The set-led command is eight bytes long and starts with a command byte
followed by six bytes of RGB data and ends with a byte encoding a
frequency (see iuu_led() and iuu_rgbf_fill_buffer()).

The led activity helpers had a few long-standing bugs which corrupted
the command packets by inserting a second command byte and thereby
offsetting the RGB data and dropping the frequency in non-xmas mode.

In xmas mode, a related off-by-one error left the frequency field
uninitialised.

Fixes: 60a8fc01 ("USB: add iuu_phoenix driver")
Reported-by: George Spelvin <lkml@sdf.org>
Link: https://lore.kernel.org/r/20200716085056.31471-1-johan@kernel.orgReviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Clean up the handling of special interfaces that either should be
ignored or that need a larger number of URBs.

Commit 66f092ed ("USB: serial: sierra: unify quirk handling logic")
replaced the previous is_blacklisted() and is_highmemory() helpers with
a single is_quirk() helper which made it even harder to understand what
the interface lists were used for.

Rename the interface-list struct, its members and the interface-lookup
helper and restructure the code somewhat in order to make it more
self-explanatory.

Link: https://lore.kernel.org/r/20200713153936.18032-1-johan@kernel.orgReviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

The port data is not exported to user space so use the in-kernel u8
type.

Link: https://lore.kernel.org/r/20200713105517.27796-6-johan@kernel.orgReviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Drop unnecessary packed attributes from structs without padding.

Link: https://lore.kernel.org/r/20200713105517.27796-5-johan@kernel.orgReviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Enable TIOCGICOUNT to allow reading out the (unused) interrupt counters
and error statistics.

Note that modem-status events are currently left unimplemented as they
appear to be buffered on at least CP2102 and therefore cannot be used to
implement TIOCMIWAIT.

Link: https://lore.kernel.org/r/20200713105517.27796-4-johan@kernel.orgReviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Add support for line-status events that specifically can be used to
detect and report parity errors.

Enable the device's event-insertion mode whenever input-parity checking
is requested. This will insert line and modem status events into the
data stream.

Note that modem-status changes appear to be buffered until a character
is received (at least on CP2102) and support is therefore left
unimplemented.

On at least one type of these chips (CP2102), line breaks are not
reported as expected either (regardless of whether SERIAL_BREAK_CHAR is
set) so do not enable event-mode when !IGNBRK is requested for now.

Link: https://lore.kernel.org/r/20200713105517.27796-3-johan@kernel.orgReviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Try to disable the serial interface in the unlikely event that generic
open() fails.

Link: https://lore.kernel.org/r/20200713105517.27796-2-johan@kernel.orgReviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Drop redundant URB transfer-buffer casts.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Drop the redundant extern keyword from function declarations in the
subsystem header file to improve readability (and make it easier to spot
the global variables).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

There's no need to include sysrq.h in the subsystem header.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Add inline sysrq break-handler dummy to allow the compiler to eliminate
further code when either console or sysrq support isn't enabled and to
clearly mark the two sysrq functions as belonging together.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Inline the dummy sysrq character handling when either console support or
magic-sysrq support isn't enabled to allow the compiler to eliminate
unused code.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Do not set the sysrq timestamp unless CONFIG_MAGIC_SYSRQ is enabled to
avoid unnecessary per-character processing for consoles.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Only set the sysrq timestamp for console ports to avoid having every
driver also check the console flag when processing incoming data.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Only the last NUL in a packet should be flagged as a break character,
for example, to avoid dropping unrelated characters when IGNBRK is set.

Also make sysrq work by consuming the break character instead of having
it immediately cancel the sysrq request, and by not processing it
prematurely to avoid triggering a sysrq based on an unrelated character
received in the same packet (which was received *before* the break).

Note that the break flag can be left set also for a packet received
immediately following a break and that and an ending NUL in such a
packet will continue to be reported as a break as there's no good way to
tell it apart from an actual break.

Tested on FT232R and FT232H.

Fixes: 72fda3ca ("USB: serial: ftd_sio: implement sysrq handling on break")
Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Clean up receive processing by dropping the character pointer and
keeping the length argument unchanged throughout the function.

