into ppc970.osdl.org:/home/torvalds/v2.5/linux

kNFSd needs it.

into kernel.bkbits.net:/home/davem/net-2.6

into nuts.davemloft.net:/disk1/BK/net-2.6

into ppc970.osdl.org:/home/torvalds/v2.5/linux

of redundancy, and to help prevent future errors.

This makes GregKH happy by removing the device name from the
device.bus_id field (and replacing it with a "name" sysfs attribute).

It also renames the parent device from "vdevice" to "vio", making the
/sys/bus and /sys/devices hierarchies consistent.

into ppc970.osdl.org:/home/torvalds/v2.5/linux

Add documentation for the above two functions.  Allow a NULL name to
be passed to amba_request_regions.  In this case, we use the driver's
name associated with the device.

This allows the decompressor to automatically detect the geometry of
the cache while booting to ensure correct behaviour over a wider
number of ARM CPUs.

This optimises the underlying string-long read function for little
endian platforms.

This gives greater information on the cause of the bad IRQ, allowing
the cause to be more effectively traced.

The old sysctl PM interface has been replaced by the driver models
interface.  This has been gone for a while in the -rmk tree and no
one complained, so there's no point keeping it around.

- use dev_dbg for device-centric debugging messages
- use pr_debug for general debugging messages
- use dmapools instead of pcipools
- use NULL rather than 0 for NULL pointers
- use enum dma_data_direction rather than int
- use DMA_* direction definitions rather than PCI_DMA_*
- only check for sane DMA direction on mapping functions, but
  check that DMA direction matches when unmapping/syncing.

Thanks to Adrian Bunk.

Remove kernel 2.0 #ifdef's from arm code, and move MODULE_* to
the end of the file.  Add an appropriate MODULE_LICENSE().

Currently, sinit_max_init_timeo is treated as the maximum timeout
value for INIT retransmissions and the INIT process is aborted when
the timeout reaches this value. But as per the SCTP sockets API draft,
sinit_max_init_timeo only limits the timeout. The INIT process should
be aborted only after MAX_INIT_RETRANSMITS.

Add an iseries defconfig and update the pseries one.

CONFIG_VETH isnt used anymore so we lets get rid of it.

Fix a compile error in the ppc64 pci hotplug code.

ppc64 tlb flush rework from Paul Mackerras

Instead of doing a double pass of the pagetables, we batch things
up in the pte flush routines and then shoot the batch down in
flush_tlb_pending.

Our page aging was broken, we never flushed entries out of the ppc64
hashtable. We now flush in ptep_test_and_clear_young.

A number of other things were fixed up in the process:

- change ppc64_tlb_batch to per cpu data
- remove some LPAR debug code
- be more careful with ioremap_mm inits
- clean up arch/ppc64/mm/init.c, create tlb.c

Set the ks bit on userspace segments otherwise the kernel can read/write
into userspace mprotected pages.

This allows us to use more than 2Gb of RAM on a PowerMac G5.  You can
also boot with iommu=off to disable it, but then you get back the 2Gb
RAM limitation.

Make IDE advertise only 128 entries of SG table on archs with an IOMMU.

The current IOMMU implementations of pci_map_sg() may produce segments
that don't match the boundary requirements of IDE, thus causing the
driver to break them up.  The BIO is supposed to account for that,
however, it cannot account for a pci_map_sg producing a segment of the
requested size, but with incorrect alignement, thus we may still try to
break up the list in more entries than is supported by the HW.

A similar fix already went in libata.  The "real" long term fix will be
to move the boundary requirements to struct device so that pci_map_sg()
can respect them when producing the sglist.  In the meantime, this
band-aid works around the problem.

Lots of things renamed, sillicaps killed, stuffs moved around and common
code properly extracted from implementation specific code, new
allocator, etc...  The code is overall a lot simpler, faster, less prone
to fail, and a lot more manageable.  I didn't use "bk mv", there is no
need to keep the old history attached to the new file.

This adds a hack to /dev/mem (along with the other ones already there)
to prevent mapping cacheable of the IO hole.

Without this, XFree blows up on machines with enough memory to go past
the IO hole.  It also tries to prevent memory from beeing mapped
uncached.  Cache paradoxes are evil and can kill the CPU.

The necessary page_is_ram() call was added by the previous patch doing
the proper IO hole accounting.

On machines with an IO hole (like Apple G5 with more than 2Gb of RAM,
but also some pSeries) we failed to properly account for the real
amount of physical RAM and inform the zone allocator of our hole size.

During the process, I included Anton slaughtering of the guard page we
had in the first 256Mb kernel segment, thus allowing this segment to be
mapped with large pages as it should be.

This removes the unused common_regs_m6 and add one more register to be
cleared, according to latest XFree code from ATI.

Fix a stupid warning in PowerMac SMP build on ppc64

Fix the build.

Pass me a brown paper bag.

into ppc970.osdl.org:/home/torvalds/v2.5/linux

into ppc970.osdl.org:/home/torvalds/v2.5/linux

And also make a note in ata_piix.c so this is not forgotten
in the future.