On a HP 288 Pro G6, the front mic could not be detected.In order to
get it working, the pin configuration needs to be set correctly, and
the ALC671_FIXUP_HP_HEADSET_MIC2 fixup needs to be applied.
Signed-off-by: Meng Tang <tangmeng@uniontech.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220712092222.21738-1-tangmeng@uniontech.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

Another Dell model, another fixup entry: Latitude E5430 needs the same
fixup as other Latitude E series as workaround for noise problems.
Signed-off-by: Meng Tang <tangmeng@uniontech.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220712060005.20176-1-tangmeng@uniontech.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

There is another HP ProDesk 600 G3 model with the PCI SSID 103c:82b4
that requires the quirk HP_MIC_NO_PRESENCE. Add the corresponding
entry to the quirk table.
Signed-off-by: Meng Tang <tangmeng@uniontech.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220711101744.25189-1-tangmeng@uniontech.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

The issue on Acer SWIFT SF313-51 is that headset microphone
doesn't work. The following quirk fixed headset microphone issue.
Note that the fixup of SF314-54/55 (ALC256_FIXUP_ACER_HEADSET_MIC)
was not successful on my SF313-51.
Signed-off-by: Meng Tang <tangmeng@uniontech.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220711081527.6254-1-tangmeng@uniontech.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

Merge tag 'asoc-fix-v5.19-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

ASoC: Fixes for v5.19

Quite a large batch due to things building up for a couple of weeks but
all driver specific apart from Marek's documentation fix.

The struct nhlt_format's fmt_config is a flexible array, it must not be
used as normal array.
When moving to the next nhlt_fmt_cfg we need to take into account the data
behind the ->config.caps (indicated by ->config.size).

The logic of the code also changed: it is no longer saves the _last_
fmt_cfg for all found rates.

Fixes: bc2bd45b ("ASoC: Intel: Skylake: Parse nhlt and register clock device")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220630065638.11183-3-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The present flag is only set once when one rate has been found to be saved.
This will effectively going to ignore any rate discovered at later time and
based on the code, this is not the intention.

Fixes: bc2bd45b ("ASoC: Intel: Skylake: Parse nhlt and register clock device")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220630065638.11183-2-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The patch fixes the wrong state of JD1 and JD2 while the bst1 or bst2 is
power on in the HDA JD using.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Reported-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/20220705101134.16792-1-oder_chiou@realtek.comSigned-off-by: Mark Brown <broonie@kernel.org>

Starting from ADL platform we have four HDMI PCM devices which exceeds
the size of sof_hdmi array. Since each sof_hdmi_pcm structure
represents one HDMI PCM device, we remove the sof_hdmi array and add a
new member hdmi_jack to the sof_hdmi_pcm structure to fix the
out-of-bounds problem.
Signed-off-by: Brent Lu <brent.lu@intel.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20220701141517.264070-1-brent.lu@intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

q6apm_get_audioreach_graph() allocates a memory chunk for graph->graph
with audioreach_alloc_graph_pkt(). When idr_alloc() fails, graph->graph
is not released, which will lead to a memory leak.

We can release the graph->graph with kfree() when idr_alloc() fails to
fix the memory leak.
Signed-off-by: Jianglei Nie <niejianglei2021@163.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220629182520.2164409-1-niejianglei2021@163.comSigned-off-by: Mark Brown <broonie@kernel.org>

The register default is 0x28 per the datasheet, and the amp gain field
is supposed to be shifted left by one. With the wrong default, the ALSA
controls lie about the power-up state. With the wrong shift, we get only
half the gain we expect.
Signed-off-by: Hector Martin <marcan@marcan.st>
Fixes: 827ed8a0 ("ASoC: tas2764: Add the driver for the TAS2764")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220630075135.2221-4-povik+lin@cutebit.orgSigned-off-by: Mark Brown <broonie@kernel.org>

