Beniamino Galvani says:

====================
net: arc_emac: fix tx issues

the patches below solve some issues found in the tx ring reclaim
strategy currently implemented in the arc_emac driver.

Without these patches a simple outgoing UDP flow blocks almost
immediately with the socket send buffer full, until some new rx
packets trigger a clean of the tx ring.

Everything seems to work fine on a Radxa Rock with this fix applied.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch changes the logic in tx path to ensure that tx descriptors
are reused for transmission only after they have been reclaimed by
arc_emac_tx_clean().
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the current implementation the cleaning of tx ring is done by the
NAPI poll handler, which is scheduled after rx interrupts. Thus, in
absence of received packets the reclaim of used tx buffers is never
executed, blocking further transmission.

This can be easily reproduced starting the transmission of a UDP flow
with iperf, which blocks almost immediately because skbs are not
returned to the stack and the socket send buffer becomes full.

The patch enables tx interrupts so that the tx reclaim is scheduled
after completed transmissions.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MIPS supports BPF JIT since v3.16-rc1

Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: linux-doc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We wrongly tested QP context bits without BE conversion
as was spotted by sparse...

drivers/infiniband/hw/mlx4/qp.c:1685:38: sparse: restricted __be32 degrades to integer

Fix that!

Fixes: d2fce8a9 ('mlx4: Set user-space raw Ethernet QPs to properly handle VXLAN traffic')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
mlx4 SRIOV fixes

This series contains few SRIOV related fixes from Matan, please apply to net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Changing the vlan stripping policy of the QP isn't supported by older
firmware versions for the INIT2RTR command. Nevertheless, we've used it.

Fix that by doing this policy change using INIT2RTR only if the firmware
supports it, otherwise, we call UPDATE_QP command to do the task.

Fixes: 7677fc9 ('net/mlx4: Strengthen VLAN tags/priorities enforcement in VST mode')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current wrapper implementation of the UPDATE_QP command tries to get
the MAC index, even if MAC wasn't set by the VF. Fix it up to only handle
the MAC field if it's valid.

Fixes: ce8d9e0d ('net/mlx4_core: Add UPDATE_QP SRIOV wrapper support')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When doing VGT->VST->VGT state changes, we used an incorrect mask
for the vlan-stripping-disable (VSD) flag, hence the vlan related policy
for user-space Raw Ethernet QPs open by VFs wasn't really applied.

Fix that, by using the correct mask.

Fixes: f0f829bf ('net/mlx4_core: Add immediate activate for VGT->VST->VGT')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Single port VFs are seen PCI wise on both ports of the PF (we don't have
single port PFs with ConnectX). With this in mind, it's possible for
virtualization tools to try and configure a single ported VF through
the "wrong" PF port.

To handle that, we use the PF driver mapping of single port VFs to NIC
ports and adjust the port value before calling into the low level
code that does the actual VF configuration

Fixes: 449fc488 ('net/mlx4: Adapt code for N-Port VF')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In Dual EMAC, when both interface are up and while doing ifdown with heavy
traffic then skbs already processed by DMA from that slave emac has to be
requeued as still the other interface is up and running.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix a missing __user annotation in a cast of a user space pointer (found by
checker).
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds missing space between "interface" and "by"
in bonding module parameter description.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Linux manpage for recvmsg and sendmsg calls does not explicitly mention setting msg_namelen to 0 when
msg_name passed set as NULL. When developers don't set msg_namelen member in msghdr, it might contain garbage
value which will fail the validation check and sendmsg and recvmsg calls from kernel will return EINVAL. This will
break old binaries and any code for which there is no access to source code.
To fix this, we set msg_namelen to 0 when msg_name is passed as NULL from userland.
Signed-off-by: Ani Sinha <ani@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: systemport and bcmgenet OOM fixes

These two patches fix similar Out of Memory code paths in the SYSTEMPORT and
GENET drivers. Under high memory pressure, we could produce an OOPS by
passing a NULL pointer to dma_unmap_single().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a potential case where we might be failing to refill a
control block, leaving it with both a NULL skb pointer *and* a NULL
dma_unmap_addr.

The way we process incoming packets, by first calling
dma_unmap_single(), and then only checking for a potential NULL skb can
lead to situations where do pass a NULL dma_unmap_addr() to
dma_unmap_single(), resulting in an oops.

Fix this my moving the NULL skb check earlier, since no backing skb
also means no corresponding DMA mapping for this packet.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a potential case where we might be failing to refill a
control block, leaving it with both a NULL skb pointer *and* a NULL
dma_unmap_addr.

The way we process incoming packets, by first calling
dma_unmap_single(), and then only checking for a potential NULL skb can
lead to situations where do pass a NULL dma_unmap_addr() to
dma_unmap_single(), resulting in an oops.

