- 23 Jul, 2019 38 commits
-
-
Kuninori Morimoto authored
Current ALSA SoC is directly using dai->driver->xxx, thus, it has deep nested bracket, and it makes code unreadable. This patch adds new snd_soc_dai_remvoe() and use it. Signed-off-by:
Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Link: https://lore.kernel.org/r/87imruhn1x.wl-kuninori.morimoto.gx@renesas.comSigned-off-by:
Mark Brown <broonie@kernel.org>
-
Kuninori Morimoto authored
Current ALSA SoC is directly using dai->driver->xxx, thus, it has deep nested bracket, and it makes code unreadable. This patch adds new snd_soc_dai_probe() and use it. Signed-off-by:
-
Kuninori Morimoto authored
Current ALSA SoC is directly using dai->driver->xxx, thus, it has deep nested bracket, and it makes code unreadable. This patch adds new snd_soc_dai_resume() and use it. Signed-off-by:
-
Kuninori Morimoto authored
Current ALSA SoC is directly using dai->driver->xxx, thus, it has deep nested bracket, and it makes code unreadable. This patch adds new snd_soc_dai_suspend() and use it. Signed-off-by:
-
Kuninori Morimoto authored
Current ALSA SoC is directly using dai->driver->ops->xxx, thus, it has deep nested bracket, and it makes code unreadable. This patch adds new snd_soc_dai_delay() and use it. Signed-off-by:
-
Kuninori Morimoto authored
Current ALSA SoC is directly using dai->driver->ops->xxx, thus, it has deep nested bracket, and it makes code unreadable. This patch adds new snd_soc_dai_bespoke_trigger() and use it. Signed-off-by:
-
Kuninori Morimoto authored
Current ALSA SoC is directly using dai->driver->ops->xxx, thus, it has deep nested bracket, and it makes code unreadable. This patch adds new snd_soc_dai_trigger() and use it. Signed-off-by:
-
Kuninori Morimoto authored
Current ALSA SoC is directly using dai->driver->ops->xxx, thus, it has deep nested bracket, and it makes code unreadable. This patch adds new snd_soc_dai_prepare() and use it. Signed-off-by:
-
Kuninori Morimoto authored
Current ALSA SoC is directly using dai->driver->ops->xxx, thus, it has deep nested bracket, and it makes code unreadable. This patch adds new snd_soc_dai_shutdown() and use it. Signed-off-by:
-
Kuninori Morimoto authored
Current ALSA SoC is directly using dai->driver->ops->xxx, thus, it has deep nested bracket, and it makes code unreadable. This patch adds new snd_soc_dai_startup() and use it. Signed-off-by:
-
Kuninori Morimoto authored
Current ALSA SoC is directly using dai->driver->ops->xxx, thus, it has deep nested bracket, and it makes code unreadable. This patch adds new snd_soc_dai_hw_free() and use it. Signed-off-by:
-
Kuninori Morimoto authored
Sometimes ALSA SoC naming is very random. Current soc_dai_hw_params() should use snd_soc_dai_xxx() style. And then, 1st parameter should be dai. Otherwise it is confusable. - soc_dai_hw_params(..., dai); + snd_soc_dai_hw_params(dai, ...); Signed-off-by:
-
Kuninori Morimoto authored
Current ALSA SoC has many snd_soc_dai_xxx() function which is using dai->driver->ops->xxx. But, some of them are implemented as snd_soc_dai_xxx(), but others are directly using dai->driver->ops->xxx. Because of it, the code is not easy to read. This patch creats new soc-dai.c and moves snd_soc_dai_xxx() functions into it. One exception is snd_soc_dai_is_dummy() which is based on soc-utils local variable. We need to keep it as-is there. Others which is directly using dai->driver->ops->xxx will be implemented at soc-dai.c by incremental patches. Signed-off-by:
-
Timo Wischer authored
This patch provides the needed infrastructure to support calling hw_free() at the DAI level. This is for example required to free resources allocated in hw_params() callback. The modification of __rsnd_mod_add_hw_params does not have any side effects because rsnd_mod_ops::hw_params callback is not used by anyone until now. Signed-off-by:
Timo Wischer <twischer@de.adit-jv.com> Signed-off-by:
Jiada Wang <jiada_wang@mentor.com> Link: https://lore.kernel.org/r/20190722072403.11008-2-jiada_wang@mentor.comSigned-off-by:
-
Shuming Fan authored
Convert include and source files to SPDX. Signed-off-by:
Shuming Fan <shumingf@realtek.com> Link: https://lore.kernel.org/r/20190723101247.19741-1-shumingf@realtek.comSigned-off-by:
-
Christophe JAILLET authored
All function names start with rt5665_, except 'rt5655_set_verf()'. It is likely a typo. Fix it to be consistent. Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/20190722212639.26954-1-christophe.jaillet@wanadoo.frSigned-off-by:
-
Rander Wang authored
snd_hdac_ext_link_clear_stream_id maps stream id to link output, which is for playback, not capture. Tested on Whiskey Lake platform. Signed-off-by:
Rander Wang <rander.wang@linux.intel.com> Signed-off-by:
Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20190722141402.7194-20-pierre-louis.bossart@linux.intel.comSigned-off-by:
-
Rander Wang authored
For this bug, there are two capture pcm streams active, with one stream and its related stream tag released before suspend. Later when system suspend is done, the stream tag for the remaining active stream is released by SOF driver. After system resume, hda codec driver restores the stream tag for the active pcm stream, but SOF goes to assign a new one, which now doesn't match with the stream tag used by codec driver, and this causes DMA to fail receiving data, leading to unrecoverable XRUN condition in FW. For stream tag is stored in both hda codec and SOF driver, it shouldn't be released only in SOF driver. This patch just keeps the stream information in dma data and checks whether there is a stored DMA data for stream resuming from S3 and restores it. And it also removes DMA data when the stream is released. Tested on Whiskey Lake platform. GitHub issue: https://github.com/thesofproject/sof/issues/1594Signed-off-by:
-
Shengjiu Wang authored
There is chip errata ERR008000, the reference doc is (https://www.nxp.com/docs/en/errata/IMX6DQCE.pdf), The issue is "While using ESAI transmit or receive and an underrun/overrun happens, channel swap may occur. The only recovery mechanism is to reset the ESAI." This issue exist in imx3/imx5/imx6(partial) series. In this commit add a tasklet to handle reset of ESAI after xrun happens to recover the channel swap. Signed-off-by:
Shengjiu Wang <shengjiu.wang@nxp.com> Acked-by:
Nicolin Chen <nicoleotsuka@gmail.com> Link: https://lore.kernel.org/r/326035cb99975361699d9ed748054b08bc06a341.1562842206.git.shengjiu.wang@nxp.comSigned-off-by:
-
Janusz Jankowski authored
Some codecs require BCLK to be on for some time, before sending any data. SOF can enable BCLK and then wait for guaranteed time, before starting DMA on SSP start. Signed-off-by:
Janusz Jankowski <janusz.jankowski@linux.intel.com> Signed-off-by:
-
Kai Vehmanen authored
When application goes through SUSPEND/STOP->PREPARE->START cycle, we should always reprogram the DAI link DMA to ensure it is in sync with the host PCM DMA. Use same state tracking logic to handle both restart and system resume flows. Use link_prepared field of 'struct hdac_ext_stream' to store the state, instead of adding redundant fields to SOF specific structs. Signed-off-by:
Kai Vehmanen <kai.vehmanen@linux.intel.com> Signed-off-by:
-
Guennadi Liakhovetski authored
Enabling MSI on HDA can fail, in which case the legacy PCI IRQ mode will be used. To make testing this mode easier add an "enable_msi" module parameter, which is only enabled if debugging is enabled too. Signed-off-by:
Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com> Signed-off-by:
-
Zhu Yingjiang authored
Remove the first clear WAKESTS, only one clear is needed during init chip. Signed-off-by:
Zhu Yingjiang <yingjiang.zhu@linux.intel.com> Signed-off-by:
-
Zhu Yingjiang authored
Unify resume code by using SOF common function hda_dsp_ctrl_init_chip() which can handle both HDA and non-HDA cases. Move code to reset stream-to-link mapping into hda_dsp_ctrl_init_chip(). Signed-off-by:
-
Zhu Yingjiang authored
Set the HDA stream position buffer during init chip. The position buffer needs to be set in both HDA codec and nocodec cases. Using SOF defined function and move it to common code. Signed-off-by:
-
Rander Wang authored
In commit 7d4f606c ("ALSA: hda - WAKEEN feature enabling for runtime pm"), legacy HD-A driver sets hda controller in reset mode after entering runtime-suspend. And when resuming from suspend mode, it checks hda controller & codec status to detect headphone hotplug event. Now this patch does the same job in SOF runtime pm functions. And we need to check all the non-hdmi codecs for some cases like playback with HDMI or capture with DMIC connected to dsp. In these cases, only controller is active and codecs are suspended, so codecs can't send unsolicited event to controller. The jack polling operation will activate codecs and unsolicited event can work even codecs become suspended later. Tested on whiskylake with hda codecs. Signed-off-by:
-
Rander Wang authored
Move the code for hda to one point Signed-off-by:
-
Keyon Jie authored
The ROM state is represented by the 24 LSB bits in the ROM status register, so the mask should be 0xffffff instead of 0xf. Signed-off-by:
Keyon Jie <yang.jie@linux.intel.com> Signed-off-by:
-
Fred Oh authored
Remove unused and no plan to use variable from suspend function. Signed-off-by:
Fred Oh <fred.oh@linux.intel.com> Signed-off-by:
-
Daniel Baluta authored
On i.MX8 data/heap/stack is kept in System RAM so do not ignore SRAM block types received from FW. Signed-off-by:
Daniel Baluta <daniel.baluta@nxp.com> Signed-off-by:
-
Daniel Baluta authored
Make sure to use the newly introduced function snd_sof_dsp_get_bar_index that converts the section type to appropriate BAR index. Signed-off-by:
-
Daniel Baluta authored
FW encapsulates information about section types (e.g DRAM, IRAM) inside module block header. This information can be used in order to correctly load the section to the appropriate place in memory. SOF Linux driver needs to know for each platform how to map the section type with the corresponding memory BAR. So, this patch introduces get_bar_index, a new operation inside snd_sof_dsp_ops. Intel platforms, usually load all the section in a contiguous memory area (usually denoted by sdev->mmio_bar) so things are relatively simple there. Anyhow, on i.MX8 IRAM and DRAM for example are mapped to distinct BARs. By default, if no get_bar function is provided the core implementation will always return sdev->mmio_bar so that there will be no need for a change to existing Intel code. Signed-off-by:
-
Kai Vehmanen authored
Increase the default timeout values for boot (100ms to 2sec) and IPC message sending (5ms to 500ms). The values should be overridden with values from platform data. There is no functional need to have such short timeouts as both boot and IPC send errors are considered fatal errors. More relaxed timeouts are convenient when running the driver on top of emulation such as QEMU. Signed-off-by:
-
Kai Vehmanen authored
Do not hardcode IPC timeout value in ipc.c, but rather use the timeout value configured during device probe. For platforms that do not override the IPC timeout, default value TIMEOUT_DEFAULT_IPC_MS has already been defined in core.c. Signed-off-by:
-
Kai Vehmanen authored
Remove duplicated code by using a common helper function to send the PCM_FREE IPC message to FW. Signed-off-by:
-
Kai Vehmanen authored
When application goes through SUSPEND/STOP->PREPARE->START cycle, we should always reprogram the SOF device to start DMA from a known state so that hw_ptr/appl_ptrs remain valid. This is expected by ALSA core as it resets the buffer state as part of prepare (see snd_pcm_do_prepare()). Fix the issue by forcing reconfiguration of the FW with STREAM_PCM_PARAMS in prepare(). Use combined logic to handle prepare and the existing flow to reprogram hw-params after system suspend. Without the fix, first call to pcm pointer() will return an invalid hw_ptr and application may immediately observe XRUN status, unless "start_threshold" SW parameter is set to maximum value by the application. Signed-off-by:
-
Pan Xiuli authored
If last_busy value is not set at runtime PM enable, the device will be suspend immediately after usage counter is 0. Set the last_busy value to make sure delay is working at first boot up. Signed-off-by:
Pan Xiuli <xiuli.pan@linux.intel.com> Signed-off-by:
Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by:
-
Christophe JAILLET authored
There is a typo in PCM1368A_MAX_SYSCLK, it should be PCM3168A_MAX_SYSCLK (1 and 3 switched in 3168) Signed-off-by:
-
- 22 Jul, 2019 2 commits
-
-
Charles Keepax authored
Read the configuration of the Madera ASoC driver from device tree. Signed-off-by:
Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20190722135209.30302-1-ckeepax@opensource.cirrus.comSigned-off-by:
-
Oleksandr Suvorov authored
If VDDA != VDDIO and any of them is greater than 3.1V, charge pump source can be assigned automatically [1]. [1] https://www.nxp.com/docs/en/data-sheet/SGTL5000.pdfSigned-off-by:
Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Reviewed-by:
Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by:
Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by:
Fabio Estevam <festevam@gmail.com> Link: https://lore.kernel.org/r/20190719100524.23300-7-oleksandr.suvorov@toradex.comSigned-off-by:
-