DVC value 0xc8 is -100dB and 0xc9 is mute; this needs to map to
-100.5dB as far as the dB scale is concerned. Fix that and enable
the mute flag, so alsamixer correctly shows the control as
<0 dB .. -100 dB, mute>.
Signed-off-by: Hector Martin <marcan@marcan.st>
Fixes: 827ed8a0 ("ASoC: tas2764: Add the driver for the TAS2764")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220630075135.2221-3-povik+lin@cutebit.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Fix setting of FSYNC polarity in case of LEFT_J and DSP_A/B formats.
Do NOT set the SCFG field as was previously done, because that is not
correct and is also in conflict with the "ASI1 Source" control which
sets the same SCFG field!

Also add support for explicit polarity inversion.

Fixes: 827ed8a0 ("ASoC: tas2764: Add the driver for the TAS2764")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220630075135.2221-2-povik+lin@cutebit.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Make sure there is at least 1 ms delay from reset to first command as
is specified in the datasheet. This is a fix similar to commit
307f3145 ("ASoC: tas2770: Insert post reset delay").

Fixes: 827ed8a0 ("ASoC: tas2764: Add the driver for the TAS2764")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220630075135.2221-1-povik+lin@cutebit.orgSigned-off-by: Mark Brown <broonie@kernel.org>

For the existing msm8916 bindings the minimum reg/reg-names is 1 not 2.
Similarly the minimum interrupt/interrupt-names is 1 not 2.

Fixes: f3fc4fbf ("ASoC: dt-bindings: Add SC7280 lpass cpu bindings")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220629114012.3282945-1-bryan.odonoghue@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Make sure all AC97 interface lines are spelled in capitals,
to avoid confusing readers about where the 5th line is.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Mark Brown <broonie@kernel.org>
Cc: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20220628165840.152235-1-marex@denx.deSigned-off-by: Mark Brown <broonie@kernel.org>

Currently the function arizona_aif_cfg_changed uses the TX_BCLK_RATE,
however this register is not used on wm8998. This was not noticed as
previously snd_soc_component_read did not print an error message.
However, now the log gets filled with error messages, further more the
test for if the LRCLK changed will return spurious results.

Update the code to use the RX_BCLK_RATE register, the LRCLK parameters
are written to both registers and the RX_BCLK_RATE register is used
across all Arizona devices.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220628153409.3266932-4-ckeepax@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

cs47l92_put_demux returns the value of snd_soc_dapm_mux_update_power,
which returns a 1 if a path was found for the kcontrol. This is
obviously different to the expected return a 1 if the control
was updated value. This results in spurious notifications to
user-space. Update the handling to only return a 1 when the value is
changed.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220628153409.3266932-3-ckeepax@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

wm8998_inmux_put returns the value of snd_soc_dapm_mux_update_power,
which returns a 1 if a path was found for the kcontrol. This is
obviously different to the expected return a 1 if the control
was updated value. This results in spurious notifications to
user-space. Update the handling to only return a 1 when the value is
changed.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220628153409.3266932-2-ckeepax@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

The output compensation controls always returns zero regardless of if
the control value was updated. This results in missing notifications
to user-space of the control change. Update the handling to return 1
when the value is changed.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220628153409.3266932-1-ckeepax@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

Currently slim_tx_mixer_get reports all TX mixers as enabled when
at least one is, due to it reading the entire tx_port_value bitmask
without testing the specific bit corresponding to a TX port.
Furthermore, using the same bitmask for all capture DAIs makes
setting one mixer affect them all. To prevent this, and since
the SLIM TX muxes effectively only connect to one of the mixers
at a time, turn tx_port_value into an int array storing the DAI
index each of the ports is connected to.
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Link: https://lore.kernel.org/r/20220622061745.35399-1-y.oudjana@protonmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

The tx_mask check doesn't reflect what the driver and the chip support.

The check currently checks for exactly two slots being enabled. The
tlv320adcx140 supports anything between one and eight channels, so relax
the check accordingly.

