To detect potential bugs in CAN protocol implementations (double removal of
receiver entries) a WARN() statement has been used if no matching list item was
found for removal.

The fault injection issued by syzkaller was able to create a situation where
the closing of a socket runs simultaneously to the notifier call chain for
removing the CAN network device in use.

This case is very unlikely in real life but it doesn't break anything.
Therefore we just replace the WARN() statement with pr_warn() to preserve the
notification for the CAN protocol development.

Reported-by: syzbot+381d06e0c8eaacb8706f@syzkaller.appspotmail.com
Reported-by: syzbot+d0ddd88c9a7432f041e6@syzkaller.appspotmail.com
Reported-by: syzbot+76d62d3b8162883c7d11@syzkaller.appspotmail.com
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201126192140.14350-1-socketcan@hartkopp.netSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Add support for mcan bit timing and control mode according to bosch mcan IP
version 3.3.0. The mcan version read from the Core Release field of CREL
register would be 33. Accordingly the properties are to be set for mcan v3.3.0
Signed-off-by: Pankaj Sharma <pankj.sharma@samsung.com>
Link: https://lore.kernel.org/r/1606366302-5520-1-git-send-email-pankj.sharma@samsung.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

At lest the revision 3.3.0 of the bosch m_can IP core specifies that valid
register values for "Nominal Time segment after sample point (NTSEG2)" are from
1 to 127. As the hardware uses a value of one more than the programmed value,
mean tseg2_min is 2.

This patch fixes the tseg2_min value accordingly.

Cc: Dan Murphy <dmurphy@ti.com>
Cc: Mario Huettel <mario.huettel@gmx.net>
Acked-by: Sriram Dash <sriram.dash@samsung.com>
Link: https://lore.kernel.org/r/20201124190751.3972238-1-mkl@pengutronix.de
Fixes: b03cfc5b ("can: m_can: Enable M_CAN version dependent initialization")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The threaded IRQ handler is used for the tcan4x5x driver only. The IRQ pin of
the tcan4x5x controller is active low, so better not use IRQF_TRIGGER_FALLING
when requesting the IRQ. As this can result in missing interrupts.

Further, if the device tree specified the interrupt as "IRQ_TYPE_LEVEL_LOW",
unloading and reloading of the driver results in the following error during
ifup:

| irq: type mismatch, failed to map hwirq-31 for gpio@20a8000!
| tcan4x5x spi1.1: m_can device registered (irq=0, version=32)
| tcan4x5x spi1.1 can2: TCAN4X5X successfully initialized.
| tcan4x5x spi1.1 can2: failed to request interrupt

This patch fixes the problem by removing the IRQF_TRIGGER_FALLING from the
request_threaded_irq().

Fixes: f524f829 ("can: m_can: Create a m_can platform framework")
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Sriram Dash <sriram.dash@samsung.com>
Cc: Pankaj Sharma <pankj.sharma@samsung.com>
Link: https://lore.kernel.org/r/20201127093548.509253-1-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch add a check to the mcp251xfd_probe() function to bail out and give
the user a proper error message if no IRQ is specified. Otherwise the driver
will probe just fine but ifup will fail with a meaningless "RTNETLINK answers:
Invalid argument" error message.

Link: https://lore.kernel.org/r/20201123113522.3820052-1-mkl@pengutronix.deReported-by: Niels Petter <petter@ka-long.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The firmware on the original USB2CAN by Geschwister Schneider Technologie
Entwicklungs- und Vertriebs UG exchanges all data between the host and the
device in host byte order. This is done with the struct
gs_host_config::byte_order member, which is sent first to indicate the desired
byte order.

The widely used open source firmware candleLight doesn't support this feature
and exchanges the data in little endian byte order. This breaks if a device
with candleLight firmware is used on big endianess systems.

To fix this problem, all u32 (but not the struct gs_host_frame::echo_id, which
is a transparent cookie) are converted to __le32.

