The struct driver_info ax88178_info is assigned the function
asix_rx_fixup_common as it's rx_fixup callback. This means that
FLAG_MULTI_PACKET must be set as this function is cloning the
data and calling usbnet_skb_return. Not setting this flag leads
to usbnet_skb_return beeing called a second time from within
the rx_process function in the usbnet module.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Reported-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

Even if the 'time_before' macro expand with parentheses, the look is bad.
Signed-off-by: Francois-Xavier Le Bail <fx.lebail@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

phy_init_hw not does a full PHY reset after the driver probe has
finished, so any hw initialization done in the probe will be lost.
Part of the timestamping functionality of the dp83640 is set up in the
probe and with that lost, enabling timestamping will cause a PHY
lockup, requiring a hard reset / power cycle to recover.

This patch moves all the HW initialization in dp83640_probe to
dp83640_config_init.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 0cd8f9cc ("drivers: net: cpsw:
enable promiscuous mode support")

Enable promiscuous mode support for CPSW.

Introduced a crash on an am335x based board (similiar to am335x-evm).
Reason is buggy end condition in for loop in cpsw_set_promiscious()

for (i = 0; i <= priv->data.slaves; i++)

should be

for (i = 0; i < priv->data.slaves; i++)

Fix this ...
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Markus Pargmann <mpa@pengutronix.de>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vhost_zerocopy_callback accesses VQ right after it drops a ubuf
reference.  In theory, this could race with device removal which waits
on the ubuf kref, and crash on use after free.

Do all accesses within rcu read side critical section, and synchronize
on release.

Since callbacks are always invoked from bh, synchronize_rcu_bh seems
enough and will help release complete a bit faster.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vhost checked the counter within the refcnt before decrementing.  It
really wanted to know that it is the one that has the last reference, as
a way to batch freeing resources a bit more efficiently.

Note: we only let refcount go to 0 on device release.

This works well but we now access the ref counter twice so there's a
race: all users might see a high count and decide to defer freeing
resources.
In the end no one initiates freeing resources until the last reference
is gone (which is on VM shotdown so might happen after a looooong time).

Let's do what we probably should have done straight away:
switch from kref to plain atomic, documenting the
semantics, return the refcount value atomically after decrement,
then use that to avoid the deadlock.
Reported-by: Qin Chuanyu <qinchuanyu@huawei.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Liu Junliang <liujunliang_ljl@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use %zu for size_t in order to avoid the following build
warning in printks.

drivers/net/usb/sr9800.c: In function 'sr9800_bind'
drivers/net/usb/sr9800.c:826:2: warning: format '%ld' expects argument of type 'long int' but argument 5 has type 'size_t'
[-Wformat]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix incorrect comment reported by Norbert Kiesel. Edit another comment to add
more details. Also add references to algorithm (IETF draft and paper) to top of
file.
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
CC: Mythili Prabhu <mysuryan@cisco.com>
CC: Norbert Kiesel <nkiesel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It's wrong if the device tree doesn't provide a phy-mode property for
the cpsw slaves as it is documented to be required in
Documentation/devicetree/bindings/net/cpsw.txt.

Anyhow it's nice to catch that problem, still more as it used to work
without this property up to commit 388367a5 (drivers: net: cpsw: use
cpsw-phy-sel driver to configure phy mode) which is in v3.13-rc1.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the PXS8 and PHS8 devices show up with PID 0x0053 they will expose both a
QMI port and a WWAN interface.

