- 20 Sep, 2012 21 commits
-
-
Lekensteyn authored
This is rather a hack to fix brightness hotkeys on a Clevo laptop. CADL is not used anywhere in the driver code at the moment, but it could be used in BIOS as is the case with the Clevo laptop. The Clevo B7130 requires the CADL field to contain at least the ID of the LCD device. If this field is empty, the ACPI methods that are called on pressing brightness / display switching hotkeys will not trigger a notification. As a result, it appears as no hotkey has been pressed. Reference: https://bugs.freedesktop.org/show_bug.cgi?id=45452Tested-by:
Peter Wu <lekensteyn@gmail.com> Signed-off-by:
Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch>
-
Daniel Vetter authored
See bspec, Vol3 Part2, Section 1.1.3 "Display Mode Set Sequence". This applies to all platforms where we currently support eDP on, i.e. ilk, snb & ivb. Without this change we fail to light up the eDP port on previously unused crtcs (likely because something is stuck on the old pipe), and we also fail to properly disable the old pipe (i.e. bit 30 in the PIPECONF register is stuck as set until the next reboot). v2: Rebased on top of the edp panel off sequence changes in 3.6-rc2. Reviewed-by:
Paulo Zanoni <paulo.r.zanoni@intel.com> Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=44001Signed-Off-by:
-
Daniel Vetter authored
These have been added because dp links are fiddle things and don't like it when we try to re-train an enabled output (or disable a disabled output harder). And because the crtc helper code is ridiculously bad add tracking the modeset state. But with the new code in place it is simply a bug to disable a disabled encoder or to enable an enabled encoder again. Hence convert these to WARNs (and bail out for safety), but flatten all conditionals in the code itself. Reviewed-by:
-
Daniel Vetter authored
With the previous patch to clean up where exactly these two functions are getting called, this patch can tackle the enable/disable code itself: - WARN if the port enable bit is in the wrong state or if the edp pll bit is in the wrong state, just for paranoia's sake. - Don't disable the edp pll harder in the modeset functions just for fun. - Don't set the edp pll enable flag in intel_dp->DP in modeset, do that while changing the actual hw state. We do the same with the actual port enable bit, so this is a bit more consistent. - Track the current DP register value when setting things up and add some comments how intel_dp->DP is used in the disable code. v2: Be more careful with resetting intel_dp->DP - otherwise dpms off->on will fail spectacularly, becuase we enable the eDP port when we should only enable the eDP pll. Reviewed-by:
-
Daniel Vetter authored
By using the new pre_enable/post_disable functions. To ensure that we only frob the cpu edp pll while the pipe is off add the relevant asserts. Thanks to the new output state staging, this is now really easy. With this fixed we can now finally rip out the special-case handling in the dp dpms code and replace it by the common intel_connector_dpms. Reviewed-by:
-
Daniel Vetter authored
The cpu eDP encoder has some horrible hacks to set up the DP pll at the right time. To be able to move them to the right place, add some more encoder callbacks so that this can happen at the right time. LVDS has some similar funky hacks, but that would require more work (we need to move around the pll setup a bit). Hence for now only wire these new callbacks up for ilk+ - we only have cpu eDP on these platforms. v2: Bikeshed the vtable ordering, requested by Chris Wilson. Reviewed-by:
-
Daniel Vetter authored
It's bogus. If I've followed the history of this piece of code correctly, i.e. the initial register write with the following vblank wait, this goes all the way back to the original enabling of DP support in commit a4fc5ed6 Author: Keith Packard <keithp@keithp.com> Date: Tue Apr 7 16:16:42 2009 -0700 drm/i915: Add Display Port support Unfortunately it seems to be nothing more than glorified duct-tape and sometimes actively harmful. Adam Jackson noticed this for CPT platforms with commit e8519464 Author: Adam Jackson <ajax@redhat.com> Date: Thu Jul 21 17:48:38 2011 -0400 drm/i915/dp: Don't turn CPT DP ports on too early Unfortunately this kept the code around for ilk and gm45. The specific failure case I'm seeing here is that after a dpms off/on cycle we have the bits from the last link training (hopefully successful link training) set in intel_dp->DP. This is requiered so that complete_link_train can enable the port with the right tuning values. Unfortunately writing these again to the disabled port at dpms on time kills the port somehow until it's disabled - dp link training fails in an endless loop without this patch on my mobile ilk and gm45. Cc: Chris Wilson <chris@chris-wilson.co.uk> Tested-by:
Chris Wilson <chris@chris-wilson.co.uk> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=51493Signed-Off-by:
-
Ben Widawsky authored