Cc: Maximilian Schneider <max@schneidersoft.net>
Cc: Hubert Denkmair <hubert@denkmair.de>
Reported-by: Michael Rausch <mr@netadair.de>
Link: https://lore.kernel.org/r/b58aace7-61f3-6df7-c6df-69fee2c66906@netadair.deTested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Fixes: d08e973a ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/r/20201120103818.3386964-1-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Currently lock gets freed only if timeout expires, but missed a
case when HW returns failure and goes for cleanup.

Fixes: efca3878 ("ch_ktls: Issue if connection offload fails")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Link: https://lore.kernel.org/r/20201125072626.10861-1-rohitm@chelsio.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

tls_device_offload_cleanup_rx doesn't clear tls_ctx->netdev after
calling tls_dev_del if TLX TX offload is also enabled. Clearing
tls_ctx->netdev gets postponed until tls_device_gc_task. It leaves a
time frame when tls_device_down may get called and call tls_dev_del for
RX one extra time, confusing the driver, which may lead to a crash.

This patch corrects this racy behavior by adding a flag to prevent
tls_device_down from calling tls_dev_del the second time.

Fixes: e8f69799 ("net/tls: Add generic NIC offload infrastructure")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20201125221810.69870-1-saeedm@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Parav Pandit says:

====================
devlink port attribute fixes

This patchset contains 2 small fixes for devlink port attributes.

Patch summary:
Patch-1 synchronize the devlink port attribute reader
        with net namespace change operation
Patch-2 Ensure to return devlink port's netdevice attributes
        when netdev and devlink instance belong to same net namespace
====================

Link: https://lore.kernel.org/r/20201125091620.6781-1-parav@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When devlink reload operation is not used, netdev of an Ethernet port may
be present in different net namespace than the net namespace of the
devlink instance.

Ensure that both the devlink instance and devlink port netdev are located
in same net namespace.

Fixes: 070c63f2 ("net: devlink: allow to change namespaces during reload")
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

A netdevice of a devlink port can be moved to different net namespace
than its parent devlink instance.
This scenario occurs when devlink reload is not used.

When netdevice is undergoing migration to net namespace, its ifindex
and name may change.

In such use case, devlink port query may read stale netdev attributes.

Fix it by reading them under rtnl lock.

Fixes: bfcd3a46 ("Introduce devlink infrastructure")
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Feed kstrtou8 with NULL terminated string.

Changes since v1:
-Use sscanf to get rid of adhoc string parse.
Changes since v2:
-Check if sscanf returns 3.

Fixes: 7ea5fda2 ("ptp: ptp_clockmatrix: update to support 4.8.7 firmware")
Signed-off-by: Min Li <min.li.xe@renesas.com>
Link: https://lore.kernel.org/r/1606273115-25792-1-git-send-email-min.li.xe@renesas.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The tc-taprio base time indicates the beginning of the tc-taprio
schedule, which is cyclic by definition (where the length of the cycle
in nanoseconds is called the cycle time). The base time is a 64-bit PTP
time in the TAI domain.

Logically, the base-time should be a future time. But that imposes some
restrictions to user space, which has to retrieve the current PTP time
from the NIC first, then calculate a base time that will still be larger
than the base time by the time the kernel driver programs this value
into the hardware. Actually ensuring that the programmed base time is in
the future is still a problem even if the kernel alone deals with this.

Luckily, the enetc hardware already advances a base-time that is in the
past into a congruent time in the immediate future, according to the
same formula that can be found in the software implementation of taprio
(in taprio_get_start_time):

	/* Schedule the start time for the beginning of the next
	 * cycle.
	 */
	n = div64_s64(ktime_sub_ns(now, base), cycle);
	*start = ktime_add_ns(base, (n + 1) * cycle);

There's only one problem: the driver doesn't let the hardware do that.
It interferes with the base-time passed from user space, by special-casing
the situation when the base-time is zero, and replaces that with the
current PTP time. This changes the intended effective base-time of the
schedule, which will in the end have a different phase offset than if
the base-time of 0.000000000 was to be advanced by an integer multiple
of the cycle-time.

Fixes: 34c6adf1 ("enetc: Configure the Time-Aware Scheduler via tc-taprio offload")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20201124220259.3027991-1-vladimir.oltean@nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

After cited commit, gro_cells_destroy() became damn slow
on hosts with a lot of cores.