CC: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
CC: Christian Schmiedl <christian.schmiedl@gemalto.com>
CC: Nicolaus Colberg <nicolaus.colberg@gemalto.com>
CC: David McCullough <david.mccullough@accelecon.com>
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

linux-can-fixes-for-3.14-20140212

Marc Kleine-Budde says:

====================
this is a pull request with one patch for net/master, for the current release
cycle. Olivier Sobrie noticed and fixed that the kvaser_usb driver doesn't
check the number of channels value from the hardware, which may result in
writing over the bounds of an array in the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Warning log:
xilinx_axienet_main.c: In function 'axienet_start_xmit_done':
xilinx_axienet_main.c:617:16: warning: operation on 'lp->tx_bd_ci' may be undefined [-Wsequence-point]
xilinx_axienet_main.c: In function 'axienet_start_xmit':
xilinx_axienet_main.c:703:18: warning: operation on 'lp->tx_bd_tail' may be undefined [-Wsequence-point]
xilinx_axienet_main.c:719:17: warning: operation on 'lp->tx_bd_tail' may be undefined [-Wsequence-point]
xilinx_axienet_main.c: In function 'axienet_recv':
xilinx_axienet_main.c:792:16: warning: operation on 'lp->rx_bd_ci' may be undefined [-Wsequence-point]
xilinx_axienet_main.c: In function 'axienet_of_probe':
xilinx_axienet_main.c:1501:21: warning: unused variable 'rc' [-Wunused-variable]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add missing header to fix compilation error.
drivers/net/ethernet/xilinx/xilinx_axienet_main.c:1575:22:
 error: undefined identifier 'irq_of_parse_and_map'
drivers/net/ethernet/xilinx/xilinx_axienet_main.c:1576:22:
 error: undefined identifier 'irq_of_parse_and_map'
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marcelo Ricardo Leitner reported problems when the forwarding link path
has a lower mtu than the incoming one if the inbound interface supports GRO.

Given:
Host <mtu1500> R1 <mtu1200> R2

Host sends tcp stream which is routed via R1 and R2.  R1 performs GRO.

In this case, the kernel will fail to send ICMP fragmentation needed
messages (or pkt too big for ipv6), as GSO packets currently bypass dstmtu
checks in forward path. Instead, Linux tries to send out packets exceeding
the mtu.

When locking route MTU on Host (i.e., no ipv4 DF bit set), R1 does
not fragment the packets when forwarding, and again tries to send out
packets exceeding R1-R2 link mtu.

This alters the forwarding dstmtu checks to take the individual gso
segment lengths into account.

For ipv6, we send out pkt too big error for gso if the individual
segments are too big.

For ipv4, we either send icmp fragmentation needed, or, if the DF bit
is not set, perform software segmentation and let the output path
create fragments when the packet is leaving the machine.
It is not 100% correct as the error message will contain the headers of
the GRO skb instead of the original/segmented one, but it seems to
work fine in my (limited) tests.

Eric Dumazet suggested to simply shrink mss via ->gso_size to avoid
sofware segmentation.

However it turns out that skb_segment() assumes skb nr_frags is related
to mss size so we would BUG there.  I don't want to mess with it considering
Herbert and Eric disagree on what the correct behavior should be.

Hannes Frederic Sowa notes that when we would shrink gso_size
skb_segment would then also need to deal with the case where
SKB_MAX_FRAGS would be exceeded.

This uses sofware segmentation in the forward path when we hit ipv4
non-DF packets and the outgoing link mtu is too small.  Its not perfect,
but given the lack of bug reports wrt. GRO fwd being broken this is a
rare case anyway.  Also its not like this could not be improved later
once the dust settles.
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Reported-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Will be used by upcoming ipv4 forward path change that needs to
determine feature mask using skb->dst->dev instead of skb->dev.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bonding driver take write locks and spin locks that are shared
by the tx path in enslave processing and notification processing,
If the netconsole is in use, the bonding can call printk which puts
us in the netpoll tx path, if the netconsole is attached to the bonding
driver, result in deadlock.

So add protection for these place, by checking the netpoll_block_tx
state, we can defer the sending of the netconsole frames until a later
time using the retransmit feature of netpoll_send_skb that is triggered
on the return code NETDEV_TX_BUSY.

Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the commit 0e245dba
("drivers/net: delete the 3Com 3c505/3c507 intel i825xx support")
we clobbered the 3c505 driver (over a year ago) along with other
abandoned ISA drivers.

