- 03 Jul, 2017 1 commit
-
-
Shawn Lin authored
Rockchip's RC has two banks of registers for the root port: a normal bank that is strictly compatible with the PCIe spec, and a privileged bank that can be used to change RO bits of root port registers. When probing the RC driver, we use the privileged bank to do some basic setup work as some RO bits are hw-inited to wrong value. But we didn't change to the normal bank after probing the driver. This leads to a serious problem when the PME code tries to clear the PME status by writing PCI_EXP_RTSTA_PME to the register of PCI_EXP_RTSTA. Per PCIe 3.0 spec, section 7.8.14, the PME status bit is RW1C. So the PME code is doing the right thing to clear the PME status but we find the RC doesn't clear it but actually setting it to one. So finally the system trap in pcie_pme_work_fn() as PCI_EXP_RTSTA_PME is true now forever. This issue can be reproduced by booting kernel with pci=nomsi. Use the normal register bank for the PCI config accessors. The privileged bank is used only internally by this driver. Fixes: e77f847d ("PCI: rockchip: Add Rockchip PCIe controller support") Signed-off-by:
Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org Cc: Jeffy Chen <jeffy.chen@rock-chips.com> Cc: Brian Norris <briannorris@chromium.org>
-
- 02 Jul, 2017 39 commits
-
-
Shawn Lin authored
We have a local "struct device *dev" in rockchip_pcie_probe(). Use it consistently throughout the function. No functional change intended. Signed-off-by:
-
Arvind Yadav authored
clk_prepare_enable() can fail here and we must check its return value. Signed-off-by:
Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by:
Heiko Stuebner <heiko@sntech.de> Acked-by:
-
Shawn Lin authored
Wenrui Li changed his employer and is no longer able to maintain the Rockchip PCIe driver, so remove his email address from this file. Signed-off-by:
-
Shawn Lin authored
The default value of MPS for RC is 128 bytes, but actually it could support 256 bytes. So this patch fixes this issue. Signed-off-by:
-
Shawn Lin authored
Per PCIe base specification (Revision 3.1a), section 7.5.3, type 1 configuration space header should be used when accessing PCIe switch. So we need to reconfigure the header according to the bus number we are accessing. Otherwise we could not visit the buses behind the switch. Signed-off-by:
-
Shawn Lin authored
We need to reconfigure the header type later, so split out a new function. Signed-off-by:
-
Shawn Lin authored
Configuration accesses is also part of ATU settings, so let's keep all of them inside rockchip_pcie_cfg_atu(). Signed-off-by:
-
Shawn Lin authored
Rename rockchip_cfg_atu() to keep the name consistent with other functions in pcie-rockchip.c. Signed-off-by:
-
Shawn Lin authored
vpcie0v9 is used for PHY, so we could disable it as we don't need PHY to work then in S3 if folks assign it DT. But we should note that there is a side effect that we could not support beacon wakeup if we disable vpcie0v9 for aggressive power-saving. Signed-off-by:
-
Lorenzo Pieralisi authored
With the introduction of struct pci_host_bridge.map_irq pointer it is possible to assign IRQs for all devices originating from a PCI host bridge at probe time; this is implemented through pci_assign_irq() that relies on the struct pci_host_bridge.map_irq pointer to map IRQ for a given device. The benefits this brings are twofold: - the IRQ for a device is assigned once at probe time - the IRQ assignment works also for hotplugged devices With all DT based PCI host bridges converted to the struct pci_host_bridge.{map/swizzle}_irq hooks mechanism the DT IRQ allocation in ARM64 pcibios_alloc_irq() is now redundant and can be removed. Signed-off-by:Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by:
Will Deacon <will.deacon@arm.com>
-
Lorenzo Pieralisi authored
struct pci_host_bridge gained hooks to map/swizzle IRQs, so that the IRQ mapping can be done automatically by PCI core code through the pci_assign_irq() function instead of resorting to arch-specific implementation callbacks to carry out the same task which force PCI host bridge drivers implementation to implement per-arch kludges to carry out a task that is inherently architecture agnostic. Add map/swizzle IRQs hooks to the xilinx-nwl PCI host driver to move the IRQ allocation into core code and stop relying on arch-specific callbacks. Signed-off-by:
-
Lorenzo Pieralisi authored
struct pci_host_bridge gained hooks to map/swizzle IRQs, so that the IRQ mapping can be done automatically by PCI core code through the pci_assign_irq() function instead of resorting to arch-specific implementation callbacks to carry out the same task which force PCI host bridge drivers implementation to implement per-arch kludges to carry out a task that is inherently architecture agnostic. Add map/swizzle IRQs hooks to the rockchip PCI host driver to move the IRQ allocation into core code and stop relying on arch-specific callbacks. Signed-off-by:
-
Lorenzo Pieralisi authored
struct pci_host_bridge gained hooks to map/swizzle IRQs, so that the IRQ mapping can be done automatically by PCI core code through the pci_assign_irq() function instead of resorting to arch-specific implementation callbacks to carry out the same task which force PCI host bridge drivers implementation to implement per-arch kludges to carry out a task that is inherently architecture agnostic. Add map/swizzle IRQs hooks to the xgene PCI host driver to move the IRQ allocation into core code and stop relying on arch-specific callbacks. Tested-by: Khuong Dinh <kdinh@apm.com> # with e1000e Signed-off-by:
-
Lorenzo Pieralisi authored
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now allocated in the pci_assign_irq() callback automatically, PCI host bridge drivers can stop relying on pci_fixup_irqs() for IRQ allocation. Drop pci_fixup_irqs() usage from PCI altera host bridge driver. Signed-off-by:
-
Lorenzo Pieralisi authored
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now allocated in the pci_assign_irq() callback automatically, PCI host bridge drivers can stop relying on pci_fixup_irqs() for IRQ allocation. Drop pci_fixup_irqs() usage from PCI versatile host bridge driver. Signed-off-by:
-
Lorenzo Pieralisi authored
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now allocated in the pci_assign_irq() callback automatically, PCI host bridge drivers can stop relying on pci_fixup_irqs() for IRQ allocation. Drop pci_fixup_irqs() usage from PCI host-common bridge driver. Signed-off-by:
-
Lorenzo Pieralisi authored
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now allocated in the pci_assign_irq() callback automatically, PCI host bridge drivers can stop relying on pci_fixup_irqs() for IRQ allocation. Drop pci_fixup_irqs() usage from PCI ftpci100 host bridge driver. Signed-off-by:
-
Lorenzo Pieralisi authored
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now allocated in the pci_assign_irq() callback automatically, PCI host bridge drivers can stop relying on pci_fixup_irqs() for IRQ allocation. Drop pci_fixup_irqs() usage from PCI designware host bridge driver. Signed-off-by:
-
Lorenzo Pieralisi authored
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now allocated in the pci_assign_irq() callback automatically, PCI host bridge drivers can stop relying on pci_fixup_irqs() for IRQ allocation. Drop pci_fixup_irqs() usage from PCI iproc host bridge driver. Signed-off-by:
-
Lorenzo Pieralisi authored
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now allocated in the pci_assign_irq() callback automatically, PCI host bridge drivers can stop relying on pci_fixup_irqs() for IRQ allocation. Drop pci_fixup_irqs() usage from PCI rcar host bridge driver. Signed-off-by:
-
Lorenzo Pieralisi authored
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now allocated in the pci_assign_irq() callback automatically, PCI host bridge drivers can stop relying on pci_fixup_irqs() for IRQ allocation. Drop pci_fixup_irqs() usage from PCI xilinx host bridge driver. Signed-off-by:
-
Lorenzo Pieralisi authored
Since, through struct pci_host_bridge.map/swizzle_irq hooks, IRQs are now allocated in the pci_assign_irq() callback automatically, PCI host bridge drivers can stop relying on pci_fixup_irqs() for IRQ allocation Drop pci_fixup_irqs() usage from PCI tegra host bridge driver. Signed-off-by:
-
Lorenzo Pieralisi authored
