- 23 Jan, 2008 40 commits
-
-
Andrew Vasquez authored
Signed-off-by:
Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by:
James Bottomley <James.Bottomley@HansenPartnership.com>
-
Andrew Vasquez authored
Some flash parts have a slow enable write-protection (WP) operation whereby subsequent FLASH accesses would fail if the WP operation had not completed. Software now polls the SPI's status-register for WP completion. Signed-off-by:
-
Andrew Vasquez authored
The driver stores the contents of PCI resources into unsigned long's before ioremapping. This breaks on 32-bit platforms which support 64-bit MMIO resources. Correct code by removing the temporary variables used during MMIO PIO mapping and using resource_size_t where applicable. Also correct a small typo in a printk() where the wrong region number was displayed. Signed-off-by:
-
Andrew Vasquez authored
HBAs supporting these additional counters include ISP24xx and ISP25xx type boards. Signed-off-by:
-
Andrew Vasquez authored
Signed-off-by:
-
Kai Makisara authored
Convert st to unlocked_ioctl. The necessary locking was already in place. Signed-off-by:
Kai Makisara <kai.makisara@kolumbus.fi> Signed-off-by:
-
Salyzyn, Mark authored
I was amazed at how much embedded space was present in the aacraid driver source files. Just selected five files from the set to clean up for now and the attached patch swelled to 73K in size! - Removed trailing space or tabs - Removed spaces embedded within tabs - Replaced leading 8 spaces with tabs - Removed spaces before ) - Removed ClusterCommand as it was unused (noticed it as one triggered by above) - Replaced scsi_status comparison with 0x02, to compare against SAM_STATUS_CHECK_CONDITION. - Replaced a long series of spaces with tabs - Replaced some simple if...defined() with ifdef/ifndef Signed-off-by:
Mark Salyzyn <aacraid@adaptec.com> Signed-off-by:
-
FUJITA Tomonori authored
Signed-off-by:
FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Acked-by:
Douglas Gilbert <dougg@torque.net> Signed-off-by:
-
FUJITA Tomonori authored
If cdev_add fails in sg_add, sg_remove crashes since class_data is bogus. Signed-off-by:
-
Salyzyn, Mark authored
0x02 becomes SAM_STAT_CHECK_CONDITION Signed-off-by:
-
Mathieu Segaud authored
As of now, compat_ioctl already runs without the BKL, whereas ioctl runs with the BKL. This patch first converts changer_fops to use a .unlocked_ioctl member. It applies the same locking rationale than ch_ioctl_compat() uses to ch_ioctl(). Signed-off-by:
Mathieu Segaud <mathieu.segaud@regala.cx> Reviewed-by:
Matthew Wilcox <willy@linux.intel.com> Signed-off-by:
-
Andi Kleen authored
When I use cdparanoia my logs get spammed a lot by printk: 464 messages suppressed. sg_write: data in/out 30576/30576 bytes for SCSI command 0xbe--guessing data in; program cdparanoia not setting count and/or reply_len properly printk: 1078 messages suppressed. and many more of those. With this patch the message is only printed once for a command in a row. v1->v2: Prevent rate limit messages too (pointed out by jejb) Signed-off-by:
Andi Kleen <ak@suse.de> Acked-by:
-
Alan Cox authored
Actually there are several but one is trivially fixed 1. FSACTL_GET_NEXT_ADAPTER_FIB ioctl does not lock dev->fib_list but needs to 2. Ditto for FSACTL_CLOSE_GET_ADAPTER_FIB 3. It is possible to construct an attack via the SRB ioctls where the user obtains assorted elevated privileges. Various approaches are possible, the trivial ones being things like writing to the raw media via scsi commands and the swap image of other executing programs with higher privileges. So the ioctls should be CAP_SYS_RAWIO - at least all the FIB manipulating ones. This is a bandaid fix for #3 but probably the ioctls should grow their own capable checks. The other two bugs need someone competent in that driver to fix them. Signed-off-by:
Alan Cox <alan@redhat.com> Signed-off-by:
-
Salyzyn, Mark authored
The promised min_t() cleanup. Purely cosmetic. Signed-off-by:
-
FUJITA Tomonori authored
This replaces sizeof sense_buffer with SCSI_SENSE_BUFFERSIZE in several LLDs. It's a preparation for the future changes to remove sense_buffer array in scsi_cmnd structure. Signed-off-by:
-
FUJITA Tomonori authored
LLDs don't need to zero out scsi_cmnd::sense_buffer in queuecommand since scsi-ml does. This is a preparation of the future changes to allocate the sense_buffer only when necessary. Many LLDs zero out the sense_buffer before touching it on the error case. This patch lets them alone for now because new APIs for them would be added later on. Signed-off-by:
"Salyzyn, Mark" <Mark_Salyzyn@adaptec.com> Signed-off-by:
-
Randy Dunlap authored