However, this orphaned README file escaped detection at that
time, and has lived on until today. Get rid of it now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Here, when the net is init_net, we needn't to kmemdup the ctl_table
again. So add a check for net. Also we can save some memory.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As commit 3c68198e("sctp: Make hmac algorithm selection for
 cookie generation dynamic"), we miss the .data initialization.
If we don't use the net_namespace, the problem that parts of the
sysctl configuration won't be isolation and won't occur.

In sctp_sysctl_net_register(), we register the sysctl for each
net, in the for(), we use the 'table[i].data' as check condition, so
when the 'i' is the index of sctp_hmac_alg, the data is NULL, then
break. So add the .data initialization.
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I saw the following BUG when ->newlink() fails in rtnl_newlink():

[   40.240058] kernel BUG at net/core/dev.c:6438!

this is due to free_netdev() is not supposed to be called before
netdev is completely unregistered, therefore it is not correct
to call free_netdev() here, at least for ops->newlink!=NULL case,
many drivers call it in ->destructor so that rtnl_unlock() will
take care of it, we probably don't need to do anything here.

Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rtnl_newlink() doesn't unregister it for us on failure.

Cc: Patrick McHardy <kaber@trash.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If a packet received on a link is out-of-sequence, it will be
placed on a deferred queue and later reinserted in the receive
path once the preceding packets have been processed. The problem
with this is that it will be subject to the buffer adjustment from
link_recv_buf_validate twice. The second adjustment for 20 bytes
header space will corrupt the packet.

We solve this by tagging the deferred packets and bail out from
receive buffer validation for packets that have already been
subjected to this.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

STi series SOCs have a glue layer on top of the synopsis gmac IP, this
glue layer needs to be configured before the gmac driver starts using
the IP.

This patch adds a support to this glue layer which is configured via
stmmac setup, init, exit callbacks.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The netlink kind (and iproute2 type option) is actually called
'macvtap', not 'macvlan'.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is needed to check the number of channels returned by the HW because it
cannot be greater than MAX_NET_DEVICES otherwise it will crash.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Pull microblaze fixes from Michal Simek:
 - Fix two compilation issues - HZ, readq/writeq
 - Fix stack protection support

* tag 'microblaze-3.14-rc3' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: Fix a typo when disabling stack protection
  microblaze: Define readq and writeq IO helper function
  microblaze: Fix missing HZ macro

Pull s390 bugfixes from Martin Schwidefsky:
 "A collection a bug fixes.  Most of them are minor but two of them are
  more severe.  The linkage stack bug can be used by user space to force
  an oops, with panic_on_oops this is a denial-of-service.  And the dump
  memory detection issue can cause incomplete memory dumps"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/cio: improve cio_commit_config
  s390: fix kernel crash due to linkage stack instructions
  s390/dump: Fix dump memory detection
  s390/appldata: restore missing init_virt_timer()
  s390/qdio: correct program-controlled interruption checking
  s390/qdio: for_each macro correctness

Pull networking updates from David Miller:

 1) Fix flexcan build on big endian, from Arnd Bergmann

 2) Correctly attach cpsw to GPIO bitbang MDIO drive, from Stefan Roese

 3) udp_add_offload has to use GFP_ATOMIC since it can be invoked from
    non-sleepable contexts.  From Or Gerlitz

 4) vxlan_gro_receive() does not iterate over all possible flows
    properly, fix also from Or Gerlitz

 5) CAN core doesn't use a proper SKB destructor when it hooks up
    sockets to SKBs.  Fix from Oliver Hartkopp

 6) ip_tunnel_xmit() can use an uninitialized route pointer, fix from
    Eric Dumazet

 7) Fix address family assignment in IPVS, from Michal Kubecek

 8) Fix ath9k build on ARM, from Sujith Manoharan

 9) Make sure fail_over_mac only applies for the correct bonding modes,
    from Ding Tianhong

