The new route handling in ip_mc_finish_output() from 'net' overlapped
with the new support for returning congestion notifications from BPF
programs.

In order to handle this I had to take the dev_loopback_xmit() calls
out of the switch statement.

The aquantia driver conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
nfp: extend flower capabilities for GRE tunnel offload

Pieter says:

This set extends the flower match and action components to offload
GRE decapsulation with classification and encapsulation actions. The
first 3 patches are refactor and cleanup patches for improving
readability and reusability. Patch 4 and 5 implement GRE decap and
encap functionality respectively.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add new GRE encapsulation support, which allows offload of filters
using tunnel_key set action in combination with actions that egress
to GRE type ports.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend the existing tunnel matching support to include GRE decap
classification. Specifically matching existing tunnel fields for
NVGRE (GRE with protocol field set to TEB).
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously tunnel related functions in action offload only applied
to UDP tunnels. Rename these functions in preparation for new
tunnel types.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adds IPv4 address and TTL/TOS helper functions, which is done in
preparation for compiling new tunnel types.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Refactor the key layer calculation function, in particular the tunnel
key layer calculation by introducing helper functions. This is done
in preparation for supporting GRE tunnel offloads.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marek Vasut says:

====================
net: dsa: microchip: Further regmap cleanups

This patchset cleans up KSZ9477 switch driver by replacing various
ad-hoc polling implementations and register RMW with regmap functions.

Each polling function is replaced separately to make it easier to review
and possibly bisect, but maybe the patches can be squashed.
====================
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Regmap provides read-modify-write function to update bitfields in
registers. Replace ad-hoc read-modify-write with regmap_update_bits()
where applicable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Regmap provides polling function to poll for bits in a register. This
function is another reimplementation of polling for bit being clear in
a register. Replace this with regmap polling function. Moreover, inline
the function parameters, as the function is never called with any other
parameter values than this one.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Regmap provides polling function to poll for bits in a register. This
function is another reimplementation of polling for bit being clear in
a register. Replace this with regmap polling function. Moreover, inline
the function parameters, as the function is never called with any other
parameter values than this one.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Regmap provides polling function to poll for bits in a register. This
function is another reimplementation of polling for bit being clear in
a register. Replace this with regmap polling function. Moreover, inline
the function parameters, as the function is never called with any other
parameter values than this one.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Regmap provides polling function to poll for bits in a register,
use in instead of reimplementing it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull clk fixes from Stephen Boyd:
 "A handful of clk driver fixes and one core framework fix

   - Do a DT/firmware lookup in clk_core_get() even when the DT index is
     a nonsensical value

   - Fix some clk data typos in the Amlogic DT headers/code

   - Avoid returning junk in the TI clk driver when an invalid clk is
     looked for

   - Fix dividers for the emac clks on Stratix10 SoCs

   - Fix default HDA rates on Tegra210 to correct distorted audio"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: socfpga: stratix10: fix divider entry for the emac clocks
  clk: Do a DT parent lookup even when index < 0
  clk: tegra210: Fix default rates for HDA clocks
  clk: ti: clkctrl: Fix returning uninitialized data
  clk: meson: meson8b: fix a typo in the VPU parent names array variable
  clk: meson: fix MPLL 50M binding id typo

Merge tag 'for-5.2/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm

Pull device mapper fixes from Mike Snitzer:

 - Fix incorrect uses of kstrndup and DM logging macros in DM's early
   init code.

 - Fix DM log-writes target's handling of super block sectors so updates
   are made in order through use of completion.

 - Fix DM core's argument splitting code to avoid undefined behaviour
   reported as a side-effect of UBSAN analysis on ppc64le.

 - Fix DM verity target to limit the amount of error messages that can
   result from a corrupt block being found.

* tag 'for-5.2/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm verity: use message limit for data block corruption message
  dm table: don't copy from a NULL pointer in realloc_argv()
  dm log writes: make sure super sector log updates are written in order
  dm init: remove trailing newline from calls to DMERR() and DMINFO()
  dm init: fix incorrect uses of kstrndup()

Pull pidfd fixes from Christian Brauner:
 "Userspace tools and libraries such as strace or glibc need a cheap and
  reliable way to tell whether CLONE_PIDFD is supported. The easiest way
  is to pass an invalid fd value in the return argument, perform the
  syscall and verify the value in the return argument has been changed
  to a valid fd.

