tg3 uses GSO as workaround if the hardware cannot perform TSO on certain
packets.  We should not modify the ip header fields if we do GSO on the
packet.  It happens to work by accident because GSO recalculates the IP
checksum and IP total length.

Also fix the tg3_start_xmit comment to reflect that this is the only
xmit function for all devices.
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Lorenzo Colitti says:

====================
Make mark-based routing work better with multiple separate networks.

Mark-based routing (ip rule fwmark 17 lookup 100) combined with
either iptables marking (iptables -j MARK --set-mark 17) or
application-based marking (the SO_MARK setsockopt) are a good
way to deal with connecting simultaneously to multiple networks.

Each network can be given a routing table, and ip rules can
be configured to make different fwmarks select different
networks. Applications can select networks them by setting
appropriate socket marks, and iptables rules can be used to
handle non-aware applications, enforce policy, etc.

This patch series improves functionality when mark-based routing
is used in this way. Current behaviour has the following
limitations:

1. Kernel-originated replies that are not associated with a
   socket always use a mark of zero. This means that, for
   example, when the kernel sends a ping reply or a TCP reset,
   it does not send it on the network from which it received the
   original packet.
2. Path MTU discovery, which is triggered by incoming packets,
   does not always work correctly, because the routing lookups it
   uses to clone routes do not take the fwmark into account and
   thus can happen in the wrong routing table.
3. Application-based marking works well for outbound connections,
   but does not work well for incoming connections. Marking a
   listening socket causes that socket to only accept
   connections from a given network, and sockets that are
   returned by accept() are not marked (and are thus not routed
   correctly).

sysctl. This causes route lookups for kernel-generated replies
and PMTUD to use the fwmark of the packet that caused them.

which causes TCP sockets returned by accept() to be marked with
the same mark that sent the intial SYN packet.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When using mark-based routing, sockets returned from accept()
may need to be marked differently depending on the incoming
connection request.

This is the case, for example, if different socket marks identify
different networks: a listening socket may want to accept
connections from all networks, but each connection should be
marked with the network that the request came in on, so that
subsequent packets are sent on the correct network.

This patch adds a sysctl to mark TCP sockets based on the fwmark
of the incoming SYN packet. If enabled, and an unmarked socket
receives a SYN, then the SYN packet's fwmark is written to the
connection's inet_request_sock, and later written back to the
accepted socket when the connection is established.  If the
socket already has a nonzero mark, then the behaviour is the same
as it is today, i.e., the listening socket's fwmark is used.

Black-box tested using user-mode linux:

- IPv4/IPv6 SYN+ACK, FIN, etc. packets are routed based on the
  mark of the incoming SYN packet.
- The socket returned by accept() is marked with the mark of the
  incoming SYN packet.
- Tested with syncookies=1 and syncookies=2.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, routing lookups used for Path PMTU Discovery in
absence of a socket or on unmarked sockets use a mark of 0.
This causes PMTUD not to work when using routing based on
netfilter fwmark mangling and fwmark ip rules, such as:

  iptables -j MARK --set-mark 17
  ip rule add fwmark 17 lookup 100

This patch causes these route lookups to use the fwmark from the
received ICMP error when the fwmark_reflect sysctl is enabled.
This allows the administrator to make PMTUD work by configuring
appropriate fwmark rules to mark the inbound ICMP packets.

Black-box tested using user-mode linux by pointing different
fwmarks at routing tables egressing on different interfaces, and
using iptables mangling to mark packets inbound on each interface
with the interface's fwmark. ICMPv4 and ICMPv6 PMTU discovery
work as expected when mark reflection is enabled and fail when
it is disabled.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kernel-originated IP packets that have no user socket associated
with them (e.g., ICMP errors and echo replies, TCP RSTs, etc.)
are emitted with a mark of zero. Add a sysctl to make them have
the same mark as the packet they are replying to.

This allows an administrator that wishes to do so to use
mark-based routing, firewalling, etc. for these replies by
marking the original packets inbound.

Tested using user-mode linux:
 - ICMP/ICMPv6 echo replies and errors.
 - TCP RST packets (IPv4 and IPv6).
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Beniamino Galvani says:

====================
arc_emac: promiscuous/multicast mode and netpoll support

These patches add support for promiscuous mode, multicast filtering
and netpoll to the ARC EMAC driver.