With the new "standardized" sysfs interfaces we need to be a bit more careful about setting the RPS values. Because the sysfs code and the rps workqueue can run at the same time, if the sysfs setter wins the race to the mutex, the workqueue can come in and set a value which is out of range (ie. we're no longer protecting by RPINTLIM). I was not able to actually make this error occur in testing. Signed-off-by:
Ben Widawsky <ben@bwidawsk.net> Reviewed-by:
-
Ben Widawsky authored
In order to keep our cached values in sync with the hardware, we need a posting read here. CC: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by:
-
Ben Widawsky authored
Userspace applications such as PowerTOP are interesting in being able to read the current GPU frequency. The patch itself sets up a generic array for gen6 attributes so we can easily add other items in the future (and it also happens to be just about the cleanest way to do this). The patch is a nice addition to commit 1ac02185dff3afac146d745ba220dc6672d1d162 Author: Daniel Vetter <daniel.vetter@ffwll.ch> Date: Thu Aug 30 13:26:48 2012 +0200 drm/i915: add a tracepoint for gpu frequency changes Reading the GPU frequncy can be done by reading a file like: /sys/class/drm/card0/render_frequency_mhz Reviewed-by: -
Ben Widawsky authored
Magic numbers are bad mmmkay. In this case in particular the value is especially weird because the docs say multiple things. We'll need this value for sysfs, so extracting it is useful for that as well. Reviewed-by:
-
Ben Widawsky authored
Name variables a bit better for copy-pasters. This got turned up as part of review for upcoming sysfs patches. Reviewed-by:
-
Paulo Zanoni authored
Signed-off-by:
-
Paulo Zanoni authored
Because declaring a variable in the beginning of the function, then initializing it 100 lines later, then using it 100 lines later does not make our code look good IMHO. Signed-off-by:
-
Paulo Zanoni authored
Because ironlake_crtc_mode_set is a giant function that used to have 404 lines. Let's try to make it less complex/confusing. Signed-off-by:
-
Chris Wilson authored
Rather than have multiple data structures for describing our page layout in conjunction with the array of pages, we can migrate all users over to a scatterlist. One major advantage, other than unifying the page tracking structures, this offers is that we replace the vmalloc'ed array (which can be up to a megabyte in size) with a chain of individual pages which helps reduce memory pressure. The disadvantage is that we then do not have a simple array to iterate, or to access randomly. The common case for this is in the relocation processing, which will typically fit within a single scatterlist page and so be almost the same cost as the simple array. For iterating over the array, the extra function call could be optimised away, but in reality is an insignificant cost of either binding the pages, or performing the pwrite/pread. v2: Fix drm_clflush_sg() to not invoke wbinvd as well! And fix the trivial compile error from rebasing. Signed-off-by:
-
Chris Wilson authored
By using the recently introduced pinning of pages, we can safely drop the mutex in the knowledge that the pages are not going to disappear beneath us, and so we can simplify the code for iterating over the pages. Signed-off-by:
-
Chris Wilson authored
By using the recently introduced pinning of pages, we can safely drop the mutex in the knowledge that the pages are not going to disappear jeneath us, and so we can simplify the code for iterating over the pages. Note: The old code had such complicated page refcounting since it used obj->pages as a micro-optimization if it's there, but that could (before this patch) disappear when we drop the dev->struct_mutex. Hence some manual page refcounting was required for the slow path, complicated by the fact that pages returned by shmem_read_mapping_page already have a pageref, which needs to be dropped again. Signed-off-by:
-
Chris Wilson authored
We need to refcount our pages in order to prevent reaping them at inopportune times, such as when they currently vmapped or exported to another driver. However, we also wish to keep the lazy deallocation of our pages so we need to take a pin/unpinned approach rather than a simple refcount. Signed-off-by:
-
Chris Wilson authored
In order to specialise functions depending upon the type of object, we can attach vfuncs to each object via a new ->ops pointer. For instance, this will be used in future patches to only bind pages from a dma-buf for the duration that the object is used by the GPU - and so prevent them from pinning those pages for the entire of the object. v2: Bonus comments. Signed-off-by:
-
Ben Widawsky authored
There are internal patches for a feature which require a parameter to query whether support exists . These patches cannot be made external yet. In order to keep existing tests and userspace happy and free from conflicts, reserve a number for it. Signed-off-by:
-
- 19 Sep, 2012 3 commits
-
-
