When initially probing the SPI slave device, the call for disabling an
SPI device without the SPI_CS_HIGH flag is not applied, as the
condition for checking whether or not the state to be applied equals the
one currently set evaluates to true.

This however might not necessarily be the case, as the chipselect might
be active.

Add a force flag to spi_set_cs which allows to override this
early exit condition. Set it to false everywhere except when called
from spi_setup to sync up the initial CS state.

Fixes commit d40f0b6f ("spi: Avoid setting the chip select if we don't
need to")
Signed-off-by: David Bauer <mail@david-bauer.net>
Link: https://lore.kernel.org/r/20210416195956.121811-1-mail@david-bauer.netSigned-off-by: Mark Brown <broonie@kernel.org>

The spi controller supports 44-bit address space on AXI in DMA mode,
so set dma_addr_t width to 44-bit to avoid using a swiotlb mapping.
In addition, if dma_map_single fails, it should return immediately
instead of continuing doing the DMA operation which bases on invalid
address.

This fixes the following crash which occurs in reading a big block
from flash:

[  123.633577] zynqmp-qspi ff0f0000.spi: swiotlb buffer is full (sz: 4194304 bytes), total 32768 (slots), used 0 (slots)
[  123.644230] zynqmp-qspi ff0f0000.spi: ERR:rxdma:memory not mapped
[  123.784625] Unable to handle kernel paging request at virtual address 00000000003fffc0
[  123.792536] Mem abort info:
[  123.795313]   ESR = 0x96000145
[  123.798351]   EC = 0x25: DABT (current EL), IL = 32 bits
[  123.803655]   SET = 0, FnV = 0
[  123.806693]   EA = 0, S1PTW = 0
[  123.809818] Data abort info:
[  123.812683]   ISV = 0, ISS = 0x00000145
[  123.816503]   CM = 1, WnR = 1
[  123.819455] user pgtable: 4k pages, 48-bit VAs, pgdp=0000000805047000
[  123.825887] [00000000003fffc0] pgd=0000000803b45003, p4d=0000000803b45003, pud=0000000000000000
[  123.834586] Internal error: Oops: 96000145 [#1] PREEMPT SMP

Fixes: 1c26372e ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210416004652.2975446-6-quanyang.wang@windriver.comSigned-off-by: Mark Brown <broonie@kernel.org>

When handling op->addr, it is using the buffer "tmpbuf" which has been
freed. This will trigger a use-after-free KASAN warning. Let's use
temporary variables to store op->addr.val and op->cmd.opcode to fix
this issue.

Fixes: 1c26372e ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210416004652.2975446-5-quanyang.wang@windriver.comSigned-off-by: Mark Brown <broonie@kernel.org>

During a transfer the driver filled the fifo with 4bytes,
even if the data that needs to be transfer is less that 4bytes.
This resulted in slab-out-of-bounds bug in KernelAddressSanitizer.

This patch resolves slab-out-of-bounds bug by filling the fifo
with the number of bytes that needs to transferred.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20210416004652.2975446-4-quanyang.wang@windriver.comSigned-off-by: Mark Brown <broonie@kernel.org>

After calling platform_set_drvdata(pdev, xqspi) in probe, the return
value of dev_get_drvdata(dev) is a pointer to struct zynqmp_qspi but
not struct spi_controller. A wrong structure type passing to the
functions spi_controller_suspend/resume will hang the system.

And we should check the return value of spi_controller_suspend, if
an error is returned, return it to PM subsystem to stop suspend.

Also, GQSPI_EN_MASK should be written to GQSPI_EN_OFST to enable
the spi controller in zynqmp_qspi_resume since it was disabled in
zynqmp_qspi_suspend before.

Fixes: 1c26372e ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210416004652.2975446-3-quanyang.wang@windriver.comSigned-off-by: Mark Brown <broonie@kernel.org>

The clks "pclk" and "ref_clk" are enabled twice during the probe. The
first time is in the function zynqmp_qspi_probe and the second time is
in zynqmp_qspi_setup_op which is called by devm_spi_register_controller.
Then calling zynqmp_qspi_remove (rmmod this module) to disable these clks
will trigger a warning as below:

[  309.124604] Unpreparing enabled qspi_ref
[  309.128641] WARNING: CPU: 1 PID: 537 at drivers/clk/clk.c:824 clk_core_unprepare+0x108/0x110

Since pm_runtime works now, clks can be enabled/disabled by calling
zynqmp_runtime_suspend/resume. So we don't need to enable these clks
explicitly in zynqmp_qspi_setup_op. Remove them to fix this issue.

