QCA99X0 uses radio specific board names based on chip id and
board id combinations. We get these IDs from the target using BMI after otp.bin
has been started.

This patch reorders the call to the function ath10k_core_fetch_board_file
so that we have OTP binary before requesting for boardid-chipid. We get this
OTP data after parsing firmware-N.bin.

[kvalo@qca.qualcomm.com: try BMI_PARAM_GET_EEPROM_BOARD_ID with
 all boards and detect if command is not supported]
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

QCA6174 needs different board files based on board type. To make it easier to
distribute multiple board files and automatically choose correct board file
create a simple TLV file format following the same principles as with FW IEs.
The file is named board-2.bin and contain multiple board files. Each board file
then can have multiple names.

ath10k searches for file board-N.bin (where N is the interface version number
for the board file, just like we for firmware files) in /lib/firmware/*, for
example for qca99x0 it will try to find it here:

/lib/firmware/ath10k/QCA99X0/hw2.0/board-2.bin

If ath10k doesn't find board-2.bin then it will fallback to the old board.bin file.

This patch adds a simple name scheme using pci device id which for now will be
used by qca6174:

bus=%s,vendor=%04x,device=%04x,subsystem-vendor=%04x,subsystem-device=%04x

This removes the old method of having subsystem ids in ar->spec_board_id and
using that in the board file name.
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
[kvalo@qca.qualcomm.com: simplified the file format, rewrote commit log, other smaller changes]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

WARN_ON() already contain an unlikely compiler flag. Drop it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The DFS pattern detector ought to reset the
detector lines when a pulse is added with
lower time stamp than the previous (which
indicates a TSF restart).

This did not work so far and is fixed with
this patch.

The modification does not change detection
performance within the driver, since it
only ensures early reset (which is later
performed by the PRI detectors anyway).
It is relevant for synthetic tests and
statistical evaluations, where millions
of pulse patterns are processed and an
early reset helps reducing load.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The check for send_pkt being NULL is redundant before the call
to htc_reclaim_txctrl_buf, therefore it should be removed. This was
detected by static analysis by cppcheck.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

During reset flow, ignore firmware errors detected prior
to the actual hardware reset as the recovery flow would
make additional unnecessary reset.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

When firmware crashes, just before firmware recovery,
dump the firmware memory to a devcoredump device.
The resulting dump can be read from user space to be used
in offline crash analysis.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Situations observed when IP stack schedules lots of
frames for Tx while no connection (connection lost,
for example). In this case, dmesg bloated with error
message "FW not connected", printed for every frame.

Ratelimit this error message to avoid dmesg pollution.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

For the sniffer (monitor) mode, capture either control only or both
control and data PHY.

It used to be control only or data only PHY due to firmware
issues with configuration for PHY auto-detection; but now
it is resolved.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

BAR frames delivered to the host via Rx path; whole BAR frame
get delivered. Advance sequence in the reorder buffer and release
old frames, as per IEEE802.11 spec.

Firmware will reply to BAR, driver responsibility is only reorder
buffer management.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Hostapd request disconnect for broadcast bssid when it
wants to disconnect all stations from the AP.

Detect this and really disconnect all connected stations.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

When allocating pmc descriptor, the structure is
initially created on stack and later copied to
the physical ring (device) memory. The descriptor
structure must be initialized to zero to avoid
garbage configuration, which may result in pmc
mechanism malfunctioning.
Signed-off-by: Vladimir Shulman <QCA_shulmanv@QCA.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Print firmware and ucode assert codes when firmware crashed.
Signed-off-by: Lior David <liord@qti.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

On Rx, when invalid frame is received and dropped,
reaping of next frames from Rx ring is stopped.

This stops NAPI polling and re-enables the Rx interrupt.

However, in cases where no more frames received,
interrupt will not be triggered and rest of Rx frames
will not be processed.