  However, if CLONE_PIDFD is specified we currently check if pidfd == 0
  and return EINVAL if not.

  The check for pidfd == 0 was originally added to enable us to abuse
  the return argument for passing additional flags along with
  CLONE_PIDFD in the future.

  However, extending legacy clone this way would be a terrible idea and
  with clone3 on the horizon and the ability to reuse CLONE_DETACHED
  with CLONE_PIDFD there's no real need for this clutch. So remove the
  pidfd == 0 check and help userspace out.

  Also, accordig to Al, anon_inode_getfd() should only be used past the
  point of no failure and ksys_close() should not be used at all since
  it is far too easy to get wrong. Al's motto being "basically, once
  it's in descriptor table, it's out of your control". So Al's patch
  switches back to what we already had in v1 of the original patchset
  and uses a anon_inode_getfile() + put_user() + fd_install() sequence
  in the success path and a fput() + put_unused_fd() in the failure
  path.

  The other two changes should be trivial"

* tag 'for-linus-20190627' of gitolite.kernel.org:pub/scm/linux/kernel/git/brauner/linux:
  proc: remove useless d_is_dir() check
  copy_process(): don't use ksys_close() on cleanups
  samples: make pidfd-metadata fail gracefully on older kernels
  fork: don't check parent_tidptr with CLONE_PIDFD

Pull HID fixes from Jiri Kosina:

 - fix for one corner case in HID++ protocol with respect to handling
   very long reports, from Hans de Goede

 - power management fix in Intel-ISH driver, from Hyungwoo Yang

 - use-after-free fix in Intel-ISH driver, from Dan Carpenter

 - a couple of new device IDs/quirks from Kai-Heng Feng, Kyle Godbey and
   Oleksandr Natalenko

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
  HID: intel-ish-hid: fix wrong driver_data usage
  HID: multitouch: Add pointstick support for ALPS Touchpad
  HID: logitech-dj: Fix forwarding of very long HID++ reports
  HID: uclogic: Add support for Huion HS64 tablet
  HID: chicony: add another quirk for PixArt mouse
  HID: intel-ish-hid: Fix a use after free in load_fw_from_host()

Pull ARM SoC fixes from Olof Johansson:
 "A smaller batch of fixes, nothing that stands out as risky or scary.

  Mostly DTS tweaks for a few issues:

   - GPU fixlets for Meson

   - CPU idle fix for LS1028A

   - PWM interrupt fixes for i.MX6UL

  Also, enable a driver (FSL_EDMA) on arm64 defconfig, and a warning and
  two MAINTAINER tweaks"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
  ARM: dts: imx6ul: fix PWM[1-4] interrupts
  ARM: omap2: remove incorrect __init annotation
  ARM: dts: gemini Fix up DNS-313 compatible string
  ARM: dts: Blank D-Link DIR-685 console
  arm64: defconfig: Enable FSL_EDMA driver
  arm64: dts: ls1028a: Fix CPU idle fail.
  MAINTAINERS: BCM53573: Add internal Broadcom mailing list
  MAINTAINERS: BCM2835: Add internal Broadcom mailing list
  ARM: dts: meson8b: fix the operating voltage of the Mali GPU
  ARM: dts: meson8b: drop undocumented property from the Mali GPU node
  ARM: dts: meson8: fix GPU interrupts and drop an undocumented property

Pull AFS fixes from David Howells:
 "The in-kernel AFS client has been undergoing testing on opendev.org on
  one of their mirror machines. They are using AFS to hold data that is
  then served via apache, and Ian Wienand had reported seeing oopses,
  spontaneous machine reboots and updates to volumes going missing. This
  patch series appears to have fixed the problem, very probably due to
  patch (2), but it's not 100% certain.

  (1) Fix the printing of the "vnode modified" warning to exclude checks
      on files for which we don't have a callback promise from the
      server (and so don't expect the server to tell us when it
      changes).

