Use generic DMA DT helper. Platforms booting with or without DT populated are
both supported.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

In PIO mode we can end up with the same errors as in DMA mode, but as IRQs
are disabled there we have to check for them manually after each command.

Also don't use the big controller reset hammer when receiving a NAK from a
slave. It's sufficient to tell the controller to continue at a clean state.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This commit fixes the three following races in PIO code:

- The CTRL0 register is racy in itself, when programming transfer state and
  run bit in the same cycle the hardware sometimes ends up using the state
  from the last transfer. Fix this by programming state in one cycle, make
  sure the write is flushed down APBX bus by reading back the reg and only
  then trigger the run bit.

- Only clear the DMAREQ bit in DEBUG0 after the read/write to the data reg
  happened. Otherwise we are racing with the hardware about who touches
  the data reg first.

- When checking for completion of a transfer it's not sufficient to check
  if the data engine finished, but also a check for i2c bus idle is needed.
  In PIO mode we are really fast to program the next transfer after a finished
  one, so the controller possibly tries to start a new transfer while the
  clkgen engine is still busy writing the NAK/STOP from the last transfer to
  the bus.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Using autosuspend helps to reduce the resume latency in situations where
another I2C message is going to be started soon. For example with HID over
I2C touch panels we get several messages in a short period of time while
the touch panel is in use.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This is not an atomic context so there is no need to use mdelay() but
instead use usleep_range().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The correct way to disable or enable the controller is to wait until the
DW_IC_ENABLE_STATUS register bit matches the bit we program into DW_IC_ENABLE
register. This procedure is described in the DesignWare I2C databook.

By doing this we can be sure that the controller is in correct state once
the function returns.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

It is not good idea to mix static and dynamic I2C adapter numbering. In
this particular case on Lynxpoint we had graphics I2C adapter which took
the first numbers preventing the designware I2C driver from using the
adapter numbers it preferred.

Since Lynxpoint support was just introduced and there is no hardware available
outside Intel we can fix this by switching to use dynamic adapter numbering
instead of static.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This makes the error handling much more simpler than open-coding everything
and in addition makes the probe function smaller an tidier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

With dev_err() we can get the device instance printed as well and is pretty
much standard to use dev_* macros in the drivers anyway. In addition
correct the indentation of probe() arguments.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This makes the error handling much more simpler than open-coding everything
and in addition makes the probe function smaller and tidier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

CONFIG_HOTPLUG is going away as an option, cleanup CONFIG_HOTPLUG
ifdefs in i2c files.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

SMBus read and write are supported by the emulation layer of i2c
framework if the controller doesn't have SMBus features.

I2C_M_RECV_LEN flag is used to let i2c drivers know rx length is not
yet determined but will be read to the first byte in rx buffer.

s3c2410 doesn't handle this flag. So only one byte is read from slave.
There fore following two features are added to the driver code.

1. skip rx length check if I2C_M_RECV_LEN is set and the length is 1.
2. add actual bytes to the rx length after reading first bytes if
   I2C_M_RECV_LEN.

I2C_M_RECV_LEN is only set for SMBus command. So this code does not
affect legacy codes which only use i2c command for s3c2410.
Signed-off-by: Jaemin Yoo <jmin.yoo@samsung.com>
Tested-by: Prasanna Kumar <prasanna.ps@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

i2c_del_mux_adapter always returns 0 and none of it current users check its
return value anyway. It is also an essential requirement of the Linux device
driver model, that functions which may be called from a device's remove callback
to free resources provided by the device, are not allowed to fail. This is the
case for i2c_del_mux_adapter(), so make its return type void to make the
fact that it won't fail explicit.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

i2c_del_mux_adapter() always returns 0. So all checks testing whether it will be
non zero will always evaluate to false and the conditional code is dead code.
This patch updates all callers of i2c_del_mux_adapter() to ignore its return
value and assume that it will always succeed (which it will). A subsequent
patch will make the return type of i2c_del_mux_adapter() void.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

i2c_del_adapter() is usually called from a drivers remove callback. The Linux
device driver model does not allow the remove callback to fail and all resources
allocated in the probe callback need to be freed, as well as all resources which
have been provided to the rest of the kernel(for example a I2C adapter) need to
be revoked. So any function revoking such resources isn't allowed to fail
either. i2c_del_adapter() adheres to this requirement and will never fail. But
i2c_del_adapter()'s return type is int, which may cause driver authors to think
that it can fail. This led to code constructs like:

	ret = i2c_del_adapter(...);
	BUG_ON(ret);

Since i2c_del_adapter() always returns 0 the BUG_ON is never hit and essentially
becomes dead code, which means it can be removed. Making the return type of
i2c_del_adapter() void makes it explicit that the function will never fail and
should prevent constructs like the above from re-appearing in the kernel code.