They were both tested on a Radxa Rock board which uses a ARC EMAC IP
core integrated in the Rockchip RK3188 SoC.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch implements the set_rx_mode function to enable/disable
promiscuous or all-multicast modes and to update the multicast
filtering list of the device.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuchung Cheng says:

====================
tcp: IPv6 support for fastopen server

This patch series add IPv6 support for fastopen server. To minimize
code duplication in IPv4 and IPv6, the current v4 only code is
refactored and common code is moved into net/ipv4/tcp_fastopen.c.

Also the current code uses a different function from
tcp_v4_send_synack() to send the first SYN-ACK in fastopen.
The new code eliminates this separate function by refactoring the
child-socket and syn-ack creation code.  After these refactoring
in the first four patches, we can easily add the fastopen code in
IPv6 by changing corresponding IPv6 functions.

Note Fast Open client already supports IPv6. This patch is for
the server-side (passive open) IPv6 support only.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

After all the preparatory works, supporting IPv6 in Fast Open is now easy.
We pretty much just mirror v4 code. The only difference is how we
generate the Fast Open cookie for IPv6 sockets. Since Fast Open cookie
is 128 bits and we use AES 128, we use CBC-MAC to encrypt both the
source and destination IPv6 addresses since the cookie is a MAC tag.
Signed-off-by: Daniel Lee <longinus00@gmail.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Jerry Chu <hkchu@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If a fast open socket is already accepted by the user, it should
be treated like a connected socket to record the ICMP error in
sk_softerr, so the user can fetch it. Do that in both tcp_v4_err
and tcp_v6_err.

Also refactor the sequence window check to improve readability
(e.g., there were two local variables named 'req').
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Daniel Lee <longinus00@gmail.com>
Signed-off-by: Jerry Chu <hkchu@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To avoid large code duplication in IPv6, we need to first simplify
the complicate SYN-ACK sending code in tcp_v4_conn_request().

To use tcp_v4(6)_send_synack() to send all SYN-ACKs, we need to
initialize the mini socket's receive window before trying to
create the child socket and/or building the SYN-ACK packet. So we move
that initialization from tcp_make_synack() to tcp_v4_conn_request()
as a new function tcp_openreq_init_req_rwin().

After this refactoring the SYN-ACK sending code is simpler and easier
to implement Fast Open for IPv6.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Daniel Lee <longinus00@gmail.com>
Signed-off-by: Jerry Chu <hkchu@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Consolidate various cookie checking and generation code to simplify
the fast open processing. The main goal is to reduce code duplication
in tcp_v4_conn_request() for IPv6 support.

Removes two experimental sysctl flags TFO_SERVER_ALWAYS and
TFO_SERVER_COOKIE_NOT_CHKD used primarily for developmental debugging
purposes.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Daniel Lee <longinus00@gmail.com>
Signed-off-by: Jerry Chu <hkchu@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move common TFO functions that will be used by both v4 and v6
to tcp_fastopen.c. Create a helper tcp_fastopen_queue_check().
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Daniel Lee <longinus00@gmail.com>
Signed-off-by: Jerry Chu <hkchu@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bjørn Mork says:

====================
cdc_mbim: cleanups and new features

This series depends on commit 6b5eeb7f ("net: cdc_mbim: handle
unaccelerated VLAN tagged frames"), which is currently in "net" but
not yet in "net-next".

Patch 4 might have a minor context collision with the "cdc_ncm: add
buffer tuning and stats using ethtool" series I just posted for
review.  Please let me know if I should submit an adjusted version
in either direction.  These two series' are otherwise completely
independent of each other.

The major new feature here is in patch 1, which I hope will solve
some problems with the original design without changing the existing
API, optionally allowing IP session 0 to be treated like any other
MBIM session.

The rest are some minor cleanups and finally some documentation of
the current driver APIs, after this series has been applied.  I
started feeling a bit more mortal than usual lately, which probably
is healthy, and realized that I should put some of the stuff in my
head in a somewhat less volatile storage.

v2:

Fixed patch 1 so that it actually does what it claims to do. This time
it is even tested for functionality, and not just build tested...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The NCM class match in the cdc_mbim driver is confusing and
cause unexpected behaviour. The USB core guarantees that a
USB interface is in altsetting 0 when probing starts. This
means that devices implementing a NCM 1.0 backwards
compatible MBIM function (a "NCM/MBIM function") always hit
the NCM entry in the cdc_mbim driver match table. Such
functions will never match any of the MBIM entries.

