add PSP RAP L0 check when RAP TA is loaded.
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

RAP TA is an optional firmware. if it doesn’t exist,
the driver should bypass psp_rap_invoke() function.

1. bypass psp_rap_invoke() when RAP TA is not loaded.
2. add new parameter (status) to query RAP TA status.
   (the status value is different with psp_ta_invoke(),
3. fix the 'rap_status' MThread critical problem.
   (used without lock)
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

add aldebaran serial number support.
(serial number from metrics table)
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

When there is no graphics support, KFD can use more of the VMIDs. Graphics
VMIDs are only used for video decoding/encoding and post processing. With
two VCE engines, there is no reason to reserve more than 2 VMIDs for that.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

SQ's watchdog timer monitors forward progress, a mask of which waves
caused the watchdog timeout is recorded into ras status registers and
then trigger a system fatal error event.

v2:
1. change *query_timeout_status to *query_sq_timeout_status.
2. move query_sq_timeout_status into amdgpu_ras_do_recovery.
3. add module parameters to enable/disable fatal error event and modify
the watchdog timer.

v3:
1. remove unused parameters of *enable_watchdog_timer
Signed-off-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The bank number of both VML2 and ATCL2 are changed to 8, so refine
related codes to avoid defining long name arrays.
Signed-off-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

add edc counter/status reset and query functions for gfx block of
aldebaran.

v2: change to clear edc counter explicitly
aldebaran hardware will not clear edc counter after driver reading them,
so driver should clear them explicitly.
Signed-off-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

add GC power brake feature support for Aldebaran.

v2: squash in fixes (Alex)
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The golden setting was changed recently. update to
the latest one
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

golden settings that should be applied
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Those registers should be programmed as one-time initialization
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Initialization of TRAP_DATA0/1 is still required for the debugger to detect
new waves on Aldebaran.  Also, per-vmid global trap enablement may be
required outside of debugger scope so move to init phase.

v2: just add the gfx 9.4.2 changes (Alex)
Signed-off-by: Jonathan Kim <Jonathan.Kim@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Create dedicated Aldebaran kfd2kgd callbacks to prepare
for new per-vmid register instructions for debug trap
setting functions and sending host traps.

v2: rebase (Alex)
Signed-off-by: Jonathan Kim <Jonathan.Kim@amd.com>
Reviewed-by: Oak Zeng <Oak.Zeng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

MEC firmware can silently fail the queue preemption request
without time out. In this case, HIQ's MQD's queue_doorbell_id
will be set. Check this field to see whether last queue preemption
was successful or not.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Suggested-by: Jay Cornwall <Jay.Cornwall@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This is to keep wavefront context for debug purpose
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Match existing asics.

v2: rebase (Alex)
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Le Ma <Le.Ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Aldebaran has fine grained DPM for GFXCLK. Instead of a discrete level,
user can specify a min/max range of GFXCLK for any profiling/tuning
purpose.This option is available only in manual performance level mode.
Select "manual" as power_dpm_force_performance_level and specify the
min/max range using pp_dpm_sclk sysfs node. User cannot specify a min/max
range outside of the default min/max range of the ASIC. If specified
outside the range, values will be bound by the default min/max range.

Ex: To use gfxclk min = 600MHz and max = 900MHz

echo manual > /sys/bus/pci/devices/.../power_dpm_force_performance_level
echo min 600 max 900 > /sys/bus/pci/devices/.../pp_dpm_sclk
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

the following message is not supported.

PPSMC_MSG_ReadSerialNumTop32
PPSMC_MSG_ReadSerialNumBottom32
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

With a recent gart page table re-construction, the gart page
table is now 2-level for some ASICs: PDB0->PTB.
In the case of 2-level gart page table, the page_table_base
of vmid0 should point to PDB0 instead of PTB.
Signed-off-by: Alex Sierra <alex.sierra@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Oak Zeng <Oak.Zeng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

More accurate words are used to address a
code review feedback
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

For the new 2-level GART table, the last PDE0 points
to PTB. Since PTB is in vram and right now we are
runing under s=0 mode (vram is treated as FB carveout),
so the s bit of this PDE0 should be set to 0.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

update mmhub client id table for Aldebaran.
Signed-off-by: Alex Sierra <alex.sierra@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Aldebaran can share the same initializing shader code witn
arcturus.
Signed-off-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

With the 2-level gart page table,  vram is squeezed into gart aperture
and FB aperture is disabled. Therefore all VRAM virtual addresses are
 in the GART aperture. However currently PSP requires TMR addresses
in FB aperture. So we need some design change at PSP FW level to support
this 2-level gart table driver change. Right now this PSP FW support
doesn't exist. To workaround this issue temporarily, FB aperture is
added back and the gart aperture address is converted back to FB aperture
for this PSP TMR address.

