We need to pay attention to ARP packets to correctly establish
connection, and reset the ARP counter when disconnected.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Before entering IPS, set the PTA control to default value and re-init it
after it leaves IPS to avoid running some redundant code in
run_coexist_mechanism.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

For newer coex mechanism, it is not necessary to set a critical value to
avoid the power on instability, just use default value for PTA.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When the wifi notifies the coexistence it is going to scan, set the coex
table to avoid issues when the scan result is empty.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When wifi is connected, use normal mode to set retry limit.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Adjust wifi slot time to tune the performance of coexistence
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Monitor if the wifi is softap mode, and set the tdma and coex table
accordingly.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

If wifi is not scanning, there may have some special and important
packets such as DHCP or EAPOL or ARP packets. Set tdma and coex table to
take care of them.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

If the wifi is scanning when connected, it is better if the slot
is shortened and the priority is increased. Otherwise bt a2dp may have
low quality.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Consider bt profiling is sco or hid to set coex table and tdma.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When wifi is idle, bt could have more resources to transmit, so set the
tdma and coex table to achieve this.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

PSD and LNA are for antenna detection, but we do not use them for 8821A.
Remove them and the corresponding display messages.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In the hardware initialisation stage, the PTA circuits may be unstable,
so we reset it after 6 secs to fix the problem.

dis_ver_info_cnt is used to indicate the time after init, and we can set
PTA according to it.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

We add some profiling combinations when the bt notifies the coex
mechanism to detect more situations and adjust the coex to fit to it.

Also monitor if the wifi is under 5G mode, if so, the signals do net
intefere each other, bt can just ignore it
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

If the wifi is leaving ips, re-init the coex mechanisms, and before it is
going into ips, the bt can just ignore the wifi activities.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The driver will periodically ask the coex, and the coex only runs the
mechanism when the status was changed or the auto adjust is set.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When driver is going to sleep, it does not leave LPS/IPS, thus the
BTCoex may have mismatch when driver wakes up. To avoid that, BTCoex
needs to clear the IPS/LPS state when it receives a pnp notify, then
it can properly set up the hw when driver wakes up.

Routine ex_btc8821a2ant_pnp_notify() restored.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Before firmware is ready, set GNT_BT to high to let bt transmit.

Routine ex_btc8821a2ant_pre_load_firmware() restored.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

If the wifi is going to halt or entering power saving, set it standby
and allocate resource to bt.

Routine btc8821a2ant_wifi_off_hw_cfg() restored.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

For hid a2dp profiling, decrease the bt power because of the distance of
bt is usually short, and do not adjust the wifi duration to a longer
period since it may be interrupted by bt easily, set tdma instead.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

if bt rssi is high, adjust the duration of wifi to a longer period to
let the wifi transmit under this bt profiling.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In file halbtc8192e2ant.c, there are directives that depend on an
undocumented configuration parameter BT_AUTO_REPORT_ONLY_8192E_2ANT
that cannot be set from Kconfig. This parameter is replaced by a
boolean in the main structure used by all routines. It still cannot
be changed dynamically, but it is easier to document.

Upon the advice of Realtek, the auto report option is turned on with
this patch.

Routine btc8192e2ant_is_wifi_status_changed() is restored.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In file halbtc8723b2ant.c, there are directives that depend on an
undocumented configuration parameter BT_AUTO_REPORT_ONLY_8723B_2ANT
that cannot be set from Kconfig. This parameter is replaced by a
boolean in the main structure used by all routines. It still cannot
be changed dynamically, but it is easier to document.

Routines halbtc8723b2ant_set_bt_auto_report(), and
btc8723b2ant_bt_auto_report() are restored.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In file halbtc8723b1ant.c, there are directives that depend on an
undocumented configuration parameter BT_AUTO_REPORT_ONLY_8723B_1ANT
that cannot be set from Kconfig. This parameter is replaced by a
boolean in the main structure used by all routines. It still cannot
be changed dynamically, but it is easier to document.

The following routines are restored:
halbtc8723b1ant_bt_auto_report()
halbtc8723b1ant_set_bt_auto_report()
halbtc8723b1ant_action_wifi_only()
halbtc8723b1ant_monitor_bt_enable_disable()
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In file halbtc8821a1ant.c, there are directives that depend on an
undocumented configuration parameter BT_AUTO_REPORT_ONLY_8821A_1ANT
that cannot be set from Kconfig. This parameter is replaced by a
boolean in the main structure used by all routines. It still cannot
be changed dynamically, but it is easier to document.

Using a suggestion from Realtek, the auto report is turned on with this
patch.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Use memdup_user() helper instead of open-coding to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Similar to the SDIO driver, we should implement this so that we will
automatically reset the device whenever there's a command timeout or
similar.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The non-atomic test + set is a little awkward here, and it technically
means we might double-schedule work unnecessarily. AFAICT, this is not
really a problem, since the extra "work" will be a no-op (the flag(s)
will be cleared by then), but it's still an anti-pattern.

Rewrite this to use the atomic test_and_set_bit() helper instead.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

P2p client act as a station, data will be queued by DA instead
of RA. This patch pass the sanity check, so that p2p client share
the same data path with infrastruction station mode.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

As pno module is providing scheduled scan functionality have it taking
care of setting related wiphy parameters as well.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Detect gscan support in firmware by doing pfn_gscan_cfg iovar with
invalid version.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Pull networking fixes from David Miller:

 1) Track alignment in BPF verifier so that legitimate programs won't be
    rejected on !CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS architectures.