Fix this my moving the NULL skb check earlier, since no backing skb
also means no corresponding DMA mapping for this packet.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver does not support pause autonegotiation so it should return
-EINVAL when the function is called with non-zero autoneg.

Cc: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the following compiler warning:

drivers/net/ethernet/octeon/octeon_mgmt.c: In function 'octeon_mgmt_clean_tx_buffers':
drivers/net/ethernet/octeon/octeon_mgmt.c:295:4: warning: ISO C90 forbids mixed declarations and code [-Wdeclaration-after-statement]
    u64 ns = cvmx_read_csr(CVMX_MIXX_TSTAMP(p->port));
    ^
Signed-off-by: Aaro Koskinen <aaro.koskinen@nsn.com>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit d9b2938a ("net: attempt a single high order allocation)
I forgot to update kerneldoc, as @prio parameter was renamed to @gfp
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The sunvnet driver does not have an rmb() in the ring consumer corresponding
to the wmb() in the producer. According to Documentation/memory-barriers.txt:

"When dealing with CPU-CPU interactions, certain types of memory barrier should
always be paired.  A lack of appropriate pairing is almost certainly an error."

In cases where an rmb() is not a no-op and a consumer is removing data from
the ring while a producer is adding new entries, a load reorder would allow

CPU1						CPU2
----						----
						LOAD desc.size [e.g]
STORE desc.size
<wmb>
set desc.hdr.state = VIO_DESC_READY
						LOAD desc.hdr.state
						[because VIO_DESC_READY, use
						 old desc.size, already loaded
						 out of order]

[CPU2 has reordered apparently unrelated LOADs]

To ensure other desc fields are not loaded before checking VIO_DESC_READY, we
need an rmb() between the check and desc data accesses.

I've also moved the viodbg() call to after the rmb() so that it, too, has
current descriptor data even with reordering, which has the side effect that
it won't print anything for descriptors that are not VIO_DESC_READY as before.
That's a) probably a good thing, since the fields are not necessarily set and,
b) better than adding another rmb() just for viodbg().

This would not be possible if strict-ordering is enforced, but then the
memory barriers should be no-ops in that case.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull s390 fixes from Martin Schwidefsky:
 "A bug fix for the vdso code, the loadparm for booting from SCSI is
  added and the access permissions for the dasd module parameters are
  corrected"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/vdso: remove NULL pointer check from clock_gettime
  s390/ipl: Add missing SCSI loadparm attributes to /sys/firmware
  s390/dasd: Make module parameter visible in sysfs

Pull cgroup fixes from Tejun Heo:
 "This pull request includes Alban's patch to disallow '\n' in cgroup
  names.

  Two other patches from Li to fix a possible oops when cgroup
  destruction races against other file operations and one from Vivek to
  fix a unified hierarchy devel behavior"

* 'for-3.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: check cgroup liveliness before unbreaking kernfs
  cgroup: delay the clearing of cgrp->kn->priv
  cgroup: Display legacy cgroup files on default hierarchy
  cgroup: reject cgroup names with '\n'

Pull percpu fixes from Tejun Heo:
 "One patch to fix a failure path in the alloc path.  The bug is
  dangerous but probably not too likely to actually trigger in the wild
  given that there hasn't been any report yet.

  The other two are low impact fixes"

* 'for-3.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
  percpu: free percpu allocation info for uniprocessor system
  percpu: perform tlb flush after pcpu_map_pages() failure
  percpu: fix pcpu_alloc_pages() failure path

Pull libata fixes from Tejun Heo:
 "Two patches are to add PCI IDs for ICH9 and all others are device
  specific fixes.  Nothing too interesting"

* 'for-3.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  ahci_xgene: Fix the link down in first attempt for the APM X-Gene SoC AHCI SATA host controller driver.
  ahci_xgene: Skip the PHY and clock initialization if already configured by the firmware.
  ahci: add pcid for Marvel 0x9182 controller
  ata: Disabling the async PM for JMicron chip 363/361
  ata_piix: Add Device IDs for Intel 9 Series PCH
  ahci: Add Device IDs for Intel 9 Series PCH
  ata: ahci_tegra: Read calibration fuse

Pull networking fixes from David Miller:

 1) Fix skb leak in mac802154, from Martin Townsend

 2) Use select not depends on NF_NAT for NFT_NAT, from Pablo Neira
    Ayuso

 3) Fix union initializer bogosity in vxlan, from Gerhard Stenzel

 4) Fix RX checksum configuration in stmmac driver, from Giuseppe
    CAVALLARO

 5) Fix TSO with non-accelerated VLANs in e1000, e1000e, bna, ehea,
    i40e, i40evf, mvneta, and qlge, from Vlad Yasevich

