- 02 Feb, 2015 40 commits
-
-
Ben Hutchings authored
commit 0e6d3112 upstream. It is currently possible to execve() an x32 executable on an x86_64 kernel that has only ia32 compat enabled. However all its syscalls will fail, even _exit(). This usually causes it to segfault. Change the ELF compat architecture check so that x32 executables are rejected if we don't support the x32 ABI. Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Link: http://lkml.kernel.org/r/1410120305.6822.9.camel@decadent.org.ukSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
Zefan Li <lizefan@huawei.com>
-
Scott Carter authored
commit 37017ac6 upstream. The Broadcom OSB4 IDE Controller (vendor and device IDs: 1166:0211) does not support 64-KB DMA transfers. Whenever a 64-KB DMA transfer is attempted, the transfer fails and messages similar to the following are written to the console log: [ 2431.851125] sr 0:0:0:0: [sr0] Unhandled sense code [ 2431.851139] sr 0:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 2431.851152] sr 0:0:0:0: [sr0] Sense Key : Hardware Error [current] [ 2431.851166] sr 0:0:0:0: [sr0] Add. Sense: Logical unit communication time-out [ 2431.851182] sr 0:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 76 f4 00 00 40 00 [ 2431.851210] end_request: I/O error, dev sr0, sector 121808 When the libata and pata_serverworks modules are recompiled with ATA_DEBUG and ATA_VERBOSE_DEBUG defined in libata.h, the 64-KB transfer size in the scatter-gather list can be seen in the console log: [ 2664.897267] sr 9:0:0:0: [sr0] Send: [ 2664.897274] 0xf63d85e0 [ 2664.897283] sr 9:0:0:0: [sr0] CDB: [ 2664.897288] Read(10): 28 00 00 00 7f b4 00 00 40 00 [ 2664.897319] buffer = 0xf6d6fbc0, bufflen = 131072, queuecommand 0xf81b7700 [ 2664.897331] ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 00 00 7f b4 00 00 40 [ 2664.897338] ata_scsi_translate: ENTER [ 2664.897345] ata_sg_setup: ENTER, ata1 [ 2664.897356] ata_sg_setup: 3 sg elements mapped [ 2664.897364] ata_bmdma_fill_sg: PRD[0] = (0x66FD2000, 0xE000) [ 2664.897371] ata_bmdma_fill_sg: PRD[1] = (0x65000000, 0x10000) ------------------------------------------------------> ======= [ 2664.897378] ata_bmdma_fill_sg: PRD[2] = (0x66A10000, 0x2000) [ 2664.897386] ata1: ata_dev_select: ENTER, device 0, wait 1 [ 2664.897422] ata_sff_tf_load: feat 0x1 nsect 0x0 lba 0x0 0x0 0xFC [ 2664.897428] ata_sff_tf_load: device 0xA0 [ 2664.897448] ata_sff_exec_command: ata1: cmd 0xA0 [ 2664.897457] ata_scsi_translate: EXIT [ 2664.897462] leaving scsi_dispatch_cmnd() [ 2664.897497] Doing sr request, dev = sr0, block = 0 [ 2664.897507] sr0 : reading 64/256 512 byte blocks. [ 2664.897553] ata_sff_hsm_move: ata1: protocol 7 task_state 1 (dev_stat 0x58) [ 2664.897560] atapi_send_cdb: send cdb [ 2666.910058] ata_bmdma_port_intr: ata1: host_stat 0x64 [ 2666.910079] __ata_sff_port_intr: ata1: protocol 7 task_state 3 [ 2666.910093] ata_sff_hsm_move: ata1: protocol 7 task_state 3 (dev_stat 0x51) [ 2666.910101] ata_sff_hsm_move: ata1: protocol 7 task_state 4 (dev_stat 0x51) [ 2666.910129] sr 9:0:0:0: [sr0] Done: [ 2666.910136] 0xf63d85e0 TIMEOUT lspci shows that the driver used for the Broadcom OSB4 IDE Controller is pata_serverworks: 00:0f.1 IDE interface: Broadcom OSB4 IDE Controller (prog-if 8e [Master SecP SecO PriP]) Flags: bus master, medium devsel, latency 64 [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8] [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1] I/O ports at 0170 [size=8] I/O ports at 0374 [size=4] I/O ports at 1440 [size=16] Kernel driver in use: pata_serverworks The pata_serverworks driver supports five distinct device IDs, one being the OSB4 and the other four belonging to the CSB series. The CSB series appears to support 64-KB DMA transfers, as tests on a machine with an SAI2 motherboard containing a Broadcom CSB5 IDE Controller (vendor and device IDs: 1166:0212) showed no problems with 64-KB DMA transfers. This problem was first discovered when attempting to install openSUSE from a DVD on a machine with an STL2 motherboard. Using the pata_serverworks module, older releases of openSUSE will not install at all due to the timeouts. Releases of openSUSE prior to 11.3 can be installed by disabling the pata_serverworks module using the brokenmodules boot parameter, which causes the serverworks module to be used instead. Recent releases