- 09 Oct, 2018 5 commits
-
-
Javier González authored
In pblk, when a new line is allocated, metadata for the previously written line is scheduled. This is done through a fixed memory region that is shared through time and contexts across different lines and therefore protected by a lock. Unfortunately, this lock is not properly covering all the metadata used for sharing this memory regions, resulting in a race condition. This patch fixes this race condition by protecting this metadata properly. Fixes: dd2a4343 ("lightnvm: pblk: sched. metadata on write thread") Signed-off-by:
Javier González <javier@cnexlabs.com> Signed-off-by:
Matias Bjørling <mb@lightnvm.io> Signed-off-by:
Jens Axboe <axboe@kernel.dk>
-
Matias Bjørling authored
A 1.2 device is able to manage the logical to physical mapping table internally or leave it to the host. A target only supports one of those approaches, and therefore must check on initialization. Move this check to core to avoid each target implement the check. Signed-off-by:
-
Matias Bjørling authored
rqd.error is masked by the return value of pblk_submit_io_sync. The rqd structure is then passed on to the end_io function, which assumes that any error should lead to a chunk being marked offline/bad. Since the pblk_submit_io_sync can fail before the command is issued to the device, the error value maybe not correspond to a media failure, leading to chunks being immaturely retired. Also, the pblk_blk_erase_sync function prints an error message in case the erase fails. Since the caller prints an error message by itself, remove the error message in this function. Signed-off-by:
Hans Holmberg <hans.holmberg@cnexlabs.com> Signed-off-by:
-
Matias Bjørling authored
Add nvm_set_flags helper to enable core to appropriately set the command flags for read/write/erase depending on which version a drive supports. The flags arguments can be distilled into the access hint, scrambling, and program/erase suspend. Replace the access hint with a "is_seq" parameter. The rest of the flags are dependent on the command opcode, which is trivial to detect and set. Signed-off-by:
-
Matias Bjørling authored
No need to force NVMe device driver to be compiled in if the lightnvm subsystem is selected. Also no need for PCI to be selected as well, as it would be selected by the device driver that hooks into the subsystem. Signed-off-by:
-
- 08 Oct, 2018 16 commits
-
-
Ming Lei authored
Lot of controllers may have only one irq vector for completing IO request. And usually affinity of the only irq vector is all possible CPUs, however, on most of ARCH, there may be only one specific CPU for handling this interrupt. So if all IOs are completed in hardirq context, it is inevitable to degrade IO performance because of increased irq latency. This patch tries to address this issue by allowing to complete request in softirq context, like the legacy IO path. IOPS is observed as ~13%+ in the following randread test on raid0 over virtio-scsi. mdadm --create --verbose /dev/md0 --level=0 --chunk=1024 --raid-devices=8 /dev/sdb /dev/sdc /dev/sdd /dev/sde /dev/sdf /dev/sdg /dev/sdh /dev/sdi fio --time_based --name=benchmark --runtime=30 --filename=/dev/md0 --nrfiles=1 --ioengine=libaio --iodepth=32 --direct=1 --invalidate=1 --verify=0 --verify_fatal=0 --numjobs=32 --rw=randread --blocksize=4k Cc: Dongli Zhang <dongli.zhang@oracle.com> Cc: Zach Marano <zmarano@google.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Bart Van Assche <bvanassche@acm.org> Cc: Jianchao Wang <jianchao.w.wang@oracle.com> Signed-off-by:
Ming Lei <ming.lei@redhat.com> Signed-off-by:
-
Dongbo Cao authored
when the nbuckets of cache device is smaller than 1024, making cache device will trigger BUG_ON in kernel, add a condition to avoid this. Reported-by:
nitroxis <n@nxs.re> Signed-off-by:
Dongbo Cao <cdbdyx@163.com> Signed-off-by:
Coly Li <colyli@suse.de> Signed-off-by:
-
Dongbo Cao authored
Split the combined '||' statements in if() check, to make the code easier for debug. Signed-off-by:
-
Shenghui Wang authored
Current cache_set has MAX_CACHES_PER_SET caches most, and the macro is used for " struct cache *cache_by_alloc[MAX_CACHES_PER_SET]; " in the define of struct cache_set. Use MAX_CACHES_PER_SET instead of magic number 8 in __bch_bucket_alloc_set. Signed-off-by:
Shenghui Wang <shhuiw@foxmail.com> Signed-off-by:
-
Coly Li authored
In extents.c:bch_extent_bad(), number 96 is used as parameter to call btree_bug_on(). The purpose is to check whether stale gen value exceeds BUCKET_GC_GEN_MAX, so it is better to use macro BUCKET_GC_GEN_MAX to make the code more understandable. Signed-off-by:
-
Dongbo Cao authored
Parameter "struct kobject *kobj" in bch_debug_init() is useless, remove it in this patch. Signed-off-by:
-
Shenghui Wang authored
struct kmem_cache *bch_passthrough_cache is not used in bcache code. Remove it. Signed-off-by:
-
Shenghui Wang authored
Recal cached_dev_sectors on cached_dev detached, as recal done on cached_dev attached. Update the cached_dev_sectors before bcache_device_detach called as bcache_device_detach will set bcache_device->c to NULL. Signed-off-by:
-
Tang Junhui authored
refill->end record the last key of writeback, for example, at the first time, keys (1,128K) to (1,1024K) are flush to the backend device, but the end key (1,1024K) is not included, since the bellow code: if (bkey_cmp(k, refill->end) >= 0) { ret = MAP_DONE; goto out; } And in the next time when we refill writeback keybuf again, we searched key start from (1,1024K), and got a key bigger than it, so the key (1,1024K) missed. This patch modify the above code, and let the end key to be included to the writeback key buffer. Signed-off-by:Tang Junhui <tang.junhui.linux@gmail.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Ben Peddell authored
Forgot to include the maintainers with my first email. Somewhere between Michael Lyle's original "bcache: PI controller for writeback rate V2" patch dated 07 Sep 2017 and 1d316e65 bcache: implement PI controller for writeback rate, the mapping of the writeback_rate_minimum attribute was dropped. Re-add the missing sysfs writeback_rate_minimum attribute mapping to "allow the user to specify a minimum rate at which dirty blocks are retired." Fixes: 1d316e65 ("bcache: implement PI controller for writeback rate") Signed-off-by:
Ben Peddell <klightspeed@killerwolves.net> Signed-off-by:
-
Tang Junhui authored
When bcache device is clean, dirty keys may still exist after journal replay, so we need to count these dirty keys even device in clean status, otherwise after writeback, the amount of dirty data would be incorrect. Signed-off-by:
-
Coly Li authored
The code comments of closure_return_with_destructor() in closure.h makrs function name as closure_return(). This patch fixes this type with the correct name - closure_return_with_destructor. Signed-off-by:
-
Tang Junhui authored
When doing ioctl in flash device, it will call ioctl_dev() in super.c, then we should not to get cached device since flash only device has no backend device. This patch just move the jugement dc->io_disable to cached_dev_ioctl() to make ioctl in flash device correctly. Fixes: 0f0709e6 ("bcache: stop bcache device when backing device is offline") Signed-off-by:
-
Coly Li authored
In cached_dev_cache_miss() and check_should_bypass(), REQ_META is used to check whether a bio is for metadata request. REQ_META is used for blktrace, the correct REQ_ flag should be REQ_PRIO. This flag means the bio should be prior to other bio, and frequently be used to indicate metadata io in file system code. This patch replaces REQ_META with correct flag REQ_PRIO. CC Adam Manzanares because he explains to me what REQ_PRIO is for. Signed-off-by:
-
