Now that all MDIO bus drivers which support C45 implement the c45
specific ops, remove the fallback to the old method.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Hayes Wang says:

====================
r8152: improve the code

These are some minor improvements depending on commit ec51fbd1 ("r8152:
add USB device driver for config selection").
====================

Link: https://lore.kernel.org/r/20230119074043.10021-397-nic_swsd@realtek.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Reduce the control transfer by moving calling rtl8152_get_version() in
rtl8152_probe(). This could prevent from calling rtl8152_get_version()
for unnecessary situations. For example, after setting config #2 for the
device, there are two interfaces and rtl8152_probe() may be called
twice. However, we don't need to call rtl8152_get_version() for this
situation.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

After commit ec51fbd1 ("r8152: add USB device driver for
config selection"), the code about changing USB configuration
in rtl_vendor_mode() wouldn't be run anymore. Therefore, the
function could be removed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

drivers/net/ipa/ipa_interrupt.c
drivers/net/ipa/ipa_interrupt.h
  9ec9b2a3 ("net: ipa: disable ipa interrupt during suspend")
  8e461e1f ("net: ipa: introduce ipa_interrupt_enable()")
  d50ed355 ("net: ipa: enable IPA interrupt handlers separate from registration")
https://lore.kernel.org/all/20230119114125.5182c7ab@canb.auug.org.au/
https://lore.kernel.org/all/79e46152-8043-a512-79d9-c3b905462774@tessares.net/Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Pull networking fixes from Jakub Kicinski:
 "Including fixes from wireless, bluetooth, bpf and netfilter.

  Current release - regressions:

   - Revert "net: team: use IFF_NO_ADDRCONF flag to prevent ipv6
     addrconf", fix nsna_ping mode of team

   - wifi: mt76: fix bugs in Rx queue handling and DMA mapping

   - eth: mlx5:
      - add missing mutex_unlock in error reporter
      - protect global IPsec ASO with a lock

  Current release - new code bugs:

   - rxrpc: fix wrong error return in rxrpc_connect_call()

  Previous releases - regressions:

   - bluetooth: hci_sync: fix use of HCI_OP_LE_READ_BUFFER_SIZE_V2

   - wifi:
      - mac80211: fix crashes on Rx due to incorrect initialization of
        rx->link and rx->link_sta
      - mac80211: fix bugs in iTXQ conversion - Tx stalls, incorrect
        aggregation handling, crashes
      - brcmfmac: fix regression for Broadcom PCIe wifi devices
      - rndis_wlan: prevent buffer overflow in rndis_query_oid

   - netfilter: conntrack: handle tcp challenge acks during connection
     reuse

   - sched: avoid grafting on htb_destroy_class_offload when destroying

   - virtio-net: correctly enable callback during start_xmit, fix stalls

   - tcp: avoid the lookup process failing to get sk in ehash table

   - ipa: disable ipa interrupt during suspend

   - eth: stmmac: enable all safety features by default

  Previous releases - always broken:

   - bpf:
      - fix pointer-leak due to insufficient speculative store bypass
        mitigation (Spectre v4)
      - skip task with pid=1 in send_signal_common() to avoid a splat
      - fix BPF program ID information in BPF_AUDIT_UNLOAD as well as
        PERF_BPF_EVENT_PROG_UNLOAD events
      - fix potential deadlock in htab_lock_bucket from same bucket
        index but different map_locked index

   - bluetooth:
      - fix a buffer overflow in mgmt_mesh_add()
      - hci_qca: fix driver shutdown on closed serdev
      - ISO: fix possible circular locking dependency
      - CIS: hci_event: fix invalid wait context

   - wifi: brcmfmac: fixes for survey dump handling

   - mptcp: explicitly specify sock family at subflow creation time

   - netfilter: nft_payload: incorrect arithmetics when fetching VLAN
     header bits

   - tcp: fix rate_app_limited to default to 1

   - l2tp: close all race conditions in l2tp_tunnel_register()

   - eth: mlx5: fixes for QoS config and eswitch configuration

   - eth: enetc: avoid deadlock in enetc_tx_onestep_tstamp()

   - eth: stmmac: fix invalid call to mdiobus_get_phy()

  Misc:

   - ethtool: add netlink attr in rss get reply only if the value is not
     empty"