This is because we have one additional synchronize_net() per cpu as
stated in the changelog.

gro_cells_init() is setting NAPI_STATE_NO_BUSY_POLL, and this was enough
to not have one synchronize_net() call per netif_napi_del()

We can factorize all the synchronize_net() to a single one,
right before freeing per-cpu memory.

Fixes: 5198d545 ("net: remove napi_hash_del() from driver-facing API")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20201124203822.1360107-1-eric.dumazet@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Commit 75792624 ("net: stmmac: add flexible PPS to dwmac
4.10a") was intended to modify the struct dwmac410_ops, but it got
somehow badly merged and modified the struct dwmac4_ops.

Revert the modification in struct dwmac4_ops and re-apply it
properly in struct dwmac410_ops.

Fixes: 75792624 ("net: stmmac: add flexible PPS to dwmac 4.10a")
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Reported-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20201124223729.886992-1-antonio.borneo@st.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

kmemleak report a memory leak as follows:

unreferenced object 0xffff8880059c6a00 (size 64):
  comm "ip", pid 23696, jiffies 4296590183 (age 1755.384s)
  hex dump (first 32 bytes):
    20 01 00 10 00 00 00 00 00 00 00 00 00 00 00 00   ...............
    1c 00 00 00 00 00 00 00 00 00 00 00 07 00 00 00  ................
  backtrace:
    [<00000000aa4e7a87>] ip6addrlbl_add+0x90/0xbb0
    [<0000000070b8d7f1>] ip6addrlbl_net_init+0x109/0x170
    [<000000006a9ca9d4>] ops_init+0xa8/0x3c0
    [<000000002da57bf2>] setup_net+0x2de/0x7e0
    [<000000004e52d573>] copy_net_ns+0x27d/0x530
    [<00000000b07ae2b4>] create_new_namespaces+0x382/0xa30
    [<000000003b76d36f>] unshare_nsproxy_namespaces+0xa1/0x1d0
    [<0000000030653721>] ksys_unshare+0x3a4/0x780
    [<0000000007e82e40>] __x64_sys_unshare+0x2d/0x40
    [<0000000031a10c08>] do_syscall_64+0x33/0x40
    [<0000000099df30e7>] entry_SYSCALL_64_after_hwframe+0x44/0xa9

We should free all rules when we catch an error in ip6addrlbl_net_init().
otherwise a memory leak will occur.

Fixes: 2a8cc6c8 ("[IPV6] ADDRCONF: Support RFC3484 configurable address selection policy table.")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Link: https://lore.kernel.org/r/20201124071728.8385-1-wanghai38@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Make an explicit suggestion how to post user space side of kernel
patches to avoid reposts when patchwork groups the wrong patches.

v2: mention the cases unlike iproute2 explicitly
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Wunderlich says:

====================
Here is a batman-adv bugfix:

 - set module owner to THIS_MODULE, by Taehee Yoo

* tag 'batadv-net-pullrequest-20201124' of git://git.open-mesh.org/linux-merge:
  batman-adv: set .owner to THIS_MODULE
====================

Link: https://lore.kernel.org/r/20201124134417.17269-1-sw@simonwunderlich.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Lijun Pan says:

====================
ibmvnic: null pointer dereference

Fix two NULL pointer dereference crash issues.
Improve module removal procedure.
====================

Link: https://lore.kernel.org/r/20201123193547.57225-1-ljp@linux.ibm.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Based on the discussion with Sukadev Bhattiprolu and Dany Madden,
we believe that checking adapter->resetting bit is preferred
since RESETTING state flag is not as strict as resetting bit.
RESETTING state flag is removed since it is verbose now.

Fixes: 7d7195a0 ("ibmvnic: Do not process device remove during device reset")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

crq->msgs could be NULL if the previous reset did not complete after
freeing crq->msgs. Check for NULL before dereferencing them.