Tang Junhui authored
Missed reading IOs are identified by s->cache_missed, not the s->cache_miss, so in trace_bcache_read() using trace_bcache_read to identify whether the IO is missed or not. Signed-off-by:
-
Shenghui Wang authored
UUIDs are considered as metadata. __uuid_write should add the number of buckets (in sectors) written to disk to ca->meta_sectors_written. Currently only 1 bucket is used in uuid write. Steps to test: 1) create a fresh backing device and a fresh cache device separately. The backing device didn't attach to any cache set. 2) cd /sys/block/<cache device>/bcache cat metadata_written // record the output value cat bucket_size 3) attach the backing device to cache set 4) cat metadata_written The output value is almost the same as the value in step 2 before the change. After the change, the value is bigger about 1 bucket size. Signed-off-by:
-
- 05 Oct, 2018 3 commits
-
-
Bart Van Assche authored
When debugging e.g. the SCSI timeout handler it is important that requests that have not yet been started or that already have completed are also reported through debugfs. Cc: Christoph Hellwig <hch@lst.de> Cc: Ming Lei <ming.lei@redhat.com> Cc: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by:
Hannes Reinecke <hare@suse.com> Reviewed-by:
Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by:
Bart Van Assche <bvanassche@acm.org> Signed-off-by:
-
git://git.infradead.org/nvmeJens Axboe authored
Pull NVMe updates from Christoph: "A relatively boring merge window: - better AEN tracing (Chaitanya) - NUMA aware PCIe multipathing (me) - RDMA workqueue fixes (Sagi) - better bio usage in the target (Sagi) - FC rework for target removal (James) - better multipath handling of ->queue_rq failures (James) - various cleanups (Milan)" * 'nvme-4.20' of git://git.infradead.org/nvme: nvmet-rdma: use a private workqueue for delete nvme: take node locality into account when selecting a path nvmet: don't split large I/Os unconditionally nvme: call nvme_complete_rq when nvmf_check_ready fails for mpath I/O nvme-core: add async event trace helper nvme_fc: add 'nvme_discovery' sysfs attribute to fc transport device nvmet_fc: support target port removal with nvmet layer nvme-fc: fix for a minor typos nvmet: remove redundant module prefix nvme: fix typo in nvme_identify_ns_descs
-
Sagi Grimberg authored
Queue deletion is done asynchronous when the last reference on the queue is dropped. Thus, in order to make sure we don't over allocate under a connect/disconnect storm, we let queue deletion complete before making forward progress. However, given that we flush the system_wq from rdma_cm context which runs from a workqueue context, we can have a circular locking complaint [1]. Fix that by using a private workqueue for queue deletion. [1]: ====================================================== WARNING: possible circular locking dependency detected 4.19.0-rc4-dbg+ #3 Not tainted ------------------------------------------------------ kworker/5:0/39 is trying to acquire lock: 00000000a10b6db9 (&id_priv->handler_mutex){+.+.}, at: rdma_destroy_id+0x6f/0x440 [rdma_cm] but task is already holding lock: 00000000331b4e2c ((work_completion)(&queue->release_work)){+.+.}, at: process_one_work+0x3ed/0xa20 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #3 ((work_completion)(&queue->release_work)){+.+.}: process_one_work+0x474/0xa20 worker_thread+0x63/0x5a0 kthread+0x1cf/0x1f0 ret_from_fork+0x24/0x30 -> #2 ((wq_completion)"events"){+.+.}: flush_workqueue+0xf3/0x970 nvmet_rdma_cm_handler+0x133d/0x1734 [nvmet_rdma] cma_ib_req_handler+0x72f/0xf90 [rdma_cm] cm_process_work+0x2e/0x110 [ib_cm] cm_req_handler+0x135b/0x1c30 [ib_cm] cm_work_handler+0x2b7/0x38cd [ib_cm] process_one_work+0x4ae/0xa20 nvmet_rdma:nvmet_rdma_cm_handler: nvmet_rdma: disconnected (10): status 0 id 0000000040357082 worker_thread+0x63/0x5a0 kthread+0x1cf/0x1f0 ret_from_fork+0x24/0x30 nvme nvme0: Reconnecting in 10 seconds... -> #1 (&id_priv->handler_mutex/1){+.