This causes unexpeced behaviour for cases where the NCM and
MBIM entries are differet, which is currently the case for
all except Ericsson devices.

Improve the probing of NCM/MBIM functions by looking up the
device again in the cdc_mbim match table after switching to
the MBIM identity.

The shared altsetting selection is updated to better
accommodate the new probing logic, returning the preferred
altsetting for the control interface instead of the data
interface. The control interface altsetting update is moved
to the cdc_mbim driver. It is never necessary to change the
control interface altsetting for NCM.

Cc: Greg Suarez <gsuarez@smithmicro.com>
Reported by: Yu-an Shih <yshih@nvidia.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

An initial attempt on describing some of the odd APIs
provided by this driver.

Cc: Greg Suarez <gsuarez@smithmicro.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

DSS VLANs are pseudo network interfaces representing arbitrary
data streams, and specifically not IP. Preventing spurious IP
packets can sometimes be a hassle. The kernel will for example
send an IPv6 Router Solicit when the interface is brought up
unless the user has been careful enough to disable IPv6 first.
Such packets forwared to a MBIM DSS session will look like
spurious noise to the device, and can cause it to log an error
or even malfunction.

Drop all IP packets on the designated DSS VLANs to prevent such
unwanted spurious transmissions.

Cc: Greg Suarez <gsuarez@smithmicro.com>
Reported-by: Arnaud Desmier <adesmier@sequans.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

The cdc_mbim driver maps 802.1q VLANs to MBIM IP and DSS
sessions. MBIM IP session 0 is handled as an exception and
is mapped to untagged frames.

This patch adds optional support for remapping MBIM IP
session 0 to 802.1q VLAN ID 4094 instead. The default
behaviour is not changed. The new behaviour is triggered
by adding a link for this previously unsupported VLAN.

The untagged mapping was chosen initially to support the
assumed most common use case: Most current MBIM devices only
support a single IP session (i.e. session 0 only), and using
untagged frames lets the users completely ignore the
additonal complexity of the multiplexing layer.

But when the multiplexing features of MBIM are used, then
this netdev gets a double meaning: It becomes the master
interface for all the VLAN subdevs the additional sessions
are mapped to, while still serving as the untagged IP
interface for session 0.

This can be problematic, especially when using Device Service
Streams (DSS), as have become apparent recently with the
availability of devices with real DSS support. Some use cases
need to e.g set a MTU which is higher than allowed for IP
Session 0. The dual role also leads to the situation where
the IP Session 0 interface cannot be taken down without
breaking unrelated IP or DSS sessions - a devastating side
effect which applications managing a simple IP session cannot
be expected to be aware of. A typical DHCP client will assume
that it should bring the interface down after releasing the
IP lease.

These problems can be avoided by tagging IP session 0 packets
too, making this session similar to all other multiplexed
sessions. This redefines the main netdev as an upper master
interface only.

Cc: Greg Suarez <gsuarez@smithmicro.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: get rid of SET_ETHTOOL_OPS

Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.

Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
-       SET_ETHTOOL_OPS(dev, ops);
+       dev->ethtool_ops = ops;

Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sk_unattached_filter_create() will copy the filter's instructions so we
don't need to have the master copy hanging around after initialization.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix build when CONFIG_NET is not enabled.
Fixes these build errors:

WARNING: "sk_unattached_filter_destroy" [lib/test_bpf.ko] undefined!
WARNING: "kfree_skb" [lib/test_bpf.ko] undefined!
WARNING: "sk_unattached_filter_create" [lib/test_bpf.ko] undefined!
WARNING: "sk_run_filter_int_skb" [lib/test_bpf.ko] undefined!
WARNING: "__alloc_skb" [lib/test_bpf.ko] undefined!
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Do not collide with the x86-64 PTRACE user API namespace.

net/core/filter.c:57:0: warning: "R8" redefined [enabled by default]
arch/x86/include/uapi/asm/ptrace-abi.h:38:0: note: this is the location of the previous definition

Fix by adding a BPF_ prefix to the register macros.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix build when BNX2X_SRIOV is not enabled.
Change one parameter struct from bnx2 to bnx2x and don't return a value
from a void function.

drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.h:576:48: warning: 'struct bnx2' declared inside parameter list [enabled by default]
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.h:576:48: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]

drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.h:576:60: warning: 'return' with a value, in function returning void [enabled by default]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc:	Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mugunthan V N says:

====================
Add DRA7xx and AM43xx platform support in cpsw-phy-sel driver

Adding DRA7xx and AM43xx platform support to cpsw-phy-sel driver to select
phy mode in control driver and fixing the uninitialized dev by initializing
to platform device structure pointer.