 6) Fix capability checks in phy_init_eee(), from Giuseppe CAVALLARO

 7) Try high order allocations more sanely for SKBs, specifically if a
    high order allocation fails, fall back directly to zero order pages
    rather than iterating down one order at a time.  From Eric Dumazet

 8) Fix a memory leak in openvswitch, from Li RongQing

 9) amd-xgbe initializes wrong spinlock, from Thomas Lendacky

10) RTNL locking was busted in setsockopt for anycast and multicast, fix
    from Sabrina Dubroca

11) Fix peer address refcount leak in ipv6, from Nicolas Dichtel

12) DocBook typo fixes, from Masanari Iida

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (101 commits)
  ipv6: restore the behavior of ipv6_sock_ac_drop()
  amd-xgbe: Enable interrupts for all management counters
  amd-xgbe: Treat certain counter registers as 64 bit
  greth: moved TX ring cleaning to NAPI rx poll func
  cnic : Cleanup CONFIG_IPV6 & VLAN check
  net: treewide: Fix typo found in DocBook/networking.xml
  bnx2x: Fix link problems for 1G SFP RJ45 module
  3c59x: avoid panic in boomerang_start_xmit when finding page address:
  netfilter: add explicit Kconfig for NETFILTER_XT_NAT
  ipv6: use addrconf_get_prefix_route() to remove peer addr
  ipv6: fix a refcnt leak with peer addr
  net-timestamp: only report sw timestamp if reporting bit is set
  drivers/net/fddi/skfp/h/skfbi.h: Remove useless PCI_BASE_2ND macros
  l2tp: fix race while getting PMTU on PPP pseudo-wire
  ipv6: fix rtnl locking in setsockopt for anycast and multicast
  VMXNET3: Check for map error in vmxnet3_set_mc
  openvswitch: distinguish between the dropped and consumed skb
  amd-xgbe: Fix initialization of the wrong spin lock
  openvswitch: fix a memory leak
  netfilter: fix missing dependencies in NETFILTER_XT_TARGET_LOG
  ...

John W. Linville says:

====================
pull request: wireless 2014-09-05

Please pull this batch of fixes intended for the 3.17 stream...

For the mac80211 bits, Johannes says:

"Here are a few fixes for mac80211. One has been discussed for a while
and adds a terminating NUL-byte to the alpha2 sent to userspace, which
shouldn't be necessary but since many places treat it as a string we
couldn't move to just sending two bytes.

In addition to that, we have two VLAN fixes from Felix, a mesh fix, a
fix for the recently introduced RX aggregation offload, a revert for
a broken patch (that luckily didn't really cause any harm) and a small
fix for alignment in debugfs."

For the iwlwifi bits, Emmanuel says:

"I revert a patch that disabled CTS to self in dvm because users
reported issues. The revert is CCed to stable since the offending
patch was sent to stable too. I also bump the firmware API versions
since a new firmware is coming up. On top of that, Marcel fixes a
bug I introduced while fixing a bug in our Kconfig file."

Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

It is possible that the interface is already gone after joining
the list of anycast on this interface as we don't hold a refcount
for the device, in this case we are safe to ignore the error.

What's more important, for API compatibility we should not
change this behavior for applications even if it were correct.

Fixes: commit a9ed4a29 ("ipv6: fix rtnl locking in setsockopt for anycast and multicast")
Cc: Sabrina Dubroca <sd@queasysnail.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

new link for - How to piss off a Linux kernel subsystem maintainer
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The NFS/RDMA Kconfig symbol was split into separate options for client
and server in commit 2e8c12e1 ("xprtrdma: add separate Kconfig
options for NFSoRDMA client and server support").

Update the documentation to reflect this split.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "J. Bruce Fields" <bfields@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

hpfall.c was renamed to freefall.c in 3.16, but this file still refer to
hpfall.c instead of freefall.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The example code provided with the i2c device interface documentation
won't compile since it uses the reserved word "register" to name a
variable.

The compiler fails with this error message:

 error: expected identifier or '(' before '=' token
   __u8 register = 0x20; /* Device register to access */
                 ^

Rename the variable "register" to simply "reg" in the example code.

Another couple of typos has been fixed as well.
[Change "! =" to "!=".]
Signed-off-by: Jose Alarcon Roldan <jose.alarcon.roldan@gmail.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Despite the fact that these functions have been around for years, they
are little used (only 15 uses in 13 files at the preseht time) even
though many other files use work-arounds to achieve the same result.

By documenting them, hopefully they will become more widely used.
Signed-off-by: Rob Jones <rob.jones@codethink.co.uk>
Acked-by: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ACPI and power management fixes from Rafael Wysocki:
 "These are regression fixes (ACPI sysfs, ACPI video, suspend test),
  ACPI cpuidle deadlock fix, missing runtime validation of ACPI _DSD
  output, a fix and a new CPU ID for the RAPL driver, new blacklist
  entry for the ACPI EC driver and a couple of trivial cleanups
  (intel_pstate and generic PM domains).