And remove clk enabling/disabling in zynqmp_qspi_resume because there is
no spi transfer operation so enabling ref_clk is redundant meanwhile pclk
is not disabled for it is shared with other peripherals.

Furthermore replace clk_enable/disable with clk_prepare_enable and
clk_disable_unprepare in runtime_suspend/resume functions.

Fixes: 1c26372e ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210416004652.2975446-2-quanyang.wang@windriver.comSigned-off-by: Mark Brown <broonie@kernel.org>

Merge branch 'for-5.12' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi into spi-5.13

There is a PM usage counter decrement after zynqmp_qspi_init_hw()
without any refcount increment, which leads to refcount leak.Add
a refcount increment to balance the refcount. Also set
auto_runtime_pm to resume suspended spi controller.

Fixes: 9e3a0003 ("spi: zynqmp: Add pm runtime support")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Tested-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210415074644.24646-1-dinghao.liu@zju.edu.cnSigned-off-by: Mark Brown <broonie@kernel.org>

The match data (struct s3c64xx_spi_port_config) stored in of_device_id
and platform_device_id tables is not modified by the driver and can be
handled entirely in a const-way to increase the code safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sylwester Nawrocki <snawrocki@kernel.org>
Link: https://lore.kernel.org/r/20210414203343.203119-3-krzysztof.kozlowski@canonical.comSigned-off-by: Mark Brown <broonie@kernel.org>

Correct the name of s3c64xx_spi_port_config structure in kerneldoc:

  drivers/spi/spi-s3c64xx.c:154: warning:
    expecting prototype for struct s3c64xx_spi_info. Prototype was for struct s3c64xx_spi_port_config instead
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sylwester Nawrocki <snawrocki@kernel.org>
Link: https://lore.kernel.org/r/20210414203343.203119-2-krzysztof.kozlowski@canonical.comSigned-off-by: Mark Brown <broonie@kernel.org>

Use of_device_get_match_data() to make the code slightly smaller and to
remove the of_device_id table forward declaration.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sylwester Nawrocki <snawrocki@kernel.org>
Link: https://lore.kernel.org/r/20210414203343.203119-1-krzysztof.kozlowski@canonical.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add support for LPSS SPI on Intel Alder Lake PCH-M.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20210415135917.54144-1-jarkko.nikula@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

This series fix a potential interrupt race condition and
cleanup the ACPI protection for the driver.

Change since v1:
- reword the commit in patch #2
Link: https://lore.kernel.org/linux-spi/1617881505-51552-1-git-send-email-yangyicong@hisilicon.com/

Yicong Yang (2):
  spi: hisi-sfc-v3xx: fix potential irq race condition
  spi: hisi-sfc-v3xx: drop unnecessary ACPI_PTR and related ifendif
    protection

 drivers/spi/spi-hisi-sfc-v3xx.c | 7 +++----
 1 file changed, 3 insertions(+), 4 deletions(-)

--
2.8.1

Add the missing unlock before return from function zynqmp_qspi_exec_op()
in the error handling case.

Fixes: a0f65be6 ("spi: spi-zynqmp-gqspi: add mutex locking for exec_op")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210412160025.194171-1-weiyongjun1@huawei.comSigned-off-by: Mark Brown <broonie@kernel.org>

We use ACPI_PTR() and related ifendif protection for the id table.
This is unnecessary as the struct acpi_device_id is defined in
mod_devicetable.h and doesn't rely on ACPI. The driver doesn't
use any ACPI apis, so it can be compiled in the ACPI=n case
with no warnings.

So remove the ACPI_PTR and related ifendif protection, also
replace the header acpi.h with mod_devicetable.h.
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Link: https://lore.kernel.org/r/1618228708-37949-3-git-send-email-yangyicong@hisilicon.comSigned-off-by: Mark Brown <broonie@kernel.org>

We mask the irq when the command completion is timeout. This won't
stop the already running irq handler. Use sychronize_irq() after
we mask the irq, to make sure there is no running handler.
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Link: https://lore.kernel.org/r/1618228708-37949-2-git-send-email-yangyicong@hisilicon.comSigned-off-by: Mark Brown <broonie@kernel.org>

Quanyang Wang <quanyang.wang@windriver.com>:

From: Quanyang Wang <quanyang.wang@windriver.com>

Hello,

This series fix some issues that occurs when the gqspi driver switches to spi-mem framework.