All callers of i2c_del_adapter() have already been updated in a previous patch
to ignore the return value, so the conversion of the return type from int to
void can be done without causing any build failures.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

i2c_del_adapter() always returns 0. So all checks testing whether it will be
non zero will always evaluate to false and the conditional code is dead code.
This patch updates all callers of i2c_del_mux_adapter() to ignore the return
value and assume that it will always succeed (which it will). In a subsequent
patch the return type of i2c_del_adapter() will be made void.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Currently i2c_del_adapter() returns -EINVAL when it gets an adapter which is not
registered. But none of the users of i2c_del_adapter() depend on this behavior,
so for the sake of being able to sanitize the return type of i2c_del_adapter
argue, that the purpose of i2c_del_adapter() is to remove an I2C adapter from
the system. If the adapter is not registered in the first place this becomes a
no-op. So we can return success without having to do anything.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The detach_adapter callback has been deprecated for quite some time and has no
user left. Keeping it alive blocks other cleanups, so remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This eliminates having an #ifdef returning NULL for the case
when OF is disabled.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Update the code to use devm_* API so that driver core will manage
resources.
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Since we have generic i2c bus recover routines now, these custom ones
need to be renamed to fix the namespace clash. Proper conversion needs
to be done by someone who has access to the hardware.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

gpio_direction_output() may fail, check for that and deal with it
appropriately. Also log an error message if gpio_request() fails.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

GPIOs may not be available immediately when i2c-gpio looks for them.
Implement support for deferred probing so that probing can be
attempted again later when GPIO pins are finally available.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Make them conform more to established standards.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The register definitions are only used in the driver itself.
This also removes the last dependency on plat/ includes from the
i2c driver.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

(SMATCH) drivers/i2c/busses/i2c-ismt.c:186:14: warning: duplicate const
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Tegra only supports, and always enables, device tree. Remove all ifdefs
and runtime checks for DT support from the driver. Platform data is
therefore no longer required. Delete the header that defines it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The commit: "i2c-core: dt: Pick i2c bus number from i2c alias if
present" adds support for automatically picking the bus number based
on the alias ID.  Remove the now unnecessary code from i2c-pxa that
did the same thing.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Add i2c bus recovery infrastructure to i2c adapters as specified in the i2c
protocol Rev. 03 section 3.1.16 titled "Bus clear".

http://www.nxp.com/documents/user_manual/UM10204.pdf

Sometimes during operation i2c bus hangs and we need to give dummy clocks to
slave device to start the transfer again. Now we may have capability in the bus
controller to generate these clocks or platform may have gpio pins which can be
toggled to generate dummy clocks. This patch supports both.

This patch also adds in generic bus recovery routines gpio or scl line based
which can be used by bus controller. In addition controller driver may provide
its own version of the bus recovery routine.

This doesn't support multi-master recovery for now.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[wsa: changed gpio type to int and minor reformatting]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This allows you to get the equivalent functionality of
i2c_add_numbered_adapter() with all data in the device tree and no
special case code in your driver.  This is a common device tree
technique.

For quick reference, the FDT syntax for using an alias to provide an
ID looks like:
  aliases {
    i2c0 = &i2c_0;
    i2c1 = &i2c_1;
  };
Signed-off-by: Doug Anderson <dianders@chromium.org>
[wsa: removed one check from static function. We know our callers]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Pull SCSI target fixes from Nicholas Bellinger:
 "These are mostly minor fixes this time around.  The iscsi-target CHAP
  big-endian bugfix and bump FD_MAX_SECTORS=2048 default patch to allow
  1MB sized I/Os for FILEIO backends on >= v3.5 code are both CC'ed to
  stable.

  Also, there is a persistent reservations regression that has recently
  been reported for >= v3.8.x code, that is currently being tracked down
  for v3.9."