+.}: __mutex_lock+0xfe/0xbe0 mutex_lock_nested+0x1b/0x20 cma_ib_req_handler+0x6aa/0xf90 [rdma_cm] cm_process_work+0x2e/0x110 [ib_cm] cm_req_handler+0x135b/0x1c30 [ib_cm] cm_work_handler+0x2b7/0x38cd [ib_cm] process_one_work+0x4ae/0xa20 worker_thread+0x63/0x5a0 kthread+0x1cf/0x1f0 ret_from_fork+0x24/0x30 -> #0 (&id_priv->handler_mutex){+.+.}: lock_acquire+0xc5/0x200 __mutex_lock+0xfe/0xbe0 mutex_lock_nested+0x1b/0x20 rdma_destroy_id+0x6f/0x440 [rdma_cm] nvmet_rdma_release_queue_work+0x8e/0x1b0 [nvmet_rdma] process_one_work+0x4ae/0xa20 worker_thread+0x63/0x5a0 kthread+0x1cf/0x1f0 ret_from_fork+0x24/0x30 Fixes: 777dc823 ("nvmet-rdma: occasionally flush ongoing controller teardown") Reported-by:Sagi Grimberg <sagi@grimberg.me> Tested-by:
Christoph Hellwig <hch@lst.de>
-
- 03 Oct, 2018 2 commits
-
-
Bart Van Assche authored
Some time ago REQ_DISCARD was renamed into REQ_OP_DISCARD. Some comments and documentation files were not updated however. Update these comments and documentation files. See also commit 4e1b2d52 ("block, fs, drivers: remove REQ_OP compat defs and related code"). Signed-off-by:
Bart Van Assche <bart.vanassche@wdc.com> Cc: Mike Christie <mchristi@redhat.com> Cc: Martin K. Petersen <martin.petersen@oracle.com> Cc: Philipp Reisner <philipp.reisner@linbit.com> Cc: Lars Ellenberg <lars.ellenberg@linbit.com> Signed-off-by:
-
Young_X authored
There is another cast from unsigned long to int which causes a bounds check to fail with specially crafted input. The value is then used as an index in the slot array in cdrom_slot_status(). This issue is similar to CVE-2018-16658 and CVE-2018-10940. Signed-off-by:
Young_X <YangX92@hotmail.com> Signed-off-by:
-
- 02 Oct, 2018 1 commit
-
-
Gustavo A. R. Silva authored
Replace "fallthru" with a proper "fall through" annotation. This fix is part of the ongoing efforts to enabling -Wimplicit-fallthrough Signed-off-by:
Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by:
-
- 01 Oct, 2018 10 commits
-
-
Christoph Hellwig authored
Make current_path an array with an entry for every possible node, and cache the best path on a per-node basis. Take the node distance into account when selecting it. This is primarily useful for dual-ported PCIe devices which are connected to PCIe root ports on different sockets. Signed-off-by:
Keith Busch <keith.busch@intel.com> Reviewed-by:
-
Sagi Grimberg authored
If we know that the I/O size exceeds our inline bio vec, no point using it and split the rest to begin with. We could in theory reuse the inline bio and only allocate the bio_vec, but its really not worth optimizing for. Signed-off-by:
-
James Smart authored
When an io is rejected by nvmf_check_ready() due to validation of the controller state, the nvmf_fail_nonready_command() will normally return BLK_STS_RESOURCE to requeue and retry. However, if the controller is dying or the I/O is marked for NVMe multipath, the I/O is failed so that the controller can terminate or so that the io can be issued on a different path. Unfortunately, as this reject point is before the transport has accepted the command, blk-mq ends up completing the I/O and never calls nvme_complete_rq(), which is where multipath may preserve or re-route the I/O. The end result is, the device user ends up seeing an EIO error. Example: single path connectivity, controller is under load, and a reset is induced. An I/O is received: a) while the reset state has been set but the queues have yet to be stopped; or b) after queues are started (at end of reset) but before the reconnect has completed. The I/O finishes with an EIO status. This patch makes the following changes: - Adds the HOST_PATH_ERROR pathing status from TP4028 - Modifies the reject point such that it appears to queue successfully, but actually completes the io with the new pathing status and calls nvme_complete_rq(). - nvme_complete_rq() recognizes the new status, avoids resetting the controller (likely was already done in order to get this new status), and calls the multipather to clear the current path that errored. This allows the next command (retry or new command) to select a new path if there is one. Signed-off-by:James Smart <jsmart2021@gmail.com> Reviewed-by:
-
Chaitanya Kulkarni authored
This patch adds a new event for nvme async event notification. We print the async event in the decoded format when we recognize the event otherwise we just dump the result. Signed-off-by:
Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com> Signed-off-by:
-
James Smart authored
The fc transport device should allow for a rediscovery, as userspace might have lost the events. Example is udev events not handled during system startup. This patch add a sysfs entry 'nvme_discovery' on the fc class to have it replay all udev discovery events for all local port/remote port address pairs. Signed-off-by:
-
James Smart authored
Currently, if a targetport has been connected to via the nvmet config (in other words, the add_port() transport routine called, and the nvmet port pointer stored for using in upcalls on new io), and if the targetport is then removed (say the lldd driver decides to unload or fully reset its hardware) and then re-added (the lldd driver reloads or reinits its hardware), the port pointer has been lost so there's no way to continue to post commands up to nvmet via the transport port. Correct by allocating a small "port context" structure that will be linked to by the targetport. The context will save the targetport WWN's and the nvmet port pointer to use for it. Initial allocation will occur when the targetport is bound to via add_port. The context will be deallocated when remove_port() is called. If a targetport is removed while nvmet has the active port context, the targetport will be unlinked from the port context before removal. If a new targetport is registered, the port contexts without a binding are looked through and if the WWN's match (so it's the same as nvmet's port context) the port context is linked to the new target port. Thus new io can be received on the new targetport and operation resumes with nvmet. Additionally, this also resolves nvmet configuration changing out from underneath of the nvme-fc target port (for example: a nvmetcli clear). Signed-off-by:
James Smart <james.smart@broadcom.com> Signed-off-by:
-
Milan P. Gandhi authored
Signed-off-by:
Milan P. Gandhi <mgandhi@redhat.com> Reviewed-by:
-
Chaitanya Kulkarni authored
This patch removes the redundant module prefix used in the pr_err() when nvmet_get_smart_log_nsid() failed to find the namespace provided as a part of smart-log command. Signed-off-by:
-
Milan P. Gandhi authored
Signed-off-by:
-
Jens Axboe authored
Merge -rc6 in, for two reasons: 1) Resolve a trivial conflict in the blk-mq-tag.c documentation 2) A few important regression fixes went into upstream directly, so they aren't in the 4.20 branch. Signed-off-by:
-
- 30 Sep, 2018 3 commits
-
-
Greg Kroah-Hartman authored
-
https://github.com/ojeda/linuxGreg Kroah-Hartman authored
Miguel writes: "A trivial fix for auxdisplay - MAINTAINERS reference fix for moved file Reported by Joe Perches" * tag 'auxdisplay-for-greg-v4.19-rc6' of https://github.com/ojeda/linux: MAINTAINERS: fix reference to moved drivers/{misc => auxdisplay}/panel.c -
Greg Kroah-Hartman authored
Merge tag 'libnvdimm-fixes2-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm Dan writes: "filesystem-dax for 4.19-rc6 Fix a deadlock in the new for 4.19 dax_lock_mapping_entry() routine." * tag 'libnvdimm-fixes2-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: dax: Fix deadlock in dax_lock_mapping_entry()
-