Legacy PCI host controllers (ie host controllers that set-up the PCI bus through the ARM pci_common_init() API) are currently relying on pci_fixup_irqs() to assign legacy PCI irqs to devices. This is not ideal in that pci_fixup_irqs() assigns IRQs for all PCI devices present in a given system some of which may well be enabled by the time pci_fixup_irqs() is called (ie a system with multiple host controllers). With the introduction of struct pci_host_bridge.(*map_irq) pointer it is possible to assign IRQs for all devices originating from a PCI host bridge at probe time; this is implemented through pci_assign_irq() that relies on the struct pci_host_bridge.map_irq pointer to map IRQ for a given device. The benefits this brings are twofold: - the IRQ for a device is assigned once at probe time - the IRQ assignment works also for hotplugged devices Remove pci_fixup_irqs() call from bios32 code and rely on pci_assign_irq() to carry out the IRQ mapping at device probe time. The map_irq() and swizzle_irq() struct pci_host_bridge callbacks are set-up in the struct pci_host_bridge created in the bios32 pcibios_init_hw() function and mach-* code paths (for PCI mach implementations that require a specific struct hw_pci.(*scan) function callback). Signed-off-by:
-
Matthew Minter authored
The pci_assign_irq() function allows assignment of an IRQ to devices during device enable time rather than only at boot. Therefore call it in the pci_device_probe() function during the enable device code path so this assignment can be performed. This patch will do nothing on arches which do not set the IRQ mapping function pointers and is therefore currently a nop, however as support for these function pointers is added to arch-specific code this will cause IRQ assignment to migrate to device enable time allowing the new code paths to be used. Signed-off-by:
Matthew Minter <matt@masarand.com> [lorenzo.pieralisi@arm.com: moved pci_assign_irq() call site] Signed-off-by:
-
Matthew Minter authored
With the introduction of struct pci_host_bridge.(*map_irq) function pointer add another direct usage of of_irq_parse_and_map_pci(). Update the function comment to reflect this behaviour. Signed-off-by:
-
Matthew Minter authored
Here we delete the static pdev_fixup_irq() function which is currently what pci_fixup_irqs() uses to actually assign the IRQs and replace it with the pci_assign_irq() function which changes the interface and uses the new function pointers stored in the host bridge structure. Eventually this will allow pci_fixup_irqs() to be removed entirely and the new deferred assignment code path will call pci_assign_irq() directly. However to ensure current users continue to work, a new implementation of pci_fixup_irqs() is introduced which simply wraps the functionality of pci_assign_irq(). Signed-off-by:
-
Matthew Minter authored
In order to defer IRQ assignment arches must be able to register functions to map and swizzle interrupts. These registered functions are stored in the pci_host_bridge struct. Signed-off-by:
-
Matthew Minter authored
The functions included in setup-irq.o currently apply only to a selection of architectures which share common IRQ assignment code. However this code needs to be generalised for all arches to allow deferred IRQ assignment. So the first step is to build it on all architectures. Signed-off-by:
-
Lorenzo Pieralisi authored
The pci_scan_root_bus_bridge() function allows passing a parameterized struct pci_host_bridge and scanning the resulting PCI bus; since the struct msi_controller is part of the struct pci_host_bridge and the struct pci_host_bridge can now be passed to pci_scan_root_bus_bridge() explicitly, there is no need for a scan interface with a MSI controller parameter. With all PCI host controller drivers and platform code relying on pci_scan_root_bus_msi() converted over to pci_scan_root_bus_bridge() the pci_scan_root_bus_msi() becomes obsolete and can be removed. Signed-off-by:
-
Lorenzo Pieralisi authored
The introduction of pci_scan_root_bus_bridge() provides a PCI core API to scan a PCI root bus backed by an already initialized struct pci_host_bridge object, which simplifies the bus scan interface and makes the PCI scan root bus interface easier to generalize as members are added to the struct pci_host_bridge. Convert PCI xilinx-nwl host code to pci_scan_root_bus_bridge() to improve the PCI root bus scanning interface. Signed-off-by:
-
Lorenzo Pieralisi authored
The introduction of pci_scan_root_bus_bridge() provides a PCI core API to scan a PCI root bus backed by an already initialized struct pci_host_bridge object, which simplifies the bus scan interface and makes the PCI scan root bus interface easier to generalize as members are added to the struct pci_host_bridge. Convert PCI rockchip host code to pci_scan_root_bus_bridge() to improve the PCI root bus scanning interface. Signed-off-by:
-
Lorenzo Pieralisi authored
The introduction of pci_scan_root_bus_bridge() provides a PCI core API to scan a PCI root bus backed by an already initialized struct pci_host_bridge object, which simplifies the bus scan interface and makes the PCI scan root bus interface easier to generalize as members are added to the struct pci_host_bridge. Convert PCI host-common code to pci_scan_root_bus_bridge() to improve the PCI root bus scanning interface. Signed-off-by:
-
Lorenzo Pieralisi authored
The introduction of pci_scan_root_bus_bridge() provides a PCI core API to scan a PCI root bus backed by an already initialized struct pci_host_bridge object, which simplifies the bus scan interface and makes the PCI scan root bus interface easier to generalize as members are added to the struct pci_host_bridge. Convert PCI xgene host code to pci_scan_root_bus_bridge() to improve the PCI root bus scanning interface. Tested-by: Khuong Dinh <kdinh@apm.com> # with e1000e Signed-off-by:
-
Lorenzo Pieralisi authored
The introduction of pci_scan_root_bus_bridge() provides a PCI core API to scan a PCI root bus backed by an already initialized struct pci_host_bridge object, which simplifies the bus scan interface and makes the PCI scan root bus interface easier to generalize as members are added to the struct pci_host_bridge. Convert PCI xilinx host code to pci_scan_root_bus_bridge() to improve the PCI root bus scanning interface. Signed-off-by:
-
Lorenzo Pieralisi authored
The introduction of pci_scan_root_bus_bridge() provides a PCI core API to scan a PCI root bus backed by an already initialized struct pci_host_bridge object, which simplifies the bus scan interface and makes the PCI scan root bus interface easier to generalize as members are added to the struct pci_host_bridge. Convert PCI altera host code to pci_scan_root_bus_bridge() to improve the PCI root bus scanning interface. Signed-off-by:
-
Lorenzo Pieralisi authored
The introduction of pci_scan_root_bus_bridge() provides a PCI core API to scan a PCI root bus backed by an already initialized struct pci_host_bridge object, which simplifies the bus scan interface and makes the PCI scan root bus interface easier to generalize as members are added to the struct pci_host_bridge. Convert PCI versatile host code to pci_scan_root_bus_bridge() to improve the PCI root bus scanning interface. Signed-off-by:
-
Lorenzo Pieralisi authored
The introduction of pci_scan_root_bus_bridge() provides a PCI core API to scan a PCI root bus backed by an already initialized struct pci_host_bridge object, which simplifies the bus scan interface and makes the PCI scan root bus interface easier to generalize as members are added to the struct pci_host_bridge. Convert PCI iproc host code to pci_scan_root_bus_bridge() to improve the PCI root bus scanning interface. Signed-off-by:
-
Lorenzo Pieralisi authored
The introduction of pci_scan_root_bus_bridge() provides a PCI core API to scan a PCI root bus backed by an already initialized struct pci_host_bridge object, which simplifies the bus scan interface and makes the PCI scan root bus interface easier to generalize as members are added to the struct pci_host_bridge. Convert PCI rcar host code to pci_scan_root_bus_bridge() to improve the PCI root bus scanning interface. Signed-off-by:
-
Lorenzo Pieralisi authored
The introduction of pci_scan_root_bus_bridge() provides a PCI core API to scan a PCI root bus backed by an already initialized struct pci_host_bridge object, which simplifies the bus scan interface and makes the PCI scan root bus interface easier to generalize as members are added to the struct pci_host_bridge. Convert PCI aardvark host code to pci_scan_root_bus_bridge() to improve the PCI root bus scanning interface. Signed-off-by:
-