      Without this, for every file or directory for which we still have
      an in-core inode that gets changed on the server, we may get a
      message logged when we next look at it. This can happen in bulk
      if, for instance, someone does "vos release" to update a R/O
      volume from a R/W volume and a whole set of files are all changed
      together.

      We only really want to log a message if the file changed and the
      server didn't tell us about it or we failed to track the state
      internally.

  (2) Fix accidental corruption of either afs_vlserver struct objects or
      the the following memory locations (which could hold anything).
      The issue is caused by a union that points to two different
      structs in struct afs_call (to save space in the struct). The call
      cleanup code assumes that it can simply call the cleanup for one
      of those structs if not NULL - when it might be actually pointing
      to the other struct.

      This means that every Volume Location RPC op is going to corrupt
      something.

  (3) Fix an uninitialised spinlock. This isn't too bad, it just causes
      a one-off warning if lockdep is enabled when "vos release" is
      called, but the spinlock still behaves correctly.

  (4) Fix the setting of i_block in the inode. This causes du, for
      example, to produce incorrect results, but otherwise should not be
      dangerous to the kernel"

* tag 'afs-fixes-20190620' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
  afs: Fix setting of i_blocks
  afs: Fix uninitialised spinlock afs_volume::cb_break_lock
  afs: Fix vlserver record corruption
  afs: Fix over zealous "vnode modified" warnings

Pull arch/csky fixup from Guo Ren:
 "A fixup patch for rt_sigframe in signal.c"

* tag 'csky-for-linus-5.2-fixup-gcc-unwind' of git://github.com/c-sky/csky-linux:
  csky: Fixup libgcc unwind error

Pull networking fixes from David Miller:

 1) Fix ppp_mppe crypto soft dependencies, from Takashi Iawi.

 2) Fix TX completion to be finite, from Sergej Benilov.

 3) Use register_pernet_device to avoid a dst leak in tipc, from Xin
    Long.

 4) Double free of TX cleanup in Dirk van der Merwe.

 5) Memory leak in packet_set_ring(), from Eric Dumazet.

 6) Out of bounds read in qmi_wwan, from Bjørn Mork.

 7) Fix iif used in mcast/bcast looped back packets, from Stephen
    Suryaputra.

 8) Fix neighbour resolution on raw ipv6 sockets, from Nicolas Dichtel.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (25 commits)
  af_packet: Block execution of tasks waiting for transmit to complete in AF_PACKET
  sctp: change to hold sk after auth shkey is created successfully
  ipv6: fix neighbour resolution with raw socket
  ipv6: constify rt6_nexthop()
  net: dsa: microchip: Use gpiod_set_value_cansleep()
  net: aquantia: fix vlans not working over bridged network
  ipv4: reset rt_iif for recirculated mcast/bcast out pkts
  team: Always enable vlan tx offload
  net/smc: Fix error path in smc_init
  net/smc: hold conns_lock before calling smc_lgr_register_conn()
  bonding: Always enable vlan tx offload
  net/ipv6: Fix misuse of proc_dointvec "skip_notify_on_dev_down"
  ipv4: Use return value of inet_iif() for __raw_v4_lookup in the while loop
  qmi_wwan: Fix out-of-bounds read
  tipc: check msg->req data len in tipc_nl_compat_bearer_disable
  net: macb: do not copy the mac address if NULL
  net/packet: fix memory leak in packet_set_ring()
  net/tls: fix page double free on TX cleanup
  net/sched: cbs: Fix error path of cbs_module_init
  tipc: change to use register_pernet_device
  ...

Saeed Mamameed says:

====================
Generic DIM

From: Tal Gilboa and Yamin Fridman

Implement net DIM over a generic DIM library, add RDMA DIM

dim.h lib exposes an implementation of the DIM algorithm for
dynamically-tuned interrupt moderation for networking interfaces.

We want a similar functionality for other protocols, which might need to
optimize interrupts differently. Main motivation here is DIM for NVMf
storage protocol.

Current DIM implementation prioritizes reducing interrupt overhead over
latency. Also, in order to reduce DIM's own overhead, the algorithm might
take some time to identify it needs to change profiles. While this is
acceptable for networking, it might not work well on other scenarios.

Here we propose a new structure to DIM. The idea is to allow a slightly
modified functionality without the risk of breaking Net DIM behavior for
netdev. We verified there are no degradations in current DIM behavior with
the modified solution.