of openSUSE (12.2 and later) include better error recovery and will install, though very slowly. On all openSUSE releases, the problem can be recreated on a machine containing a Broadcom OSB4 IDE Controller by mounting an install DVD and running a command similar to the following: find /mnt -type f -print | xargs cat > /dev/null The patch below corrects the problem. Similar to the other ATA drivers that do not support 64-KB DMA transfers, the patch changes the ata_port_operations qc_prep vector to point to a routine that breaks any 64-KB segment into two 32-KB segments and changes the scsi_host_template sg_tablesize element to reduce by half the number of scatter/gather elements allowed. These two changes affect only the OSB4. Signed-off-by:
Scott Carter <ccscott@funsoft.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Chao Yu authored
commit 35425ea2 upstream. Christopher Head 2014-06-28 05:26:20 UTC described: "I tried to reproduce this on 3.12.21. Instead, when I do "echo hello > foo" in an ecryptfs mount with ecryptfs_xattr specified, I get a kernel crash: BUG: unable to handle kernel NULL pointer dereference at (null) IP: [<ffffffff8110eb39>] fsstack_copy_attr_all+0x2/0x61 PGD d7840067 PUD b2c3c067 PMD 0 Oops: 0002 [#1] SMP Modules linked in: nvidia(PO) CPU: 3 PID: 3566 Comm: bash Tainted: P O 3.12.21-gentoo-r1 #2 Hardware name: ASUSTek Computer Inc. G60JX/G60JX, BIOS 206 03/15/2010 task: ffff8801948944c0 ti: ffff8800bad70000 task.ti: ffff8800bad70000 RIP: 0010:[<ffffffff8110eb39>] [<ffffffff8110eb39>] fsstack_copy_attr_all+0x2/0x61 RSP: 0018:ffff8800bad71c10 EFLAGS: 00010246 RAX: 00000000000181a4 RBX: ffff880198648480 RCX: 0000000000000000 RDX: 0000000000000004 RSI: ffff880172010450 RDI: 0000000000000000 RBP: ffff880198490e40 R08: 0000000000000000 R09: 0000000000000000 R10: ffff880172010450 R11: ffffea0002c51e80 R12: 0000000000002000 R13: 000000000000001a R14: 0000000000000000 R15: ffff880198490e40 FS: 00007ff224caa700(0000) GS:ffff88019fcc0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 00000000bb07f000 CR4: 00000000000007e0 Stack: ffffffff811826e8 ffff8800a39d8000 0000000000000000 000000000000001a ffff8800a01d0000 ffff8800a39d8000 ffffffff81185fd5 ffffffff81082c2c 00000001a39d8000 53d0abbc98490e40 0000000000000037 ffff8800a39d8220 Call Trace: [<ffffffff811826e8>] ? ecryptfs_setxattr+0x40/0x52 [<ffffffff81185fd5>] ? ecryptfs_write_metadata+0x1b3/0x223 [<ffffffff81082c2c>] ? should_resched+0x5/0x23 [<ffffffff8118322b>] ? ecryptfs_initialize_file+0xaf/0xd4 [<ffffffff81183344>] ? ecryptfs_create+0xf4/0x142 [<ffffffff810f8c0d>] ? vfs_create+0x48/0x71 [<ffffffff810f9c86>] ? do_last.isra.68+0x559/0x952 [<ffffffff810f7ce7>] ? link_path_walk+0xbd/0x458 [<ffffffff810fa2a3>] ? path_openat+0x224/0x472 [<ffffffff810fa7bd>] ? do_filp_open+0x2b/0x6f [<ffffffff81103606>] ? __alloc_fd+0xd6/0xe7 [<ffffffff810ee6ab>] ? do_sys_open+0x65/0xe9 [<ffffffff8157d022>] ? system_call_fastpath+0x16/0x1b RIP [<ffffffff8110eb39>] fsstack_copy_attr_all+0x2/0x61 RSP <ffff8800bad71c10> CR2: 0000000000000000 ---[ end trace df9dba5f1ddb8565 ]---" If we create a file when we mount with ecryptfs_xattr_metadata option, we will encounter a crash in this path: ->ecryptfs_create ->ecryptfs_initialize_file ->ecryptfs_write_metadata ->ecryptfs_write_metadata_to_xattr ->ecryptfs_setxattr ->fsstack_copy_attr_all It's because our dentry->d_inode used in fsstack_copy_attr_all is NULL, and it will be initialized when ecryptfs_initialize_file finish. So we should skip copying attr from lower inode when the value of ->d_inode is invalid. Signed-off-by:
Chao Yu <chao2.yu@samsung.com> Signed-off-by:
Tyler Hicks <tyhicks@canonical.com> Signed-off-by:
-
Alexey Khoroshilov authored
commit 56ec16cb upstream. If cn_add_callback() fails in dm_ulog_tfr_init(), it does not deallocate prealloced memory but calls cn_del_callback(). Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Reviewed-by:
Jonathan Brassow <jbrassow@redhat.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Joe Thornber authored
commit eb76faf5 upstream. The 'last_accessed' member of the dm_buffer structure was only set when the the buffer was created. This led to each buffer being discarded after dm_bufio_max_age time even if it was used recently. In practice this resulted in all thinp metadata being evicted soon after being read -- this is particularly problematic for metadata intensive workloads like multithreaded small random IO. 'last_accessed' is now updated each time the buffer is moved to the head of the LRU list, so the buffer is now properly discarded if it was not used in dm_bufio_max_age time. Signed-off-by:
