The alignment requirement for 64-bit load/store instructions on ARM is
implementation defined. Some CPUs (such as Marvell Feroceon) do not
generate an exception, if such an instruction is executed with an
address that is not 64 bit aligned. In such a case, the Feroceon
corrupts adjacent memory, which showed up in my tests as a crash in the
rx path of ath9k that only occured with CONFIG_XFRM set.

This crash happened, because the first field of the mac80211 rx status
info in the cb is an u64, and changing it corrupted the skb->sp field.

This patch also closes some potential pre-existing holes in the sk_buff
struct surrounding the cb[] area.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

When the register_netdevice() call fails, the newly allocated device is
not freed.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit e8469ed959c373c2ff9e6f488aa5a14971aebe1f
Author: Patrick McHardy <kaber@trash.net>
Date:   Tue Feb 23 20:41:30 2010 +0100

Support specifying the initial device flags when creating a device though
rtnl_link. Devices allocated by rtnl_create_link() are marked as INITIALIZING
in order to surpress netlink registration notifications. To complete setup,
rtnl_configure_link() must be called, which performs the device flag changes
and invokes the deferred notifiers if everything went well.

Two examples:

# add macvlan to eth0
#
$ ip link add link eth0 up allmulticast on type macvlan

[LINK]11: macvlan0@eth0: <BROADCAST,MULTICAST,ALLMULTI,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN
    link/ether 26:f8:84:02:f9:2a brd ff:ff:ff:ff:ff:ff
[ROUTE]ff00::/8 dev macvlan0  table local  metric 256  mtu 1500 advmss 1440 hoplimit 0
[ROUTE]fe80::/64 dev macvlan0  proto kernel  metric 256  mtu 1500 advmss 1440 hoplimit 0
[LINK]11: macvlan0@eth0: <BROADCAST,MULTICAST,ALLMULTI,UP,LOWER_UP> mtu 1500
    link/ether 26:f8:84:02:f9:2a
[ADDR]11: macvlan0    inet6 fe80::24f8:84ff:fe02:f92a/64 scope link
       valid_lft forever preferred_lft forever
[ROUTE]local fe80::24f8:84ff:fe02:f92a via :: dev lo  table local  proto none  metric 0  mtu 16436 advmss 16376 hoplimit 0
[ROUTE]default via fe80::215:e9ff:fef0:10f8 dev macvlan0  proto kernel  metric 1024  mtu 1500 advmss 1440 hoplimit 0
[NEIGH]fe80::215:e9ff:fef0:10f8 dev macvlan0 lladdr 00:15:e9:f0:10:f8 router STALE
[ROUTE]2001:6f8:974::/64 dev macvlan0  proto kernel  metric 256  expires 0sec mtu 1500 advmss 1440 hoplimit 0
[PREFIX]prefix 2001:6f8:974::/64 dev macvlan0 onlink autoconf valid 14400 preferred 131084
[ADDR]11: macvlan0    inet6 2001:6f8:974:0:24f8:84ff:fe02:f92a/64 scope global dynamic
       valid_lft 86399sec preferred_lft 14399sec

# add VLAN to eth1, eth1 is down
#
$ ip link add link eth1 up type vlan id 1000
RTNETLINK answers: Network is down

<no events>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Split dev_change_flags() into two functions: __dev_change_flags() to
perform the actual changes and __dev_notify_flags() to invoke netdevice
notifiers. This will be used by rtnl_link to defer netlink notifications
until the device has been fully configured.

This changes ordering of some operations, in particular:

- netlink notifications are sent after all changes have been performed.
  As a side effect this surpresses one unnecessary netlink message when
  the IFF_UP and other flags are changed simultaneously.

- The NETDEV_UP/NETDEV_DOWN and NETDEV_CHANGE notifiers are invoked
  after all changes have been performed. Their relative is unchanged.

- net_dmaengine_put() is invoked before the NETDEV_DOWN notifier instead
  of afterwards. This should not make any difference since both RX and TX
  are already shut down at this point.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to support specifying device flags during device creation,
we must be able to roll back device registration in case setting the
flags fails without sending any notifications related to the device
to userspace.

This patch changes rollback_registered_many() and register_netdevice()
to manually send netlink notifications for devices not handled by
rtnl_link and allows to defer notifications for devices handled by
rtnl_link until setup is complete.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 3b8bcfd5 (net: introduce pre-up netdev notifier) added a new
notifier which is run before a device is set UP for use by cfg80211.

The patch missed to add the new notifier to the ignore list in
rtnetlink_event(), so we currently get an unnecessary netlink
notification before a device is set UP.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

MPC5121 FEC requeries 4-byte alignmnent for TX data buffers.
This patch is a work around that copies misaligned tx packets
to an aligned skb before sending.
Signed-off-by: John Rigby <jcrigby@gmail.com>
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend the fs_enet driver to support MPC512x FEC.
Enable it with CONFIG_FS_ENET_MPC5121_FEC option.
Signed-off-by: John Rigby <jcrigby@gmail.com>
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

This makes the b43 driver just automatically fall back to PIO mode when
DMA doesn't work.

The driver already told the user to do it, so rather than have the user
reload the module with a new flag, just make the driver do it
automatically. We keep the message as an indication that something is
wrong, but now just automatically fall back to the hopefully working PIO
case.