Hi Amit,
I rewrite the "Subject" and "commit message" of these patches, so they
look different from the ones which you reviewed before. I still keep
your "Reviewed-by" and hope you will not mind.

Regards,
Quanyang Wang

Quanyang Wang (4):
  spi: spi-zynqmp-gqspi: use wait_for_completion_timeout to make
    zynqmp_qspi_exec_op not interruptible
  spi: spi-zynqmp-gqspi: add mutex locking for exec_op
  spi: spi-zynqmp-gqspi: transmit dummy circles by using the
    controller's internal functionality
  spi: spi-zynqmp-gqspi: fix incorrect operating mode in
    zynqmp_qspi_read_op

 drivers/spi/spi-zynqmp-gqspi.c | 53 +++++++++++++++++-----------------
 1 file changed, 27 insertions(+), 26 deletions(-)

--
2.25.1

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Use the device_get_match_data() helper instead of open coding.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Suggested-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/1617152319-17701-1-git-send-email-tiantao6@hisilicon.comSigned-off-by: Mark Brown <broonie@kernel.org>

pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Li <wangli74@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210409095458.29921-1-wangli74@huawei.comSigned-off-by: Mark Brown <broonie@kernel.org>

If device_get_match_data returns NULL, devdata isn't being updated
properly. It is being used later in the function. Both devdata and
spi->devdata should be updated to avoid NULL pointer dereference.

Addresses-Coverity: ("NULL pointer dereference")
Fixes: 0e6521f1 ("spi: orion: Use device_get_match_data() helper")
Signed-off-by: Muhammad Usama Anjum <musamaanjum@gmail.com>
Link: https://lore.kernel.org/r/20210408195718.GA3075166@LEGIONSigned-off-by: Mark Brown <broonie@kernel.org>

When some drivers use spi to send data, spi_transfer->speed_hz is
not assigned. If spidev->max_speed_hz is not assigned as well, it
will cause an error in configuring the clock.
Add a check for these two values before configuring the clock. An
error will be returned when they are not assigned.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Link: https://lore.kernel.org/r/20210408103347.244313-2-xiaoning.wang@nxp.comSigned-off-by: Mark Brown <broonie@kernel.org>

Call spi_master_get() holds the reference count to master device, thus
we need an additional spi_master_put() call to reduce the reference
count, otherwise we will leak a reference to master.

This commit fix it by removing the unnecessary spi_master_get().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210409082954.2906933-1-weiyongjun1@huawei.comSigned-off-by: Mark Brown <broonie@kernel.org>

pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.

Fixes: 944c01a8 ("spi: lpspi: enable runtime pm for lpspi")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Li <wangli74@huawei.com>
Link: https://lore.kernel.org/r/20210409095430.29868-1-wangli74@huawei.comSigned-off-by: Mark Brown <broonie@kernel.org>

Use devm_add_action_or_reset() instead of devres_alloc() and
devres_add(), which works the same. This will simplify the
code. There is no functional changes.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Link: https://lore.kernel.org/r/1617843307-53853-1-git-send-email-tiantao6@hisilicon.comSigned-off-by: Mark Brown <broonie@kernel.org>

Call spi_master_get() holds the reference count to master device, thus
we need an additional spi_master_put() call to reduce the reference
count, otherwise we will leak a reference to master.

This commit fix it by removing the unnecessary spi_master_get().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210409082955.2907950-1-weiyongjun1@huawei.comSigned-off-by: Mark Brown <broonie@kernel.org>

When starting a read operation, we should call zynqmp_qspi_setuprxdma
first to set xqspi->mode according to xqspi->bytes_to_receive and
to calculate correct xqspi->dma_rx_bytes. Then in the function
zynqmp_qspi_fillgenfifo, generate the appropriate command with
operating mode and bytes to transfer, and fill the GENFIFO with
the command to perform the read operation.

Calling zynqmp_qspi_fillgenfifo before zynqmp_qspi_setuprxdma will
result in incorrect transfer length and operating mode. So change
the calling order to fix this issue.

Fixes: 1c26372e ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Reviewed-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20210408040223.23134-5-quanyang.wang@windriver.comSigned-off-by: Mark Brown <broonie@kernel.org>

There is a data corruption issue that occurs in the reading operation
(cmd:0x6c) when transmitting common data as dummy circles.

