Add depend on WATCHDOG, otherwise modpost fails with
  ERROR: modpost: "watchdog_init_timeout" [drivers/platform/cznic/turris-omnia-mcu.ko] undefined!
  ERROR: modpost: "devm_watchdog_register_device" [drivers/platform/cznic/turris-omnia-mcu.ko] undefined!

Fixes: ab89fb5f ("platform: cznic: turris-omnia-mcu: Add support for MCU watchdog")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202407040711.g19y3cWq-lkp@intel.com/Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20240708114002.4285-3-kabel@kernel.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Add depend on OF, otherwise the compilation fails with
  error: no member named 'of_gpio_n_cells' in 'struct gpio_chip'
  error: no member named 'of_xlate' in 'struct gpio_chip'

Fixes: dfa556e4 ("platform: cznic: turris-omnia-mcu: Add support for MCU connected GPIOs")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202407031646.trNSwajF-lkp@intel.com/Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20240708114002.4285-2-kabel@kernel.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Not all registers in PMU_ALIVE block support atomic set/clear operations.
GS101_SYSIP_DAT0 and GS101_SYSTEM_CONFIGURATION registers are two regs
where attempting atomic access fails.

As documentation on exactly which registers support atomic operations is
not forthcoming. We default to atomic access, unless the register is
explicitly added to the tensor_is_atomic() function. Update the comment
to reflect this as well.
Reviewed-by: Will McVicker <willmcvicker@google.com>
Tested-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240628223506.1237523-4-peter.griffin@linaro.orgSigned-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240702063514.6215-2-krzysztof.kozlowski@linaro.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'memory-controller-drv-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl into soc/drivers

Memory controller drivers for v6.11

Make the Freescale IFC driver selectable because it is used now by two
drivers: Freescale NAND and generic NOR flash.  The patches adjusting
defconfig are waiting on the mailing lists to be picked up.

* tag 'memory-controller-drv-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
  dt-bindings: memory: fsl: replace maintainer
  memory: fsl_ifc: Make FSL_IFC config visible and selectable

Link: https://lore.kernel.org/r/20240702070212.8291-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'sunxi-drivers-for-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into soc/drivers

Allwinner SoC driver changes for 6.11

- DT binding addition of regulator node under SRAM node
- Cleanup of unused list in SRAM driver

* tag 'sunxi-drivers-for-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  dt-bindings: sram: sunxi-sram: Add regulators child
  soc: sunxi: sram: Remove unused list 'claimed_sram'

Link: https://lore.kernel.org/r/ZoQZguQ6taJziJ11@wens.twSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Reset controller updates for v6.11, part 2

This tag adds USB VBUS regulator control for Renesas RZ/G2L SoCs,
which also touches PHY driver and device tree, and pulls in a new
regulator_hardware_enable() helper.

The Tegra BPMP reset driver can be compiled under COMPILE_TEST now.

* tag 'reset-for-v6.11-2' of git://git.pengutronix.de/pza/linux:
  arm64: dts: renesas: rz-smarc: Replace fixed regulator for USB VBUS
  phy: renesas: phy-rcar-gen3-usb2: Control VBUS for RZ/G2L SoCs
  reset: renesas: Add USB VBUS regulator device as child
  dt-bindings: reset: renesas,rzg2l-usbphy-ctrl: Document USB VBUS regulator
  reset: tegra-bpmp: allow building under COMPILE_TEST
  regulator: core: Add helper for allow HW access to enable/disable regulator

Link: https://lore.kernel.org/r/20240703100809.2773890-1-p.zabel@pengutronix.deSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'qcom-drivers-for-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/drivers

Qualcomm driver updates for v6.11

Support for Shared Memory (shm) Bridge is added, which provides a
stricter interface for handling of buffers passed to TrustZone.

The X1Elite platform is added to uefisecapp allow list, to instantiate
the efivars implementation.

A new in-kernel implementation of the pd-mapper (or servreg) service is
introduced, to replace the userspace dependency for USB Type-C and
battery management.