* tag 'net-6.2-rc5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (88 commits)
  Revert "Merge branch 'octeontx2-af-CPT'"
  tcp: fix rate_app_limited to default to 1
  bnxt: Do not read past the end of test names
  net: stmmac: enable all safety features by default
  octeontx2-af: add mbox to return CPT_AF_FLT_INT info
  octeontx2-af: update cpt lf alloc mailbox
  octeontx2-af: restore rxc conf after teardown sequence
  octeontx2-af: optimize cpt pf identification
  octeontx2-af: modify FLR sequence for CPT
  octeontx2-af: add mbox for CPT LF reset
  octeontx2-af: recover CPT engine when it gets fault
  net: dsa: microchip: ksz9477: port map correction in ALU table entry register
  selftests/net: toeplitz: fix race on tpacket_v3 block close
  net/ulp: use consistent error code when blocking ULP
  octeontx2-pf: Fix the use of GFP_KERNEL in atomic context on rt
  tcp: avoid the lookup process failing to get sk in ehash table
  Revert "net: team: use IFF_NO_ADDRCONF flag to prevent ipv6 addrconf"
  MAINTAINERS: add networking entries for Willem
  net: sched: gred: prevent races when adding offloads to stats
  l2tp: prevent lockdep issue in l2tp_tunnel_register()
  ...

This reverts commit b4fbf0b2, reversing
changes made to 6c977c5c.

This seems like net-next material.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Srujana Challa says:

====================
octeontx2-af: Miscellaneous changes for CPT

This patchset consists of miscellaneous changes for CPT.
- Adds a new mailbox to reset the requested CPT LF.
- Modify FLR sequence as per HW team suggested.
- Adds support to recover CPT engines when they gets fault.
- Updates CPT inbound inline IPsec configuration mailbox,
  as per new generation of the OcteonTX2 chips.
- Adds a new mailbox to return CPT FLT Interrupt info.
====================

Link: https://lore.kernel.org/r/20230118120354.1017961-1-schalla@marvell.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

CPT HW would trigger the CPT AF FLT interrupt when CPT engines
hits some uncorrectable errors and AF is the one which receives
the interrupt and recovers the engines.
This patch adds a mailbox for CPT VFs to request for CPT faulted
and recovered engines info.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The CN10K CPT coprocessor contains a context processor
to accelerate updates to the IPsec security association
contexts. The context processor contains a context cache.
This patch updates CPT LF ALLOC mailbox to config ctx_ilen
requested by VFs. CPT_LF_ALLOC:ctx_ilen is the size of
initial context fetch.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

CN10K CPT coprocessor includes a component named RXC which
is responsible for reassembly of inner IP packets. RXC has
the feature to evict oldest entries based on age/threshold.
The age/threshold is being set to minimum values to evict
all entries at the time of teardown.
This patch adds code to restore timeout and threshold config
after teardown sequence is complete as it is global config.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Optimize CPT PF identification in mbox handling for faster
mbox response by doing it at AF driver probe instead of
every mbox message.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

On OcteonTX2 platform CPT instruction enqueue is only
possible via LMTST operations.
The existing FLR sequence mentioned in HRM requires
a dummy LMTST to CPT but LMTST can't be submitted from
AF driver. So, HW team provided a new sequence to avoid
dummy LMTST. This patch adds code for the same.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

On OcteonTX2 SoC, the admin function (AF) is the only one with all
priviliges to configure HW and alloc resources, PFs and it's VFs
have to request AF via mailbox for all their needs.
This patch adds a new mailbox for CPT VFs to request for CPT LF
reset.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When CPT engine has uncorrectable errors, it will get halted and
must be disabled and re-enabled. This patch adds code for the same.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Previously support for GNSS was implemented as a TTY driver, it allowed
to access GNSS receiver on /dev/ttyGNSS_<bus><func>.

Use generic GNSS subsystem API instead of implementing own TTY driver.
The receiver is accessible on /dev/gnss<id>. In case of multiple receivers
in the OS, correct device can be found by enumerating either:
- /sys/class/net/<eth port>/device/gnss/
- /sys/class/gnss/gnss<id>/device/

Using GNSS subsystem is superior to implementing own TTY driver, as the
GNSS subsystem was designed solely for this purpose. It also implements
TTY driver but in a common and defined way.

From user perspective, there is no difference in communicating with a
device, except new path to the device shall be used. The device will
provide same information to the userspace as the old one, and can be used
in the same way, i.e.:
old # gpsmon /dev/ttyGNSS_2100_0
new # gpsmon /dev/gnss0
There is no other impact on userspace tools.

