Signed-off-by: Giel van Schijndel <me@mortis.eu>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Fix debug macro line wrapping.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

On iEi PCISA-9652-R10 (BIOS version 1.5) single board computer reads
from the game port do not seem to reset the watchdog timer. This patch
adds a module parameter wdt_config_reg to specify alternative reset
sources. At least WDT_RESET_KBD has been tested, even just running

while true; do
    setleds -L +scroll
    sleep 1
    setleds -L -scroll
    sleep 1
done

is enough to keep the watchdog happy.
Signed-off-by: Timo Juhani Lindfors <timo.lindfors@iki.fi>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Signed-off-by: Timo Juhani Lindfors <timo.lindfors@iki.fi>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

This patch adds support for watchdogs with 8b timers, like ones in
IT8702F and older revisions of IT8712F Super IO chip, to it87_wdt
driver. This patch should be used after the patch
'it87_wdt: Add support for IT8720F watchdog'.
Signed-off-by: Ondrej Zajicek <santiago@crfreenet.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

This simple patch adds support for a watchdog in IT8720F Super IO chip
to it87_wdt driver.
Signed-off-by: Ondrej Zajicek <santiago@crfreenet.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

The current iTCO_wdt driver warnings are confusing.  Currently when the device
driver returns an error the console contains:

iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
iTCO_wdt: failed to reset NO_REBOOT flag, reboot disabled by hardware
iTCO_wdt: No card detected

After the patch,

iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
iTCO_wdt: failed to reset NO_REBOOT flag, device disabled by hardware/BIOS

Clean this up and use the word "device" to describe the device.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

This patch adds the Intel Patsburg (PCH) DeviceIDs for iTCO Watchdog.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Merge branch 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: Move olpc to platform
  x86: Move uv to platform
  x86: Move mrst to platform
  x86: Move scx200 to platform
  x86: Move visws to platform
  x86: Move efi to platform
  x86: Move sfi to platform
  x86: Add platform directory

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging: (68 commits)
  hwmon: (it87) Add support for the IT8721F/IT8758E
  hwmon: (it87) Move conversion functions
  hwmon: Remove many EXPERIMENTAL flags
  hwmon: (lm85) Add support for ADT7468 high-frequency PWM mode
  hwmon: (lm85) Document the ADT7468 as supported
  hwmon: (lm85) Fix ADT7468 frequency table
  hwmon: I2C addresses are constant
  Move ams driver to macintosh
  hwmon: (pcf8591) Don't attempt to detect devices
  hwmon: (pcf8591) Register as a hwmon device
  hwmon: (w83795) Use standard attributes for chassis intrusion
  hwmon: (w83795) Exclude fan control feature by default
  hwmon: (w83795) Add myself as co-author and maintainer
  hwmon: (w83795) More style cleanups
  hwmon: (w83795) Fix LSB reading of voltage limits
  hwmon: (w83795) Use dev_get_drvdata() where possible
  hwmon: (w83795) Delay reading pwm config registers
  hwmon: (w83795) Delay reading limit registers
  hwmon: (w83795) Move register reads to dedicated functions
  hwmon: (w83795) Pack similar register reads
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (841 commits)
  Staging: brcm80211: fix usage of roundup in structures
  Staging: bcm: fix up network device reference counting
  Staging: keucr: fix up US_ macro change
  staging: brcm80211: brcmfmac: Removed codeversion from firmware filenames.
  staging: brcm80211: Remove unnecessary header files.
  staging: brcm80211: Remove unnecessary includes from bcmutils.c
  staging: brcm80211: Removed unnecessary pktsetprio() function.
  Staging: brcm80211: remove typedefs.h
  Staging: brcm80211: remove uintptr typedef usage
  Staging: hv: remove struct vmbus_channel_interface
  Staging: hv: remove Open from struct vmbus_channel_interface
  Staging: hv: storvsc: call vmbus_open directly
  Staging: hv: netvsc: call vmbus_open directly
  Staging: hv: channel: export vmbus_open to modules
  Staging: hv: remove Close from struct vmbus_channel_interface
  Staging: hv: netvsc: call vmbus_close directly
  Staging: hv: storvsc: call vmbus_close directly
  Staging: hv: channel: export vmbus_close to modules
  Staging: hv: remove SendPacket from struct vmbus_channel_interface
  Staging: hv: storvsc: call vmbus_sendpacket directly
  ...

Fix up conflicts in
	drivers/staging/cx25821/cx25821-audio-upstream.c
	drivers/staging/cx25821/cx25821-audio.h
due to warring whitespace cleanups (neither of which were all that great)

* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (32 commits)
  sh: intc: switch irq_desc iteration to new active IRQ iterator.
  sh: fix up cpu hotplug IRQ migration for irq_data changes.
  sh: oprofile: Make sure the backtrace op is available for timer-fallback.
  sh64: oprofile: Fix up kernel stack pointer size mismatch.
  sh: oprofile: Fix up and extend op_name_from_perf_id().
  sh: lockless get_user_pages_fast()
  sh64: _PAGE_SPECIAL support.
  sound: sh: ctrl_in/outX to __raw_read/writeX conversion.
  sh: disable deprecated genirq support.
  sh: update show_interrupts() for irq_data chip lookup.
  sh: intc: irq_data conversion.
  sh64: irq_data conversion.
  sh64: update for IRQ flag handling naming changes.
  rtc: rtc-rs5c313: ctrl_in/outX to __raw_read/writeX conversion.
  sh: mach-se: irq_data conversion.
  input: hp680_ts_input: ctrl_in/outX to __raw_read/writeX conversion.
  input: jornada680_kbd: ctrl_in/outX to __raw_read/writeX conversion.
  sh: hd64461: irq_data conversion.
  sh: mach-x3proto: irq_data conversion.
  sh: mach-systemh: irq_data conversion.
  ...

* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (27 commits)
  x86: allocate space within a region top-down
  x86: update iomem_resource end based on CPU physical address capabilities
  x86/PCI: allocate space from the end of a region, not the beginning
  PCI: allocate bus resources from the top down
  resources: support allocating space within a region from the top down
  resources: handle overflow when aligning start of available area
  resources: ensure callback doesn't allocate outside available space
  resources: factor out resource_clip() to simplify find_resource()
  resources: add a default alignf to simplify find_resource()
  x86/PCI: MMCONFIG: fix region end calculation
  PCI: Add support for polling PME state on suspended legacy PCI devices
  PCI: Export some PCI PM functionality
  PCI: fix message typo
  PCI: log vendor/device ID always
  PCI: update Intel chipset names and defines
  PCI: use new ccflags variable in Makefile
  PCI: add PCI_MSIX_TABLE/PBA defines
  PCI: add PCI vendor id for STmicroelectronics
  x86/PCI: irq and pci_ids patch for Intel Patsburg DeviceIDs
  PCI: OLPC: Only enable PCI configuration type override on XO-1
  ...

Add support for the IT8721F/IT8758E. These new chips differ from the
older IT87xxF chips in the following ways:
* ADC LSB is 12 mV instead of 16 mV.
* PWM values are 8-bit instead of 7-bit.
There are other minor changes we don't have to care about in the
driver.

Another change is that we will handle internal voltage scaling in the
driver instead of delegating the work to user-space.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Move conversion functions until after structure defintions. This is
needed for future changes which make use of the structures in the
conversion funtcions.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Remove the dependency on EXPERIMENTAL for all drivers which are in
the kernel tree for a long time, are known to work properly and for
which we have documentation.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Corentin Labbe <corentin.labbe@geomatys.fr>
Cc: Riku Voipio <riku.voipio@iki.fi>
Cc: Juerg Haefliger <juergh@gmail.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>

The ADT7468 supports a high-frequency PWM output mode where all PWM
outputs are driven by a 22.5 kHz clock. Add support for this mode, and
document it, as it may surprise the user that setting one PWM output
frequency also affects the other PWM outputs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>

The ADT7468 uses the same frequency table as the ADT7463.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Cc: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>

We can mark normal_i2c const. Almost all drivers do that already, so
fix the 3 remaining ones before they are used as (bad) examples for
new drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: George Joseph <george.joseph@fairview5.com>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>

The ams driver isn't a hardware monitoring driver, so it shouldn't
live under driver/hwmon. drivers/macintosh seems much more
appropriate, as the driver is only useful on PowerBooks and iBooks.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Stelian Pop <stelian@popies.net>
Cc: Michael Hanselmann <linux-kernel@hansmi.ch>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>

The PCF8591 can't be detected, don't even try. There are plenty of
other means to instantiate i2c devices these days.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>

Register PCF8591 devices as hwmon devices. There's little point in
implementing the standard sysfs interface if we don't register it in
a way libsensors will pick it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>

Follow the standard attribute naming for the chassis intrusion
feature. I couldn't test the beeping (my board apparently doesn't do
that) but the alarm works fine.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>

The fan control feature of the w83795 driver is insufficiently
reviewed and tested for public consumption at this time, so make it
optional and disabled by default. We will change the default when
review and testing is deemed sufficient. Ultimately the option will
go away.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>

I've made so many changes to the w83795 driver that it's only fair to
list myself as a co-author. I'll also maintain the driver for some
time. There's more work needed on the driver for sure.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>

Cleanups suggested by Guenter Roeck, falling into 4 categories:
* Swapping test orders, because if (var == CONSTANT) is much easier to
  read than if (CONSTANT == var).
* Simplifying comparisons with 0.
* Dropping unneeded masks.
* Dropping unneeded parentheses and curly braces.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>

Wrong index caused the wrong register value to be read, resulting in
random LSB for voltage limits.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

When we don't need the client pointer, calling dev_get_drvdata() is
more efficient that calling to_i2c_client() and then
i2c_get_clientdata().
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Wait until we need the pwm config register values, instead of
pre-reading them. This saves over 1 second on modprobe on my test
system.

Obviously this time is added when first accessing pwm config
attributes, however not everybody will use them, so it seems unfair
to slow down driver loading (and thus boot) for an optional feature.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Wait until we need the limit register values, instead of pre-reading
them. This saves 544 ms on modprobe on my test system. Obviously this
time is added when first running "sensors" or any other monitoring
application, but I think it is better than slowing down the boot.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Move initial register reads out of probe, to dedicated functions.
This makes the code clearer, and will be needed if we want to delay
calling these functions until they are needed, or want to call them
periodically.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>

Pack similar register reads using for loops.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Cascaded conditionals are inefficient. Reorder the fields so that
PWM register addresses can be computed more efficiently.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>

There is no point in reading registers during initialization if we
will refresh the values in the update function later. This is only
slowing down the driver loading with no benefit, stop doing it.
This change saves 480 ms on driver load on my test system.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

All 3 temperature sensor type sysfs functions (show_temp_mode,
store_temp_mode and show_dts_mode) can be simplified. We don't
create these files when the correponding input isn't in temperature
monitoring mode, so there is no point in handling that case.
Likewise, we don't allow changing inputs from temperature to voltage,
so the code handling this case is dead and can be removed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Consistently use ARRAY_SIZE() to control for loops.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Get rid of REST_VLT_BEGIN and REST_VLT_END, they don't make the code
more readable.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

x % 1 is obviously wrong, as it always evaluates to 0. You want
x % 2, or x & 1, for parity checking.
Signed-off-by: Jean Delvare <khali@linux-fr.org>