Joe Thornber <ejt@redhat.com> Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
-
Geert Uytterhoeven authored
commit e4dc601b upstream. hwreg_present() and hwreg_write() temporarily change the VBR register to another vector table. This table contains a valid bus error handler only, all other entries point to arbitrary addresses. If an interrupt comes in while the temporary table is active, the processor will start executing at such an arbitrary address, and the kernel will crash. While most callers run early, before interrupts are enabled, or explicitly disable interrupts, Finn Thain pointed out that macsonic has one callsite that doesn't, causing intermittent boot crashes. There's another unsafe callsite in hilkbd. Fix this for good by disabling and restoring interrupts inside hwreg_present() and hwreg_write(). Explicitly disabling interrupts can be removed from the callsites later. Reported-by:
Finn Thain <fthain@telegraphics.com.au> Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
-
Andy Adamson authored
commit d1f456b0 upstream. Commit 2f60ea6b ("NFSv4: The NFSv4.0 client must send RENEW calls if it holds a delegation") set the NFS4_RENEW_TIMEOUT flag in nfs4_renew_state, and does not put an nfs41_proc_async_sequence call, the NFSv4.1 lease renewal heartbeat call, on the wire to renew the NFSv4.1 state if the flag was not set. The NFS4_RENEW_TIMEOUT flag is set when "now" is after the last renewal (cl_last_renewal) plus the lease time divided by 3. This is arbitrary and sometimes does the following: In normal operation, the only way a future state renewal call is put on the wire is via a call to nfs4_schedule_state_renewal, which schedules a nfs4_renew_state workqueue task. nfs4_renew_state determines if the NFS4_RENEW_TIMEOUT should be set, and the calls nfs41_proc_async_sequence, which only gets sent if the NFS4_RENEW_TIMEOUT flag is set. Then the nfs41_proc_async_sequence rpc_release function schedules another state remewal via nfs4_schedule_state_renewal. Without this change we can get into a state where an application stops accessing the NFSv4.1 share, state renewal calls stop due to the NFS4_RENEW_TIMEOUT flag _not_ being set. The only way to recover from this situation is with a clientid re-establishment, once the application resumes and the server has timed out the lease and so returns NFS4ERR_BAD_SESSION on the subsequent SEQUENCE operation. An example application: open, lock, write a file. sleep for 6 * lease (could be less) ulock, close. In the above example with NFSv4.1 delegations enabled, without this change, there are no OP_SEQUENCE state renewal calls during the sleep, and the clientid is recovered due to lease expiration on the close. This issue does not occur with NFSv4.1 delegations disabled, nor with NFSv4.0, with or without delegations enabled. Signed-off-by:
Andy Adamson <andros@netapp.com> Link: http://lkml.kernel.org/r/1411486536-23401-1-git-send-email-andros@netapp.com Fixes: 2f60ea6b (NFSv4: The NFSv4.0 client must send RENEW calls...) Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> [lizf: Backported to 3.4: adjust context] Signed-off-by:
-
Borislav Petkov authored
commit a18c3f16 upstream. The other two interrupt handlers in this driver are shared, except this one. When loading the driver, it fails like this. So make the IRQ line shared. Freescale(R) MPC85xx EDAC driver, (C) 2006 Montavista Software mpc85xx_mc_err_probe: No ECC DIMMs discovered EDAC DEVICE0: Giving out device to module MPC85xx_edac controller mpc85xx_l2_err: DEV mpc85xx_l2_err (INTERRUPT) genirq: Flags mismatch irq 16. 