User expecting onboard GNSS receiver support is required to enable
CONFIG_GNSS=y/m in kernel config.
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Michal Michalik <michal.michalik@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The acpi_evaluate_dsm_typed() provides a way to check the type of the
object evaluated by _DSM call. Use it instead of open coded variant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the ACPI part of a driver is optional the methods used in it
are expected to be available even if CONFIG_ACPI=n. This is not
the case for _DSM related methods. Add stubs for
acpi_evaluate_dsm_typed() and acpi_check_dsm() methods.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The initial default value of 0 for tp->rate_app_limited was incorrect,
since a flow is indeed application-limited until it first sends
data. Fixing the default to be 1 is generally correct but also
specifically will help user-space applications avoid using the initial
tcpi_delivery_rate value of 0 that persists until the connection has
some non-zero bandwidth sample.

Fixes: eb8329e0 ("tcp: export data delivery rate")
Suggested-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David Morley <morleyd@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Tested-by: David Morley <morleyd@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Test names were being concatenated based on a offset beyond the end of
the first name, which tripped the buffer overflow detection logic:

 detected buffer overflow in strnlen
 [...]
 Call Trace:
 bnxt_ethtool_init.cold+0x18/0x18

Refactor struct hwrm_selftest_qlist_output to use an actual array,
and adjust the concatenation to use snprintf() rather than a series of
strncat() calls.
Reported-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Link: https://lore.kernel.org/lkml/Y8F%2F1w1AZTvLglFX@x1-carbon/Tested-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Fixes: eb513658 ("bnxt_en: Add basic ethtool -t selftest support.")
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2023-01-19 (ice)

This series contains updates to ice driver only.

Tsotne and Anatolii implement new handling, and AdminQ command, for
firmware LLDP, adding a pending notification to allow for proper
cleanup between TC changes.

Amritha extends support for drop action outside of switchdev.

Siddaraju adjusts restriction for PTP HW clock adjustments.

Ani removes an unneeded non-null check and improves reporting of some link
modes to utilize more appropriate values.

Jesse adds checks to ensure PF VSI type.

Przemek combines duplicate checks of the same condition into one check.

Tony makes various cleanups to code: removes comments for cppcheck
suppressions, reduces scope of some variables, changes some return
statements to reflect an explicit 0 return, matches naming for function
declaration and definition, adds local variable for readability, and
fixes indenting.

Sergey separates DDP (Dynamic Device Personalization) code into its own
file.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Machon says:

====================
net: Introduce new DCB rewrite table

There is currently no support for per-port egress mapping of priority to PCP and
priority to DSCP. Some support for expressing egress mapping of PCP is supported
through ip link, with the 'egress-qos-map', however this command only maps
priority to PCP, and for vlan interfaces only. DCB APP already has support for
per-port ingress mapping of PCP/DEI, DSCP and a bunch of other stuff. So why not
take advantage of this fact, and add a new table that does the reverse.

This patch series introduces the new DCB rewrite table. Whereas the DCB
APP table deals with ingress mapping of PID (protocol identifier) to priority,
the rewrite table deals with egress mapping of priority to PID.

It is indeed possible to integrate rewrite in the existing APP table, by
introducing new dedicated rewrite selectors, and altering existing functions
to treat rewrite entries specially. However, I feel like this is not a good
solution, and will pollute the APP namespace. APP is well-defined in IEEE, and
some userspace relies of advertised entries - for this fact, separating APP and
rewrite into to completely separate objects, seems to me the best solution.

The new table shares much functionality with the APP table, and as such, much
existing code is reused, or slightly modified, to work for both.

================================================================================
DCB rewrite table in a nutshell
================================================================================
The table is implemented as a simple linked list, and uses the same lock as the
APP table. New functions for getting, setting and deleting entries have been
added, and these are exported, so they can be used by the stack or drivers.
Additionnaly, new dcbnl_setrewr and dcnl_delrewr hooks has been added, to
support hardware offload of the entries.

================================================================================
Sparx5 per-port PCP rewrite support
================================================================================
Sparx5 supports PCP egress mapping through two eight-entry switch tables.
One table maps QoS class 0-7 to PCP for DE0 (DP levels mapped to
drop-eligibility 0) and the other for DE1. DCB does currently not have support
for expressing DP/color, so instead, the tagged DEI bit will reflect the DP
levels, for any rewrite entries> 7 ('de').