Support for sharing interrupts across multiple bwmon instances is added,
and a refcount imbalance issue is corrected.

The LLCC support for recent platforms is corrected, and SA8775P support
is added.

A new interface is added to SMEM, to expose "feature codes". One example
of the usecase for this is to indicate to the GPU driver which
frequencies are available on the given device.

The interrupt consumer and provider side of SMP2P is updated to provide
more useful names in interrupt stats.

Support for using the mailbox binding and driver for outgoing IPC
interrupt in the SMSM driver is introduced.

socinfo driver learns about SDM670 and IPQ5321, as well as get some
updates to the X1E PMICs.

pmic_glink is bumped to now support managing 3 USB Type-C ports.

* tag 'qcom-drivers-for-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (48 commits)
  soc: qcom: smp2p: Use devname for interrupt descriptions
  soc: qcom: smsm: Add missing mailbox dependency to Kconfig
  soc: qcom: add missing pd-mapper dependencies
  soc: qcom: icc-bwmon: Allow for interrupts to be shared across instances
  dt-bindings: interconnect: qcom,msm8998-bwmon: Add X1E80100 BWMON instances
  dt-bindings: interconnect: qcom,msm8998-bwmon: Remove opp-table from the required list
  firmware: qcom: tzmem: export devm_qcom_tzmem_pool_new()
  soc: qcom: add pd-mapper implementation
  soc: qcom: pdr: extract PDR message marshalling data
  soc: qcom: pdr: fix parsing of domains lists
  soc: qcom: pdr: protect locator_addr with the main mutex
  firmware: qcom: scm: clarify the comment in qcom_scm_pas_init_image()
  firmware: qcom: scm: add support for SHM bridge memory carveout
  firmware: qcom: tzmem: enable SHM Bridge support
  firmware: qcom: scm: add support for SHM bridge operations
  firmware: qcom: qseecom: convert to using the TZ allocator
  firmware: qcom: scm: make qcom_scm_qseecom_app_get_id() use the TZ allocator
  firmware: qcom: scm: make qcom_scm_lmh_dcvsh() use the TZ allocator
  firmware: qcom: scm: make qcom_scm_ice_set_key() use the TZ allocator
  firmware: qcom: scm: make qcom_scm_assign_mem() use the TZ allocator
  ...

Link: https://lore.kernel.org/r/20240705034410.13968-1-andersson@kernel.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Add SCMI ARM REGULATOR configuration for stm32.
Signed-off-by: Pascal Paillet <p.paillet@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240705134554.2833835-1-alexandre.torgue@foss.st.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'ti-driver-soc-for-v6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux into soc/drivers

TI SoC driver updates for v6.11

- Update TISCI protocol URL link  which was dead
- socinfo: Add j721E SR 2.0 detection support
- MAINTAINER list additions: ti,pruss.yaml and ti,j721e-system-controller.yaml
- pm33xx: log statement improvement
- knav_qmss: minor data structure optimization

* tag 'ti-driver-soc-for-v6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux:
  dt-bindings: soc: ti: Move ti,j721e-system-controller.yaml to soc/ti
  MAINTAINERS: Add entry for ti,pruss.yaml to TI KEYSTONE MULTICORE NAVIGATOR DRIVERS
  soc: ti: k3-socinfo: Add J721E SR2.0
  soc: ti: knav_qmss: Constify struct knav_range_ops
  firmware: ti_sci: fix TISCI protocol URL link
  dt-bindings: ti: fix TISCI protocol URL link
  soc: ti: pm33xx: Fix missing newlines in log statements

Link: https://lore.kernel.org/r/20240705151449.s4rngkehjn73favn@streamSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'riscv-firmware-for-v6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/drivers

RISC-V firmware drivers for v6.11

Microchip:
Support for writing "bitstream info" to the flash using the auto-update
driver. At this point the "bitstream info" is a glorified dtbo wrapper,
but there's plans to add more info there in the future. Additionally,
rework some allocations in the driver and use scope-based cleanup on
them.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>

