Call iwl_probe with a ready iwl_bus struct. This means that the bus layer
assigns the irq, dev and iwl_bus_ops pointers to iwl_bus before giving it to
iwl_probe.

The device specific struct is allocated together with the common iwl_bus struct
by the bus specific layer. The pointer to the aggregate struct is passed to the
upper layer that holds a pointer to iwl_bus instead of an embedded iw_bus.
The private data given to the PCI subsystem is now iwl_bus and not iwl_priv.

Provide bus_* inliners on the way in order  to simplify the syntax.

Rename iwl-pci.h -> iwl-bus.h since it is bus agnostic and represent the
external of the bus layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

It still holds a pointer to iwl_priv. But hopefully this will disappear at some point.
Also add the multiple inclusion protection to iwl-trans.h that was forgotten.
Move iwl-trans structures to iwl-trans.h
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

This function is really related to the transport layer - move it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Basically all the nic_init flow should be in the transport layer.
iwl_prepare_card_hw will move to the transport too in a separate patch.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

All the configurations of the HW for AMPDU are now in the transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

For temperature offset calibration, send radio sensor offset in le16 format
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Use the valid calibration mask for init calibration
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

IWL_PHY_CALIBRATE_DIFF_GAIN_CMD is for legacy device, remove it
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Set calibration config flag for complete notification
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Since iwlagn_setup_deferred_work is always called, fold it into
iwl_setup_deferred_work. BT related works are setup by the new
bt_setup_deferred_work lib_ops.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.guy@intel.com>

Since iwlagn_rx_handler_setup is always called, fold it into
iwl_rx_handler_setup. BT related handlers are setup by the new
bt_rx_handler_setup lib_ops.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.guy@intel.com>

kick_nic means to remove the RESET bit from the embedded CPU
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.guy@intel.com>

Previously, the mesh was running whenever the appropriate hardware
and firmware was present.

Now we only run the mesh when the interface is running.

Also simplifies interface management a little.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Remove unused blindlist code.

Mark a few items const and static where possible. Involved some
code re-ordering, but no code changes.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: "Luis R. Rodriguez" <lrodriguez@atheros.com>
Cc: ath9k-devel@lists.ath9k.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

commit 58389c69150e6032504dfcd3edca6b1975c8b5bc
Author: Johannes Berg <johannes.berg@intel.com>
Date:   Mon Jul 18 18:08:35 2011 +0200

     cfg80211: allow userspace to control supported rates in scan

made single-band cards crash since it would always
access all wiphy->bands[]. Fix this and reject any
attempts in the new helper ieee80211_get_ratemask()
to do the same, rejecting rates configuration for
unsupported bands.
Reported-by: Pavel Roskin <proski@gnu.org>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ieee80211_stop_rx_ba_session() was calling sta_info_get()
without rcu locking, and the return value was not
checked.
This resulted in the following panic:

[<bf05726c>] (ieee80211_stop_rx_ba_session+0x0/0x60 [mac80211])
[<bf0abd94>] (wl1271_event_handle+0x0/0xdc8 [wl12xx])
[<bf0a7308>] (wl1271_irq+0x0/0x4a0 [wl12xx])
[<c00c40a8>] (irq_thread+0x0/0x254)
[<c00a7398>] (kthread+0x0/0x8c)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211_netdev_notifier_call() is configuring psm in case
of NL80211_IFTYPE_STATION interface type (on NETDEV_UP).
do the same for NL80211_IFTYPE_P2P_CLIENT interface type.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In P2P client mode, the GO (AP) to connect to might
have periods of time where it is not available due
to powersave. To allow the driver to sync with it
and send frames to the GO only when it is available
add a new callback tx_sync (and the corresponding
finish_tx_sync). These callbacks can sleep unlike
the actual TX.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Both ath5k_hw and ath5k_softc represent one instance of the hardware.
This duplication is historical and is not needed anymore.

Keep the name "ath5k_hw" for the merged structure and "ah" for the
variable pointing to it.  "ath5k_hw" is shorter than "ath5k_softc", more
descriptive and more widely used.

Put the combined structure to ath5k.h where the old ath5k_softc used to
be. Move some code from base.h to ath5k.h as needed.

Remove memory allocation for struct ath5k_hw and the corresponding error
handling.  Merge iobase and ah_iobase fields.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Recent experiments have shown many cores share 0x1E0 register used for
clock management.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some of the newer Broadcom chipsets have longe names like BCM43224,
BCM43225, etc. However Broadcom decided to keep using u16 for storing
them. Use %X or %d depending on chip_id value to avoid BCMA8D8, etc.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Scanning currently uses the TX rate mask to
restrict the rate set, which is bogus. Make
it use the new set of rates from userspace.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some P2P scans are not allowed to advertise
11b rates, but that is a rather special case
so instead of having that, allow userspace
to request the rate sets (per band) that are
advertised in scan probe request frames.

Since it's needed in two places now, factor
out some common code parsing a rate array.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Old masks were causing ugly, delayed lock ups.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

These are needed by ath6kl for parsing tspec status from an IE.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some cards do not use additional 0x30 offset for SPROM location. We do
not know the real condition for it yet, make it BCM4331 specific for
now.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Following operation was incorrectly translated:
 radio_read(0x0011) -> 0xffff
radio_write(0x0011) <- 0xfff7
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Also change the default channel to 11. This is the first channel closed
driver switches to.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>