The driver will take apptrust (contributed earlier) into consideration, so
that the mapping tables only be used, if PCP is trusted *and* the rewrite table
has active mappings, otherwise classified PCP (same as frame PCP) will be used
instead.

================================================================================
Sparx5 per-port DSCP rewrite support
================================================================================
Sparx5 support DSCP egress mapping through a single 32-entry table. This table
maps classified QoS class and DP level to classified DSCP, and is consulted by
the switch Analyzer Classifier at ingress. At egress, the frame DSCP can either
be rewritten to classified DSCP to frame DSCP.

The driver will take apptrust into consideration, so that the mapping tables
only be used, if DSCP is trusted *and* the rewrite table has active mappings,
otherwise frame DSCP will be used instead.

================================================================================
Patches
================================================================================
Patch #1 modifies dcb_app_add to work for both APP and rewrite

Patch #2 adds dcbnl_app_table_setdel() for setting and deleting both APP and
         rewrite entries.

Patch #3 adds the rewrite table and all required functions, offload hooks and
         bookkeeping for maintaining it.

Patch #4 adds two new helper functions for getting a priority to PCP bitmask
         map, and a priority to DSCP bitmask map.

Patch #5 adds support for PCP rewrite in the Sparx5 driver.
Patch #6 adds support for DSCP rewrite in the Sparx5 driver.

================================================================================
v2 -> v3:
  in dcbnl_ieee_fill() use nla_nest_start() instead of the _noflag() version.
  Also, cancel the rewrite nest in case of an error (Petr Machata).

v1 -> v2:
  In dcb_setrewr() change proto to u16 as it ought to be, and remove zero
  initialization of err. (Dan Carpenter).
  Change name of dcbnl_apprewr_setdel -> dcbnl_app_table_setdel and change the
  function signature to take a single function pointer. Update uses accordingly
  (Petr Machata).

====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for DSCP rewrite in Sparx5 driver. On egress DSCP is
rewritten from either classified DSCP, or frame DSCP. Classified DSCP is
determined by the Analyzer Classifier on ingress, and is mapped from
classified QoS class and DP level. Classification of DSCP is by default
enabled for all ports.

It is required that DSCP is trusted for the egress port *and* rewrite
table is not empty, in order to rewrite DSCP based on classified DSCP,
otherwise DSCP is always rewritten from frame DSCP.

classified_dscp = qos_dscp_map[8 * dp_level + qos_class];
if (active_mappings && dscp_is_trusted)
	rewritten_dscp = classified_dscp
else
	rewritten_dscp = frame_dscp

To rewrite DSCP to 20 for any frames with priority 7:

$ dcb apptrust set dev eth0 order dscp
$ dcb rewr add dev eth0 7:20 <-- not in iproute2/dcb yet
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for rewrite of PCP and DEI, based on classified Quality of
Service (QoS) class and Drop-Precedence (DP) level.

The DCB rewrite table is queried for mappings between priority and
PCP/DEI. The classified DP level is then encoded in the DEI bit, if a
mapping for DEI exists.

Sparx5 has four DP levels, where by default, 0 is mapped to DE0 and 1-3
are mapped to DE1. If a mapping exists where DEI=1, then all classified
DP levels mapped to DE1 will set the DEI bit. The other way around for
DEI=0. Effectively, this means that the tagged DEI bit will reflect the
DP level for any mappings where DEI=1.

Map priority=1 to PCP=1 and DEI=1:
$ dcb rewr add dev eth0 pcp-prio 1:1de

Map priority=7 to PCP=2 and DEI=0
$ dcb rewr add dev eth0 pcp-prio 7:2nd

Also, sparx5_dcb_ieee_dscp_setdel() has been refactored, to work for
both APP and rewrite entries.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add two new helper functions to retrieve a mapping of priority to PCP
and DSCP bitmasks, where each bitmap contains ones in positions that
match a rewrite entry.

dcb_ieee_getrewr_prio_dscp_mask_map() reuses the dcb_ieee_app_prio_map,
as this struct is already used for a similar mapping in the app table.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add new rewrite table and all the required functions, offload hooks and
bookkeeping for maintaining it. The rewrite table reuses the app struct,
and the entire set of app selectors. As such, some bookeeping code can
be shared between the rewrite- and the APP table.