git://people.freedesktop.org/~danvet/drm-intelDave Airlie authored
Daniel writes: "The big ticket item here is the new i915 modeset infrastructure. Shockingly it didn't not blow up all over the place (i.e. I've managed to fix the ugly issues before merging). 1-2 smaller corner cases broke, but we have patches. Also, there's tons of patches on top of this that clean out cruft and fix a few bugs that couldn't be fixed with the crtc helper based stuff. So more stuff to come ;-) Also a few other things: - Tiny fix in the fb helper to go through the official dpms interface instead of calling the crtc helper code. - forcewake code frobbery from Ben, code should be more in-line with what Windows does now. - fixes for the render ring flush on hsw (Paulo) - gpu frequency tracepoint - vlv forcewake changes to better align it with our understanding of the forcewake magic. - a few smaller cleanups" + 2 fixes. * 'for-airlied' of git://people.freedesktop.org/~danvet/drm-intel: (78 commits) drm/i915: fix OOPS in lid_notify drm/i915: correctly update crtc->x/y in set_base drm/fb helper: don't call drm_helper_connector_dpms directly drm/i915: improve modeset state checking after dpms calls drm/i915: add tons of modeset state checks drm/i915: no longer call drm_helper_resume_force_mode drm/i915: disable all crtcs at suspend time drm/i915: push commit_output_state past the crtc/encoder preparing drm/i915: switch the load detect code to the staged modeset config drm/i915: WARN if the pipe won't turn off drm/i915: s/intel_encoder_disable/intel_encoder_noop drm/i915: push commit_output_state past crtc disabling drm/i915: implement new set_mode code flow drm/i915: compute masks of crtcs affected in set_mode drm/i915: use staged outuput config in lvds->mode_fixup drm/i915: use staged outuput config in tv->mode_fixup drm/i915: extract adjusted mode computation drm/i915: move output commit and crtc disabling into set_mode drm/i915: remove crtc disabling special case drm/i915: push crtc->fb update into pipe_set_base ...
-
Dave Airlie authored
We hit this a lot with i915 and although we'd like to engineer things to hit it a lot less, this commit at least makes it consume a few less cycles. from something containing movzwl 0x0(%rip),%r10d to add %r8,%rdx I only noticed it while using perf to profile something else. Reviewed-by:
Dave Airlie <airlied@redhat.com>
-
git://linuxtv.org/pinchartl/fbdevDave Airlie authored
Laurent writes: The SH Mobile DRM driver is now (in my opinion) ready for mainline. It requires GEM and KMS/FB helpers that have been reviewed on the list and tested. Sascha is waiting for them to reach your tree to send a pull request for another new driver. * 'drm-lcdc' of git://linuxtv.org/pinchartl/fbdev: drm: Renesas SH Mobile DRM driver drm: Add NV24 and NV42 pixel formats DRM: Add DRM KMS/FB CMA helper DRM: Add DRM GEM CMA helper drm/edid: limit printk when facing bad edid
-
- 18 Sep, 2012 4 commits
-
-
Laurent Pinchart authored
The SH Mobile LCD controller (LCDC) DRM driver supports the main graphics plane in RGB and YUV formats, as well as the overlay planes (in alpha-blending mode only). Only flat panel outputs using the parallel interface are supported. Support for SYS panels, HDMI and DSI is currently not implemented. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by:
Sascha Hauer <s.hauer@pengutronix.de>
-
Laurent Pinchart authored
Signed-off-by: -
Lars-Peter Clausen authored
This patchset introduces a set of helper function for implementing the KMS framebuffer layer for drivers which use the DRM GEM CMA helper function. Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Tested-by:
-
Sascha Hauer authored
Many embedded drm devices do not have a IOMMU and no dedicated memory for graphics. These devices use CMA (Contiguous Memory Allocator) backed graphics memory. This patch provides helper functions to be able to share the code. The code technically does not depend on CMA as the backend allocator, the name has been chosen because CMA makes for a nice, short but still descriptive function prefix. Signed-off-by:
-
- 17 Sep, 2012 3 commits
-
-
Daniel Vetter authored
This goes back to commit c1c7af60 Author: Jesse Barnes <jbarnes@virtuousgeek.org> Date: Thu Sep 10 15:28:03 2009 -0700 drm/i915: force mode set at lid open time It was used to fix an issue on a i915GM based Thinkpad X41, which somehow clobbered the modeset state at lid close time. Since then massive amounts of things changed: Tons of fixes to the modeset sequence, OpRegion support, better integration with the acpi code. Especially OpRegion /should/ allow us to control the display hw cooperatively with the firmware, without the firmware clobbering the hw state behind our backs. So it's dubious whether we still need this. The second issue is that it's unclear who's responsibility it actually is to restore the mode - Chris Wilson suggests to just emit a hotplug event and let userspace figure things out. The real reason I've stumbled over this is that the new modeset code breaks