The tlv320adcx140 supports arbitrary tx_mask settings, but the driver
currently only supports adjacent slots beginning with the first slot,
so extend the check to check that the first slot is being used and that
there are no holes in the tx_mask.

Leave a comment to make it's the driver that limits the tx_mask
settings, not the chip itself.

While at it remove the set-but-unused struct adcx140p_priv::tdm_delay
field.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20220624105716.2579539-1-s.hauer@pengutronix.deSigned-off-by: Mark Brown <broonie@kernel.org>

max98396_dai_set_fmt() modifes register 2041 and touches bits in the mask
0x3a. Make sure to use the right mask for that operation.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20220624104712.1934484-7-daniel@zonque.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Convert to managed versions of sysfs and clk allocation to simplify
unbinding and error handling in probe.  Managed sysfs node
creation specifically addresses the following error seen the second time
probe is attempted after sdma_pcm_platform_register() previously requsted
probe deferral:

sysfs: cannot create duplicate filename '/devices/platform/68000000.ocp/49022000.mcbsp/max_tx_thres'
Signed-off-by: David Owens <dowens@precisionplanting.com>
Link: https://lore.kernel.org/r/20220620183744.3176557-1-dowens@precisionplanting.comSigned-off-by: Mark Brown <broonie@kernel.org>

The example in audio-graph-card2.c has multiple nodes with the same name
in it. Change the port numbers to get different names.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20220624092601.2445224-1-s.hauer@pengutronix.deSigned-off-by: Mark Brown <broonie@kernel.org>

Put the SGTL5000 in a silent/safe state on shutdown/remove, this is
required since the SGTL5000 produces a constant noise on its output
after it is configured and its clock is removed. Without this change
this is happening every time the module is unbound/removed or from
reboot till the clock is enabled again.

The issue was experienced on both a Toradex Colibri/Apalis iMX6, but can
be easily reproduced everywhere just playing something on the codec and
after that removing/unbinding the driver.

Fixes: 9b34e6cc ("ASoC: Add Freescale SGTL5000 codec support")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20220624101301.441314-1-francesco.dolcini@toradex.comSigned-off-by: Mark Brown <broonie@kernel.org>

The previous cleanup with devres may lead to the incorrect release
orders at the probe error handling due to the devres's nature.  Until
we register the card, snd_card_free() has to be called at first for
releasing the stuff properly when the driver tries to manage and
release the stuff via card->private_free().

This patch fixes it by calling snd_card_free() manually on the error
from the probe callback.

Fixes: 5bff69b3 ("ALSA: cs46xx: Allocate resources with device-managed APIs")
Cc: <stable@vger.kernel.org>
Reported-and-tested-by: Jan Engelhardt <jengelh@inai.de>
Link: https://lore.kernel.org/r/p2p1s96o-746-74p4-s95-61qo1p7782pn@vanv.qr
Link: https://lore.kernel.org/r/20220705152336.350-1-tiwai@suse.deSigned-off-by: Takashi Iwai <tiwai@suse.de>

Merge tag 'asoc-fix-v5.19-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

ASoC: Fixes for v5.19

A collection of fixes for v5.19, quite large but nothing major - a good
chunk of it is more stuff that was identified by mixer-test regarding
event generation.

The patch applies the same quirks used for SC-01 at firmware v1.1.0 to
the ones running v1.0.0, with respect to hard-coded sample rates.

I got two more units and successfully tested the patch series with both
firmwares.

The support is now complete (not accounting ASIO).
Signed-off-by: Egor Vorontsov <sdoregor@sdore.me>
Link: https://lore.kernel.org/r/20220627100041.2861494-2-sdoregor@sdore.meSigned-off-by: Takashi Iwai <tiwai@suse.de>

Fiero SC-01 is a USB sound card with two mono inputs and a single
stereo output. The inputs are composed into a single stereo stream.

The device uses a vendor-provided driver on Windows and does not work
at all without it. The driver mostly provides ASIO functionality, but
also alters the way the sound card is queried for sample rates and
clocks.