00000000 ([EDAC] L2 err) vs. 00000080 ([EDAC] PCI err) mpc85xx_l2_err_probe: Unable to request irq 16 for MPC85xx L2 err remove_proc_entry: removing non-empty directory 'irq/16', leaking at least 'aerdrv' ------------[ cut here ]------------ WARNING: at fs/proc/generic.c:521 Modules linked in: CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.17.0-rc5-dirty #1 task: ee058000 ti: ee046000 task.ti: ee046000 NIP: c016c0c4 LR: c016c0c4 CTR: c037b51c REGS: ee047c10 TRAP: 0700 Not tainted (3.17.0-rc5-dirty) MSR: 00029000 <CE,EE,ME> CR: 22008022 XER: 20000000 GPR00: c016c0c4 ee047cc0 ee058000 00000053 00029000 00000000 c037c744 00000003 GPR08: c09aab28 c09aab24 c09aab28 00000156 20008028 00000000 c0002ac8 00000000 GPR16: 00000000 00000000 00000000 00000000 00000000 00000000 00000139 c0950394 GPR24: c09f0000 ee5585b0 ee047d08 c0a10000 ee047d08 ee15f808 00000002 ee03f660 NIP [c016c0c4] remove_proc_entry LR [c016c0c4] remove_proc_entry Call Trace: remove_proc_entry (unreliable) unregister_irq_proc free_desc irq_free_descs mpc85xx_l2_err_probe platform_drv_probe really_probe __driver_attach bus_for_each_dev bus_add_driver driver_register mpc85xx_mc_init do_one_initcall kernel_init_freeable kernel_init ret_from_kernel_thread Instruction dump: ... Reported-and-tested-by: <lpb_098@163.com> Acked-by:
Johannes Thumshirn <johannes.thumshirn@men.de> Signed-off-by:
Borislav Petkov <bp@suse.de> [lizf: Backported to 3.4: IRQF_DISABLED hasn't been removed in 3.4] Signed-off-by:
-
Mikulas Patocka authored
commit f74a289b upstream. The framebuffer code uses the current background color to fill the border when switching consoles, however, this results in inconsistent behavior. For example: - start Midnigh Commander - the border is black - switch to another console and switch back - the border is cyan - type something into the command line in mc - the border is cyan - switch to another console and switch back - the border is black - press F9 to go to menu - the border is black - switch to another console and switch back - the border is dark blue When switching to a console with Midnight Commander, the border is random color that was left selected by the slang subsystem. This patch fixes this inconsistency by always using black as the background color when switching consoles. Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by:
-
Bryan O'Donoghue authored
commit 1ede7dcc upstream. Quark X1000 contains two designware derived 8250 serial ports. Each port has a unique PCI configuration space consisting of BAR0:UART BAR1:DMA respectively. Unlike the standard 8250 the register width is 32 bits for RHR,IER etc The Quark UART has a fundamental clock @ 44.2368 MHz allowing for a bitrate of up to about 2.76 megabits per second. This patch enables standard 8250 mode Signed-off-by:
Bryan O'Donoghue <pure.logic@nexus-software.ie> Reviewed-by:
Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> [lizf: Backported to 3.4: adjust context] Signed-off-by:
-
Trond Myklebust authored
commit df817ba3 upstream. The current open/lock state recovery unfortunately does not handle errors such as NFS4ERR_CONN_NOT_BOUND_TO_SESSION correctly. Instead of looping, just proceeds as if the state manager is finished recovering. This patch ensures that we loop back, handle higher priority errors and complete the open/lock state recovery. Signed-off-by:
-
Ondrej Zary authored
commit 6d8ca28f upstream. Currently, ata_sff_softreset is skipped for controllers with no ctl port. But that also skips ata_sff_dev_classify required for device detection. This means that libata is currently broken on controllers with no ctl port. No device connected: [ 1.872480] pata_isapnp 01:01.02: activated [ 1.889823] scsi2 : pata_isapnp [ 1.890109] ata3: PATA max PIO0 cmd 0x1e8 ctl 0x0 irq 11 [ 6.888110] ata3.01: qc timeout (cmd 0xec) [ 6.888179] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5) [ 16.888085] ata3.01: qc timeout (cmd 0xec) [ 16.888147] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5) [ 46.888086] ata3.01: qc timeout (cmd 0xec) [ 46.888148] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5) [ 51.888100] ata3.00: qc timeout (cmd 0xec) [ 51.888160] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x5) [ 61.888079] ata3.00: qc timeout (cmd 0xec) [ 61.888141] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x5) [ 91.888089] ata3.00: qc timeout (cmd 0xec) [ 91.888152] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x5) ATAPI device connected: [ 1.882061] pata_isapnp 01:01.02: activated [ 1.893430] scsi2 : pata_isapnp [ 1.893719] ata3: PATA max PIO0 cmd 0x1e8 ctl 0x0 irq 11 [ 6.892107] ata3.01: qc timeout (cmd 0xec) [ 6.892171] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5) [ 16.892079] ata3.01: qc timeout (cmd 0xec) [ 16.892138] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5) [ 