Snippet of call trace:
...
ibmvnic 30000003 env3 (unregistering): Releasing sub-CRQ
ibmvnic 30000003 env3 (unregistering): Releasing CRQ
BUG: Kernel NULL pointer dereference on read at 0x00000000
Faulting instruction address: 0xc0000000000c1a30
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
Modules linked in: ibmvnic(E-) rpadlpar_io rpaphp xt_CHECKSUM xt_MASQUERADE xt_conntrack ipt_REJECT nf_reject_ipv4 nft_compat nft_counter nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nf_tables xsk_diag tcp_diag udp_diag tun raw_diag inet_diag unix_diag bridge af_packet_diag netlink_diag stp llc rfkill sunrpc pseries_rng xts vmx_crypto uio_pdrv_genirq uio binfmt_misc ip_tables xfs libcrc32c sd_mod t10_pi sg ibmvscsi ibmveth scsi_transport_srp dm_mirror dm_region_hash dm_log dm_mod [last unloaded: ibmvnic]
CPU: 20 PID: 8426 Comm: kworker/20:0 Tainted: G            E     5.10.0-rc1+ #12
Workqueue: events __ibmvnic_reset [ibmvnic]
NIP:  c0000000000c1a30 LR: c008000001b00c18 CTR: 0000000000000400
REGS: c00000000d05b7a0 TRAP: 0380   Tainted: G            E      (5.10.0-rc1+)
MSR:  800000000280b033 <SF,VEC,VSX,EE,FP,ME,IR,DR,RI,LE>  CR: 44002480  XER: 20040000
CFAR: c0000000000c19ec IRQMASK: 0
GPR00: 0000000000000400 c00000000d05ba30 c008000001b17c00 0000000000000000
GPR04: 0000000000000000 0000000000000000 0000000000000000 00000000000001e2
GPR08: 000000000001f400 ffffffffffffd950 0000000000000000 c008000001b0b280
GPR12: c0000000000c19c8 c00000001ec72e00 c00000000019a778 c00000002647b440
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000006 0000000000000001 0000000000000003 0000000000000002
GPR24: 0000000000001000 c008000001b0d570 0000000000000005 c00000007ab5d550
GPR28: c00000007ab5c000 c000000032fcf848 c00000007ab5cc00 c000000032fcf800
NIP [c0000000000c1a30] memset+0x68/0x104
LR [c008000001b00c18] ibmvnic_reset_crq+0x70/0x110 [ibmvnic]
Call Trace:
[c00000000d05ba30] [0000000000000800] 0x800 (unreliable)
[c00000000d05bab0] [c008000001b0a930] do_reset.isra.40+0x224/0x634 [ibmvnic]
[c00000000d05bb80] [c008000001b08574] __ibmvnic_reset+0x17c/0x3c0 [ibmvnic]
[c00000000d05bc50] [c00000000018d9ac] process_one_work+0x2cc/0x800
[c00000000d05bd20] [c00000000018df58] worker_thread+0x78/0x520
[c00000000d05bdb0] [c00000000019a934] kthread+0x1c4/0x1d0
[c00000000d05be20] [c00000000000d5d0] ret_from_kernel_thread+0x5c/0x6c

Fixes: 032c5e82 ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

adapter->tx_scrq and adapter->rx_scrq could be NULL if the previous reset
did not complete after freeing sub crqs. Check for NULL before
dereferencing them.

