- 07 Jan, 2021 22 commits
-
-
Jakub Kicinski authored
Heiner Kallweit says: ==================== r8169: improve RTL8168g PHY suspend quirk According to Realtek the ERI register 0x1a8 quirk is needed to work around a hw issue with the PHY on RTL8168g. The register needs to be changed before powering down the PHY. Currently we don't meet this requirement, however I'm not aware of any problems caused by this. Therefore I see the change as an improvement. The PHY driver has no means to access the chip ERI registers, therefore we have to intercept MDIO writes to the BMCR register. If the BMCR_PDOWN bit is going to be set, then let's apply the quirk before actually powering down the PHY. ==================== Link: https://lore.kernel.org/r/9303c2cf-c521-beea-c09f-63b5dfa91b9c@gmail.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Heiner Kallweit authored
According to Realtek the ERI register 0x1a8 quirk is needed to work around a hw issue with the PHY on RTL8168g. The register needs to be changed before powering down the PHY. Currently we don't meet this requirement, however I'm not aware of any problems caused by this. Therefore I see the change as an improvement. The PHY driver has no means to access the chip ERI registers, therefore we have to intercept MDIO writes to BMCR register. If the BMCR_PDOWN bit is going to be set, then let's apply the quirk before actually powering down the PHY. Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
-
Heiner Kallweit authored
No functional change here. We just move a code block to avoid a function forward declaration in a subsequent change. Signed-off-by:
-
Heiner Kallweit authored
Switch to lockdep_assert_held(_once), similar to what is being done in other subsystems. One advantage is that there's zero runtime overhead if lockdep support isn't enabled. Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/ccc40b9d-8ee0-43a1-5009-2cc95ca79c85@gmail.comSigned-off-by:
-
Florian Fainelli authored
BCM72116 features a 28nm integrated EPHY, add an entry to match this PHY OUI. Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Reviewed-by:
-
Jakub Kicinski authored
udp_tunnel_nic: post conversion cleanup It has been two releases since we added the common infra for UDP tunnel port offload, and we have not heard of any major issues. Remove the old direct driver NDOs completely, and perform minor simplifications in the tunnel drivers. Link: https://lore.kernel.org/r/20210106210637.1839662-1-kuba@kernel.orgSigned-off-by:
-
Jakub Kicinski authored
Move the NETIF_F_RX_UDP_TUNNEL_PORT feature check into udp_tunnel_nic_*_port() helpers, since they're always done right before the call. Add similar checks before calling the notifier. udp_tunnel_nic invokes the notifier without checking features which could result in some wasted cycles. Reviewed-by:
Alexander Duyck <alexanderduyck@fb.com> Reviewed-by:
Jacob Keller <jacob.e.keller@intel.com> Signed-off-by:
-
Jakub Kicinski authored
All UDP tunnel port management is now routed via udp_tunnel_nic infra directly. Remove the old callbacks. Reviewed-by:
-
Jakub Kicinski authored
udp_tunnel_nic handles REGISTER and UNREGISTER event, now that all drivers use that infra we can drop the event handling in the tunnel drivers. Reviewed-by:
-
Jakub Kicinski authored
All drivers use udp_tunnel_nic_*_port() helpers, prepare for NDO removal by invoking those helpers directly. The helpers are safe to call on all devices, they check if device has the UDP tunnel state initialized. Reviewed-by:
-
Florian Fainelli authored
All of the OF code that is used has stubbed and will compile and link just fine, keeping COMPILE_TEST is enough. Signed-off-by:
Randy Dunlap <rdunlap@infradead.org> Link: https://lore.kernel.org/r/20210106191546.1358324-1-f.fainelli@gmail.comSigned-off-by:
-
Jakub Kicinski authored