* tag 'riscv-firmware-for-v6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
  firmware: microchip: use scope-based cleanup where possible
  firmware: microchip: move buffer allocation into mpfs_auto_update_set_image_address()
  firmware: microchip: support writing bitstream info to flash

Link: https://lore.kernel.org/r/20240707-lukewarm-film-8a9da40a1c27@spudSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'riscv-cache-for-v6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/drivers

RISC-V cache drivers for v6.11

StarFive:
A new driver for the cache controller on the jh8100, which didn't
implement Zicbom and thus needs an implementation of non-standard cache
management operations.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>

* tag 'riscv-cache-for-v6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
  MAINTAINERS: add microchip soc binding directory to microchip soc driver entry
  MAINTAINERS: add cache binding directory to cache driver entry
  cache: Add StarFive StarLink cache management
  dt-bindings: cache: Add docs for StarFive Starlink cache controller

Link: https://lore.kernel.org/r/20240707-whoever-undesired-c5f6e96ae403@spudSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'tegra-for-6.11-soc' of https://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into soc/drivers

soc/tegra: Changes for v6.11-rc1

This is a simple change that condenses two function calls into one in
two places to save some boilerplate.

* tag 'tegra-for-6.11-soc' of https://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  soc/tegra: pmc: Simplify resource lookup

Link: https://lore.kernel.org/r/20240628210818.3627404-1-thierry.reding@gmail.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Replace the fixed regulator for USB VBUS and use the proper one that
controls regulator based on VBUS detection.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240702180032.207275-5-biju.das.jz@bp.renesas.comSigned-off-by: Philipp Zabel <p.zabel@pengutronix.de>

Use regulator_hardware_enable() for controlling VBUS enable for
RZ/G2L alike SoCs in interrupt context.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20240702180032.207275-4-biju.das.jz@bp.renesas.comSigned-off-by: Philipp Zabel <p.zabel@pengutronix.de>

As per RZ/G2L HW manual, VBUS enable can be controlled by the VBOUT bit
of the VBUS Control Register(VBENCTL) register in the USBPHY Control.

Expose this register as regmap and instantiate the USB VBUS regulator
device, so that consumer can control the vbus using regulator API's
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20240702180032.207275-3-biju.das.jz@bp.renesas.comSigned-off-by: Philipp Zabel <p.zabel@pengutronix.de>

The VBUS enable can be controlled by the VBOUT bit of the VBUS control
register. This register is part of usbphy-ctrl IP.

Document the USB VBUS regulator object.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20240702180032.207275-2-biju.das.jz@bp.renesas.comSigned-off-by: Philipp Zabel <p.zabel@pengutronix.de>

Merge tag 'regulator-hw-enable-helper' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into reset/next

regulator: Add helper to allow enable/disable in interrupt context

Add a helper function that enables exclusive consumers to bypass locking
and do an enable/disable from within interrupt context.

Link: https://lore.kernel.org/r/988df019-00d4-4209-8716-39e82c565bf1@sirena.org.ukSigned-off-by: Philipp Zabel <p.zabel@pengutronix.de>

When using /proc/interrupts to collect statistics on smp2p interrupt
counts, it is hard to distinguish the different instances of smp2p from
each other. For example to debug a processor boot issue, the ready and
handover interrupts are checked for sanity to ensure the firmware
reached a specific initialization stage.

Remove "smp2p" string from the irq request so that the irq will default
to the device name. Add an .irq_print_chip() callback to print the irq
chip name as the device name. These two changes allow for a unique name
to be used in /proc/interrupts as shown below.

/ # cat /proc/interrupts | grep smp2p
 18:  ...      ipcc 196610 Edge      smp2p-adsp
 20:  ...      ipcc 131074 Edge      smp2p-modem
170:  ...  smp2p-modem   1 Edge      q6v5 ready
178:  ...  smp2p-adsp   1 Edge      q6v5 ready
Signed-off-by: Chris Lew <quic_clew@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240627104831.4176799-2-quic_sudeepgo@quicinc.comSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Since the smsm driver got the ability to interact with the mailbox using
the mailbox subsystem and not just syscon, we need to add the dependency
to kconfig as well to avoid compile errors.