Changes from Initial version
* Added back the missing patch (1/3)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

AM43xx phy mode selection is similar to AM33xx platform, so adding only
the compatibility string to the driver
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add dra7xx support for selecting the phy mode which is present in control
module of dra7xx SoC
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

priv->dev is uninitialized, initializing with pdev->dev
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When I use the following command, eth0 cannot send any packets.
 #tc qdisc add dev eth0 root handle 1: hhf limit 1

Because qlen need be smaller than limit, all packets were dropped.
Fix this by qlen *<=* limit.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The __vlan_find_dev_deep should always called in RCU, according
David's suggestion, rename to __vlan_find_dev_deep_rcu looks more
reasonable.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As suggested by several people, rename local_df to ignore_df,
since it means "ignore df bit if it is set".

Cc: Maciej Żenczykowski <maze@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/ethernet/altera/altera_sgdma.c
	net/netlink/af_netlink.c
	net/sched/cls_api.c
	net/sched/sch_api.c

The netlink conflict dealt with moving to netlink_capable() and
netlink_ns_capable() in the 'net' tree vs. supporting 'tc' operations
in non-init namespaces.  These were simple transformations from
netlink_capable to netlink_ns_capable.

The Altera driver conflict was simply code removal overlapping some
void pointer cast cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>

Hariprasad Shenai says:

====================
Misc. fixes for cxgb4 and cxgb4vf driver

This series of patch provides fixes for cxgb4 and cxgb4vf driver related to
rx checksum counter and decodes module type a bit more for ethtool output.

The patches series is created against David Miller's 'net-next' tree.

We would like to request this patch series to get merged via David Miller's
'net-next' tree.

We have included all the maintainers of respective drivers. Kindly review the
change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

the parameter rt will be assigned to c.arg in function fib6_clean_tree(),
but function fib6_prune_clone() doesn't use c.arg, so we can remove it
safely.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change ensures the driver can be built successfully without the
CONFIG_SYSFS flag.
MS-TFS: 182270
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix kconfig warnings:

PTP_1588_CLOCK selects NET_PTP_CLASSIFY, which depends on NET,
so PTP_1588_CLOCK should also depend on NET.

PTP_1588_CLOCK_PCH selects PTP_1588_CLOCK so the former should
depend on NET.

warning: (IXP4XX_ETH && PTP_1588_CLOCK) selects NET_PTP_CLASSIFY which has unmet direct dependencies (NET)

warning: (SFC && TILE_NET && BFIN_MAC_USE_HWSTAMP && TIGON3 && FEC && E1000E && IGB && IXGBE && I40E && MLX4_EN && SXGBE_ETH && STMMAC_ETH && TI_CPTS && PTP_1588_CLOCK_GIANFAR && PTP_1588_CLOCK_IXP46X && DP83640_PHY && PTP_1588_CLOCK_PCH) selects PTP_1588_CLOCK which has unmet direct dependencies (NET)
[This warning is caused by the new 'depends on NET' in PTP_1588_CLOCK.]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexei Starovoitov says:

====================
BPF testsuite and cleanup

This patchset adds BPF testsuite and improves readability of classic
to internal BPF converter.

The testsuite helped to find 'negative offset bug' in x64 JIT that was
fixed by commit fdfaf64e ("x86: bpf_jit: support negative offsets")

It can be very useful for classic and internal JIT compiler developers.
Also it serves as performance benchmark.

x86_64/i386 pass all tests with and without JIT. arm32 JIT is failing
negative offset tests which are unsupported.

Internal BPF tests are much larger than classic tests to cover different
combinations of registers. Negative tests check correctness of classic
BPF verifier which must reject them.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>