Also make it more apparent that sysrq processing can consume a
characters by adding an explicit continue.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Use an unsigned type for the process-packet buffer argument and give it
a more apt name.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.

[1] https://www.kernel.org/doc/html/latest/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-throughSigned-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

On devices which do not support break signalling a break condition is
simulated by sending a NUL byte at the lowest possible speed. The break
condition will be 9 bit periods long (start bit and eight data bits),
but the transmission itself also includes the stop bit.

Add the missing safety margin of one bit which is intended to account
for timing differences, and fix up the corresponding comment.
Signed-off-by: Michael Hanselmann <public@hansmi.ch>
Link: https://lore.kernel.org/r/9909b288-294d-16b9-9f14-51eb79c63b6c@msgid.hansmi.ch
[ johan: amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>

CP210x hardware disables auto-RTS but leaves auto-CTS when in hardware
flow control mode and UART on cp210x hardware is disabled. When
re-opening the port, if auto-CTS is enabled on the cp210x, then auto-RTS
must be re-enabled in the driver.
Signed-off-by: Brant Merryman <brant.merryman@silabs.com>
Co-developed-by: Phu Luu <phu.luu@silabs.com>
Signed-off-by: Phu Luu <phu.luu@silabs.com>
Link: https://lore.kernel.org/r/ECCF8E73-91F3-4080-BE17-1714BC8818FB@silabs.com
[ johan: fix up tags and problem description ]
Fixes: 39a66b8d ("[PATCH] USB: CP2101 Add support for flow control")
Cc: stable <stable@vger.kernel.org>     # 2.6.12
Signed-off-by: Johan Hovold <johan@kernel.org>

Assign the .throttle and .unthrottle functions to be generic function
in the driver structure to prevent data loss that can otherwise occur
if the host does not enable USB throttling.
Signed-off-by: Brant Merryman <brant.merryman@silabs.com>
Co-developed-by: Phu Luu <phu.luu@silabs.com>
Signed-off-by: Phu Luu <phu.luu@silabs.com>
Link: https://lore.kernel.org/r/57401AF3-9961-461F-95E1-F8AFC2105F5E@silabs.com
[ johan: fix up tags ]
Fixes: 39a66b8d ("[PATCH] USB: CP2101 Add support for flow control")
Cc: stable <stable@vger.kernel.org>     # 2.6.12
Signed-off-by: Johan Hovold <johan@kernel.org>

A subset of all CH341 devices don't support a real break condition. This
fact is already used in the "ch341_detect_quirks" function. With this
change a quirk is implemented to simulate a break condition by
temporarily lowering the baud rate and sending a NUL byte.

The primary drawbacks of this approach are that the duration of the
break can't be controlled by userland and that data incoming during
a simulated break is corrupted.

The "TTY_DRIVER_HARDWARE_BREAK" serial driver flag was investigated as
an alternative. It's a driver-wide flag and would've required
significant changes to the serial and USB-serial driver frameworks to
expose it for individual USB-serial adapters.

Tested by sending a break condition and watching the TX pin using an
oscilloscope.
Signed-off-by: Michael Hanselmann <public@hansmi.ch>
Link: https://lore.kernel.org/r/f34a9b6e-ec2a-0873-e97b-2d5b2170e2ff@msgid.hansmi.ch
[ johan: condense info message ]
Signed-off-by: Johan Hovold <johan@kernel.org>

Add support for enabling hardware flow control using the 'r' command
line option.

This also avoids a W=1 (-Wunused-but-set-variable) warning.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Drop two unused stub functions which only served as documentation.

This also avoids a W=1 (-Wunused-but-set-variable) warning.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Log failure to update the line settings in set_termios().

This also avoids a W=1 (-Wunused-but-set-variable) warning.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Drop the unused firmware reset status which would already have been
logged.

This suppresses the corresponding W=1 (-Wunused-but-set-variable)
warning.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

The driver is submitting URBs in various completion callbacks without
bothering to log errors yet still assigned the return value to temporary
variables. Let's drop those temporaries.

