Pull Char / Misc driver fixes from Greg Kroah-Hartman:
 "Here are some small misc and w1 driver fixes for 3.6-rc3.  Nothing
  major, just some some bugfixes and a new device id for a w1 driver.

  Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"

* tag 'char-misc-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  1-Wire: Add support for the maxim ds1825 temperature sensor
  ti-st: Fix check for pdata->chip_awake function pointer
  mei: add mei_quirk_probe function
  mei: fix device stall after wd is stopped

Pull USB patches from Greg Kroah-Hartman:
 "Here are a number of small USB patches for 3.6-rc3.

  The "large" one is just a number of device id updates to the option
  driver, done by the manufacturer, properly fixing up the device ids
  based on shipping devices.

  Other than that, some gadget driver fixes, the obligitary XHCI
  patches, and some other device ids and bugs fixed.

  Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"

* tag 'usb-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
  USB: qcserial: fix port handling on Gobi 1K and 2K+
  USB: serial: Fix mos7840 timeout
  USB: option: add ZTE K5006-Z
  usb: gadget: u_ether: fix kworker 100% CPU issue with still used interfaces in eth_stop
  usb: host: tegra: fix warning messages in ehci_remove
  usb: host: mips: sead3: Update for EHCI register structure.
  usb: renesas_usbhs: fixup resume method for autonomy mode
  usb: renesas_usbhs: mod_host: add missing .bus_suspend/resume
  update MAINTAINERS for Oliver Neukum
  usb: usb_wwan: resume/suspend can be called after port is gone
  usb: serial: prevent suspend/resume from racing against probe/remove
  usb: usb_wwan: replace release and disconnect with a port_remove hook
  usb: serial: mos7840: Fixup mos7840_chars_in_buffer()
  USB: isp1362-hcd.c: usb message always saved in case of underrun
  OMAP: USB : Fix the EHCI enumeration and core retention issue
  usb: chipidea: fix and improve dependencies if usb host or gadget support is built as module
  USB: support the new interfaces of Huawei Data Card devices in option driver
  USB: ftdi_sio: Add VID/PID for Kondo Serial USB
  xhci: Switch PPT ports to EHCI on shutdown.
  xhci: Fix bug after deq ptr set to link TRB.
  ...

Fix fatal error in scripts/kernel-doc by ignoring the "__weak" attribute:

  Error(drivers/pci/pci.c:2820): cannot understand prototype: 'char * __weak pcibios_setup(char *str) '
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull a Yama bugfix from James Morris.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  Yama: access task_struct->comm directly

Pull C6X atomic64 support from Mark Salter:
 "Enable atomic64 ops in C6X
   - define L1_CACHE_SHIFT
   - select GENERIC_ATOMIC64"

* tag 'for-linus' of git://linux-c6x.org/git/projects/linux-c6x-upstreaming:
  C6X: select GENERIC_ATOMIC64
  C6X: add Lx_CACHE_SHIFT defines

Pull ext4 bug fixes from Ted Ts'o:
 "The following are all bug fixes and regressions.  The most notable are
  the ones which cause problems for ext4 on RAID --- a performance
  problem when mounting very large filesystems, and a kernel OOPS when
  doing an rm -rf on large directory hierarchies on fast devices."

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix kernel BUG on large-scale rm -rf commands
  ext4: fix long mount times on very big file systems
  ext4: don't call ext4_error while block group is locked
  ext4: avoid kmemcheck complaint from reading uninitialized memory
  ext4: make sure the journal sb is written in ext4_clear_journal_err()

In some cases when an autofs indirect mount is contained in a file
system that is marked as shared (such as when systemd does the
equivalent of "mount --make-rshared /" early in the boot), mounts
stop expiring.

When this happens the first expiry check on a mountpoint dentry in
autofs_expire_indirect() sees a mountpoint dentry with a higher
than minimal reference count. Consequently the dentry is condidered
busy and the actual expiry check is never done.

This particular check was originally meant as an optimisation to
detect a path walk in progress but with the addition of rcu-walk
it can be ineffective anyway.