10) The udp offload code doesn't use RCU correctly, from Shlomo Pongratz

11) Handle gigabit features properly in generic PHY code, from Florian
    Fainelli

12) Don't blindly invoke link operations in
    rtnl_link_get_slave_info_data_size, they are optional.  Fix from
    Fernando Luis Vazquez Cao

13) Add USB IDs for Netgear Aircard 340U, from Bjørn Mork

14) Handle netlink packet padding properly in openvswitch, from Thomas
    Graf

15) Fix oops when deleting chains in nf_tables, from Patrick McHardy

16) Fix RX stalls in xen-netback driver, from Zoltan Kiss

17) Fix deadlock in mac80211 stack, from Emmanuel Grumbach

18) inet_nlmsg_size() forgets to consider ifa_cacheinfo, fix from Geert
    Uytterhoeven

19) tg3_change_mtu() can deadlock, fix from Nithin Sujir

20) Fix regression in setting SCTP local source addresses on accepted
    sockets, caused by some generic ipv6 socket changes.  Fix from
    Matija Glavinic Pecotic

21) IPPROTO_* must be pure defines, otherwise module aliases don't get
    constructed properly.  Fix from Jan Moskyto

22) IPV6 netconsole setup doesn't work properly unless an explicit
    source address is specified, fix from Sabrina Dubroca

23) Use __GFP_NORETRY for high order skb page allocations in
    sock_alloc_send_pskb and skb_page_frag_refill.  From Eric Dumazet

24) Fix a regression added in netconsole over bridging, from Cong Wang

25) TCP uses an artificial offset of 1ms for SRTT, but this doesn't jive
    well with TCP pacing which needs the SRTT to be accurate.  Fix from
    Eric Dumazet

26) Several cases of missing header file includes from Rashika Kheria

27) Add ZTE MF667 device ID to qmi_wwan driver, from Raymond Wanyoike

28) TCP Small Queues doesn't handle nonagle properly in some corner
    cases, fix from Eric Dumazet

29) Remove extraneous read_unlock in bond_enslave, whoops.  From Ding
    Tianhong

30) Fix 9p trans_virtio handling of vmalloc buffers, from Richard Yao

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (136 commits)
  6lowpan: fix lockdep splats
  alx: add missing stats_lock spinlock init
  9p/trans_virtio.c: Fix broken zero-copy on vmalloc() buffers
  bonding: remove unwanted bond lock for enslave processing
  USB2NET : SR9800 : One chip USB2.0 USB2NET SR9800 Device Driver Support
  tcp: tsq: fix nonagle handling
  bridge: Prevent possible race condition in br_fdb_change_mac_address
  bridge: Properly check if local fdb entry can be deleted when deleting vlan
  bridge: Properly check if local fdb entry can be deleted in br_fdb_delete_by_port
  bridge: Properly check if local fdb entry can be deleted in br_fdb_change_mac_address
  bridge: Fix the way to check if a local fdb entry can be deleted
  bridge: Change local fdb entries whenever mac address of bridge device changes
  bridge: Fix the way to find old local fdb entries in br_fdb_change_mac_address
  bridge: Fix the way to insert new local fdb entries in br_fdb_changeaddr
  bridge: Fix the way to find old local fdb entries in br_fdb_changeaddr
  tcp: correct code comment stating 3 min timeout for FIN_WAIT2, we only do 1 min
  net: vxge: Remove unused device pointer
  net: qmi_wwan: add ZTE MF667
  3c59x: Remove unused pointer in vortex_eisa_cleanup()
  net: fix 'ip rule' iif/oif device rename
  ...

When a device ndo_start_xmit() calls again dev_queue_xmit(),
lockdep can complain because dev_queue_xmit() is re-entered and the
spinlocks protecting tx queues share a common lockdep class.