Suggested solution:
- Common logic is implemented in lib/dim/dim.c
- Net DIM (existing) logic is implemented in lib/dim/net_dim.c, which uses
  the common logic in dim.c
- Any new DIM logic will be implemented in "lib/dim/new_dim.c".
  This new implementation will expose modified versions of profiles,
  dim_step() and dim_decision().
- DIM API is declared in include/linux/dim.h for all implementations.

Pros for this solution are:
- Zero impact on existing net_dim implementation and usage
- Relatively more code reuse (compared to two separate solutions)
- Increased extensibility
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The QCA8337(N) has a RESETn signal on Pin B42 that
triggers a chip reset if the line is pulled low.
The datasheet says that: "The active low duration
must be greater than 10 ms".

This can hopefully fix some of the issues related
to pin strapping in OpenWrt for the EA8500 which
suffers from detection issues after a SoC reset.

Please note that the qca8k_probe() function does
currently require to read the chip's revision
register for identification purposes.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch documents the qca8k's reset-gpios property that
can be used if the QCA8337N ends up in a bad state during
reset.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Gateway validation does not need a dst_entry, it only needs the fib
entry to validate the gateway resolution and egress device. So,
convert ip6_nh_lookup_table from ip6_pol_route to fib6_table_lookup
and ip6_route_check_nh to use fib6_lookup over rt6_lookup.

ip6_pol_route is a call to fib6_table_lookup and if successful a call
to fib6_select_path. From there the exception cache is searched for an
entry or a dst_entry is created to return to the caller. The exception
entry is not relevant for gateway validation, so what matters are the
calls to fib6_table_lookup and then fib6_select_path.

Similarly, rt6_lookup can be replaced with a call to fib6_lookup with
RT6_LOOKUP_F_IFACE set in flags. Again, the exception cache search is
not relevant, only the lookup with path selection. The primary difference
in the lookup paths is the use of rt6_select with fib6_lookup versus
rt6_device_match with rt6_lookup. When you remove complexities in the
rt6_select path, e.g.,
1. saddr is not set for gateway validation, so RT6_LOOKUP_F_HAS_SADDR
   is not relevant
2. rt6_check_neigh is not called so that removes the RT6_NUD_FAIL_DO_RR
   return and round-robin logic.

the code paths are believed to be equivalent for the given use case -
validate the gateway and optionally given the device. Furthermore, it
aligns the validation with onlink code path and the lookup path actually
used for rx and tx.

Adjust the users, ip6_route_check_nh_onlink and ip6_route_check_nh to
handle a fib6_info vs a rt6_info when performing validation checks.

Existing selftests fib-onlink-tests.sh and fib_tests.sh are used to
verify the changes.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
FDB, VLAN and PTP fixes for SJA1105 DSA

This patchset is an assortment of fixes for the net-next version of the
sja1105 DSA driver:
- Avoid a kernel panic when the driver fails to probe or unregisters
- Finish Arnd Bermann's idea of compiling PTP support as part of the
  main DSA driver and not separately
- Better handling of initial port-based VLAN as well as VLANs for
  dsa_8021q FDB entries
- Fix address learning for the SJA1105 P/Q/R/S family
- Make static FDB entries persistent across switch resets
- Fix reporting of statically-added FDB entries in 'bridge fdb show'
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The first generation switches don't tell us through the dynamic config
interface whether the dumped FDB entries are static or not (the LOCKEDS
bit from P/Q/R/S).

However, now that we're keeping a mirror of all 'bridge fdb' commands in
the static config, this is an opportunity to compare a dumped FDB entry
to the driver's private database.  After all, what makes an entry static
is that *we* added it.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A FDB entry means that "frames that match this VID and DMAC must be
forwarded to this port".

In the case of dsa_8021q however, the VID is not a single one (and
neither two, as my previous patch assumed). The VID can be set either by
the CPU port (1 tx_vid), or by any of the other front-panel port (n-1
rx_vid's).