Change megaraid_pci_driver_g variable name so that it matches the modpost whitelist that allows pointers to init text/data. WARNING: vmlinux.o(.data+0x1a8e30): Section mismatch: reference to .init.text:megaraid_probe_one (between 'megaraid_pci_driver_g' and 'class_device_attr_megaraid_mbox_app_hndl') Signed-off-by:
Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by:
-
FUJITA Tomonori authored
Signed-off-by:
-
Salyzyn, Mark authored
Due to an internal limit associated with the AdapterTypeText field, SMC required a product ID that overloaded the combined vendor and product ID. A decision was made to ship the SMC products without a vendor string dropping the defacto space that used to delineate vendor and product to boot. To correct this, we needed to adjust the code in the driver to parse out the vendor and product strings for the adapter. We match of 'AOC' in the AdapterTypeText, if so we set the vendor to SMC and place the entire AdapterTypeText into the product field. This only affects the cosmetic presentation of the Adapter vendor and product in the logs and in sysfs. Signed-off-by:
-
Salyzyn, Mark authored
Added support to respond to enclosure service events (controller AIFs) to add, online or offline physical targets reported to sg. Also added online and offlining of arrays. Removed an automatic variable definition in a sub block that hid an earlier definition, determined to be inert as the sub-block use did not interfere. Bumped the driver versioning to stamp the addition of this feature. Signed-off-by:
-
Krzysztof Helt authored
This patch fixes two bugs pointed by James Bottomley: 1. the if (!sym_data->io_reset). That variable is only ever filled by a stack based completion. If we find it non empty it means this code has been entered twice and we have a severe problem, so that should just become a BUG_ON(sym_data->io_reset). 2. sym_data->io_reset should be set to NULL before the routine is exited otherwise the PCI recovery code could end up completing what will be a bogus pointer into the stack. Big thanks to James Bottomley for help with the patch. Signed-off-by:Krzysztof Helt <krzysztof.h1@w.pl> Signed-off-by:
-
Salyzyn, Mark authored
Some architectures require a call to flush_kernel_dcache_page for processor spoofed DMA operations. Signed-off-by:
-
Prakash, Sathya authored
This patch fixes the module unload problem in flash less 1030 controller environment where firmware download boot functionality is invoked. The problem is due to the firmware download is being done in the reverse order, which this patch solves by insureing the download occurs to the last controller being reset. signed-off-by:
Sathya Prakash <sathya.prakash@lsi.com> Signed-off-by:
-
James Smart authored
Update lpfc driver version to 8.2.4 Signed-off-by:
James Smart <James.Smart@emulex.com> Signed-off-by:
-
James Smart authored
Rework misplaced reference taking on node structure Signed-off-by:
-
James Smart authored
Enhance debugfs to dump HBA SLIM as well as Host SLIM Signed-off-by:
-
James Smart authored
Fix Drivers Unsolicited CT command handling - we did not handle multiframe sequences well. Fix error due to delay in replenishing buffers for unsolicited data. Signed-off-by:
-
James Smart authored
Made link speed and link topology modifiable via sysfs Make scatter gather Segment Count into a module parameter. Signed-off-by:
-
Tomohiro Kusumi authored
This is a patch written by Tomohiro Kusumi and submitted to linux-scsi: http://marc.info/?l=linux-scsi&m=118673720712152&w=2 The original patch comment: This patch makes Emulex lpfc driver legacy I/O port free. It has already been acked quite long time ago. So I resubmit the patch. http://lkml.org/lkml/2006/11/22/28 Current lpfc driver is already using pci_select_bars() and pci_enable_device_bars() when the PCI bus has been reset. So I think this patch should also be acked. Signed-off-by:
Tomohiro Kusumi <kusumi.tomohiro@jp.fujitsu.com> Signed-off-by:
-
James Smart authored
Miscellaneous Fixes: - Fix a couple of sparse complaints - Reset the FCP recovery flag when the node is not a FCP2 device. - Speed up offline prep delays - Fixed a memory leak in lpfc_mem_alloc failure path - Fixed external loopback test. - Fixed error code returned from the driver when HBA is over heated. - Correct Max NPIV vport to limits read from adapter - Add missing locks around fc_flag and FC_NEEDS_REG_VPI - Add missing hba ids for device identification - Added support for SET_VARIABLE and MBX_WRITE_WWN mailbox commands - Changed all temperature event messages from warning to error - Fix reporting of link speed when link is down - Added support for MBX_WRITE_WWN mailbox command - Change del_timer_sync() in ISR to