 2) Make tail calls work properly in arm64 BPF JIT, from Deniel
    Borkmann.

 3) Make the configuration and semantics Generic XDP make more sense and
    don't allow both generic XDP and a driver specific instance to be
    active at the same time. Also from Daniel.

 4) Don't crash on resume in xen-netfront, from Vitaly Kuznetsov.

 5) Fix use-after-free in VRF driver, from Gao Feng.

 6) Use netdev_alloc_skb_ip_align() to avoid unaligned IP headers in
    qca_spi driver, from Stefan Wahren.

 7) Always run cleanup routines in BPF samples when we get SIGTERM, from
    Andy Gospodarek.

 8) The mdio phy code should bring PHYs out of reset using the shared
    GPIO lines before invoking bus->reset(). From Florian Fainelli.

 9) Some USB descriptor access endian fixes in various drivers from
    Johan Hovold.

10) Handle PAUSE advertisements properly in mlx5 driver, from Gal
    Pressman.

11) Fix reversed test in mlx5e_setup_tc(), from Saeed Mahameed.

12) Cure netdev leak in AF_PACKET when using timestamping via control
    messages. From Douglas Caetano dos Santos.

13) netcp doesn't support HWTSTAMP_FILTER_ALl, reject it. From Miroslav
    Lichvar.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
  ldmvsw: stop the clean timer at beginning of remove
  ldmvsw: unregistering netdev before disable hardware
  net: netcp: fix check of requested timestamping filter
  ipv6: avoid dad-failures for addresses with NODAD
  qed: Fix uninitialized data in aRFS infrastructure
  mdio: mux: fix device_node_continue.cocci warnings
  net/packet: fix missing net_device reference release
  net/mlx4_core: Use min3 to select number of MSI-X vectors
  macvlan: Fix performance issues with vlan tagged packets
  net: stmmac: use correct pointer when printing normal descriptor ring
  net/mlx5: Use underlay QPN from the root name space
  net/mlx5e: IPoIB, Only support regular RQ for now
  net/mlx5e: Fix setup TC ndo
  net/mlx5e: Fix ethtool pause support and advertise reporting
  net/mlx5e: Use the correct pause values for ethtool advertising
  vmxnet3: ensure that adapter is in proper state during force_close
  sfc: revert changes to NIC revision numbers
  net: ch9200: add missing USB-descriptor endianness conversions
  net: irda: irda-usb: fix firmware name on big-endian hosts
  net: dsa: mv88e6xxx: add default case to switch
  ...

Pull cifs fixes from Steve French:
 "A set of minor cifs fixes"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  [CIFS] Minor cleanup of xattr query function
  fs: cifs: transport: Use time_after for time comparison
  SMB2: Fix share type handling
  cifs: cifsacl: Use a temporary ops variable to reduce code length
  Don't delay freeing mids when blocked on slow socket write of request
  CIFS: silence lockdep splat in cifs_relock_file()

Shannon Nelson says:

====================
ldmvsw: port removal stability

Under heavy reboot stress testing we found a couple of timing issues
when removing the device that could cause the kernel great heartburn,
addressed by these two patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Stop the clean timer earlier to be sure there's no asynchronous
interference while stopping the port.

Orabug: 25748241
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When running LDom binding/unbinding test, kernel may panic
in ldmvsw_open(). It is more likely that because we're removing
the ldc connection before unregistering the netdev in vsw_port_remove(),
we set up a window of time where one process could be removing the
device while another trying to UP the device. This also sometimes causes
vio handshake error due to opening a device without closing it completely.
We should unregister the netdev before we disable the "hardware".

Orabug: 25980913, 25925306
Signed-off-by: Thomas Tai <thomas.tai@oracle.com>
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver doesn't support timestamping of all received packets and
should return error when trying to enable the HWTSTAMP_FILTER_ALL
filter.

Cc: WingMan Kwok <w-kwok2@ti.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox, mlx5 fixes 2017-05-12

This series contains some mlx5 fixes for net.
Please pull and let me know if there's any problem.

For -stable:
("net/mlx5e: Fix ethtool pause support and advertise reporting") kernels >= 4.8
("net/mlx5e: Use the correct pause values for ethtool advertising") kernels >= 4.8

v1->v2:
 Dropped statistics spinlock patch, it needs some extra work.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Every address gets added with TENTATIVE flag even for the addresses with
IFA_F_NODAD flag and dad-work is scheduled for them. During this DAD process
we realize it's an address with NODAD and complete the process without
sending any probe. However the TENTATIVE flags stays on the
address for sometime enough to cause misinterpretation when we receive a NS.
While processing NS, if the address has TENTATIVE flag, we mark it DADFAILED
and endup with an address that was originally configured as NODAD with
DADFAILED.

We can't avoid scheduling dad_work for addresses with NODAD but we can
avoid adding TENTATIVE flag to avoid this racy situation.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current memset is using incorrect type of variable, causing the
upper-half of the strucutre to be left uninitialized and causing:

  ethernet/qlogic/qed/qed_init_fw_funcs.c: In function 'qed_set_rfs_mode_disable':
  ethernet/qlogic/qed/qed_init_fw_funcs.c:993:3: error: '*((void *)&ramline+4)' is used uninitialized in this function [-Werror=uninitialized]

Fixes: d51e4af5 ("qed: aRFS infrastructure support")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>