Skip bad frames and continue to reap Rx packets when
such frames are encountered, and add statistics for
such frames for debug.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Fix compilation warning where CONFIG_PM defined while
CONFIG_PM_SLEEP is not defined

Report follows:

tree:   git://github.com/kvalo/ath pending
head:   941145fc5e5afbb120271e5dfaf37213ddb55807
commit: df596be39294d9712e5d568063a48448031e0a9f [37/39] wil6210: system power management
config: xtensa-allyesconfig (attached as .config)
reproduce:
  wget https://git.kernel.org/cgit/linux/kernel/git/wfg/lkp-tests.git/plain/sbin/make.cross -O ~/bin/make.cross
  chmod +x ~/bin/make.cross
  git checkout df596be39294d9712e5d568063a48448031e0a9f
  # save the attached .config to linux build tree
  make.cross ARCH=xtensa

All warnings (new ones prefixed by >>):

>> drivers/net/wireless/ath/wil6210/pcie_bus.c:264:12: warning: 'wil6210_suspend' defined but not used [-Wunused-function]
    static int wil6210_suspend(struct device *dev, bool is_runtime)
               ^
>> drivers/net/wireless/ath/wil6210/pcie_bus.c:291:12: warning: 'wil6210_resume' defined but not used [-Wunused-function]
    static int wil6210_resume(struct device *dev, bool is_runtime)
               ^
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The current number of spatial streams used by the client is advertised
as a separate IE in assoc request. Use this information to set
the NSS operating mode.

Fixes: 45c9abc0 ("ath10k: implement more versatile set_bitrate_mask").
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

After processing received packets from copy engine, host will allocate
new buffer and queue them back to copy engine ring for further
packet reception. On post rx processing path, skb allocation and
dma mapping are unnecessarily handled within ce_lock. This is affecting
peak throughput and also causing more CPU consumption. Optimize this
by acquiring ce_lock only when accessing copy engine ring and moving
skb allocation out of ce_lock.

In AP148 platform with QCA99x0 in conducted environment, UDP uplink peak
throughput is improved from ~1320 Mbps to ~1450 Mbps and TCP uplink peak
throughput is increased from ~1240 Mbps (70% host CPU load) to ~1300 Mbps
(71% CPU load). Similarly ~40Mbps improvement is observed in downlink
path.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

It is noticed that pci wakeup time is exceeding current timeout (10ms)
randomly which is tested on QCA988x. So, the wake up time is increased
to 30 ms and added debug prints to log total timeout.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k driver is using dma_pool_alloc per packet and dma_pool_free
in coresponding at Tx completion.
Use of pre-allocated DMA buffer in Tx will improve saving CPU resource
by 5% while it consumes about 56KB memory more as trade off.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k is using Native WiFi mode as default mode for both of
Tx and Rx path, but it could be changed when driver registers
with a module parameter for specific purpose such as mesh.

The Rx decap mode sent to firmware during WMI initialization should
use the same mode that driver configured at its registration stage
in case of using raw mode, so that host driver receives MAC frame
header containing necessary fields such as QoS and Mesh Control
and uses them in right way to make data traffic work.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The Transmit Power Control (TPC) dump will show the power control values for
each rate which makes it easier to debug calibration problems.

Example usage:

# cat /sys/kernel/debug/ieee80211/phy0/ath10k/tpc_stats
TPC config for channel  5180  mode  10

CTL             = 0x10 Reg. Domain              = 58
Antenna Gain    = 1    Reg. Max Antenna Gain    = 0
Power Limit     = 34   Reg. Max Power           = 34
Num tx chains   = 3    Num supported rates      = 155

**********CDD POWER TABLE*******

No.  Preamble Rate_code tpc_valu1 tpc_value2 tpc_value3
0       CCK     0x40       0            0       0
1       CCk     0x41       0            0       0

[...]

154     HTCUP   0x 0       24           0       0
**********STBC POWER TABLE******
No.  Preamble Rate_code tpc_valu1 tpc_value2 tpc_value3
0       CCK     0x40       0            0       0

[...]