Snippet of call trace:
ibmvnic 30000006 env6: Releasing sub-CRQ
ibmvnic 30000006 env6: Releasing CRQ
...
ibmvnic 30000006 env6: Got Control IP offload Response
ibmvnic 30000006 env6: Re-setting tx_scrq[0]
BUG: Kernel NULL pointer dereference on read at 0x00000000
Faulting instruction address: 0xc008000003dea7cc
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
Modules linked in: rpadlpar_io rpaphp xt_CHECKSUM xt_MASQUERADE xt_conntrack ipt_REJECT nf_reject_ipv4 nft_compat nft_counter nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nf_tables xsk_diag tcp_diag udp_diag raw_diag inet_diag unix_diag af_packet_diag netlink_diag tun bridge stp llc rfkill sunrpc pseries_rng xts vmx_crypto uio_pdrv_genirq uio binfmt_misc ip_tables xfs libcrc32c sd_mod t10_pi sg ibmvscsi ibmvnic ibmveth scsi_transport_srp dm_mirror dm_region_hash dm_log dm_mod
CPU: 80 PID: 1856 Comm: kworker/80:2 Tainted: G        W         5.8.0+ #4
Workqueue: events __ibmvnic_reset [ibmvnic]
NIP:  c008000003dea7cc LR: c008000003dea7bc CTR: 0000000000000000
REGS: c0000007ef7db860 TRAP: 0380   Tainted: G        W          (5.8.0+)
MSR:  800000000280b033 <SF,VEC,VSX,EE,FP,ME,IR,DR,RI,LE>  CR: 28002422  XER: 0000000d
CFAR: c000000000bd9520 IRQMASK: 0
GPR00: c008000003dea7bc c0000007ef7dbaf0 c008000003df7400 c0000007fa26ec00
GPR04: c0000007fcd0d008 c0000007fcd96350 0000000000000027 c0000007fcd0d010
GPR08: 0000000000000023 0000000000000000 0000000000000000 0000000000000000
GPR12: 0000000000002000 c00000001ec18e00 c0000000001982f8 c0000007bad6e840
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000000 0000000000000000 0000000000000000 fffffffffffffef7
GPR24: 0000000000000402 c0000007fa26f3a8 0000000000000003 c00000016f8ec048
GPR28: 0000000000000000 0000000000000000 0000000000000000 c0000007fa26ec00
NIP [c008000003dea7cc] ibmvnic_reset_init+0x15c/0x258 [ibmvnic]
LR [c008000003dea7bc] ibmvnic_reset_init+0x14c/0x258 [ibmvnic]
Call Trace:
[c0000007ef7dbaf0] [c008000003dea7bc] ibmvnic_reset_init+0x14c/0x258 [ibmvnic] (unreliable)
[c0000007ef7dbb80] [c008000003de8860] __ibmvnic_reset+0x408/0x970 [ibmvnic]
[c0000007ef7dbc50] [c00000000018b7cc] process_one_work+0x2cc/0x800
[c0000007ef7dbd20] [c00000000018bd78] worker_thread+0x78/0x520
[c0000007ef7dbdb0] [c0000000001984c4] kthread+0x1d4/0x1e0
[c0000007ef7dbe20] [c00000000000cea8] ret_from_kernel_thread+0x5c/0x74

Fixes: 57a49436 ("ibmvnic: Reset sub-crqs during driver reset")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Shay Agroskin says:

====================
Fixes for ENA driver

- fix wrong data offset on machines that support rx offset
- work-around Intel iommu issue
- fix out of bound access when request id is wrong
====================

Link: https://lore.kernel.org/r/20201123190859.21298-1-shayagr@amazon.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This patch fixes two lines in which the rx_offset received by the device
wasn't taken into account:

- prefetch function:
	In our driver the copied data would reside in
	rx_info->page + rx_headroom + rx_offset

	so the prefetch function is changed accordingly.

- setting page_offset to zero for descriptors > 1:
	for every descriptor but the first, the rx_offset is zero. Hence
	the page_offset value should be set to rx_headroom.

	The previous implementation changed the value of rx_info after
	the descriptor was added to the SKB (essentially providing wrong
	page offset).

Fixes: 68f236df ("net: ena: add support for the rx offset feature")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The ENA driver uses the readless mechanism, which uses DMA, to find
out what the DMA mask is supposed to be.

If DMA is used without setting the dma_mask first, it causes the
Intel IOMMU driver to think that ENA is a 32-bit device and therefore
disables IOMMU passthrough permanently.

This patch sets the dma_mask to be ENA_MAX_PHYS_ADDR_SIZE_BITS=48
before readless initialization in
ena_device_init()->ena_com_mmio_reg_read_request_init(),
which is large enough to workaround the intel_iommu issue.

DMA mask is set again to the correct value after it's received from the
device after readless is initialized.