46.892079] ata3.01: qc timeout (cmd 0xec) [ 46.892138] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5) [ 46.908586] ata3.00: ATAPI: ACER CD-767E/O, V1.5X, max PIO2, CDB intr [ 46.924570] ata3.00: configured for PIO0 (device error ignored) [ 46.926295] scsi 2:0:0:0: CD-ROM ACER CD-767E/O 1.5X PQ: 0 ANSI: 5 [ 46.984519] sr0: scsi3-mmc drive: 6x/6x xa/form2 tray [ 46.984592] cdrom: Uniform CD-ROM driver Revision: 3.20 So don't skip ata_sff_softreset, just skip the reset part of ata_bus_softreset if the ctl port is not available. This makes IDE port on ES968 behave correctly: No device connected: [ 4.670888] pata_isapnp 01:01.02: activated [ 4.673207] scsi host2: pata_isapnp [ 4.673675] ata3: PATA max PIO0 cmd 0x1e8 ctl 0x0 irq 11 [ 7.081840] Adding 2541652k swap on /dev/sda2. Priority:-1 extents:1 across:2541652k ATAPI device connected: [ 4.704362] pata_isapnp 01:01.02: activated [ 4.706620] scsi host2: pata_isapnp [ 4.706877] ata3: PATA max PIO0 cmd 0x1e8 ctl 0x0 irq 11 [ 4.872782] ata3.00: ATAPI: ACER CD-767E/O, V1.5X, max PIO2, CDB intr [ 4.888673] ata3.00: configured for PIO0 (device error ignored) [ 4.893984] scsi 2:0:0:0: CD-ROM ACER CD-767E/O 1.5X PQ: 0 ANSI: 5 [ 7.015578] Adding 2541652k swap on /dev/sda2. Priority:-1 extents:1 across:2541652k Signed-off-by:
Ondrej Zary <linux@rainbow-software.org> Signed-off-by:
-
Xiubo Li authored
commit d6b41cb0 upstream. Since we cannot make sure the 'val_count' will always be none zero here, and then if it equals to zero, the kmemdup() will return ZERO_SIZE_PTR, which equals to ((void *)16). So this patch fix this with just doing the zero check before calling kmemdup(). Signed-off-by:
Xiubo Li <Li.Xiubo@freescale.com> Signed-off-by:
Mark Brown <broonie@kernel.org> [lizf: Backported to 3.4: release mutex before returning EINVAL] Signed-off-by:
-
Xiubo Li authored
commit 2c98e0c1 upstream. If 'map->dev' is NULL and there will lead dev_name() to be NULL pointer dereference. So before dev_name(), we need to have check of the map->dev pionter. We also should make sure that the 'name' pointer shouldn't be NULL for debugfs_create_dir(). So here using one default "dummy" debugfs name when the 'name' pointer and 'map->dev' are both NULL. Signed-off-by:
-
Willy Tarreau authored
commit 72cf9012 upstream. This fix ensures that we never meet an integer overflow while adding 255 while parsing a variable length encoding. It works differently from commit 206a81c1 ("lzo: properly check for overruns") because instead of ensuring that we don't overrun the input, which is tricky to guarantee due to many assumptions in the code, it simply checks that the cumulated number of 255 read cannot overflow by bounding this number. The MAX_255_COUNT is the maximum number of times we can add 255 to a base count without overflowing an integer. The multiply will overflow when multiplying 255 by more than MAXINT/255. The sum will overflow earlier depending on the base count. Since the base count is taken from a u8 and a few bits, it is safe to assume that it will always be lower than or equal to 2*255, thus we can always prevent any overflow by accepting two less 255 steps. This patch also reduces the CPU overhead and actually increases performance by 1.1% compared to the initial code, while the previous fix costs 3.1% (measured on x86_64). The fix needs to be backported to all currently supported stable kernels. Reported-by:
Willem Pinckaers <willem@lekkertech.net> Cc: "Don A. Bailey" <donb@securitymouse.com> Signed-off-by:
Willy Tarreau <w@1wt.eu> Signed-off-by:
-
Willy Tarreau authored
commit af958a38 upstream. This reverts commit 206a81c1 ("lzo: properly check for overruns"). As analysed by Willem Pinckaers, this fix is still incomplete on certain rare corner cases, and it is easier to restart from the original code. Reported-by:
-
Willy Tarreau authored
commit d98a0526 upstream. Add a complete description of the LZO format as processed by the decompressor. I have not found a public specification of this format hence this analysis, which will be used to better understand the code. Cc: Willem Pinckaers <willem@lekkertech.net> Cc: "Don A. Bailey" <donb@securitymouse.com> Signed-off-by:
-
Stanislaw Gruszka authored
commit 01f7feea upstream. Two bits control TX power on BBP_R1 register. Correct the mask, otherwise we clear additional bit on BBP_R1 register, what can have unknown, possible negative effect. Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