Fixes: 93647594 ("net: dsa: sja1105: Hide the dsa_8021q VLANs from the bridge fdb command")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The reason why this wasn't tackled earlier is that I had hoped I
understood the user manual wrong.  But unfortunately hacks are required
in order to retrieve the static/dynamic nature of FDB entries on SJA1105
P/Q/R/S, since this info is stored in the writeback buffer of the
dynamic config command.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When trying to add support for LOCKEDS (static FDB entries) on SJA1105
P/Q/R/S, at first I didn't remember how the abstraction I created
worked, and actually thought it works by mistake.

To avoid other people staring at the code and not making much sense out
of it, add some comments at the top of the file.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit 8456721d ("net: dsa: sja1105: Add support for
configuring address ageing time"), we started to reset the switch rather
often (each time the bridge core changes the ageing time on a switch
port).

The unfortunate reality is that SJA1105 doesn't have any {cold, warm,
whatever} reset mode in which it accepts a new configuration stream
without flushing the FDB.  Instead, in its world, the FDB *is* an
optional part of the static configuration.

So we play its game, and do what we also do for VLANs: for each 'bridge
fdb' command, we add the FDB entry through the dynamic interface, and we
append the in-kernel static config memory with info that we're going to
use later, when the next reset command is going to be issued.

The result is that 'bridge fdb' commands are now persistent (dynamically
learned entries are lost, but that's ok).
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

At the end of the commit 1da73821 ("net: dsa: sja1105: Add FDB
operations for P/Q/R/S series") message, I said that:

    At the moment only FDB entries installed statically through 'bridge fdb'
    are visible in the dump callback - the dynamically learned ones are
    still under investigation.

It looks like the reason why they were not visible in 'bridge fdb' was
that they were never learned - always flooded.

SJA1105 P/Q/R/S manual says about the MAXADDRP[port] field:

    Specify the maximum number of MAC address dynamically learned from
    the respective port. It is used to limit the number of learned MAC
    addresses per port.

It looks like not providing a value in the static config (aka providing
zeroes) is enough for it to not store the learned addresses in the FDB.

For now we divide the 1024 entry FDB "equally" amongst the 5 ports. This
may be revisited if the situation calls for that - for now I'm happy
that learning works.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 1da73821 ("net: dsa: sja1105: Add FDB operations for
P/Q/R/S series"), these bits were set in the static config, but
apparently they did not do anything.  The reason is that the packing
accessors for them were part of a patch I forgot to send.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In SJA1105 there is no concept of 'default values' per se, everything
needs to be driver-supplied through the static configuration tables.

The issue is that the hardware manual says that 'at least the default
untagging VLAN' is mandatory to be provided through the static config.
But VLAN 0 isn't a very good initial pvid - its use is reserved for
priority-tagged frames, and the layers of the stack that care about
those already make sure that this VLAN is installed, as can be seen in
the message below:

  8021q: adding VLAN 0 to HW filter on device swp2

So change the pvid provided through the static configuration to 1, which
matches the bridge core's defaults.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently when the driver unloads and PTP is enabled, the delayed work
that prevents the timecounter from expiring becomes a ticking time bomb.
The kernel will schedule the work thread within 60 seconds of driver
removal, but the work handler is no longer there, leading to this
strange and inconclusive stack trace:

[   64.473112] Unable to handle kernel paging request at virtual address 79746970
[   64.480340] pgd = 008c4af9
[   64.483042] [79746970] *pgd=00000000
[   64.486620] Internal error: Oops: 80000005 [#1] SMP ARM
[   64.491820] Modules linked in:
[   64.494871] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.2.0-rc5-01634-ge3a2773ba9e5 #1246
[   64.503007] Hardware name: Freescale LS1021A
[   64.507259] PC is at 0x79746970
[   64.510393] LR is at call_timer_fn+0x3c/0x18c
[   64.514729] pc : [<79746970>]    lr : [<c03bd734>]    psr: 60010113
[   64.520965] sp : c1901de0  ip : 00000000  fp : c1903080
[   64.526163] r10: c1901e38  r9 : ffffe000  r8 : c19064ac
[   64.531363] r7 : 79746972  r6 : e98dd260  r5 : 00000100  r4 : c1a9e4a0
[   64.537859] r3 : c1900000  r2 : ffffa400  r1 : 79746972  r0 : e98dd260
[   64.544359] Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
[   64.551460] Control: 10c5387d  Table: a8a2806a  DAC: 00000051
[   64.557176] Process swapper/0 (pid: 0, stack limit = 0x1ddb27f0)
[   64.563147] Stack: (0xc1901de0 to 0xc1902000)
[   64.567481] 1de0: eb6a4918 3d60d7c3 c1a9e554 e98dd260 eb6a34c0 c1a9e4a0 ffffa400 c19064ac
[   64.575616] 1e00: ffffe000 c03bd95c c1901e34 c1901e34 eb6a34c0 c1901e30 c1903d00 c186f4c0
[   64.583751] 1e20: c1906488 29e34000 c1903080 c03bdca4 00000000 eaa6f218 00000000 eb6a45c0
[   64.591886] 1e40: eb6a45c0 20010193 00000003 c03c0a68 20010193 3f7231be c1903084 00000002
[   64.600022] 1e60: 00000082 00000001 ffffe000 c1a9e0a4 00000100 c0302298 02b64722 0000000f
[   64.608157] 1e80: c186b3c8 c1877540 c19064ac 0000000a c186b350 ffffa401 c1903d00 c1107348
[   64.616292] 1ea0: 00200102 c0d87a14 ea823c00 ffffe000 00000012 00000000 00000000 ea810800
[   64.624427] 1ec0: f0803000 c1876ba8 00000000 c034c784 c18774b8 c039fb50 c1906c90 c1978aac
[   64.632562] 1ee0: f080200c f0802000 c1901f10 c0709ca8 c03091a0 60010013 ffffffff c1901f44
[   64.640697] 1f00: 00000000 c1900000 c1876ba8 c0301a8c 00000000 000070a0 eb6ac1a0 c031da60
[   64.648832] 1f20: ffffe000 c19064ac c19064f0 00000001 00000000 c1906488 c1876ba8 00000000
[   64.656967] 1f40: ffffffff c1901f60 c030919c c03091a0 60010013 ffffffff 00000051 00000000
[   64.665102] 1f60: ffffe000 c0376aa4 c1a9da37 ffffffff 00000037 3f7231be c1ab20c0 000000cc
[   64.673238] 1f80: c1906488 c1906480 ffffffff 00000037 c1ab20c0 c1ab20c0 00000001 c0376e1c
[   64.681373] 1fa0: c1ab2118 c1700ea8 ffffffff ffffffff 00000000 c1700754 c17dfa40 ebfffd80
[   64.689509] 1fc0: 00000000 c17dfa40 3f7733be 00000000 00000000 c1700330 00000051 10c0387d
[   64.697644] 1fe0: 00000000 8f000000 410fc075 10c5387d 00000000 00000000 00000000 00000000
[   64.705788] [<c03bd734>] (call_timer_fn) from [<c03bd95c>] (expire_timers+0xd8/0x144)
[   64.713579] [<c03bd95c>] (expire_timers) from [<c03bdca4>] (run_timer_softirq+0xe4/0x1dc)
[   64.721716] [<c03bdca4>] (run_timer_softirq) from [<c0302298>] (__do_softirq+0x130/0x3c8)
[   64.729854] [<c0302298>] (__do_softirq) from [<c034c784>] (irq_exit+0xbc/0xd8)
[   64.737040] [<c034c784>] (irq_exit) from [<c039fb50>] (__handle_domain_irq+0x60/0xb4)
[   64.744833] [<c039fb50>] (__handle_domain_irq) from [<c0709ca8>] (gic_handle_irq+0x58/0x9c)
[   64.753143] [<c0709ca8>] (gic_handle_irq) from [<c0301a8c>] (__irq_svc+0x6c/0x90)
[   64.760583] Exception stack(0xc1901f10 to 0xc1901f58)
[   64.765605] 1f00:                                     00000000 000070a0 eb6ac1a0 c031da60
[   64.773740] 1f20: ffffe000 c19064ac c19064f0 00000001 00000000 c1906488 c1876ba8 00000000
[   64.781873] 1f40: ffffffff c1901f60 c030919c c03091a0 60010013 ffffffff
[   64.788456] [<c0301a8c>] (__irq_svc) from [<c03091a0>] (arch_cpu_idle+0x38/0x3c)
[   64.795816] [<c03091a0>] (arch_cpu_idle) from [<c0376aa4>] (do_idle+0x1bc/0x298)
[   64.803175] [<c0376aa4>] (do_idle) from [<c0376e1c>] (cpu_startup_entry+0x18/0x1c)
[   64.810707] [<c0376e1c>] (cpu_startup_entry) from [<c1700ea8>] (start_kernel+0x480/0x4ac)
[   64.818839] Code: bad PC value
[   64.821890] ---[ end trace e226ed97b1c584cd ]---
[   64.826482] Kernel panic - not syncing: Fatal exception in interrupt
[   64.832807] CPU1: stopping
[   64.835501] CPU: 1 PID: 0 Comm: swapper/1 Tainted: G      D           5.2.0-rc5-01634-ge3a2773ba9e5 #1246
[   64.845013] Hardware name: Freescale LS1021A
[   64.849266] [<c0312394>] (unwind_backtrace) from [<c030cc74>] (show_stack+0x10/0x14)
[   64.856972] [<c030cc74>] (show_stack) from [<c0ff4138>] (dump_stack+0xb4/0xc8)
[   64.864159] [<c0ff4138>] (dump_stack) from [<c0310854>] (handle_IPI+0x3bc/0x3dc)
[   64.871519] [<c0310854>] (handle_IPI) from [<c0709ce8>] (gic_handle_irq+0x98/0x9c)
[   64.879050] [<c0709ce8>] (gic_handle_irq) from [<c0301a8c>] (__irq_svc+0x6c/0x90)
[   64.886489] Exception stack(0xea8cbf60 to 0xea8cbfa8)
[   64.891514] bf60: 00000000 0000307c eb6c11a0 c031da60 ffffe000 c19064ac c19064f0 00000002
[   64.899649] bf80: 00000000 c1906488 c1876ba8 00000000 00000000 ea8cbfb0 c030919c c03091a0
[   64.907780] bfa0: 600d0013 ffffffff
[   64.911250] [<c0301a8c>] (__irq_svc) from [<c03091a0>] (arch_cpu_idle+0x38/0x3c)
[   64.918609] [<c03091a0>] (arch_cpu_idle) from [<c0376aa4>] (do_idle+0x1bc/0x298)
[   64.925967] [<c0376aa4>] (do_idle) from [<c0376e1c>] (cpu_startup_entry+0x18/0x1c)
[   64.933496] [<c0376e1c>] (cpu_startup_entry) from [<803025cc>] (0x803025cc)
[   64.940422] Rebooting in 3 seconds..