Same issue was fixed for bonding/l2tp/ppp in commits

0daa2303 ("[PATCH] bonding: lockdep annotation")
49ee4920 ("bonding: set qdisc_tx_busylock to avoid LOCKDEP splat")
23d3b8bf ("net: qdisc busylock needs lockdep annotations ")
303c07db ("ppp: set qdisc_tx_busylock to avoid LOCKDEP splat ")
Reported-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Trivial fix for init time stack trace occuring in
alx_get_stats64 upon start up. Should have been part of
commit adding the spinlock:
f1b6b106 alx: add alx_get_stats64 operation
Signed-off-by: John Greene <jogreene@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 9p-virtio transport does zero copy on things larger than 1024 bytes
in size. It accomplishes this by returning the physical addresses of
pages to the virtio-pci device. At present, the translation is usually a
bit shift.

That approach produces an invalid page address when we read/write to
vmalloc buffers, such as those used for Linux kernel modules. Any
attempt to load a Linux kernel module from 9p-virtio produces the
following stack.

[<ffffffff814878ce>] p9_virtio_zc_request+0x45e/0x510
[<ffffffff814814ed>] p9_client_zc_rpc.constprop.16+0xfd/0x4f0
[<ffffffff814839dd>] p9_client_read+0x15d/0x240
[<ffffffff811c8440>] v9fs_fid_readn+0x50/0xa0
[<ffffffff811c84a0>] v9fs_file_readn+0x10/0x20
[<ffffffff811c84e7>] v9fs_file_read+0x37/0x70
[<ffffffff8114e3fb>] vfs_read+0x9b/0x160
[<ffffffff81153571>] kernel_read+0x41/0x60
[<ffffffff810c83ab>] copy_module_from_fd.isra.34+0xfb/0x180

Subsequently, QEMU will die printing:

qemu-system-x86_64: virtio: trying to map MMIO memory

This patch enables 9p-virtio to correctly handle this case. This not
only enables us to load Linux kernel modules off virtfs, but also
enables ZFS file-based vdevs on virtfs to be used without killing QEMU.

Special thanks to both Avi Kivity and Alexander Graf for their
interpretation of QEMU backtraces. Without their guidence, tracking down
this bug would have taken much longer. Also, special thanks to Linus
Torvalds for his insightful explanation of why this should use
is_vmalloc_addr() instead of is_vmalloc_or_module_addr():

https://lkml.org/lkml/2014/2/8/272Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bond enslave processing don't hold bond->lock anymore,
so release an unlocked rw lock will cause warning message,
remove the unwanted read_unlock(&bond->lock).

Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Liu Junliang <liujunliang_ljl@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge misc fixes from Andrew Morton:
 "A bunch of fixes"

* emailed patches fron Andrew Morton <akpm@linux-foundation.org>:
  ocfs2: check existence of old dentry in ocfs2_link()
  ocfs2: update inode size after zeroing the hole
  ocfs2: fix issue that ocfs2_setattr() does not deal with new_i_size==i_size
  mm/memory-failure.c: move refcount only in !MF_COUNT_INCREASED
  smp.h: fix x86+cpu.c sparse warnings about arch nonboot CPU calls
  mm: fix page leak at nfs_symlink()
  slub: do not assert not having lock in removing freed partial
  gitignore: add all.config
  ocfs2: fix ocfs2_sync_file() if filesystem is readonly
  drivers/edac/edac_mc_sysfs.c: poll timeout cannot be zero
  fs/file.c:fdtable: avoid triggering OOMs from alloc_fdmem
  xen: properly account for _PAGE_NUMA during xen pte translations
  mm/slub.c: list_lock may not be held in some circumstances
  drivers/md/bcache/extents.c: use %zi to format size_t
  vmcore: prevent PT_NOTE p_memsz overflow during header update
  drivers/message/i2o/i2o_config.c: fix deadlock in compat_ioctl(I2OGETIOPS)
  Documentation/: update 00-INDEX files
  checkpatch: fix detection of git repository
  get_maintainer: fix detection of git repository
  drivers/misc/sgi-gru/grukdump.c: unlocking should be conditional in gru_dump_context()

System call linkat first calls user_path_at(), check the existence of
old dentry, and then calls vfs_link()->ocfs2_link() to do the actual
work.  There may exist a race when Node A create a hard link for file
while node B rm it.