Will revert it after we get a fix from PSP FW.

v2: squash in tmr fix for other asics (Kevin)
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Set up HW for 2-level vmid0 page table: 1. Set up
PAGE_TABLE_START/END registers. Currently only plan
to do 2-level page table for ALDEBARAN, so only gfxhub1.0
and mmhub1.7 is changed. 2. Set page table base register.
For 2-level page table, the page table base should point
to PDB0. 3. Disable AGP and FB aperture as they are not
used.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Christian Konig <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

If use gart for FB translation, allocate and fill
PDB0.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Christian Konig <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add functions to allocate PDB0, map it for CPU access,
and fill it.

Those functions are only used for 2-level vmid0 page
table construction
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

If use gart for FB translation, we will squeeze vram into
sysvm aperture. This requires 2 level gart table. Add
page table depth and page table block size parameters
to gmc. This is prepare work to 2-level gart table
construction
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Christian Konig <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

If use GART for FB translation, place both vram and gart to sysvm
aperture. AGP aperture is not set up in this case because it
is not used
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Christian Konig <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Modify the comment to reflect the fact that, if
use GART for vram address translation for vmid0,
[vram_start, vram_end] will be placed inside SYSVM
aperture, together with GART.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Christian Konig <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

In amdgpu_gmc_gart_location function, gart_size is adjusted
by a smu_prv_buffer_size. This logic shouldn't belong to
this function. Move the logic to the mc_init functions
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Christian Konig <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

On A+A platform, CPU write page directory and page table in cached
mode. So it is necessary for page table walker to snoop CPU cache.
This setting is necessary for page walker to snoop page directory
and page table data out of CPU cache.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Acked-by: Christian Konig <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

On A+A platform, vram can be mapped as WB. Not necessarily
to always map vram as WC on such platform.

Calling function arch_io_reserve_memtype_wc will mark the
whole vram region as WC. So don't call it for A+A platform.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Suggested-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian Konig <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Status 0 indicates success, fix the check before using PPTable limit
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>`
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Performance Determinism is a new mode in Aldebaran where PMFW tries to
maintain sustained performance level. It can be enabled on a per-die
basis on aldebaran. To guarantee that it remains within the power cap,
a max GFX frequency needs to be specified in this mode. A new
power_dpm_force_performance_level, "perf_determinism", is defined to enable
this mode in amdgpu. The max frequency (in MHz) can be specified through
pp_dpm_sclk. The mode will be disabled once any other performance level
is chosen.

Ex: To enable perf determinism at 900Mhz max gfx clock

echo perf_determinism > /sys/bus/pci/devices/.../power_dpm_force_performance_level
echo max 900 > /sys/bus/pci/devices/.../pp_dpm_sclk
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

On aldebaran DCBTC should be run after enabling DPM. DCBTC won't be run
if support is not enabled in PPTable. Without PPTable support the message
is dummy and will return success always.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Aldebaran doesn't have AC/DC power limits. Separate the implementation
from SMU13. Max power limit is queried from PPTable.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The psp supplies the link type in the upper 2 bits of the psp xgmi node
information num_hops field.  With a new link type, Aldebaran has these
bits set to a non-zero value (1 = xGMI3) so the KFD topology will report
the incorrect IO link weights without proper masking.
The actual number of hops is located in the 3 least significant bits of
this field so mask if off accordingly before passing it to the KFD.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Reviewed-by: Amber Lin <amber.lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

By default this timestamp is 32 bit counter. It gets
overflowed in around 10 minutes.
Signed-off-by: Alex Sierra <alex.sierra@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

If xnack is on, VM retry fault interrupt send to IH ring1, and ring1
will be full quickly. IH cannot receive other interrupts, this causes
deadlock if migrating buffer using sdma and waiting for sdma done while
handling retry fault.

Remove VMC from IH storm client, enable ring1 write pointer overflow,
then IH will drop retry fault interrupts and be able to receive other
interrupts while driver is handling retry fault.

IH ring1 write pointer doesn't writeback to memory by IH, and ring1
write pointer recorded by self-irq is not updated, so always read
the latest ring1 write pointer from register.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>