drm_helper_resume_force_mode - it OOPSes derefing a NULL vfunc pointer. The reason this wasn't caught in testing earlier is that in commit c9354c85 Author: Linus Torvalds <torvalds@linux-foundation.org> Date: Mon Nov 2 09:29:55 2009 -0800 i915: fix intel graphics suspend breakage due to resume/lid event confusion logic was added to _not_ restore the modeset state after a resume. And since most machines are configured to auto-suspend on lid-close, this neatly papered over the issue. Summarizing, this shouldn't be required on any platform supporting OpRegion. And none of the really old machines I have here seem to require it either. Hence I'm inclined to just rip it out. But in case that there are really firmwares out there that clobber the hw state, replace it with a call to intel_modset_check_state. This will ensure that we catch any issues as soon as they happen. Cc: Chris Wilson <chris@chris-wilson.co.uk> Acked-by:
-
Daniel Vetter authored
While reworking the modeset sequence, this got lost in commit 25c5b266 Author: Daniel Vetter <daniel.vetter@ffwll.ch> Date: Sun Jul 8 22:08:04 2012 +0200 drm/i915: implement new set_mode code flow I've noticed this because some Xorg versions seem to set up a new mode with every crtc at (0,0) and then pan to the right multi-monitor setup. And since some hacks of mine added more calls to mode_set using the stored crtc->x/y my multi-screen setup blew up. Reviewed-by:
-
Jerome Glisse authored
Limit printing bad edid information at one time per connector. Connector that are connected to a bad monitor/kvm will likely stay connected to the same bad monitor/kvm and it makes no sense to keep printing the bad edid message. Signed-off-by:
Jerome Glisse <jglisse@redhat.com> Reviewed-by:
Adam Jackson <ajax@redhat.com> Signed-off-by:
-
- 13 Sep, 2012 9 commits
-
-
Emil Goode authored
This patch removes a unused struct psb_intel_connector Sparse gives a warning: drivers/gpu/drm/gma500/cdv_intel_hdmi.c:142:30: warning: unused variable ‘psb_intel_connector’ [-Wunused-variable] Signed-off-by:
Emil Goode <emilgoode@gmail.com> Signed-off-by:
-
Wei Yongjun authored
The memory return by kzalloc() or kmem_cache_zalloc() has already be set to zero, so remove useless memset(0). Signed-off-by:
Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by:
-
Shirish S authored
The current logic for probing ddc is limited to 2 blocks (256 bytes), this patch adds support for the 4 block (512) data. To do this, a single 8-bit segment index is passed to the display via the I2C address 30h. Data from the selected segment is then immediately read via the regular DDC2 address using a repeated I2C 'START' signal. Signed-off-by:
Shirish S <s.shirish@samsung.com> Reviewed-by:
Jean Delvare <jdelvare@suse.de> Reviewed-by:
Ville Syrjala <ville.syrjala@linux.intel.com> Signed-off-by:
-
Robert P. J. Day authored
Since arch/arm/include/asm/pgtable.h contains: #define io_remap_pfn_range(vma,from,pfn,size,prot) \ remap_pfn_range(vma, from, pfn, size, prot) there is no point treating ARM as a special case in distinguishing between remap_pfn_range() and io_remap_pfn_range(). Signed-off-by:Robert P. J. Day <rpjday@crashcourse.ca> Signed-off-by:
-
Andy Shevchenko authored
Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Ville Syrjälä authored
There are two slightly different pieces of code for HDMI VSDB detection. Unify the code into a single helper function. Also fix a bug where drm_detect_hdmi_monitor() would stop looking for the HDMI VSDB after the first vendor specific block is found, whether or not that block happened to be the HDMI VSDB. The standard allows for any number of vendor specific blocks to be present. Signed-off-by:
-
Ville Syrjälä authored
The length of HDMI VSDB must be at least 5 bytes. Other than the minimum, nothing else about the length is specified. Check the length before accessing any additional field beyond the minimum length. Signed-off-by:
-
Ville Syrjälä authored
Make sure drm_detect_hdmi_monitor() and drm_detect_monitor_audio() don't access beyond the extension block. Signed-off-by:
-
Russell King - ARM Linux authored
At the moment, there is an inconsistency in the way modes are named. Modes with timings parsed from the EDID information will call drm_mode_set_name(), which will name the mode using this form: <horizontal-res>x<vertical-res><interlace-char> eg, 1920x1080i for an interlaced mode, or 1920x1080 for a progressive mode. However, timings parsed using the tables in drm_edid_modes.h do not have the 'i' suffix. You are left to deduce that they're interlaced from xrandr's output by the lower vertical refresh frequencies. This patch changes the interlaced mode names in drm_edid_modes.h to follow the style set by drm_mode_set_name(), which makes it clear in xrandr which modes are interlaced and which are not (as xrandr groups the refresh rates on a line according to the name field.) Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Reviewed-by:
Alex Deucher <alexander.deucher@amd.com> Reviewed-by:
-