The patch also changes the driver to use dma_set_mask_and_coherent()
function instead of the two pci_set_dma_mask() and
pci_set_consistent_dma_mask() ones. Both methods achieve the same
effect.

Fixes: 1738cd3e ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Mike Cui <mikecui@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

After request id is checked in validate_rx_req_id() its value is still
used in the line
	rx_ring->free_ids[next_to_clean] =
					rx_ring->ena_bufs[i].req_id;
even if it was found to be out-of-bound for the array free_ids.

The patch moves the request id to an earlier stage in the napi routine and
makes sure its value isn't used if it's found out-of-bounds.

Fixes: 30623e1e ("net: ena: avoid memory access violation by validating req_id properly")
Signed-off-by: Ido Segev <idose@amazon.com>
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

GPIOs - as returned by of_get_named_gpio() and used by the gpiolib - are
signed integers, where negative number indicates error.  The return
value of of_get_named_gpio() should not be assigned to an unsigned int
because in case of !CONFIG_GPIOLIB such number would be a valid GPIO.

Fixes: c04c674f ("nfc: s3fwrn5: Add driver for Samsung S3FWRN5 NFC Chip")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201123162351.209100-1-krzk@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The dpaa2 driver depends on devlink, so it should select
NET_DEVLINK in order to fix compile errors, such as:

drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.o: in function `dpaa2_eth_rx_err':
dpaa2-eth.c:(.text+0x3cec): undefined reference to `devlink_trap_report'
drivers/net/ethernet/freescale/dpaa2/dpaa2-eth-devlink.o: in function `dpaa2_eth_dl_info_get':
dpaa2-eth-devlink.c:(.text+0x160): undefined reference to `devlink_info_driver_name_put'

Fixes: ceeb03ad ("dpaa2-eth: add basic devlink support")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20201123163553.1666476-1-ciorneiioana@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add some file F: matches that is related to page_pool.
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/r/160613894639.2826716.14635284017814375894.stgit@firesoulSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When a BPF program is used to select between a type of TCP congestion
control algorithm that uses either ECN or not there is a case where the
synack for the frame was coming up without the ECT0 bit set. A bit of
research found that this was due to the final socket being configured to
dctcp while the listener socket was staying in cubic.

To reproduce it all that is needed is to monitor TCP traffic while running
the sample bpf program "samples/bpf/tcp_cong_kern.c". What is observed,
assuming tcp_dctcp module is loaded or compiled in and the traffic matches
the rules in the sample file, is that for all frames with the exception of
the synack the ECT0 bit is set.

To address that it is necessary to make one additional call to
tcp_bpf_ca_needs_ecn using the request socket and then use the output of
that to set the ECT0 bit for the tos/tclass of the packet.

Fixes: 91b5b21c ("bpf: Add support for changing congestion control")
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Link: https://lore.kernel.org/r/160593039663.2604.1374502006916871573.stgit@localhost.localdomainSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Fix reload stats structure exposed to the user. Change stats structure
hierarchy to have the reload action as a parent of the stat entry and
then stat entry includes value per limit. This will also help to avoid
string concatenation on iproute2 output.

Reload stats structure before this fix:
"stats": {
    "reload": {
        "driver_reinit": 2,
        "fw_activate": 1,
        "fw_activate_no_reset": 0
     }
}

After this fix:
"stats": {
    "reload": {
        "driver_reinit": {
            "unspecified": 2
        },
        "fw_activate": {
            "unspecified": 1,
            "no_reset": 0
        }
}

Fixes: a254c264 ("devlink: Add reload stats")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/1606109785-25197-1-git-send-email-moshe@mellanox.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When performing IPv6 forwarding, there is an expectation that SKBs
will have some headroom. When forwarding a packet from the aquantia
driver, this does not always happen, triggering a kernel warning.

aq_ring.c has this code (edited slightly for brevity):

if (buff->is_eop && buff->len <= AQ_CFG_RX_FRAME_MAX - AQ_SKB_ALIGN) {
    skb = build_skb(aq_buf_vaddr(&buff->rxdata), AQ_CFG_RX_FRAME_MAX);
} else {
    skb = napi_alloc_skb(napi, AQ_CFG_RX_HDR_SIZE);

There is a significant difference between the SKB produced by these
2 code paths. When napi_alloc_skb creates an SKB, there is a certain
amount of headroom reserved. However, this is not done in the
build_skb codepath.