Removing the test allows automounts to expire again since the
actual expire check doesn't rely on the dentry reference count.
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 968dee77: "ext4: fix hole punch failure when depth is greater
than 0" introduced a regression in v3.5.1/v3.6-rc1 which caused kernel
crashes when users ran run "rm -rf" on large directory hierarchy on
ext4 filesystems on RAID devices:

    BUG: unable to handle kernel NULL pointer dereference at 0000000000000028

    Process rm (pid: 18229, threadinfo ffff8801276bc000, task ffff880123631710)
    Call Trace:
     [<ffffffff81236483>] ? __ext4_handle_dirty_metadata+0x83/0x110
     [<ffffffff812353d3>] ext4_ext_truncate+0x193/0x1d0
     [<ffffffff8120a8cf>] ? ext4_mark_inode_dirty+0x7f/0x1f0
     [<ffffffff81207e05>] ext4_truncate+0xf5/0x100
     [<ffffffff8120cd51>] ext4_evict_inode+0x461/0x490
     [<ffffffff811a1312>] evict+0xa2/0x1a0
     [<ffffffff811a1513>] iput+0x103/0x1f0
     [<ffffffff81196d84>] do_unlinkat+0x154/0x1c0
     [<ffffffff8118cc3a>] ? sys_newfstatat+0x2a/0x40
     [<ffffffff81197b0b>] sys_unlinkat+0x1b/0x50
     [<ffffffff816135e9>] system_call_fastpath+0x16/0x1b
    Code: 8b 4d 20 0f b7 41 02 48 8d 04 40 48 8d 04 81 49 89 45 18 0f b7 49 02 48 83 c1 01 49 89 4d 00 e9 ae f8 ff ff 0f 1f 00 49 8b 45 28 <48> 8b 40 28 49 89 45 20 e9 85 f8 ff ff 0f 1f 80 00 00 00

    RIP  [<ffffffff81233164>] ext4_ext_remove_space+0xa34/0xdf0

This could be reproduced as follows:

The problem in commit 968dee77 was that caused the variable 'i' to
be left uninitialized if the truncate required more space than was
available in the journal.  This resulted in the function
ext4_ext_truncate_extend_restart() returning -EAGAIN, which caused
ext4_ext_remove_space() to restart the truncate operation after
starting a new jbd2 handle.
Reported-by: Maciej Żenczykowski <maze@google.com>
Reported-by: Marti Raudsepp <marti@juffo.org>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@vger.kernel.org

Commit 8aeb00ff: "ext4: fix overhead calculation used by
ext4_statfs()" introduced a O(n**2) calculation which makes very large
file systems take forever to mount.  Fix this with an optimization for
non-bigalloc file systems.  (For bigalloc file systems the overhead
needs to be set in the the superblock.)
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@vger.kernel.org

While in ext4_validate_block_bitmap(), if an block allocation bitmap
is found to be invalid, we call ext4_error() while the block group is
still locked.  This causes ext4_commit_super() to call a function
which might sleep while in an atomic context.

There's no need to keep the block group locked at this point, so hoist
the ext4_error() call up to ext4_validate_block_bitmap() and release
the block group spinlock before calling ext4_error().

The reported stack trace can be found at:

	http://article.gmane.org/gmane.comp.file-systems.ext4/33731Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@vger.kernel.org

The core ptrace access checking routine holds a task lock, and when
reporting a failure, Yama takes a separate task lock. To avoid a
potential deadlock with two ptracers taking the opposite locks, do not
use get_task_comm() and just use ->comm directly since accuracy is not
important for the report.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Suggested-by: Oleg Nesterov <oleg@redhat.com>
CC: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>

This patch adds support for maxim ds1825 based 1-wire temperature sensors.
Signed-off-by: Raphael Assenat <raph@8d.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ll_device_want_to_wakeup(): Fix the NULL pointer check on pdata->chip_awake,
which is performed on the wrong function pointer
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Following a report of a crash during an automount expire I found that
the locking in fs/autofs4/expire.c:get_next_positive_subdir() was wrong.
Not only is the locking wrong but the function is more complex than it
needs to be.