The gqspi controller has the functionality to send dummy clock circles.
When writing data with the fields [receive, transmit, data_xfer] = [0,0,1]
to the Generic FIFO, and configuring the correct SPI mode, the controller
will transmit dummy circles.

So let's switch to hardware dummy cycles transfer to fix this issue.

Fixes: 1c26372e ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Reviewed-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20210408040223.23134-4-quanyang.wang@windriver.comSigned-off-by: Mark Brown <broonie@kernel.org>

The spi-mem framework has no locking to prevent ctlr->mem_ops->exec_op
from concurrency. So add the locking to zynqmp_qspi_exec_op.

Fixes: 1c26372e ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Reviewed-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20210408040223.23134-3-quanyang.wang@windriver.comSigned-off-by: Mark Brown <broonie@kernel.org>

spi: spi-zynqmp-gqspi: use wait_for_completion_timeout to make zynqmp_qspi_exec_op not interruptible

When Ctrl+C occurs during the process of zynqmp_qspi_exec_op, the function
wait_for_completion_interruptible_timeout will return a non-zero value
-ERESTARTSYS immediately. This will disrupt the SPI memory operation
because the data transmitting may begin before the command or address
transmitting completes. Use wait_for_completion_timeout to prevent
the process from being interruptible.

This patch fixes the error as below:
root@xilinx-zynqmp:~# flash_erase /dev/mtd3 0 0
Erasing 4 Kibyte @ 3d000 --  4 % complete
    (Press Ctrl+C)
[  169.581911] zynqmp-qspi ff0f0000.spi: Chip select timed out
[  170.585907] zynqmp-qspi ff0f0000.spi: Chip select timed out
[  171.589910] zynqmp-qspi ff0f0000.spi: Chip select timed out
[  172.593910] zynqmp-qspi ff0f0000.spi: Chip select timed out
[  173.597907] zynqmp-qspi ff0f0000.spi: Chip select timed out
[  173.603480] spi-nor spi0.0: Erase operation failed.
[  173.608368] spi-nor spi0.0: Attempted to modify a protected sector.

Fixes: 1c26372e ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Reviewed-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20210408040223.23134-2-quanyang.wang@windriver.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add the missing iounmap() before return from of_fsl_spi_probe()
in the error handling case.

Fixes: 0f0581b2 ("spi: fsl: Convert to use CS GPIO descriptors")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210401140350.1677925-1-yangyingliang@huawei.comSigned-off-by: Mark Brown <broonie@kernel.org>

A previous refactoring moved the chip select number handling
to the SPI core and we missed a leftover platform data user
in the ST spear platform. The spear is not using this
chipselect or PL022 for anything and should be using device
tree like the rest of the platform so just delete the
offending platform data.

Cc: Viresh Kumar <vireshk@kernel.org>
Cc: Shiraz Hashim <shiraz.linux.kernel@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20210408075045.3435046-1-linus.walleij@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

We can't rely on the contents of the devres list during
spi_unregister_controller(), as the list is already torn down at the
time we perform devres_find() for devm_spi_release_controller. This
causes devices registered with devm_spi_alloc_{master,slave}() to be
mistakenly identified as legacy, non-devm managed devices and have their
reference counters decremented below 0.

------------[ cut here ]------------
WARNING: CPU: 1 PID: 660 at lib/refcount.c:28 refcount_warn_saturate+0x108/0x174
[<b0396f04>] (refcount_warn_saturate) from [<b03c56a4>] (kobject_put+0x90/0x98)
[<b03c5614>] (kobject_put) from [<b0447b4c>] (put_device+0x20/0x24)
 r4:b6700140
[<b0447b2c>] (put_device) from [<b07515e8>] (devm_spi_release_controller+0x3c/0x40)
[<b07515ac>] (devm_spi_release_controller) from [<b045343c>] (release_nodes+0x84/0xc4)
 r5:b6700180 r4:b6700100
[<b04533b8>] (release_nodes) from [<b0454160>] (devres_release_all+0x5c/0x60)
 r8:b1638c54 r7:b117ad94 r6:b1638c10 r5:b117ad94 r4:b163dc10
[<b0454104>] (devres_release_all) from [<b044e41c>] (__device_release_driver+0x144/0x1ec)
 r5:b117ad94 r4:b163dc10
[<b044e2d8>] (__device_release_driver) from [<b044f70c>] (device_driver_detach+0x84/0xa0)
 r9:00000000 r8:00000000 r7:b117ad94 r6:b163dc54 r5:b1638c10 r4:b163dc10
[<b044f688>] (device_driver_detach) from [<b044d274>] (unbind_store+0xe4/0xf8)

Instead, determine the devm allocation state as a flag on the
controller which is guaranteed to be stable during cleanup.