Fixes: 75287992 ("soc: qcom: smsm: Support using mailbox interface")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202406180006.Z397C67h-lkp@intel.com/Signed-off-by: Luca Weiss <luca@lucaweiss.eu>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240628-smsm-kconfig-v1-1-117d5af4ba1f@lucaweiss.euSigned-off-by: Bjorn Andersson <andersson@kernel.org>

The pd-mapper driver uses auxiliary bus and Qualcomm PDR message format
data. Add missing dependencies to the driver's Kconfig entry.
Reported-by: Mark Brown <broonie@kernel.org>
Fixes: 1ebcde04 ("soc: qcom: add pd-mapper implementation")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Chris Lew <quic_clew@quicinc.com>
Link: https://lore.kernel.org/r/20240626-qcom-pd-mapper-fix-deps-v1-1-644678dc4663@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Merge tag 'amlogic-drivers-for-v6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux into soc/drivers

Amlogic drivers changes for v6.11:
- Add S905L & A113X SoC IDs
- add missing MODULE_DESCRIPTION() macro for meson_sm driver

* tag 'amlogic-drivers-for-v6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux:
  firmware: meson_sm: add missing MODULE_DESCRIPTION() macro
  soc: amlogic: meson-gx-socinfo: add new A113X SoC id
  soc: amlogic: meson-gx-socinfo: Add S905L ID

Link: https://lore.kernel.org/r/35093904-c4a8-432d-b010-a994fc1ee536@linaro.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Add support for true random number generator provided by the MCU.
New Omnia boards come without the Atmel SHA204-A chip. Instead the
crypto functionality is provided by new microcontroller, which has
a TRNG peripheral.
Signed-off-by: Marek Behún <kabel@kernel.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20240701113010.16447-7-kabel@kernel.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Add support for the watchdog mechanism provided by the MCU.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20240701113010.16447-6-kabel@kernel.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Add support for true board poweroff (MCU can disable all unnecessary
voltage regulators) and wakeup at a specified time, implemented via a
RTC driver so that the rtcwake utility can be used to configure it.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20240701113010.16447-5-kabel@kernel.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Add support for GPIOs connected to the MCU on the Turris Omnia board.

This includes:
- front button pin
- enable pins for USB regulators
- MiniPCIe / mSATA card presence pins in MiniPCIe port 0
- LED output pins from WAN ethernet PHY, LAN switch and MiniPCIe ports
- on board revisions 32+ also various peripheral resets and another
  voltage regulator enable pin
Signed-off-by: Marek Behún <kabel@kernel.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20240701113010.16447-4-kabel@kernel.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Add the basic skeleton for a new platform driver for the microcontroller
found on the Turris Omnia board.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20240701113010.16447-3-kabel@kernel.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Add binding for cznic,turris-omnia-mcu, the device-tree node
representing the system-controller features provided by the MCU on the
Turris Omnia router.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20240701113010.16447-2-kabel@kernel.orgSigned-off-by: Arnd Bergmann <arnd@arndb.de>

soc/ti is the more appropriate location for the system controller
device tree binding documentation so move there.

Update Kishon's email address to a working one.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20240520-for-v6-11-j721e-syscon-v1-1-f57a93e12cad@kernel.orgSigned-off-by: Nishanth Menon <nm@ti.com>

The Tegra BPMP reset driver can be compiled without TEGRA_BPMP being
enabled. Allow it to be built under COMPILE_TEST.
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20240625-reset-compile-bpmp-v1-1-647e846303d8@pengutronix.deSigned-off-by: Philipp Zabel <p.zabel@pengutronix.de>

Some sunxi SoCs have in-package regulators controlled by a register in
the system control MMIO block. Allow a child node for this regulator
device in addition to SRAM child nodes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240622150731.1105901-2-wens@kernel.orgSigned-off-by: Chen-Yu Tsai <wens@csie.org>

Merge tag 'mtk-soc-for-v6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mediatek/linux into soc/drivers

MediaTek driver updates for v6.11

This adds the previously missed Tone Curve Conversion (TCC)
MuteX bit to enable the same in MDP3 on the the MT8188 SoC,
disables 9-bit Alpha for display HDR support in MT8195 and
adds math operation support in the Global Command Engine for
all MediaTek SoCs, which will be used in the near future in
the ISP driver.