The function is meant to calculate (and dget) the next entry in the list
of directories contained in the root of an autofs mount point (an autofs
indirect mount to be precise). The main problem was that the d_lock of
the owner of the list was not being taken when walking the list, which
lead to list corruption under load. The only other lock that needs to
be taken is against the next dentry candidate so it can be checked for
usability.
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull VFIO fix from Alex Williamson:
 "Just a trivial patch to include vfio.h in the installed headers so we
  can complete userspace integration into QEMU."

* tag 'vfio-for-v3.6-rc1' of git://github.com/awilliam/linux-vfio:
  vfio: Include vfio.h in installed headers

Pull fuse updates from Miklos Szeredi.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: verify all ioctl retry iov elements
  fuse: add missing INIT flag descriptions
  fuse: add missing INIT flags
  fuse: update attributes on aio_read
  fuse: invalidate inode mapping if mtime changes
  fuse: add FUSE_AUTO_INVAL_DATA init flag

Merge tag 'stable/for-linus-3.6-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen

Pull Xen fix from Konrad Rzeszutek Wilk:
 "Way back in v3.5 we added a mechanism to populate back pages that were
  released (they overlapped with MMIO regions), but neglected to reserve
  the proper amount of virtual space for extend_brk to work properly.

  Coincidentally some other commit aligned the _brk space to larger area
  so I didn't trigger this until it was run on a machine with more than
  2GB of MMIO space."

 * On machines with large MMIO/PCI E820 spaces we fail to boot b/c
   we failed to pre-allocate large enough virtual space for extend_brk.

* tag 'stable/for-linus-3.6-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xen/p2m: Reserve 8MB of _brk space for P2M leafs when populating back.

Pull SuperH fixes from Paul Mundt.

* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
  sh: intc: Handle domain association for sparseirq pre-allocated vectors.
  sh: sh7269: Fix LCD pinmux
  sh: dma: fix request_irq usage

Moved to djbw@fb.com

Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Dan Williams <djbw@fb.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When dumping "Code: " sections from an oops, the trapping instruction
%rip points to can be a string copy

  2b:*  f3 a5                   rep movsl %ds:(%rsi),%es:(%rdi)

and the line contain a bunch of ":".  Current "cut" selects only the and
the second field output looks funnily overlaid this:

  2b:*  f3 a5                   rep movsl %ds     <-- trapping instruction:(%rsi),%es:(%rdi

Fix this by selecting the remaining fields too.

Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-kbuild@vger.kernel.org
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull two slave-dmaengine fixes from Vinod Koul:
 "One fixes the correct use of clock API in imx driver and the other
  enables clock for tegra driver, which is used for other tegra driver
  conversion to dmanegine in -next."

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dma: tegra: enable/disable dma clock
  dma: imx-dma: Fix kernel crash due to missing clock conversion

Pull more drm fixes from Dave Airlie:
 "Just some intel and nouveau ones this time, intel has more edp panel
  fixes for macbooks and nouveau has a suspend/resume regression fix in
  there."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/i915: Apply post-sync write for pipe control invalidates
  drm/i915: reorder edp disabling to fix ivb MacBook Air
  drm/nv86/fifo: suspend fix
  drm/nouveau: disable copy engine on NVAF
  nouveau: fixup scanout enable in nvc0_pm
  drm/nouveau/aux: mask off higher bits of auxch index in i2c table entry
  drm/nvd0/disp: mask off high 16 bit of negative cursor x-coordinate
  drm/i915: ensure i2c adapter is all set before adding it
  drm/i915: ignore eDP bpc settings from vbt
  drm/i915: Fix blank panel at reopening lid
  drm/nve0/fifo: add support for the flip completion swmthd

The main purpose of this function is to exclude ME devices
without support for MEI/HECI interface from binding

Currently affected systems are C600/X79 based servers
that expose PCI device even though it doesn't supported ME Interface.
MEI driver accessing such nonfunctional device can corrupt
the system.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Bjorn's latest patchset does break Gobi 1K and 2K because on both
devices as it claims usb interface 0.  That's because usbif 0 is not
handled in the switch statement, and thus the if0 gets claimed when it
should not.  So let's just make things even simpler yet, and handle both
the 1K and 2K+ cases separately.  This patch should not affect the new
Sierra device support, because those devices are matched via
interface-specific matching and thus should never hit the composite
code.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

After watchdog was disabled the driver would stall
due to wrong calculation of credits reduction

The cat&paste bug was introduced in the commit
7bdf72d3
mei: introduce mei_data2slots wrapper
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull two sparc fixes from David S. Miller.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: Be less verbose during vmemmap population.
  sparc64: do not clobber personality flags in sys_sparc64_personality()

* mos7840 driver was using multiple of HZ for the timeout handed off to
  usb_control_msg().  Changed the timeout to use msecs instead.