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  target/pscsi: Reject cross page boundary case in pscsi_map_sg
  target/file: Bump FD_MAX_SECTORS to 2048 to handle 1M sized I/Os
  tcm_vhost: Flush vhost_work in vhost_scsi_flush()
  tcm_vhost: Add missed lock in vhost_scsi_clear_endpoint()
  target: fix possible memory leak in core_tpg_register()
  target/iscsi: Fix mutual CHAP auth on big-endian arches
  target_core_sbc: use noop for SYNCHRONIZE_CACHE

Pull md fixes from NeilBrown:
 "A few bugfixes for md

   - recent regressions in raid5
   - recent regressions in dmraid
   - a few instances of CONFIG_MULTICORE_RAID456 linger

  Several tagged for -stable"

* tag 'md-3.9-fixes' of git://neil.brown.name/md:
  md: remove CONFIG_MULTICORE_RAID456 entirely
  md/raid5: ensure sync and DISCARD don't happen at the same time.
  MD: Prevent sysfs operations on uninitialized kobjects
  MD RAID5: Avoid accessing gendisk or queue structs when not available
  md/raid5: schedule_construction should abort if nothing to do.

Pull libata updates from Jeff Garzik:
 "Simple stuff.  See one-line summaries."

* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  pata_samsung_cf: use module_platform_driver_probe()
  [libata] Avoid specialized TLA's in ZPODD's Kconfig
  libata-acpi.c: fix copy and paste mistake in ata_acpi_register_power_resource
  sata_fsl: Remove redundant NULL check before kfree
  ahci: Add Device IDs for Intel Wellsburg PCH
  ata_piix: Add MODULE_PARM_DESC to prefer_ms_hyperv

Pull i2c fixes from Wolfram Sang:
 "One bugfix for the tegra driver.  Two updates regarding email
  addresses and MAINTAINERS which I like to have up-to-date so people
  can be reached immediately.  While we are here, there is on PCI_ID
  addition."

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  MAINTAINERS: add maintainer entry for atmel i2c driver
  i2c: Fix my e-mail address in drivers and documentation
  i2c: iSMT: add Intel Avoton DeviceIDs
  i2c: tegra: check the clk_prepare_enable() return value

Pull watchdog fixes from Wim Van Sebroeck:
 "Fix a boot issues and correct the AcpiMmioSel bitmask in the
  sp5100_tco watchdog device driver"

* git://www.linux-watchdog.org/linux-watchdog:
  watchdog: sp5100_tco: Set the AcpiMmioSel bitmask value to 1 instead of 2
  watchdog: sp5100_tco: Remove code that may cause a boot failure

When KMS has parsed an EDID "detailed timing", it leaves the frame rate
zeroed.  Consecutive (debug-) output of that mode thus yields 0 for
vsync.  This simple fix also speeds up future invocations of
drm_mode_vrefresh().

While it is debatable whether this qualifies as a -stable fix I'd apply
it for consistency's sake; drm_helper_probe_single_connector_modes()
does the same thing already for all probed modes.

Cc: stable@vger.kernel.org
Signed-off-by: Torsten Duwe <duwe@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

EDID spreads some values across multiple bytes; bit-fiddling is needed
to retrieve these.  The current code to parse "detailed timings" has a
cut&paste error that results in a vsync offset of at most 15 lines
instead of 63.

See

   http://en.wikipedia.org/wiki/EDID

and in the "EDID Detailed Timing Descriptor" see bytes 10+11 show why
that needs to be a left shift.

Cc: stable@vger.kernel.org
Signed-off-by: Torsten Duwe <duwe@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull NVMe driver update from Matthew Wilcox:
 "These patches have mostly been baking for a few months; sorry I didn't
  get them in during the merge window.  They're all bug fixes, except
  for the addition of the SMART log and the addition to MAINTAINERS."

* git://git.infradead.org/users/willy/linux-nvme:
  NVMe: Add namespaces with no LBA range feature
  MAINTAINERS: Add entry for the NVMe driver
  NVMe: Initialize iod nents to 0
  NVMe: Define SMART log
  NVMe: Add result to nvme_get_features
  NVMe: Set result from user admin command
  NVMe: End queued bio requests when freeing queue
  NVMe: Free cmdid on nvme_submit_bio error

Merge misc fixes from Andrew Morton.

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  mqueue: sys_mq_open: do not call mnt_drop_write() if read-only
  mm/hotplug: only free wait_table if it's allocated by vmalloc
  dma-debug: update DMA debug API to better handle multiple mappings of a buffer
  dma-debug: fix locking bug in check_unmap()
  drivers/rtc/rtc-at91rm9200.c: use a variable for storing IMR
  drivers/video/ep93xx-fb.c: include <linux/io.h> for devm_ioremap()
  drivers/rtc/rtc-da9052.c: fix for rtc device registration
  mm: zone_end_pfn is too small
  poweroff: change orderly_poweroff() to use schedule_work()
  mm/hugetlb: fix total hugetlbfs pages count when using memory overcommit accouting
  printk: Provide a wake_up_klogd() off-case
  irq_work.h: fix warning when CONFIG_IRQ_WORK=n