Sieng Piaw Liew says: ==================== bcm63xx_enet: major makeover of driver This patch series aim to improve the bcm63xx_enet driver by integrating the latest networking features, i.e. batched rx processing, BQL, build_skb, etc. The newer enetsw SoCs are found to be able to do unaligned rx DMA by adding NET_IP_ALIGN padding which, combined with these patches, improved packet processing performance by ~50% on BCM6328. Older non-enetsw SoCs still benefit mainly from rx batching. Performance improvement of ~30% is observed on BCM6333. The BCM63xx SoCs are designed for routers. As such, having BQL is beneficial as well as trivial to add. v3: * Simplify xmit_more patch by not moving around the code needlessly. * Fix indentation in xmit_more patch. * Fix indentation in build_skb patch. * Split rx ring cleanup patch from build_skb patch and precede build_skb patch for better understanding, as suggested by Florian Fainelli. v2: * Add xmit_more support and rx loop improvisation patches. * Moved BQL netdev_reset_queue() to bcm_enet_stop()/bcm_enetsw_stop() functions as suggested by Florian Fainelli. * Improved commit messages. ==================== Link: https://lore.kernel.org/r/20210106144208.1935-1-liew.s.piaw@gmail.comSigned-off-by:
-
Sieng Piaw Liew authored
Use existing rx processed count to track against budget, thereby making budget decrement operation redundant. rx_desc_count can be calculated outside the rx loop, making the loop a bit smaller. Signed-off-by:
Sieng Piaw Liew <liew.s.piaw@gmail.com> Acked-by:
-
Sieng Piaw Liew authored
We can increase the efficiency of rx path by using buffers to receive packets then build SKBs around them just before passing into the network stack. In contrast, preallocating SKBs too early reduces CPU cache efficiency. Check if we're in NAPI context when refilling RX. Normally we're almost always running in NAPI context. Dispatch to napi_alloc_frag directly instead of relying on netdev_alloc_frag which does the same but with the overhead of local_bh_disable/enable. Tested on BCM6328 320 MHz and iperf3 -M 512 to measure packet/sec performance. Included netif_receive_skb_list and NET_IP_ALIGN optimizations. Before: [ ID] Interval Transfer Bandwidth Retr [ 4] 0.00-10.00 sec 49.9 MBytes 41.9 Mbits/sec 197 sender [ 4] 0.00-10.00 sec 49.3 MBytes 41.3 Mbits/sec receiver After: [ ID] Interval Transfer Bandwidth Retr [ 4] 0.00-30.00 sec 171 MBytes 47.8 Mbits/sec 272 sender [ 4] 0.00-30.00 sec 170 MBytes 47.6 Mbits/sec receiver Signed-off-by:
-
Sieng Piaw Liew authored
The rx SKB ring use the same code for cleanup at various points. Combine them into a function to reduce lines of code. Signed-off-by:
-
Sieng Piaw Liew authored
Use netdev_alloc_skb_ip_align on newer SoCs with integrated switch (enetsw) when refilling RX. Increases packet processing performance by 30% (with netif_receive_skb_list). Non-enetsw SoCs cannot function with the extra pad so continue to use the regular netdev_alloc_skb. Tested on BCM6328 320 MHz and iperf3 -M 512 to measure packet/sec performance. Before: [ ID] Interval Transfer Bandwidth Retr [ 4] 0.00-30.00 sec 120 MBytes 33.7 Mbits/sec 277 sender [ 4] 0.00-30.00 sec 120 MBytes 33.5 Mbits/sec receiver After (+netif_receive_skb_list): [ 4] 0.00-30.00 sec 155 MBytes 43.3 Mbits/sec 354 sender [ 4] 0.00-30.00 sec 154 MBytes 43.1 Mbits/sec receiver Signed-off-by:
-
Sieng Piaw Liew authored
Support bulking hardware TX queue by using netdev_xmit_more(). Signed-off-by:
-
Sieng Piaw Liew authored
Add Byte Queue Limits support to reduce/remove bufferbloat in bcm63xx_enet. Signed-off-by:
-
Sieng Piaw Liew authored
Use netif_receive_skb_list to batch process rx skb. Tested on BCM6328 320 MHz using iperf3 -M 512, increasing performance by 12.5%. Before: [ ID] Interval Transfer Bandwidth Retr [ 4] 0.00-30.00 sec 120 MBytes 33.7 Mbits/sec 277 sender [ 4] 0.00-30.00 sec 120 MBytes 33.5 Mbits/sec receiver After: [ ID] Interval Transfer Bandwidth Retr [ 4] 0.00-30.00 sec 136 MBytes 37.9 Mbits/sec 203 sender [ 4] 0.00-30.00 sec 135 MBytes 37.7 Mbits/sec receiver Signed-off-by:
-
Kristian Evensen authored