* Remove unused WAIT_FOR_EVER definition
Signed-off-by: Mark Ferrell <mferrell@uplogix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The ZTE (Vodafone) K5006-Z use the following
interface layout:

00 DIAG
01 secondary
02 modem
03 networkcard
04 storage

Ignoring interface #3 which is handled by the qmi_wwan
driver.

Cc: Thomas Schäfer <tschaefer@t-online.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The generic atomic64 support came in 2009 to support the perf subsystem
with the expectation that all architectures would implement atomic64
support. Since then, other optional parts of the generic kernel have
also come to expect atomic64 support. This patch enables generic atomic64
support for C6X architecture.
Signed-off-by: Mark Salter <msalter@redhat.com>

C6X currently lacks Lx_CACHE_SHIFT defines which are needed in a
few places in the generic kernel. This patch adds _SHIFT defines
for the various caches and bases the Lx_CACHE_BYTES defines on
them.
Signed-off-by: Mark Salter <msalter@redhat.com>

* 'drm-nouveau-fixes' of git://git.freedesktop.org/git/nouveau/linux-2.6:
  drm/nv86/fifo: suspend fix
  drm/nouveau: disable copy engine on NVAF
  nouveau: fixup scanout enable in nvc0_pm
  drm/nouveau/aux: mask off higher bits of auxch index in i2c table entry
  drm/nvd0/disp: mask off high 16 bit of negative cursor x-coordinate
  drm/nve0/fifo: add support for the flip completion swmthd

Daniel Vetter writes:

"A few important fixers:
- fix various lvds backlight issues, regressed in 3.6 (Takashi Iwai)
- make the retina mbp work (ignore bogus edp bpc value in vbt)
- fix a gmbus regression introduced in (iirc) 3.4 (Jani Nikula)
- fix an edp panel power sequence regression, fixes the new macbook air
- apply the tlb invalidate w/a

Otherwise we still have another gmbus regression (patches are awaiting
tested-bys) and there's something odd going with some rare systems not
entering rc6 often enough (and hence blowing through too much power).  It
seems to be a timing-related issue and can be mitigated by frobbing the
magic tuning parameters. We're still working on that one. Also, we still
have some fallout from the hw context support, but you can only hit that
with mesa master."

* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
  drm/i915: Apply post-sync write for pipe control invalidates
  drm/i915: reorder edp disabling to fix ivb MacBook Air
  drm/i915: ensure i2c adapter is all set before adding it
  drm/i915: ignore eDP bpc settings from vbt
  drm/i915: Fix blank panel at reopening lid

On a 2-node machine with 256GB of ram we get 512 lines of
console output, which is just too much.

This mimicks Yinghai Lu's x86 commit c2b91e2e
(x86_64/mm: check and print vmemmap allocation continuous) except that
we aren't ever going to get contiguous block pointers in between calls
so just print when the virtual address or node changes.

This decreases the output by an order of 16.

Also demote this to KERN_DEBUG.
Signed-off-by: David S. Miller <davem@davemloft.net>

When invalidating the TLBs it is documentated as requiring a post-sync
write. Failure to do so seems to result in a GPU hang.

Exposure to this hang on IVB seems to be a result of removing the extra
stalls required for SNB pipecontrol workarounds:

commit 6c6cf5aa
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Fri Jul 20 18:02:28 2012 +0100

    drm/i915: Only apply the SNB pipe control w/a to gen6

Note: Manually switch the pipe_control cmd to 4 dwords to avoid a
(silent) functional conflict with -next. This way will get a loud (but
conflict with next (since the scratch_addr has been deleted there).