As the hardware buffer that build_skb is built around does not
handle the presence of the SKB header, this code path is being
removed and the napi_alloc_skb path will always be used. This code
path does have to copy the packet header into the SKB, but it adds
the packet data as a frag.

Fixes: 018423e9 ("net: ethernet: aquantia: Add ring support code")
Signed-off-by: Lincoln Ramsay <lincoln.ramsay@opengear.com>
Link: https://lore.kernel.org/r/MWHPR1001MB23184F3EAFA413E0D1910EC9E8FC0@MWHPR1001MB2318.namprd10.prod.outlook.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

In the patchset merged by commit b9fcf0a0
("Merge branch 'support-AF_PACKET-for-layer-3-devices'") L3 devices which
did not have header_ops were given one for the purpose of protocol parsing
on af_packet transmit path.

That change made af_packet receive path regard these devices as having a
visible L3 header and therefore aligned incoming skb->data to point to the
skb's mac_header. Some devices, such as ipip, xfrmi, and others, do not
reset their mac_header prior to ingress and therefore their incoming
packets became malformed.

Ideally these devices would reset their mac headers, or af_packet would be
able to rely on dev->hard_header_len being 0 for such cases, but it seems
this is not the case.

Fix by changing af_packet RX ll visibility criteria to include the
existence of a '.create()' header operation, which is used when creating
a device hard header - via dev_hard_header() - by upper layers, and does
not exist in these L3 devices.

As this predicate may be useful in other situations, add it as a common
dev_has_header() helper in netdevice.h.

Fixes: b9fcf0a0 ("Merge branch 'support-AF_PACKET-for-layer-3-devices'")
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Acked-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20201121062817.3178900-1-eyal.birger@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Prevent VFs from resetting when PF driver is being unloaded:
- introduce new pf state: __I40E_VF_RESETS_DISABLED;
- check if pf state has __I40E_VF_RESETS_DISABLED state set,
  if so, disable any further VFLR event notifications;
- when i40e_remove (rmmod i40e) is called, disable any resets on
  the VFs;

Previously if there were bare-metal VFs passing traffic and PF
driver was removed, there was a possibility of VFs triggering a Tx
timeout right before iavf_remove. This was causing iavf_close to
not be called because there is a check in the beginning of  iavf_remove
that bails out early if adapter->state < IAVF_DOWN_PENDING. This
makes it so some resources do not get cleaned up.

Fixes: 6a9ddb36 ("i40e: disable IOV before freeing resources")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20201120180640.3654474-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Starting from commit 8692cefc ("virtio_vsock: Fix race condition
in virtio_transport_recv_pkt"), we discard packets in
virtio_transport_recv_pkt() if the socket has been released.

When the socket is connected, we schedule a delayed work to wait the
RST packet from the other peer, also if SHUTDOWN_MASK is set in
sk->sk_shutdown.
This is done to complete the virtio-vsock shutdown algorithm, releasing
the port assigned to the socket definitively only when the other peer
has consumed all the packets.

If we discard the RST packet received, the socket will be closed only
when the VSOCK_CLOSE_TIMEOUT is reached.

Sergio discovered the issue while running ab(1) HTTP benchmark using
libkrun [1] and observing a latency increase with that commit.

To avoid this issue, we discard packet only if the socket is really
closed (SOCK_DONE flag is set).
We also set SOCK_DONE in virtio_transport_release() when we don't need
to wait any packets from the other peer (we didn't schedule the delayed
work). In this case we remove the socket from the vsock lists, releasing
the port assigned.