del_timer() in interrupt handler - Correct instances of beXX_to_cpu() that should be cpu_to_beXX() - Perform target flush before releasing node references on module unload - Avoid bogus devloss_tmo messages when driver unloads - Fix panic when HBA generates ERATT interupt - Fix mbox race condition and a workaround on back-to-back mailbox commands - Force NPIV off for pt2pt mode between 2 NPorts - Stop worker thread before removing fc_host. - Fix up discovery timeout error case due to missing clear_la - Tighten mailbox polling code to speed up detection of fast completions - Only allow DUMP_MEMORY if adapter offline due to overtemp errors - Added extended error information to the log messages in chip init. Signed-off-by:
-
James Smart authored
Add parameters to enable and disable heartbeat and hba resets Signed-off-by:
-
James Smart authored
Correct Abort handler logic. It was unconditionally waiting a minimum of 2 seconds rather than looking for abort completion. Signed-off-by:
-
James Smart authored
Miscellaneous Discovery/ELS Fixes: - Delay free's of ELS requests if adapter reject conditions - Fix concurrent PLOGI vs ADISC state handling - Add retry mechanism for GFF_ID - Correct some illegal state transitions around RSCN timeouts - Fix missing return in FAN handling Signed-off-by:
-
Salyzyn, Mark authored
The adapter queue is divided up equally to all the arrays to prevent command starvation to any individual array. On the other hand, physical targets are only granted a queue depth of one each. The code prior to this patch used to deal with the incremental discovery of targets, but the driver knows how many arrays are present prior to the scan so this knowledge is used to generate a better estimate for the queue depth. Remove the capability of 'physical=0' from preventing access to the class of adapters that have the RAID/SCSI mode of operation since none of the physicals on the SCSI channel are candidates ever for an array. As always, the user can override this default queue depth policy by making the appropriate adjustments utilizing sysfs. Signed-off-by:
-
Salyzyn, Mark authored
In experiments in the lab we managed to trigger an Adapter firmware panic (BlinkLED) coincidentally while several pass-through ioctl command from the management software were outstanding on a bug only present on a class of RAID Adapters that require a hardware reset rather than a commanded reset. The net result was an attempt to time out the management software command as if it came from the SCSI layer resulting in an OS panic. Adapters that use commanded reset, management commands are returned failed by the Adapter correctly. The adapter firmware panic that resulted in this condition was also resolved, and there were no adapters in the field with this specific firmware bug so we do not expect any field reports. This is a rare or unlikely corner condition, and no reports have ever been forwarded from the field. Signed-off-by:
-
Salyzyn, Mark authored
The 'entry' automatic variable was defined at the top and within a block that uses it, removed the definition from the block that uses it. Some cosmetic changes were made while in the same file. This patch should be inert. Signed-off-by:
-
Salyzyn, Mark authored
Big endian systems issues discovered in the aacraid driver. Somewhat reverses a patch from November 7th of last year that removed swap operations because they formerly were being assigned to an u8 array when they should have been assigned to an le32 array. This patch is largely inert for any little endian processor architecture. It resolves a bug in delivering the BlinkLED AIF event to registered applications when the adapter or associated hardware was reset due to ill health. A rare corner case occurrence, also largely unnoticed by any as it was a new (untested!) feature. Signed-off-by:
-
Salyzyn, Mark authored
The parameter 'info' is reused, renamed the second to sinfo to represent supplemental adapter info, to suppress compile warning message. Signed-off-by:
-
Salyzyn, Mark authored
Report the RAID level string for the SCSI device representing the array. Report is in /sys/class/scsi_device/#:#:#:#/device/level. Signed-off-by:
-
Salyzyn, Mark authored
aacraid.cache parameter, Disable Queue Flush commands: bit 0 - Disable FUA in WRITE SCSI commands bit 1 - Disable SYNCHRONIZE_CACHE SCSI command bit 2 - Disable only if Battery not protecting adapter supplied Cache e.g.: aacraid.cache=7 will disable the FUA and SYNCHRONIZE_CACHE commands if the adapter has reported that it's cache is battery backed up. This parameter permits experimentation with tradeoffs between performance and caching policy. Signed-off-by:
-