New functions for getting, setting and deleting entries has been added.
Apart from operating on the rewrite list, these functions do not emit a
DCB_APP_EVENT when the list os modified. The new dcb_getrewr does a
lookup based on selector and priority and returns the protocol, so that
mappings from priority to protocol, for a given selector and ifindex is
obtained.

Also, a new nested attribute has been added, that encapsulates one or
more app structs. This attribute is used to distinguish the two tables.

The dcb_lock used for the APP table is reused for the rewrite table.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for DCB rewrite. Add a new function for setting and
deleting both app and rewrite entries. Moving this into a separate
function reduces duplicate code, as both type of entries requires the
same set of checks. The function will now iterate through a configurable
nested attribute (app or rewrite attr), validate each attribute and call
the appropriate set- or delete function.

Note that this function always checks for nla_len(attr_itr) <
sizeof(struct dcb_app), which was only done in dcbnl_ieee_set and not in
dcbnl_ieee_del prior to this patch. This means, that any userspace tool
that used to shove in data < sizeof(struct dcb_app) would now receive
-ERANGE.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation to DCB rewrite. Modify dcb_app_add to take new struct
list_head * as parameter, to make the used list configurable. This is
done to allow reusing the function for adding rewrite entries to the
rewrite table, which is introduced in a later patch.
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the original implementation of dwmac5
commit 8bf993a5 ("net: stmmac: Add support for DWMAC5 and implement Safety Features")
all safety features were enabled by default.

Later it seems some implementations didn't have support for all the
features, so in
commit 5ac712dc ("net: stmmac: enable platform specific safety features")
the safety_feat_cfg structure was added to the callback and defined for
some platforms to selectively enable these safety features.

The problem is that only certain platforms were given that software
support. If the automotive safety package bit is set in the hardware
features register the safety feature callback is called for the platform,
and for platforms that didn't get a safety_feat_cfg defined this results
in the following NULL pointer dereference:

[    7.933303] Call trace:
[    7.935812]  dwmac5_safety_feat_config+0x20/0x170 [stmmac]
[    7.941455]  __stmmac_open+0x16c/0x474 [stmmac]
[    7.946117]  stmmac_open+0x38/0x70 [stmmac]
[    7.950414]  __dev_open+0x100/0x1dc
[    7.954006]  __dev_change_flags+0x18c/0x204
[    7.958297]  dev_change_flags+0x24/0x6c
[    7.962237]  do_setlink+0x2b8/0xfa4
[    7.965827]  __rtnl_newlink+0x4ec/0x840
[    7.969766]  rtnl_newlink+0x50/0x80
[    7.973353]  rtnetlink_rcv_msg+0x12c/0x374
[    7.977557]  netlink_rcv_skb+0x5c/0x130
[    7.981500]  rtnetlink_rcv+0x18/0x2c
[    7.985172]  netlink_unicast+0x2e8/0x340
[    7.989197]  netlink_sendmsg+0x1a8/0x420
[    7.993222]  ____sys_sendmsg+0x218/0x280
[    7.997249]  ___sys_sendmsg+0xac/0x100
[    8.001103]  __sys_sendmsg+0x84/0xe0
[    8.004776]  __arm64_sys_sendmsg+0x24/0x30
[    8.008983]  invoke_syscall+0x48/0x114
[    8.012840]  el0_svc_common.constprop.0+0xcc/0xec
[    8.017665]  do_el0_svc+0x38/0xb0
[    8.021071]  el0_svc+0x2c/0x84
[    8.024212]  el0t_64_sync_handler+0xf4/0x120
[    8.028598]  el0t_64_sync+0x190/0x194

Go back to the original behavior, if the automotive safety package
is found to be supported in hardware enable all the features unless
safety_feat_cfg is passed in saying this particular platform only
supports a subset of the features.

Fixes: 5ac712dc ("net: stmmac: enable platform specific safety features")
Reported-by: Ning Cai <ncai@quicinc.com>
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Srujana Challa says:

====================
octeontx2-af: Miscellaneous changes for CPT

This patchset consists of miscellaneous changes for CPT.
- Adds a new mailbox to reset the requested CPT LF.
- Modify FLR sequence as per HW team suggested.
- Adds support to recover CPT engines when they gets fault.
- Updates CPT inbound inline IPsec configuration mailbox,
  as per new generation of the OcteonTX2 chips.
- Adds a new mailbox to return CPT FLT Interrupt info.