* tag 'mtk-soc-for-v6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mediatek/linux:
  soc: mtk-cmdq: Add cmdq_pkt_logic_command to support math operation
  soc: mediatek: Disable 9-bit alpha in ETHDR
  soc: mediatek: mtk-mutex: Add MDP_TCC0 mod to MT8188 mutex table

Link: https://lore.kernel.org/r/20240628093801.126013-3-angelogioacchino.delregno@collabora.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Currently there is no entry for
Documentation/devicetree/bindings/soc/ti/ti,pruss.yaml file. The driver
file corresponding to this binding file is drivers/soc/ti/pruss.c which
is maintained in TI KEYSTONE MULTICORE NAVIGATOR DRIVERS. Add the
binding file also to the same section so that this could be maintained.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://lore.kernel.org/r/20240625153319.795665-2-danishanwar@ti.comSigned-off-by: Nishanth Menon <nm@ti.com>

Add support to detect J721E SR2.0
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Link: https://lore.kernel.org/r/20240624065205.718449-1-n-francis@ti.comSigned-off-by: Nishanth Menon <nm@ti.com>

'struct knav_range_ops' is not modified in these drivers.

Constifying this structure moves some data to a read-only section, so
increase overall security.

On a x86_64, with allmodconfig:
Before:
======
   text	   data	    bss	    dec	    hex	filename
   7498	   1193	      0	   8691	   21f3	drivers/soc/ti/knav_qmss_acc.o

After:
=====
   text	   data	    bss	    dec	    hex	filename
   7566	   1145	      0	   8711	   2207	drivers/soc/ti/knav_qmss_acc.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/a8b4b428f97fc584f38bf45100aa9da241aeb935.1719159074.git.christophe.jaillet@wanadoo.frSigned-off-by: Nishanth Menon <nm@ti.com>

The http://processors.wiki.ti.com EOL in january 2021

Fix the old URL with the new one.
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
Link: https://lore.kernel.org/r/20240618150933.1824185-3-richard.genoud@bootlin.comSigned-off-by: Nishanth Menon <nm@ti.com>

The http://processors.wiki.ti.com EOL in january 2021

Fix the old URL with the new one.
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240618150933.1824185-2-richard.genoud@bootlin.comSigned-off-by: Nishanth Menon <nm@ti.com>

Add the missing newline characters to two pm33xx log statements
to ensure proper log formatting.
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Link: https://lore.kernel.org/r/20240517212930.2019962-1-gomonovych@gmail.comSigned-off-by: Nishanth Menon <nm@ti.com>

I noticed that there's technically not an explicit maintainer for this
directory, even if the files currently in it are covered by either the
Mircochip FPGA or AT91 entries. Add it to the entry covering the
corresponding driver directory.
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>

The directory covering cache controller bindings has no MAINTAINER other
than the fallback to myself, Rob and Krzysztof. Add it to the entry for
the corresponding drivers.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>

Merge tag 'optee-notif-wait-timeout-for-v6.11' of https://git.linaro.org/people/jens.wiklander/linux-tee into soc/drivers

optee: add timeout parameter for notification wait

* tag 'optee-notif-wait-timeout-for-v6.11' of https://git.linaro.org/people/jens.wiklander/linux-tee:
  optee: add timeout value to optee_notif_wait() to support timeout

Link: https://lore.kernel.org/r/20240627095325.GA2585076@raydenSigned-off-by: Arnd Bergmann <arnd@arndb.de>