmail.com
-
- 17 Apr, 2020 3 commits
-
-
Linus Walleij authored
The Tegra DRM drivers includes the legacy GPIO headers <linux/gpio.h> and <linux/of_gpio.h> but what it really uses is <linux/gpio/consumer.h> since only gpio_desc structs are ever referenced. Include the right header on the top level tegra/drm.h file and drop all the surplus includes. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20200415122427.111769-1-linus.walleij@linaro.org
-
Chuhong Yuan authored
The driver forgets to free the I/O region in remove and probe failure. Add the missed calls to fix it. Since the success of request_region() is optional, add the "region" field in vesafb_par to represent whether request_region() succeeds. Then only call release_region() when "region" is not null. Signed-off-by: Chuhong Yuan <hslester96@gmail.com> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200329145839.20076-1-hslester96@gmail.com
-
Chuhong Yuan authored
The driver forgets to free irq in remove which is requested in probe. Add the missed call to fix it. Also, the position of request_irq() in probe should be put before register_framebuffer(). Signed-off-by: Chuhong Yuan <hslester96@gmail.com> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200324132353.21785-1-hslester96@gmail.com
-