---
v2:
- Addressed a review comment.
v1:
- Dropped patch "octeontx2-af: Fix interrupt name strings completely"
  to submit to net.
---
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

CPT HW would trigger the CPT AF FLT interrupt when CPT engines
hits some uncorrectable errors and AF is the one which receives
the interrupt and recovers the engines.
This patch adds a mailbox for CPT VFs to request for CPT faulted
and recovered engines info.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The CN10K CPT coprocessor contains a context processor
to accelerate updates to the IPsec security association
contexts. The context processor contains a context cache.
This patch updates CPT LF ALLOC mailbox to config ctx_ilen
requested by VFs. CPT_LF_ALLOC:ctx_ilen is the size of
initial context fetch.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

CN10K CPT coprocessor includes a component named RXC which
is responsible for reassembly of inner IP packets. RXC has
the feature to evict oldest entries based on age/threshold.
The age/threshold is being set to minimum values to evict
all entries at the time of teardown.
This patch adds code to restore timeout and threshold config
after teardown sequence is complete as it is global config.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Optimize CPT PF identification in mbox handling for faster
mbox response by doing it at AF driver probe instead of
every mbox message.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On OcteonTX2 platform CPT instruction enqueue is only
possible via LMTST operations.
The existing FLR sequence mentioned in HRM requires
a dummy LMTST to CPT but LMTST can't be submitted from
AF driver. So, HW team provided a new sequence to avoid
dummy LMTST. This patch adds code for the same.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On OcteonTX2 SoC, the admin function (AF) is the only one with all
priviliges to configure HW and alloc resources, PFs and it's VFs
have to request AF via mailbox for all their needs.
This patch adds a new mailbox for CPT VFs to request for CPT LF
reset.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When CPT engine has uncorrectable errors, it will get halted and
must be disabled and re-enabled. This patch adds code for the same.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jerry Ray says:

====================
dsa: lan9303: Move to PHYLINK

This patch series moves the lan9303 driver to use the phylink
api away from phylib.

Migrating to phylink means removing the .adjust_link api. The
functionality from the adjust_link is moved to the phylink_mac_link_up
api.  The code being removed only affected the cpu port.  The other
ports on the LAN9303 do not need anything from the phylink_mac_link_up
api.

Patches:
 0001 - Whitespace only change aligning the dsa_switch_ops members.
	No code changes.
 0002 - Moves the Turbo bit initialization out of the adjust_link api and
	places it in a driver initialization execution path. It only needs
	to be initialized once, it is never changed, and it is not a
	per-port flag.
 0003 - Adds exception handling logic in the extremely unlikely event that
	the read of the device fails.
 0004 - Performance optimization that skips a slow register write if there
	is no need to perform it.
 0005 - Change the way we identify the xMII port as phydev will be NULL
	when this logic is moved into phylink_mac_link_up.
 0006 - Removes adjust_link and begins using the phylink dsa_switch_ops
	apis.
 0007 - Adds XMII port flow control settings in the phylink_mac_link_up()
	api while cleaning up the ANEG / speed / duplex implementation.
---
v6->v7:
  - Moved the initialization of the Turbo bit into lan9303_setup().
  - Added a macro for determining is a port is an XMII port.
  - Added setting the XMII flow control in the phylink_mac_link_up() API.
  - removed unnecessary error handling and cleaned up the code flow in
    phylink_mac_link_up().
v5->v6:
  - Moved to using port number to identify xMII port for the LAN9303.
v4->v5:
  - Created prep patches to better show how things migrate.
  - cleaned up comments.
v3->v4:
  - Addressed whitespace issues as a separate patch.
  - Removed port_max_mtu api patch as it is unrelated to phylink migration.
  - Reworked the implementation to preserve the adjust_link functionality
    by including it in the phylink_mac_link_up api.
v2->v3:
  Added back in disabling Turbo Mode on the CPU MII interface.
  Removed the unnecessary clearing of the phy supported interfaces.
v1->v2:
  corrected the reported mtu size, removing ETH_HLEN and ETH_FCS_LEN
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

While the prior patch moved the adjust_link code into the
phylink_mac_link_up api, this patch cleans it up and adds the setting the
port's flow control based on the phylink_mac_link_up input parameters.
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch replaces the adjust_link api with the phylink apis that provide
equivalent functionality.

The remaining functionality from the adjust_link is now covered in the
phylink_mac_link_up api.

Removes:
.adjust_link
Adds:
.phylink_get_caps
.phylink_mac_link_up
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>