  Specifics:

   - Fix for recently broken test_suspend= command line argument (Rafael
     Wysocki).

   - Fixes for regressions related to the ACPI video driver caused by
     switching the default to native backlight handling in 3.16 from
     Hans de Goede.

   - Fix for a sysfs attribute of ACPI device objects that returns stale
     values sometimes due to the fact that they are cached instead of
     executing the appropriate method (_SUN) every time (broken in
     3.14).  From Yasuaki Ishimatsu.

   - Fix for a deadlock between cpuidle_lock and cpu_hotplug.lock in the
     ACPI processor driver from Jiri Kosina.

   - Runtime output validation for the ACPI _DSD device configuration
     object missing from the support for it that has been introduced
     recently.  From Mika Westerberg.

   - Fix for an unuseful and misleading RAPL (Running Average Power
     Limit) domain detection message in the RAPL driver from Jacob Pan.

   - New Intel Haswell CPU ID for the RAPL driver from Jason Baron.

   - New Clevo W350etq blacklist entry for the ACPI EC driver from Lan
     Tianyu.

   - Cleanup for the intel_pstate driver and the core generic PM domains
     code from Gabriele Mazzotta and Geert Uytterhoeven"

* tag 'pm+acpi-3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / cpuidle: fix deadlock between cpuidle_lock and cpu_hotplug.lock
  ACPI / scan: not cache _SUN value in struct acpi_device_pnp
  cpufreq: intel_pstate: Remove unneeded variable
  powercap / RAPL: change domain detection message
  powercap / RAPL: add support for CPU model 0x3f
  PM / domains: Make generic_pm_domain.name const
  PM / sleep: Fix test_suspend= command line option
  ACPI / EC: Add msi quirk for Clevo W350etq
  ACPI / video: Disable native_backlight on HP ENVY 15 Notebook PC
  ACPI / video: Add a disable_native_backlight quirk
  ACPI / video: Fix use_native_backlight selection logic
  ACPICA: ACPI 5.1: Add support for runtime validation of _DSD package.

Pull filesystem fixes from Al Viro:
 "Several bugfixes (all of them -stable fodder).

  Alexey's one deals with double mutex_lock() in UFS (apparently, nobody
  has tried to test "ufs: sb mutex merge + mutex_destroy" on something
  like file creation/removal on ufs).  Mine deal with two kinds of
  umount bugs, in umount propagation and in handling of automounted
  submounts, both resulting in bogus transient EBUSY from umount"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  ufs: fix deadlocks introduced by sb mutex merge
  fix EBUSY on umount() from MNT_SHRINKABLE
  get rid of propagate_umount() mistakenly treating slaves as busy.

Pull RCU fix from Ingo Molnar:
 "A boot hang fix for the offloaded callback RCU model (RCU_NOCB_CPU=y
  && (TREE_CPU=y || TREE_PREEMPT_RC)) in certain bootup scenarios"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  rcu: Make nocb leader kthreads process pending callbacks after spawning

Pull timer fixes from Thomas Gleixner:
 "Three fixlets from the timer departement:

   - Update the timekeeper before updating vsyscall and pvclock.  This
     fixes the kvm-clock regression reported by Chris and Paolo.

   - Use the proper irq work interface from NMI.  This fixes the
     regression reported by Catalin and Dave.

   - Clarify the compat_nanosleep error handling mechanism to avoid
     future confusion"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timekeeping: Update timekeeper before updating vsyscall and pvclock
  compat: nanosleep: Clarify error handling
  nohz: Restore NMI safe local irq work for local nohz kick

Commit 0244756e ("ufs: sb mutex merge + mutex_destroy") introduces
deadlocks in ufs_new_inode() and ufs_free_inode().
Most callers of that functions acqure the mutex by themselves and
ufs_{new,free}_inode() do that via lock_ufs(),
i.e we have an unavoidable double lock.

The patch proposes to resolve the issue by making sure that
ufs_{new,free}_inode() are not called with the mutex held.

Found by Linux Driver Verification project (linuxtesting.org).

Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull kvm fixes from Paolo Bonzini:
 "A smattering of bug fixes across most architectures"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  powerpc/kvm/cma: Fix panic introduces by signed shift operation
  KVM: s390/mm: Fix guest storage key corruption in ptep_set_access_flags
  KVM: s390/mm: Fix storage key corruption during swapping
  arm/arm64: KVM: Complete WFI/WFE instructions
  ARM/ARM64: KVM: Nuke Hyp-mode tlbs before enabling MMU
  KVM: s390/mm: try a cow on read only pages for key ops
  KVM: s390: Fix user triggerable bug in dead code