         Node A                          Node B
user_path_at()
  ->ocfs2_lookup(),
find old dentry exist
                                rm file, add inode say inodeA
                                to orphan_dir

call ocfs2_link(),create a
hard link for inodeA.

                                rm the link, add inodeA to orphan_dir
                                again

When orphan_scan work start, it calls ocfs2_queue_orphans() to do the
main work.  It first tranverses entrys in orphan_dir, linking all inodes
in this orphan_dir to a list look like this:

	inodeA->inodeB->...->inodeA

When tranvering this list, it will fall into loop, calling iput() again
and again.  And finally trigger BUG_ON(inode->i_state & I_CLEAR).
Signed-off-by: joyce <xuejiufei@huawei.com>
Reviewed-by: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs-writeback will release the dirty pages without page lock whose offset
are over inode size, the release happens at
block_write_full_page_endio().  If not update, dirty pages in file holes
may be released before flushed to the disk, then file holes will contain
some non-zero data, this will cause sparse file md5sum error.

To reproduce the bug, find a big sparse file with many holes, like vm
image file, its actual size should be bigger than available mem size to
make writeback work more frequently, tar it with -S option, then keep
untar it and check its md5sum again and again until you get a wrong
md5sum.
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Younger Liu <younger.liu@huawei.com>
Reviewed-by: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The issue scenario is as following:

- Create a small file and fallocate a large disk space for a file with
  FALLOC_FL_KEEP_SIZE option.

- ftruncate the file back to the original size again.  but the disk free
  space is not changed back.  This is a real bug that be fixed in this
  patch.

In order to solve the issue above, we modified ocfs2_setattr(), if
attr->ia_size != i_size_read(inode), It calls ocfs2_truncate_file(), and
truncate disk space to attr->ia_size.
Signed-off-by: Younger Liu <younger.liu@huawei.com>
Reviewed-by: Jie Liu <jeff.liu@oracle.com>
Tested-by: Jie Liu <jeff.liu@oracle.com>
Cc: Joel Becker <jlbec@evilplan.org>
Reviewed-by: Mark Fasheh <mfasheh@suse.de>
Cc: Sunil Mushran <sunil.mushran@gmail.com>
Reviewed-by: Jensen <shencanquan@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mce-test detected a test failure when injecting error to a thp tail
page.  This is because we take page refcount of the tail page in
madvise_hwpoison() while the fix in commit a3e0f9e4
("mm/memory-failure.c: transfer page count from head page to tail page
after split thp") assumes that we always take refcount on the head page.

When a real memory error happens we take refcount on the head page where
memory_failure() is called without MF_COUNT_INCREASED set, so it seems
to me that testing memory error on thp tail page using madvise makes
little sense.

This patch cancels moving refcount in !MF_COUNT_INCREASED for valid
testing.

[akpm@linux-foundation.org: s/&&/&/]
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Cc: Chen Gong <gong.chen@linux.intel.com>
Cc: <stable@vger.kernel.org>	[3.9+: a3e0f9e4]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Use what we already do for arch_disable_smp_support() to fix these:

  arch/x86/kernel/smpboot.c:1155:6: warning: symbol 'arch_enable_nonboot_cpus_begin' was not declared. Should it be static?
  arch/x86/kernel/smpboot.c:1160:6: warning: symbol 'arch_enable_nonboot_cpus_end' was not declared. Should it be static?
  kernel/cpu.c:512:13: warning: symbol 'arch_enable_nonboot_cpus_begin' was not declared. Should it be static?
  kernel/cpu.c:516:13: warning: symbol 'arch_enable_nonboot_cpus_end' was not declared. Should it be static?
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>