[1] https://github.com/containers/libkrun

Fixes: 8692cefc ("virtio_vsock: Fix race condition in virtio_transport_recv_pkt")
Cc: justin.he@arm.com
Reported-by: Sergio Lopez <slp@redhat.com>
Tested-by: Sergio Lopez <slp@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Jia He <justin.he@arm.com>
Link: https://lore.kernel.org/r/20201120104736.73749-1-sgarzare@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When the TCP stack is in SYN flood mode, the server child socket is
created from the SYN cookie received in a TCP packet with the ACK flag
set.

The child socket is created when the server receives the first TCP
packet with a valid SYN cookie from the client. Usually, this packet
corresponds to the final step of the TCP 3-way handshake, the ACK
packet. But is also possible to receive a valid SYN cookie from the
first TCP data packet sent by the client, and thus create a child socket
from that SYN cookie.

Since a client socket is ready to send data as soon as it receives the
SYN+ACK packet from the server, the client can send the ACK packet (sent
by the TCP stack code), and the first data packet (sent by the userspace
program) almost at the same time, and thus the server will equally
receive the two TCP packets with valid SYN cookies almost at the same
instant.

When such event happens, the TCP stack code has a race condition that
occurs between the momement a lookup is done to the established
connections hashtable to check for the existence of a connection for the
same client, and the moment that the child socket is added to the
established connections hashtable. As a consequence, this race condition
can lead to a situation where we add two child sockets to the
established connections hashtable and deliver two sockets to the
userspace program to the same client.

This patch fixes the race condition by checking if an existing child
socket exists for the same client when we are adding the second child
socket to the established connections socket. If an existing child
socket exists, we drop the packet and discard the second child socket
to the same client.
Signed-off-by: Ricardo Dias <rdias@singlestore.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20201120111133.GA67501@rdias-suse-pc.lanSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'wireless-drivers-2020-11-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for v5.10

First set of fixes for v5.10. One fix for iwlwifi kernel panic, others
less notable.

rtw88

* fix a bogus test found by clang

iwlwifi

* fix long memory reads causing soft lockup warnings

* fix kernel panic during Channel Switch Announcement (CSA)

* other smaller fixes

MAINTAINERS

* email address updates

* tag 'wireless-drivers-2020-11-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers:
  iwlwifi: mvm: fix kernel panic in case of assert during CSA
  iwlwifi: pcie: set LTR to avoid completion timeout
  iwlwifi: mvm: write queue_sync_state only for sync
  iwlwifi: mvm: properly cancel a session protection for P2P
  iwlwifi: mvm: use the HOT_SPOT_CMD to cancel an AUX ROC
  iwlwifi: sta: set max HE max A-MPDU according to HE capa
  MAINTAINERS: update maintainers list for Cypress
  MAINTAINERS: update Yan-Hsuan's email address
  iwlwifi: pcie: limit memory read spin time
  rtw88: fix fw_fifo_addr check
====================

Link: https://lore.kernel.org/r/20201123161037.C11D1C43460@smtp.codeaurora.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Lijun Pan says:

====================
ibmvnic: fixes in reset path

Patch 1/3 and 2/3 notify peers in failover and migration reset.
Patch 3/3 skips timeout reset if it is already resetting.
====================

Link: https://lore.kernel.org/r/20201120224013.46891-1-ljp@linux.ibm.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Sometimes it takes longer than 5 seconds (watchdog timeout) to complete
failover, migration, and other resets. In stead of scheduling another
timeout reset, we wait for the current one to complete.
Suggested-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Commit 61d3e1d9 ("ibmvnic: Remove netdev notify for failover resets")
excluded the failover case for notify call because it said
netdev_notify_peers() can cause network traffic to stall or halt.
Current testing does not show network traffic stall
or halt because of the notify call for failover event.
netdev_notify_peers may be used when a device wants to inform the
rest of the network about some sort of a reconfiguration
such as failover or migration.

It is unnecessary to call that in other events like
FATAL, NON_FATAL, CHANGE_PARAM, and TIMEOUT resets
since in those scenarios the hardware does not change.
If the driver must do a hard reset, it is necessary to notify peers.

Fixes: 61d3e1d9 ("ibmvnic: Remove netdev notify for failover resets")
Suggested-by: Brian King <brking@linux.vnet.ibm.com>
Suggested-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>