Krzysztof Kozlowski authored
commit 661a8886 upstream. NULL pointer exception happens during charger-manager probe if 'cm-fuel-gauge' property is not present. [ 2.448536] Unable to handle kernel NULL pointer dereference at virtual address 00000000 [ 2.456572] pgd = c0004000 [ 2.459217] [00000000] *pgd=00000000 [ 2.462759] Internal error: Oops: 5 [#1] PREEMPT SMP ARM [ 2.468047] Modules linked in: [ 2.471089] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.17.0-rc6-00251-ge44cf96cd525-dirty #969 [ 2.479765] task: ea890000 ti: ea87a000 task.ti: ea87a000 [ 2.485161] PC is at strcmp+0x4/0x30 [ 2.488719] LR is at power_supply_match_device_by_name+0x10/0x1c [ 2.494695] pc : [<c01f4220>] lr : [<c030fe38>] psr: a0000113 [ 2.494695] sp : ea87bde0 ip : 00000000 fp : eaa97010 [ 2.506150] r10: 00000004 r9 : ea97269c r8 : ea3bbfd0 [ 2.511360] r7 : eaa97000 r6 : c030fe28 r5 : 00000000 r4 : ea3b0000 [ 2.517869] r3 : 0000006d r2 : 00000000 r1 : 00000000 r0 : c057c195 [ 2.524381] Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel [ 2.531671] Control: 10c5387d Table: 4000404a DAC: 00000015 [ 2.537399] Process swapper/0 (pid: 1, stack limit = 0xea87a240) [ 2.543388] Stack: (0xea87bde0 to 0xea87c000) [ 2.547733] bde0: ea3b0210 c026b1c8 eaa97010 eaa97000 eaa97010 eabb60a8 ea3b0210 00000000 [ 2.555891] be00: 00000008 ea2db210 ea1a3410 c030fee0 ea3bbf90 c03138fc c068969c c013526c [ 2.564050] be20: eaa040c0 00000000 c068969c 00000000 eaa040c0 ea2da300 00000002 00000000 [ 2.572208] be40: 00000001 ea2da3c0 00000000 00000001 00000000 eaa97010 c068969c 00000000 [ 2.580367] be60: 00000000 c068969c 00000000 00000002 00000000 c026b71c c026b6f0 eaa97010 [ 2.588527] be80: c0e82530 c026a330 00000000 eaa97010 c068969c eaa97044 00000000 c061df50 [ 2.596686] bea0: ea87a000 c026a4dc 00000000 c068969c c026a448 c0268b5c ea8054a8 eaa8fd50 [ 2.604845] bec0: c068969c ea2db180 c06801f8 c0269b18 c0590f68 c068969c c0656c98 c068969c [ 2.613004] bee0: c0656c98 ea3bbe40 c06988c0 c026aaf0 00000000 c0656c98 c0656c98 c00088a4 [ 2.621163] bf00: 00000000 c0055f48 00000000 00000004 00000000 ea890000 c05dbc54 c062c178 [ 2.629323] bf20: c0603518 c005f674 00000001 ea87a000 eb7ff83b c0476440 00000091 c003d41c [ 2.637482] bf40: c05db344 00000007 eb7ff858 00000007 c065a76c c0647d24 00000007 c062c170 [ 2.645642] bf60: c06988c0 00000091 c062c178 c0603518 00000000 c0603cc4 00000007 00000007 [ 2.653801] bf80: c0603518 c0c0c0c0 00000000 c0453948 00000000 00000000 00000000 00000000 [ 2.661959] bfa0: 00000000 c0453950 00000000 c000e728 00000000 00000000 00000000 00000000 [ 2.670118] bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 2.678277] bfe0: 00000000 00000000 00000000 00000000 00000013 00000000 c0c0c0c0 c0c0c0c0 [ 2.686454] [<c01f4220>] (strcmp) from [<c030fe38>] (power_supply_match_device_by_name+0x10/0x1c) [ 2.695303] [<c030fe38>] (power_supply_match_device_by_name) from [<c026b1c8>] (class_find_device+0x54/0xac) [ 2.705106] [<c026b1c8>] (class_find_device) from [<c030fee0>] (power_supply_get_by_name+0x1c/0x30) [ 2.714137] [<c030fee0>] (power_supply_get_by_name) from [<c03138fc>] (charger_manager_probe+0x3d8/0xe58) [ 2.723683] [<c03138fc>] (charger_manager_probe) from [<c026b71c>] (platform_drv_probe+0x2c/0x5c) [ 2.732532] [<c026b71c>] (platform_drv_probe) from [<c026a330>] (driver_probe_device+0x10c/0x224) [ 2.741384] [<c026a330>] (driver_probe_device) from [<c026a4dc>] (__driver_attach+0x94/0x98) [ 2.749813] [<c026a4dc>] (__driver_attach) from [<c0268b5c>] (bus_for_each_dev+0x54/0x88) [ 2.757969] [<c0268b5c>] (bus_for_each_dev) from [<c0269b18>] (bus_add_driver+0xd4/0x1d0) [ 2.766123] [<c0269b18>] (bus_add_driver) from [<c026aaf0>] (driver_register+0x78/0xf4) [ 2.774110] [<c026aaf0>] (driver_register) from [<c00088a4>] (do_one_initcall+0x80/0x1bc) [ 2.782276] [<c00088a4>] (do_one_initcall) from [<c0603cc4>] (kernel_init_freeable+0x100/0x1cc) [ 2.790952] [<c0603cc4>] (kernel_init_freeable) from [<c0453950>] (kernel_init+0x8/0xec) [ 2.799029] [<c0453950>] (kernel_init) from [<c000e728>] (ret_from_fork+0x14/0x2c) [ 2.806572] Code: e12fff1e e1a03000 eafffff7 e4d03001 (e4d12001) [ 2.812832] ---[ end trace 7f12556111b9e7ef ]--- Signed-off-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com> Fixes: 856ee611 ("charger-manager: Support deivce tree in charger manager driver") Signed-off-by:
Sebastian Reichel <sre@kernel.org> Signed-off-by:
-
Benjamin Coddington authored
commit 173b3afc upstream. If rpc.statd is restarted, upcalls to monitor hosts can fail with ECONNREFUSED. In that case force a lookup of statd's new port and retry the upcall. Signed-off-by:
Benjamin Coddington <bcodding@redhat.com> Signed-off-by:
-
Bryan O'Donoghue authored
commit ee1b5b16 upstream. Quark x1000 advertises PGE via the standard CPUID method PGE bits exist in Quark X1000's PTEs. In order to flush an individual PTE it is necessary to reload CR3 irrespective of the PTE.PGE bit. See Quark Core_DevMan_001.pdf section 6.4.11 This bug was fixed in Galileo kernels, unfixed vanilla kernels are expected to crash and burn on this platform. Signed-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
David Matlack authored
commit 2ea75be3 upstream. vcpu ioctls can hang the calling thread if issued while a vcpu is running. However, invalid ioctls can happen when userspace tries to probe the kind of file descriptors (e.g. isatty() calls ioctl(TCGETS)); in that case, we know the ioctl is going to be rejected as invalid anyway and we can fail before trying to take the vcpu mutex. This patch does not change functionality, it just makes invalid ioctls fail faster. Signed-off-by:
David Matlack <dmatlack@google.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> [lizf: Backported to 3.4: adjust context] Signed-off-by:
-
Andy Shevchenko authored
commit 8e45ef68 upstream. Do full clean up at exit, means terminate all ongoing DMA transfers. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Andy Shevchenko authored
commit b41583e7 upstream. In case of 8 bit mode and DMA usage we end up with every second byte written as 0. We have to respect bits_per_word settings what this patch actually does. Signed-off-by:
-
K. Y. Srinivasan authored
commit 98d731bb upstream. Eliminate calls to BUG_ON() in vmbus_close_internal(). We have chosen to potentially leak memory, than crash the guest in case of failures. In this version of the patch I have addressed comments from Dan Carpenter (dan.carpenter@oracle.com). Signed-off-by:
K. Y. Srinivasan <kys@microsoft.com> Tested-by:
Sitsofe Wheeler <sitsofe@yahoo.com> Signed-off-by:
-
K. Y. Srinivasan authored
commit 45d727ce upstream. Fix a bug in vmbus_open() and properly propagate the error. I would like to thank Dexuan Cui <decui@microsoft.com> for identifying the issue. Signed-off-by:
-
K. Y. Srinivasan authored
commit 72c6b71c upstream. Eliminate the call to BUG_ON() by waiting for the host to respond. We are trying to reclaim the ownership of memory that was given to the host and so we will have to wait until the host responds. Signed-off-by:
-
K. Y. Srinivasan authored
commit 66be6530 upstream. Eliminate calls to BUG_ON() by properly handling errors. In cases where rollback is possible, we will return the appropriate error to have the calling code decide how to rollback state. In the case where we are transferring ownership of the guest physical pages to the host, we will wait for the host to respond. Signed-off-by:
-
K. Y. Srinivasan authored
commit fdeebcc6 upstream. Posting messages to the host can fail because of transient resource related failures. Correctly deal with these failures and increase the number of attempts to post the message before giving up. In this version of the patch, I have normalized the error code to Linux error code. Signed-off-by:
-
Kees Cook authored
commit 471b095d upstream. An empty firmware request name will trigger warnings when building device names. Make sure this is caught earlier and rejected. The warning was visible via the test_firmware.ko module interface: echo -ne "\x00" > /sys/devices/virtual/misc/test_firmware/trigger_request Reported-by:
Sasha Levin <sasha.levin@oracle.com> Signed-off-by:
Kees Cook <keescook@chromium.org> Tested-by:
-
Lu Baolu authored
commit ddbe1fca upstream. This full-speed USB device generates spurious remote wakeup event as soon as USB_DEVICE_REMOTE_WAKEUP feature is set. As the result, Linux can't enter system suspend and S0ix power saving modes once this keyboard is used. This patch tries to introduce USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk. With this quirk set, wakeup capability will be ignored during device configure. This patch could be back-ported to kernels as old as 2.6.39. Signed-off-by:
Lu Baolu <baolu.lu@linux.intel.com> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Ricardo Ribalda Delgado authored
commit 89ec3dcf upstream. Some implementations of modprobe fail to load the driver for a PCI device automatically because the "interface" part of the modalias from the kernel is lowercase, and the modalias from file2alias is uppercase. The "interface" is the low-order byte of the Class Code, defined in PCI r3.0, Appendix D. Most interface types defined in the spec do not use alpha characters, so they won't be affected. For example, 00h, 01h, 10h, 20h, etc. are unaffected. Print the "interface" byte of the Class Code in uppercase hex, as we already do for the Vendor ID, Device ID, Class, etc. [bhelgaas: changelog] Signed-off-by:
Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Acked-by:
-
Andreas Bomholtz authored
commit dee80ad1 upstream. Added the Seluxit ApS USB Serial Dongle to cp210x driver. Signed-off-by:
Andreas Bomholtz <andreas@seluxit.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Joe Savage authored
commit bfc2d7df upstream. Added support for Ketra N1 wireless interface, which uses the Silicon Labs' CP2104 USB to UART bridge with customized PID 8946. Signed-off-by:
Joe Savage <joe.savage@goketra.com> Signed-off-by:
-
Guenter Roeck authored
commit bb2e226b upstream. This reverts commit 3189eddb ("percpu: free percpu allocation info for uniprocessor system"). The commit causes a hang with a crisv32 image. This may be an architecture problem, but at least for now the revert is necessary to be able to boot a crisv32 image. Cc: Tejun Heo <tj@kernel.org> Cc: Honggang Li <enjoymindful@gmail.com> Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Johan Hedberg authored
commit 5eb596f5 upstream. We can only determine the final security level when both pairing request and response have been exchanged. When initiating pairing the starting target security level is set to MEDIUM unless explicitly specified to be HIGH, so that we can still perform pairing even if the remote doesn't have MITM capabilities. However, once we've received the pairing response we should re-consult the remote and local IO capabilities and upgrade the target security level if necessary. Without this patch the resulting Long Term Key will occasionally be reported to be unauthenticated when it in reality is an authenticated one. Signed-off-by:
Johan Hedberg <johan.hedberg@intel.com> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> [lizf: Backported to 3.4: adjust context] Signed-off-by:
-
Douglas Lehr authored
commit 9fe373f9 upstream. The Crocodile chip occasionally comes up with 4k and 8k BAR sizes. Due to an erratum, setting the SR-IOV page size causes the physical function BARs to expand to the system page size. Since ppc64 uses 64k pages, when Linux tries to assign the smaller resource sizes to the now 64k BARs the address will be truncated and the BARs will overlap. Force Linux to allocate the resource as a full page, which avoids the overlap. [bhelgaas: print expanded resource, too] Signed-off-by:
Douglas Lehr <dllehr@us.ibm.com> Signed-off-by:
Anton Blanchard <anton@samba.org> Signed-off-by:
Milton Miller <miltonm@us.ibm.com> Signed-off-by:
-
Andreas Noever authored
commit bceee4a9 upstream. pciehp assumes that dev->subordinate, the struct pci_bus for a bridge's secondary bus, exists. But we do not create that bus if we run out of bus numbers during enumeration. This leads to a NULL dereference in init_slot() (and other places). Change pciehp_probe() to return -ENODEV when no secondary bus is present. Signed-off-by:
Andreas Noever <andreas.noever@gmail.com> Signed-off-by:
-
Christian Borntraeger authored
commit f346026e upstream. We must not fallthrough if the conditions for external call are not met. Signed-off-by:
Christian Borntraeger <borntraeger@de.ibm.com> Reviewed-by:
Thomas Huth <thuth@linux.vnet.ibm.com> Signed-off-by:
-
Champion Chen authored
commit 85560c4a upstream. Suspend could fail for some platforms because btusb_suspend==> btusb_stop_traffic ==> usb_kill_anchored_urbs. When btusb_bulk_complete returns before system suspend and resubmits an URB, the system cannot enter suspend state. Signed-off-by:
Champion Chen <champion_chen@realsil.com.cn> Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
-