Reported-and-tested-by: yex.tian@intel.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=53322Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: added note about merge conflict with -next.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

eDP is tons of fun. It turns out that at least the new MacBook Air 5,1
model absolutely doesn't like the new force vdd dance we've introduced
in

commit 6cb49835
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Sun May 20 17:14:50 2012 +0200

    drm/i915: enable vdd when switching off the eDP panel

But that patch also tried to fix some neat edp sequence issue with the
force_vdd timings. Closer inspection reveals that we've raised
force_vdd only to do the aux channel communication dp_sink_dpms. If we
move the edp_panel_off below that, we don't need any force_vdd for the
disable sequence, which makes the Air happy.

Unfortunately the reporter of the original bug that the above commit
fixed is travelling, so we can't test whether this regresses things.
But my theory is that since we don't check for any power-off ->
force_vdd-on delays in edp_panel_vdd_on, this was the actual
root-cause of this failure. With that force_vdd dance completely
eliminated, I'm hopeful the original bug stays fixed, too.

For reference the old bug, which hopefully doesn't get broken by this:

https://bugzilla.kernel.org/show_bug.cgi?id=43163

In any case, regression fixers win over plain bugfixes, so this needs
to go in asap.

v2: The crucial pieces seems to be to clear the force_vdd flag
uncoditionally, too, in edp_panel_off. Looks like this is left behind
by the firmware somehow.

v3: The Apple firmware seems to switch off the panel on it's own, hence
we still need to keep force_vdd on, but properly clear it when switching
the panel off.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=45671Tested-by: Roberto Romer <sildurin@gmail.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Tested-by: Keith Packard <keithp@keithp.com>
Cc: stable@vger.kernel.org
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Pull s390 patches from Martin Schwidefsky:
 "Included are bug fixes and a patch to enable system call filtering
  with BPF."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/compat: fix mmap compat system calls
  s390/compat: fix compat wrappers for process_vm system calls
  s390: do not clobber personality flags in sys_32_personality()
  s390/seccomp: add support for system call filtering using BPF
  s390/sclp_sdias: Add missing break and "fall through"
  s390/mm: remove MAX_PHYSADDR_BITS define

Pull drm fixes from Dave Airlie:
 "Radeon and intel fixes mostly, one fix to the mgag200 driver to not
  hang on certain server variants."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (32 commits)
  drm/radeon: fix typo in function header comment
  drm/radeon/kms: implement timestamp userspace query (v2)
  drm/radeon/kms: add MSAA texture support for r600-evergreen
  drm/radeon/kms: reorder code in r600_check_texture_resource
  drm/radeon: fence virtual address and free it once idle v4
  drm/radeon: fix some missing parens in asic macros
  drm/radeon: add some new SI pci ids
  drm/radeon: fix ordering in pll picking on dce4+
  drm/radeon: do not reenable crtc after moving vram start address
  drm/radeon: fix bank tiling parameters on cayman
  drm/radeon: fix bank tiling parameters on evergreen
  drm/radeon: fix bank tiling parameters on SI
  drm/radeon: properly handle crtc powergating
  drm/radeon: properly handle SS overrides on TN (v2)
  drm/radeon/dce4+: set a more reasonable cursor watermark
  drm/radeon: fix handling for ddc type 5 on combios
  drm/mgag200: fix G200ER pll picking algorithm
  drm/edid: Fix potential memory leak in edid_load()
  drm/udl: Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(.. [1]
  drm/radeon/kms: allow "invalid" DB formats as a means to disable DB
  ...

Commit 72121572 ("GPIO: gpio-pxa: fix devicetree functions") added an
"xlate" function pointer to the irq_domain_ops, but this function is nor
declared or defined anywhere when CONFIG_OF is disabled, causing the
build error:

  drivers/gpio/gpio-pxa.c:532:11: error: 'irq_domain_xlate_twocell' undeclared here (not in a function)

Extending the DT-only code section to cover the irq_domain_ops and the
pxa_gpio_dt_ids solves this problem and makes it clearer which code is
actually used without DT.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This fix is a backport from the reworked nouveau driver.  It masks off the
engines we're not expecting to use before attempting a channel kickoff.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>