In this case, what happened is that the DSA driver failed to probe at
boot time due to a PHY issue during phylink_connect_phy:

[    2.245607] fsl-gianfar soc:ethernet@2d90000 eth2: error -19 setting up slave phy
[    2.258051] sja1105 spi0.1: failed to create slave for port 0.0

Fixes: bb77f36a ("net: dsa: sja1105: Add support for the PTP clock")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As Arnd Bergmann pointed out in commit 78fe8a28 ("net: dsa: sja1105:
fix ptp link error"), there is no point in having PTP support as a
separate loadable kernel module.

So remove the exported symbols and make sja1105.ko contain PTP support
or not based on CONFIG_NET_DSA_SJA1105_PTP.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marek Vasut says:

====================
net: dsa: microchip: Convert to regmap

This patchset converts KSZ9477 switch driver to regmap.

This was tested with extra patches on KSZ8795. This was also tested
on KSZ9477 on Microchip KSZ9477EVB board, which I now have.
====================
Signed-off-by: Marek Vasut <marex@denx.de>

Regmap provides bit manipulation functions to set/clear bits, use those
insted of reimplementing them.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The regmap config tables are rather similar for various generations of
the KSZ8xxx/KSZ9xxx switches. Introduce a macro which allows generating
those tables without duplication. Note that $regalign parameter is not
used right now, but will be used in KSZ87xx series switches.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since the driver now uses regmap , get rid of ad-hoc ksz_io_ops
abstraction, which no longer has any meaning. Moreover, since regmap
has it's own locking, get rid of the register access mutex.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>