(Some post-2.6.33 merge fixups by Larry Finger <Larry.Finger@lwfinger.net>
and yours truly... -- JWL)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If authentication has already been performed when the WLAN interface is
stopped, (sometimes) the ieee80211_work_purge would corrupt some
ieee80211_work-structures. The outcome is this (cleaned up):

[ 2252.398681] WARNING: at net/mac80211/work.c:995 ieee80211_work_purge
[ 2252.466430] Backtrace:
[ 2252.529266] (ieee80211_work_purge+0x0/0xcc [mac80211])
[ 2252.546875] (ieee80211_stop+0x0/0x4c0 [mac80211])

Additionally, one would get this, going on regarless of the WLAN interface
state, going on forever:

[ 2252.859985] wlan0: direct probe to 00:90:4c:60:04:00 (try -996717525)
[ 2253.055419] wlan0: direct probe to 00:90:4c:60:04:00 (try -996717524)
[ 2253.250610] wlan0: direct probe to 00:90:4c:60:04:00 (try -996717523)
[ 2253.446014] wlan0: direct probe to 00:90:4c:60:04:00 (try -996717522)
[ 2253.641357] wlan0: direct probe to 00:90:4c:60:04:00 (try -996717521)
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In "wireless: remove WLAN_80211 and WLAN_PRE80211 from Kconfig" I
inadvertantly missed a line in include/linux/netdevice.h.  I thereby
effectively reverted "net: Set LL_MAX_HEADER properly for wireless." by
accident. :-(  Now we should check there for CONFIG_WLAN instead.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Cc: stable@kernel.org

Currently if a driver does not set hw.max_listen_interval a listen
interval of 1 is negotiated with the AP. Thus, the AP could drop
buffered frames for us after just one beacon interval which can
easily happen with the current powersave and scan implementation.
To avoid this issue increase the default interval to 5 which should
be a reasonable safe default.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

While ath9k does not support RIFS yet, the ability to receive RIFS
frames is currently enabled for most chipsets in the initvals.
This is causing baseband related issues on AR9160 and AR9130 based
chipsets, which can lock up under certain conditions.

This patch fixes these issues by overriding the initvals, effectively
disabling RIFS for all affected chipsets.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

I am no longer with Marvell.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'wireless-next-2.6' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-2.6

Conflicts:
	drivers/net/wireless/iwlwifi/iwl-core.h
	net/mac80211/rate.c

The ISA skeleton net driver has been obsolete and unmaintained for many
years.  Any hardware remotely like ISA will use the platform API and
look much more like a PCI driver, and make much better use of netdev
APIs such as NAPI.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>

Quick fix for memory/module refcount leak.
Reference count of listener instance never reaches 0.

Start/stop of ulogd2 is enough to trigger this bug!

Now, refcounting there looks very fishy in particular this code:

 	if (!try_module_get(THIS_MODULE)) {
		...

and creation of listener instance with refcount 2,
so it may very well be ripped and redone.  :-)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>

Use list_head rather than a custom list implementation.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Patrick McHardy <kaber@trash.net>

CAN module on AM3517 requires programming of IO expander as part
of init sequence - to enable CAN PHY. Added platform specific
callback to handle phy control(switch on /off).
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit c79c5ffd.

As Jeff points out we can't break the user visible interface
like this, we need to add this into the reserved[] thing.
Signed-off-by: David S. Miller <davem@davemloft.net>

Clients will set their MTU to 1280 if they receive a
ICMPV6_PKT_TOOBIG message with an MTU less than 1280.

To allow encapsulating of packets over a 1280 link
we should always accept packets with a size of 1280
for forwarding even if the path has a lower MTU and
fragment the encapsulated packets afterwards.

In case a forwarded packet is not going to be encapsulated
a ICMPV6_PKT_TOOBIG msg will still be send by ip6_fragment()
with the correct MTU.
Signed-off-by: Ulrich Weber <uweber@astaro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Due to the loop complexicity in nes_nic.c, I'm using char* to copy mc addresses
to it.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The drvinfo struct should include the number of strings that
get_rx_ntuple will return.  It will be variable if an underlying
driver implements its own get_rx_ntuple routine, so userspace
needs to know how much data is coming.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There doesn't seem to be any reason to explicitly return
NETDEV_TX_OK as err is set to NETDEV_TX_OK in all cases that
reach this point.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use list_first_entry macro; no longer any need to use
'next' directly in list to find first entry.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch consists of a few minor cleanups to the SR-IOV
configurion code in rtnetlink.
- Remove unneccesary lock
- Remove unneccesary casts
- Return correct error code for no driver support

These changes are based on comments from Patrick McHardy
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no point of accepting an address of smaller length than dev->addr_len
here. Therefore change this for stonger check.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Small optimization to the code which checks to see if we'd cross
a 4K boundary when stocking RX ring.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew Gallatin <gallatin@myri.com>
Signed-off-by: Guillaume Morin <guillaume@morinfr.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

RFC 4291 section 2.4 states that all uncategorized addresses
should be considered as Global Unicast.

This will remove IPV6_ADDR_RESERVED completely
and return IPV6_ADDR_UNICAST in ipv6_addr_type() instead.
Signed-off-by: Ulrich Weber <uweber@astaro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

And update copyright to 2010.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We only need to assign the status block address once and it also saves
space in the structure.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Eddie Wai <waie@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With a separate IP address for iSCSI, connections should proceed
whether or not we can get a route to the target from the network stack.
It is possible that the network IP address may not reach the iSCSI target.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Eddie Wai <waie@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some data structures are freed when the device is down and it will
crash if an ISCSI netlink message is received.  Add RCU protection
to prevent this.  In the shutdown path, ulp_ops[CNIC_ULP_L4] is
assigned NULL and rcu_synchronized before freeing the data
structures.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>