When measuring the throughput (iperf3 + TCP) while routing on a not-so-powerful device (Mediatek MT7621, 880MHz CPU), I noticed that I achieved significantly lower speeds with QMI-based modems than for example a USB LAN dongle. The CPU was saturated in all of my tests. With the dongle I got ~300 Mbit/s, while I only measured ~200 Mbit/s with the modems. All offloads, etc. were switched off for the dongle, and I configured the modems to use QMAP (16k aggregation). The tests with the dongle were performed in my local (gigabit) network, while the LTE network the modems were connected to delivers 700-800 Mbit/s. Profiling the kernel revealed the cause of the performance difference. In qmimux_rx_fixup(), an SKB is allocated for each packet contained in the URB. This SKB has too little headroom, causing the check in skb_cow() (called from ip_forward()) to fail. pskb_expand_head() is then called and the SKB is reallocated. In the output from perf, I see that a significant amount of time is spent in pskb_expand_head() + support functions. In order to ensure that the SKB has enough headroom, this commit increases the amount of memory allocated in qmimux_rx_fixup() by LL_MAX_HEADER. The reason for using LL_MAX_HEADER and not a more accurate value, is that we do not know the type of the outgoing network interface. After making this change, I achieve the same throughput with the modems as with the dongle. Signed-off-by:
Kristian Evensen <kristian.evensen@gmail.com> Acked-by:
Bjørn Mork <bjorn@mork.no> Link: https://lore.kernel.org/r/20210106122403.1321180-1-kristian.evensen@gmail.comSigned-off-by:
-
Jakub Kicinski authored
Merge tag 'linux-can-next-for-5.12-20210106' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next Marc Kleine-Budde says: ==================== pull-request: can-next 2021-01-06 The first 16 patches are by me and target the tcan4x5x SPI glue driver for the m_can CAN driver. First there are a several cleanup commits, then the SPI regmap part is converted to 8 bits per word, to make it possible to use that driver on SPI controllers that only support the 8 bit per word mode (such as the SPI cores on the raspberry pi). Oliver Hartkopp contributes a patch for the CAN_RAW protocol. The getsockopt() for CAN_RAW_FILTER is changed to return -ERANGE if the filterset does not fit into the provided user space buffer. The last two patches are by Joakim Zhang and add wakeup support to the flexcan driver for the i.MX8QM SoC. The dt-bindings docs are extended to describe the added property. * tag 'linux-can-next-for-5.12-20210106' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next: can: flexcan: add CAN wakeup function for i.MX8QM dt-bindings: can: fsl,flexcan: add fsl,scu-index property to indicate a resource can: raw: return -ERANGE when filterset does not fit into user space buffer can: tcan4x5x: add support for half-duplex controllers can: tcan4x5x: rework SPI access can: tcan4x5x: add {wr,rd}_table can: tcan4x5x: add max_raw_{read,write} of 256 can: tcan4x5x: tcan4x5x_regmap: set reg_stride to 4 can: tcan4x5x: fix max register value can: tcan4x5x: tcan4x5x_regmap_init(): use spi as context pointer can: tcan4x5x: tcan4x5x_regmap_write(): remove not needed casts and replace 4 by sizeof can: tcan4x5x: rename regmap_spi_gather_write() -> tcan4x5x_regmap_gather_write() can: tcan4x5x: remove regmap async support can: tcan4x5x: tcan4x5x_bus: remove not needed read_flag_mask can: tcan4x5x: mark struct regmap_bus tcan4x5x_bus as constant can: tcan4x5x: move regmap code into seperate file can: tcan4x5x: rename tcan4x5x.c -> tcan4x5x-core.c can: tcan4x5x: beautify indention of tcan4x5x_of_match and tcan4x5x_id_table can: tcan4x5x: replace DEVICE_NAME by KBUILD_MODNAME ==================== Link: https://lore.kernel.org/r/20210107094900.173046-1-mkl@pengutronix.deSigned-off-by:
-
Rafał Miłecki authored
Looking for an -EINVAL all over the dsa code could take hours for inexperienced DSA users. Signed-off-by:
Rafał Miłecki <rafal@milecki.pl> Reviewed-by:
-
- 06 Jan, 2021 18 commits
-
-
Joakim Zhang authored
The System Controller Firmware (SCFW) is a low-level system function which runs on a dedicated Cortex-M core to provide power, clock, and resource management. It exists on some i.MX8 processors. e.g. i.MX8QM (QM, QP), and i.MX8QX (QXP, DX). SCU driver manages the IPC interface between host CPU and the SCU firmware running on M4. For i.MX8QM, stop mode request is controlled by System Controller Unit(SCU) firmware, this patch introduces FLEXCAN_QUIRK_SETUP_STOP_MODE_SCFW quirk for this function. Signed-off-by:
Joakim Zhang <qiangqing.zhang@nxp.com> Link: https://lore.kernel.org/r/20201106105627.31061-6-qiangqing.zhang@nxp.comSigned-off-by:
Marc Kleine-Budde <mkl@pengutronix.de>
-
Joakim Zhang authored
For SoCs with SCU support, need setup stop mode via SCU firmware, so this property can help indicate a resource in SCU firmware. Signed-off-by:
-
Oliver Hartkopp authored
Multiple filters (struct can_filter) can be set with the setsockopt() function, which was originally intended as a write-only operation. As getsockopt() also provides a CAN_RAW_FILTER option to read back the given filters, the caller has to provide an appropriate user space buffer. In the case this buffer is too small the getsockopt() silently truncates the filter information and gives no information about the needed space. This is safe but not convenient for the programmer. In net/core/sock.c the SO_PEERGROUPS sockopt had a similar requirement and solved it by returning -ERANGE in the case that the provided data does not fit into the given user space buffer and fills the required size into optlen, so that the caller can retry with a matching buffer length. This patch adopts this approach for CAN_RAW_FILTER getsockopt(). Reported-by:
Phillip Schichtel <phillip@schich.tel> Signed-off-by:
Oliver Hartkopp <socketcan@hartkopp.net> Tested-By:
-
Marc Kleine-Budde authored
This patch adds back support for half-duplex controllers, which was removed in the last patch. Reviewed-by:
Dan Murphy <dmurphy@ti.com> Tested-by:
Sean Nyekjaer <sean@geanix.com> Link: https://lore.kernel.org/r/20201215231746.1132907-17-mkl@pengutronix.deSigned-off-by:
-
Marc Kleine-Budde authored
This patch reworks the SPI access and fixes several probems: - tcan4x5x_regmap_gather_write(), tcan4x5x_regmap_read(): Do not place variable "addr" on stack and use it as buffer for SPI transfer. Buffers for SPI transfers must be allocated from DMA save memory. - tcan4x5x_regmap_gather_write(), tcan4x5x_regmap_read(): Halfe number of SPI transfers by using a single buffer + memcpy(). This improves the performance, especially on SPI controllers, which use interrupt based transfers. - Use "8" bits per word, not "32". This makes it possible to use this driver on SoCs like the Raspberry Pi, which SPI host controller drivers only support 8 bits per word. Note: this breaks half duplex only controllers. Support for them will be re-added in the next patch. Reviewed-by:
-
Marc Kleine-Budde authored
The memory space of the chip is not fully populated, so add a regmap range table to document this. Reviewed-by:
-
Marc Kleine-Budde authored
The tcan4x5x chip support bulk read/write, but as the length field is only 8 bits wide, the maximum is 256. A length of 0 is treated as 256. Reviewed-by:
-
Marc Kleine-Budde authored
This patch sets the regmap stide to 4, as the chip only supports access on 32 bit alligned access. Reviewed-by:
-
Marc Kleine-Budde authored
This patch fixes the max register value for the regmap. Reviewed-by:
-
Marc Kleine-Budde authored
This patch replaces the context pointer of the regmap callback functions by a pointer to the spi_device. This saves one level of indirection in the callbacks. Reviewed-by:
-
Marc Kleine-Budde authored
This patch simplifies the tcan4x5x_regmap_write(0 function by removing not needed casts and replaces hardcoded "4" by appropriate sizeof()s. Reviewed-by:
-
Marc Kleine-Budde authored
This patch renames the regmap_spi_gather_write() function to tcan4x5x_regmap_gather_write(). Now it has a "tcan4x5x_" prefix as all other functions in this driver. Reviewed-by:
-
Marc Kleine-Budde authored
The driver doesn't use regmap async support, so remove the stubs. Reviewed-by:
-
Marc Kleine-Budde authored
With C99 initializers, all non mentioned members are initialzied to 0, so remove not needed initialization of read_flag_mask. Reviewed-by:
-
Marc Kleine-Budde authored
This patch marks the struct regmap_bus tcan4x5x_bus as constant. Reviewed-by:
-
Marc Kleine-Budde authored
This patch moves the regmap code into a seperate file. Reviewed-by:
-
Marc Kleine-Budde authored
This is a preparation patch to move the regmap related code into a seperate file. This patch removes the tcan4x5x.c to tcan4x5x-core.c. Reviewed-by:
-
Marc Kleine-Budde authored
This patch beautifies the indention of the tcan4x5x_of_match and tcan4x5x_id_table. Reviewed-by:
-