This suppresses the corresponding W=1 (-Wunused-but-set-variable)
warnings.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

Don't compile the four unused packet definitions but keep them around
for documentation purposes.

This avoids the corresponding W=1 (-Wunused-const-variable) warning.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>

The line-speed algorithm clamps the requested value to the supported
range instead of bailing out on unsupported values.

Provide min and max macros and indicate how they are derived instead of
hardcoding the limits.

Note that the algorithm depends on the minimum rate (45.78 bps)
being rounded up (and the maximum rate being rounded down) to avoid
special casing.
Suggested-by: Michael Hanselmann <public@hansmi.ch>
Link: https://lore.kernel.org/r/20200630095756.GZ3334@localhostSigned-off-by: Johan Hovold <johan@kernel.org>

Add constants for the prescaler and divisor registers. Document and
name register 0x25, and put the LCR define to more use.

The 0x25 register (CH341_REG_LCR2) is only used by CH341 chips before
version 0x30 and is involved in configuring the line control parameters.
It's not known to the author whether there any such chips in the wild,
and Linux' ch341 driver never supported them. For chip version 0x30 and
above the 0x25 register is always set to zero. The alternative would've
been to not set the register at all, but that may have unintended
effects.
Signed-off-by: Michael Hanselmann <public@hansmi.ch>
Link: https://lore.kernel.org/r/2e80916d-1be8-dc0f-abf9-adc0feea1803@msgid.hansmi.ch
[ johan: fix up comment ]
Signed-off-by: Johan Hovold <johan@kernel.org>

We want the USB fixes in here, and this resolves a merge issue found in
linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull ARM OMAP fixes from Arnd Bergmann:
 "The OMAP developers are particularly active at hunting down
  regressions, so this is a separate branch with OMAP specific
  fixes for v5.8:

  As Tony explains
    "The recent display subsystem (DSS) related platform data changes
     caused display related regressions for suspend and resume. Looks
     like I only tested suspend and resume before dropping the legacy
     platform data, and forgot to test it after dropping it. Turns out
     the main issue was that we no longer have platform code calling
     pm_runtime_suspend for DSS like we did for the legacy platform data
     case, and that fix is still being discussed on the dri-devel list
     and will get merged separately. The DSS related testing exposed a
     pile other other display related issues that also need fixing
     though":

   - Fix ti-sysc optional clock handling and reset status checks for
     devices that reset automatically in idle like DSS

   - Ignore ti-sysc clockactivity bit unless separately requested to
     avoid unexpected performance issues

   - Init ti-sysc framedonetv_irq to true and disable for am4

   - Avoid duplicate DSS reset for legacy mode with dts data

   - Remove LCD timings for am4 as they cause warnings now that we're
     using generic panels

  Other OMAP changes from Tony include:

   - Fix omap_prm reset deassert as we still have drivers setting the
     pm_runtime_irq_safe() flag

   - Flush posted write for ti-sysc enable and disable

   - Fix droid4 spi related errors with spi flags

   - Fix am335x USB range and a typo for softreset

   - Fix dra7 timer nodes for clocks for IPU and DSP

   - Drop duplicate mailboxes after mismerge for dra7

   - Prevent pocketgeagle header line signal from accidentally setting
     micro-SD write protection signal by removing the default mux

   - Fix NFSroot flakeyness after resume for duover by switching the
     smsc911x gpio interrupt to back to level sensitive

   - Fix regression for omap4 clockevent source after recent system
     timer changes

   - Yet another ethernet regression fix for the "rgmii" vs "rgmii-rxid"
     phy-mode

   - One patch to convert am3/am4 DT files to use the regular sdhci-omap
     driver instead of the old hsmmc driver, this was meant for the
     merge window but got lost in the process"