Fixes: 5e844cc3 ("spi: Introduce device-managed SPI controller allocation")
Signed-off-by: William A. Kennington III <wak@google.com>
Link: https://lore.kernel.org/r/20210407095527.2771582-1-wak@google.comSigned-off-by: Mark Brown <broonie@kernel.org>

When platform_get_irq() fails, a pairing PM usage counter
increment is needed to keep the counter balanced. It's the
same for the following error paths.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20210408092559.3824-1-dinghao.liu@zju.edu.cnSigned-off-by: Mark Brown <broonie@kernel.org>

Use the device_get_match_data() helper instead of open coding.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Link: https://lore.kernel.org/r/1617258288-1490-1-git-send-email-tiantao6@hisilicon.comSigned-off-by: Mark Brown <broonie@kernel.org>

Fix warning Woverflow on type conversion reported on x86_64:

  drivers/spi/spi-hisi-kunpeng.c:361:9: warning: conversion from 'long unsigned int' to 'u32'
  {aka 'unsigned int'} changes value from '18446744073709551600' to '4294967280' [-Woverflow]

The registers are 32 bit, so fix by casting to u32.

Fixes: c770d863 ("spi: Add HiSilicon SPI Controller Driver for Kunpeng SoCs")
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1617762660-54681-1-git-send-email-f.fangjian@huawei.comSigned-off-by: Mark Brown <broonie@kernel.org>

struct spi_transfer is declared twice. One is declared at 24th line.
The blew one is not needed though. Remove the duplicate.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Link: https://lore.kernel.org/r/20210401065904.994121-1-wanjiabing@vivo.comSigned-off-by: Mark Brown <broonie@kernel.org>

Hi,

This series picks up Ramuthevar's effort on converting the Cadence QSPI
bindings to yaml [0]. During the conversion process, I discovered that
some TI device tree files were not using the compatible correctly. Those
are fixed in patches 1-3.

[0] https://patchwork.kernel.org/project/spi-devel-general/patch/20201116031003.19062-6-vadivel.muruganx.ramuthevar@linux.intel.com/

Pratyush Yadav (3):
  arm64: dts: ti: k3-j721e-mcu: Fix ospi compatible
  arm64: dts: ti: k3-j7200-mcu: Fix ospi compatible
  arm64: dts: ti: k3-am64-main: Fix ospi compatible

Ramuthevar Vadivel Murugan (1):
  dt-bindings: spi: Convert cadence-quadspi.txt to cadence-quadspi.yaml

 .../bindings/spi/cadence-quadspi.txt          |  68 ---------
 .../bindings/spi/cdns,qspi-nor.yaml           | 143 ++++++++++++++++++
 arch/arm64/boot/dts/ti/k3-am64-main.dtsi      |   2 +-
 .../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi      |   2 +-
 .../boot/dts/ti/k3-j721e-mcu-wakeup.dtsi      |   4 +-
 5 files changed, 147 insertions(+), 72 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/spi/cadence-quadspi.txt
 create mode 100644 Documentation/devicetree/bindings/spi/cdns,qspi-nor.yaml

--
2.30.0

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

There is no way as of now to have a parent or bus defining properties
for child nodes. For now, avoid it in the example to silence warnings on
dt_schema_check. We can figure out how to deal with actual dts files
later.

[p.yadav@ti.com: Fix how compatible is defined, make reset optional, fix
minor typos, remove subnode properties in example, update commit
message.]
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210326130034.15231-5-p.yadav@ti.comSigned-off-by: Mark Brown <broonie@kernel.org>

This driver supports SPI Controller for HiSilicon Kunpeng SoCs. This
driver supports SPI operations using FIFO mode of transfer.

DMA is not supported, and we just use IRQ mode for operation completion
notification.

Only ACPI firmware is supported.
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1616836200-45827-1-git-send-email-f.fangjian@huawei.comSigned-off-by: Mark Brown <broonie@kernel.org>

This converts the PL022 driver to use GPIO descriptors
instead of the old global GPIO numberspace. Since the
driver handles messages on its own it needs to manage
the GPIO descriptor directly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210330164907.2346010-3-linus.walleij@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>