ALSA queries those failing with an EPIPE (same as Windows 10 does).
Presumably, the vendor-provided driver does not query it at all, simply
matching by VID:PID. Thus, I consider this a buggy firmware and adhere
to a set of fixed endpoint quirks instead.

The soundcard has an internal clock. Implicit feedback mode is required
for the playback.

I have updated my device to v1.1.0 from a Windows 10 VM using a vendor-
provided binary prior to the development, hoping for it to just begin
working. The device provides no obvious way to downgrade the firmware,
and regardless, there's no binary available for v1.0.0 anyway.

Thus, I will be getting another unit to extend the patch with support
for that. Expected to be a simple copy-paste of the existing one,
though.

There were no previous reports of that device in context of Linux
anywhere. Other issues have been reported though, but that's out of the
scope.
Signed-off-by: Egor Vorontsov <sdoregor@sdore.me>
Link: https://lore.kernel.org/r/20220627100041.2861494-1-sdoregor@sdore.meSigned-off-by: Takashi Iwai <tiwai@suse.de>

Fixes headset detection on Clevo L140PU.
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220624144109.3957-1-tcrawford@system76.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

Treat the claimed 96kHz 1ch in the descriptors as 48kHz 2ch, so that
the audio stream doesn't sound mono. Also fix initial stream
alignment, so that left and right channels are in the correct order.
Signed-off-by: John Veness <john-linux@pelago.org.uk>
Link: https://lore.kernel.org/r/20220624140757.28758-1-john-linux@pelago.org.ukSigned-off-by: Takashi Iwai <tiwai@suse.de>

madera_adsp_rate_put always returns zero regardless of if the control
value was updated. This results in missing notifications to user-space
of the control change. Update the handling to return 1 when the
value is changed.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220623105120.1981154-5-ckeepax@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

madera_out1_demux_put returns the value of
snd_soc_dapm_mux_update_power, which returns a 1 if a path was found for
the kcontrol. This is obviously different to the expected return a 1 if
the control was updated value. This results in spurious notifications to
user-space. Update the handling to only return a 1 when the value is
changed.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220623105120.1981154-4-ckeepax@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

cs47l15_in1_adc_put always returns zero regardless of if the control
value was updated. This results in missing notifications to user-space
of the control change. Update the handling to return 1 when the value is
changed.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220623105120.1981154-3-ckeepax@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

The mixer controls for ASP TX3/4 are set to values that are not included
in their enumeration control. This will cause spurious event
notifications when the controls are first changed, as the register value
changes whilst the actual visible enumeration value does not. Use the
register patch to set them to a known value, zero, which equates to zero
fill, thereby avoiding the spurious notifications.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220623105120.1981154-2-ckeepax@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

DAPM keeps a copy of the current value of mux/demux controls,
however this value is only initialised in the case of autodisable
controls. This leads to false notification events when first
modifying a DAPM kcontrol that has a non-zero default.

Autodisable controls are left as they are, since they already
initialise the value, and there would be more work required to
support autodisable muxes where the first option isn't disabled
and/or that isn't the default.

Technically this issue could affect mixer/switch elements as well,
although not on any of the devices I am currently running. There
is also a little more work to do to address the issue there due to
that side supporting stereo controls, so that has not been tackled
in this patch.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220623105120.1981154-1-ckeepax@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

The initial settings will be written before the codec probe function.
But, the rt711->component doesn't be assigned yet.
If IO error happened during initial settings operations, it will cause the kernel panic.
This patch changed component->dev to slave->dev to fix this issue.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20220621090719.30558-1-shumingf@realtek.comSigned-off-by: Mark Brown <broonie@kernel.org>

Various boolean controls on cs35l41 are missing the required "Switch" in
the name, add these.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220621102041.1713504-3-ckeepax@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

The DRE controls on wm5110 should return a value of 1 if the DRE state
is actually changed, update to fix this.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220621102041.1713504-2-ckeepax@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>