* tag 'arm-omap-fixes-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (21 commits)
  ARM: dts: am5729: beaglebone-ai: fix rgmii phy-mode
  ARM: dts: Fix omap4 system timer source clocks
  ARM: dts: Fix duovero smsc interrupt for suspend
  ARM: dts: am335x-pocketbeagle: Fix mmc0 Write Protect
  Revert "bus: ti-sysc: Increase max softreset wait"
  ARM: dts: am437x-epos-evm: remove lcd timings
  ARM: dts: am437x-gp-evm: remove lcd timings
  ARM: dts: am437x-sk-evm: remove lcd timings
  ARM: dts: dra7-evm-common: Fix duplicate mailbox nodes
  ARM: dts: dra7: Fix timer nodes properly for timer_sys_ck clocks
  ARM: dts: Fix am33xx.dtsi ti,sysc-mask wrong softreset flag
  ARM: dts: Fix am33xx.dtsi USB ranges length
  bus: ti-sysc: Increase max softreset wait
  ARM: OMAP2+: Fix legacy mode dss_reset
  bus: ti-sysc: Fix uninitialized framedonetv_irq
  bus: ti-sysc: Ignore clockactivity unless specified as a quirk
  bus: ti-sysc: Use optional clocks on for enable and wait for softreset bit
  ARM: dts: omap4-droid4: Fix spi configuration and increase rate
  bus: ti-sysc: Flush posted write on enable and disable
  soc: ti: omap-prm: use atomic iopoll instead of sleeping one
  ...

Pull ARM SoC fixes from Arnd Bergmann:
 "Here are a couple of bug fixes, mostly for devicetree files

  NXP i.MX:
   - Use correct voltage on some i.MX8M board device trees to avoid
     hardware damage
   - Code fixes for a compiler warning and incorrect reference counting,
     both harmless.
   - Fix the i.MX8M SoC driver to correctly identify imx8mp
   - Fix watchdog configuration in imx6ul-kontron device tree.

  Broadcom:
   - A small regression fix for the Raspberry-Pi firmware driver
   - A Kconfig change to use the correct timer driver on Northstar
   - A DT fix for the Luxul XWC-2000 machine
   - Two more DT fixes for NSP SoCs

  STmicroelectronics STI
   - Revert one broken patch for L2 cache configuration

  ARM Versatile Express:
   - Fix a regression by reverting a broken DT cleanup

  TEE drivers:
   - MAINTAINERS: change tee mailing list"

* tag 'arm-fixes-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
  Revert "ARM: sti: Implement dummy L2 cache's write_sec"
  soc: imx8m: fix build warning
  ARM: imx6: add missing put_device() call in imx6q_suspend_init()
  ARM: imx5: add missing put_device() call in imx_suspend_alloc_ocram()
  soc: imx8m: Correct i.MX8MP UID fuse offset
  ARM: dts: imx6ul-kontron: Change WDOG_ANY signal from push-pull to open-drain
  ARM: dts: imx6ul-kontron: Move watchdog from Kontron i.MX6UL/ULL board to SoM
  arm64: dts: imx8mm-beacon: Fix voltages on LDO1 and LDO2
  arm64: dts: imx8mn-ddr4-evk: correct ldo1/ldo2 voltage range
  arm64: dts: imx8mm-evk: correct ldo1/ldo2 voltage range
  ARM: dts: NSP: Correct FA2 mailbox node
  ARM: bcm2835: Fix integer overflow in rpi_firmware_print_firmware_revision()
  MAINTAINERS: change tee mailing list
  ARM: dts: NSP: Disable PL330 by default, add dma-coherent property
  ARM: bcm: Select ARM_TIMER_SP804 for ARCH_BCM_NSP
  ARM: dts: BCM5301X: Add missing memory "device_type" for Luxul XWC-2000
  arm: dts: vexpress: Move mcc node back into motherboard node

Pull timer fix from Ingo Molnar:
 "A single DocBook fix"

* tag 'timers-urgent-2020-06-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timekeeping: Fix kerneldoc system_device_crosststamp & al

Pull perf fix from Ingo Molnar:
 "A single Kbuild dependency fix"

* tag 'perf-urgent-2020-06-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/rapl: Fix RAPL config variable bug

Pull EFI fixes from Ingo Molnar:

 - Fix build regression on v4.8 and older

 - Robustness fix for TPM log parsing code

 - kobject refcount fix for the ESRT parsing code

 - Two efivarfs fixes to make it behave more like an ordinary file
   system

 - Style fixup for zero length arrays

 - Fix a regression in path separator handling in the initrd loader

 - Fix a missing prototype warning

 - Add some kerneldoc headers for newly introduced stub routines

 - Allow support for SSDT overrides via EFI variables to be disabled

 - Report CPU mode and MMU state upon entry for 32-bit ARM

 - Use the correct stack pointer alignment when entering from mixed mode

* tag 'efi-urgent-2020-06-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  efi/libstub: arm: Print CPU boot mode and MMU state at boot
  efi/libstub: arm: Omit arch specific config table matching array on arm64
  efi/x86: Setup stack correctly for efi_pe_entry
  efi: Make it possible to disable efivar_ssdt entirely
  efi/libstub: Descriptions for stub helper functions
  efi/libstub: Fix path separator regression
  efi/libstub: Fix missing-prototype warning for skip_spaces()
  efi: Replace zero-length array and use struct_size() helper
  efivarfs: Don't return -EINTR when rate-limiting reads
  efivarfs: Update inode modification time for successful writes
  efi/esrt: Fix reference count leak in esre_create_sysfs_entry.
  efi/tpm: Verify event log header before parsing
  efi/x86: Fix build with gcc 4

Pull scheduler fixes from Borislav Petkov:
 "The most anticipated fix in this pull request is probably the horrible
  build fix for the RANDSTRUCT fail that didn't make -rc2. Also included
  is the cleanup that removes those BUILD_BUG_ON()s and replaces it with
  ugly unions.

  Also included is the try_to_wake_up() race fix that was first
  triggered by Paul's RCU-torture runs, but was independently hit by
  Dave Chinner's fstest runs as well"

* tag 'sched_urgent_for_5.8_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/cfs: change initial value of runnable_avg
  smp, irq_work: Continue smp_call_function*() and irq_work*() integration
  sched/core: s/WF_ON_RQ/WQ_ON_CPU/
  sched/core: Fix ttwu() race
  sched/core: Fix PI boosting between RT and DEADLINE tasks
  sched/deadline: Initialize ->dl_boosted
  sched/core: Check cpus_mask, not cpus_ptr in __set_cpus_allowed_ptr(), to fix mask corruption
  sched/core: Fix CONFIG_GCC_PLUGIN_RANDSTRUCT build fail

Pull x86 fixes from Borislav Petkov:

 - AMD Memory bandwidth counter width fix, by Babu Moger.

 - Use the proper length type in the 32-bit truncate() syscall variant,
   by Jiri Slaby.

 - Reinit IA32_FEAT_CTL during wakeup to fix the case where after
   resume, VMXON would #GP due to VMX not being properly enabled, by
   Sean Christopherson.

 - Fix a static checker warning in the resctrl code, by Dan Carpenter.

 - Add a CR4 pinning mask for bits which cannot change after boot, by
   Kees Cook.

 - Align the start of the loop of __clear_user() to 16 bytes, to improve
   performance on AMD zen1 and zen2 microarchitectures, by Matt Fleming.

* tag 'x86_urgent_for_5.8_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/asm/64: Align start of __clear_user() loop to 16-bytes
  x86/cpu: Use pinning mask for CR4 bits needing to be 0
  x86/resctrl: Fix a NULL vs IS_ERR() static checker warning in rdt_cdp_peer_get()
  x86/cpu: Reinitialize IA32_FEAT_CTL MSR on BSP during wakeup
  syscalls: Fix offset type of ksys_ftruncate()
  x86/resctrl: Fix memory bandwidth counter width for AMD

Pull RCU-vs-KCSAN fixes from Borislav Petkov:
 "A single commit that uses "arch_" atomic operations to avoid the
  instrumentation that comes with the non-"arch_" versions.

  In preparation for that commit, it also has another commit that makes
  these "arch_" atomic operations available to generic code.

  Without these commits, KCSAN uses can see pointless errors"

* tag 'rcu_urgent_for_5.8_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  rcu: Fixup noinstr warnings
  locking/atomics: Provide the arch_atomic_ interface to generic code