154     HTCUP   0x 0       24           24      0
**********TXBF POWER TABLE******

is used to dump the tx power control stats.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Copy a_sle32_to_cpu() from ath6kl so that we can easily handle signed __le32
values. This is needed in struct wmi_pdev_tpc_config_event.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

from checkpatch:

drivers/net/wireless/ath/ath10k/mac.c:1113: line over 90 characters
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

checkpatch found:

drivers/net/wireless/ath/ath10k/core.c:574: Blank lines aren't necessary before a close brace '}'
drivers/net/wireless/ath/ath10k/mac.c:4067: Missing a blank line after declarations
drivers/net/wireless/ath/ath10k/mac.c:4083: Missing a blank line after declarations
drivers/net/wireless/ath/ath10k/mac.c:4084: spaces required around that '>>=' (ctx:WxV)
drivers/net/wireless/ath/ath10k/pci.c:1507: Missing a blank line after declarations
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

drivers/net/wireless/ath/ath10k/wmi.c:3023: void function return statements are not generally useful
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

drivers/net/wireless/ath/ath10k/htt_tx.c:457: braces {} are not necessary for single statement blocks
drivers/net/wireless/ath/ath10k/htt_tx.c:545: braces {} are not necessary for single statement blocks
drivers/net/wireless/ath/ath10k/mac.c:200: braces {} are not necessary for single statement blocks
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

checkpatch found:

drivers/net/wireless/ath/ath10k/core.c:513: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/core.c:1266: code indent should use tabs where possible
drivers/net/wireless/ath/ath10k/core.c:1267: code indent should use tabs where possible
drivers/net/wireless/ath/ath10k/core.c:1268: code indent should use tabs where possible
drivers/net/wireless/ath/ath10k/core.c:1269: code indent should use tabs where possible
drivers/net/wireless/ath/ath10k/mac.c:4659: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/mac.c:6271: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/pci.c:2260: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/wmi.c:3510: Alignment should match open parenthesis
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

checkpatch found:

drivers/net/wireless/ath/ath9k/core.c:490: Logical continuations should be on the previous line
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Major changes in ath10k:

* add spectral scan support for 10.4 firmware
* add qca6164 support
* implement mesh support using firmware raw mode

There were several bugs here.

1)  The done label was in the wrong place so we didn't copy any
    information out when there was no command given.

2)  We were using PAGE_SIZE as the size of the buffer instead of
    "PAGE_SIZE - pos".

3)  snprintf() returns the number of characters that would have been
    printed if there were enough space.  If there was not enough space
    (and we had fixed the memory corruption bug #2) then it would result
    in an information leak when we do simple_read_from_buffer().  I've
    changed it to use scnprintf() instead.

I also removed the initialization at the start of the function, because
I thought it made the code a little more clear.

Fixes: 5e6e3a92 ('wireless: mwifiex: initial commit for Marvell mwifiex driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add calls to netif_carrier_on and netif_carrier_off
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

IW_AUTH_ALG_OPEN_SYSTEM is ambiguous in set_auth for WEP as
wpa_supplicant uses it for both no encryption and WEP open system.
Cache the last mode set (only of these two) and use it here.

This allows wpa_supplicant to work with unencrypted APs.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

It's used locally only.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

It isn't used anywhere out of ssb code and we don't (plan to) build
pcihost_wrapper.c as a separated module.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

of_default_bus_match_table was not exported earlier, so it could only
be accessed by code compiled into the kernel. A new function
of_platform_default_populate() was added which uses
of_default_bus_match_table and this function is also exported. This way
it is possible to create a bus with the content of
of_default_bus_match_table and we can remove the hacks from bcma.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac uses atomic_or() and other atomic_* functions, but does not
include linux/atomic.h. This file gets included by some other header
file so this normally does not cause problems.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

TDLS events are mapped back to primary interface but when p2p is in
use then this fails because the check was incorrect by checking
bsscfg number. Which can be different when a p2p device has been
created.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

There is a workaround needed for p2p device setup which breaks tdls
functionality. This patch fixes that by properly signalling fweh that
p2p device setup is ongoing.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>