Pull crypto fixes from Herbert Xu:

 - self-test failure of crc32c on powerpc

 - regressions of ecb(aes) when used with xts/lrw in s5p-sss

 - a number of bugs in the omap RNG driver

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: s5p-sss - Fix spinlock recursion on LRW(AES)
  hwrng: omap - Do not access INTMASK_REG on EIP76
  hwrng: omap - use devm_clk_get() instead of of_clk_get()
  hwrng: omap - write registers after enabling the clock
  crypto: s5p-sss - Fix completing crypto request in IRQ handler
  crypto: powerpc - Fix initialisation of crc32c context

Pull networking fixes from David Miller:

 1) Ensure that mtu is at least IPV6_MIN_MTU in ipv6 VTI tunnel driver,
    from Steffen Klassert.

 2) Fix crashes when user tries to get_next_key on an LPM bpf map, from
    Alexei Starovoitov.

 3) Fix detection of VLAN fitlering feature for bnx2x VF devices, from
    Michal Schmidt.

 4) We can get a divide by zero when TCP socket are morphed into
    listening state, fix from Eric Dumazet.

 5) Fix socket refcounting bugs in skb_complete_wifi_ack() and
    skb_complete_tx_timestamp(). From Eric Dumazet.

 6) Use after free in dccp_feat_activate_values(), also from Eric
    Dumazet.

 7) Like bonding team needs to use ETH_MAX_MTU as netdev->max_mtu, from
    Jarod Wilson.

 8) Fix use after free in vrf_xmit(), from David Ahern.

 9) Don't do UDP Fragmentation Offload on IPComp ipsec packets, from
    Alexey Kodanev.

10) Properly check napi_complete_done() return value in order to decide
    whether to re-enable IRQs or not in amd-xgbe driver, from Thomas
    Lendacky.

11) Fix double free of hwmon device in marvell phy driver, from Andrew
    Lunn.

12) Don't crash on malformed netlink attributes in act_connmark, from
    Etienne Noss.

13) Don't remove routes with a higher metric in ipv6 ECMP route replace,
    from Sabrina Dubroca.

14) Don't write into a cloned SKB in ipv6 fragmentation handling, from
    Florian Westphal.

15) Fix routing redirect races in dccp and tcp, basically the ICMP
    handler can't modify the socket's cached route in it's locked by the
    user at this moment. From Jon Maxwell.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (108 commits)
  qed: Enable iSCSI Out-of-Order
  qed: Correct out-of-bound access in OOO history
  qed: Fix interrupt flags on Rx LL2
  qed: Free previous connections when releasing iSCSI
  qed: Fix mapping leak on LL2 rx flow
  qed: Prevent creation of too-big u32-chains
  qed: Align CIDs according to DORQ requirement
  mlxsw: reg: Fix SPVMLR max record count
  mlxsw: reg: Fix SPVM max record count
  net: Resend IGMP memberships upon peer notification.
  dccp: fix memory leak during tear-down of unsuccessful connection request
  tun: fix premature POLLOUT notification on tun devices
  dccp/tcp: fix routing redirect race
  ucc/hdlc: fix two little issue
  vxlan: fix ovs support
  net: use net->count to check whether a netns is alive or not
  bridge: drop netfilter fake rtable unconditionally
  ipv6: avoid write to a possibly cloned skb
  net: wimax/i2400m: fix NULL-deref at probe
  isdn/gigaset: fix NULL-deref at probe
  ...

Pull cgroup fixes from Tejun Heo:
 "Three cgroup fixes.  Nothing critical:

   - the pids controller could trigger suspicious RCU warning
     spuriously. Fixed.

   - in the debug controller, %p -> %pK to protect kernel pointer
     from getting exposed.

   - documentation formatting fix"

* 'for-4.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroups: censor kernel pointer in debug files
  cgroup/pids: remove spurious suspicious RCU usage warning
  cgroup: Fix indenting in PID controller documentation

Pull libata fixes from Tejun Heo:
 "Three libata fixes:

   - fix for a circular reference bug in sysfs code which prevented
     pata_legacy devices from being released after probe failure, which
     in turn prevented devres from releasing the associated resources.

   - drop spurious WARN in the command issue path which can be triggered
     by a legitimate passthrough command.

   - an ahci_qoriq specific fix"

* 'for-4.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  ahci: qoriq: correct the sata ecc setting error
  libata: drop WARN from protocol error in ata_sff_qc_issue()
  libata: transport: Remove circular dependency at free time

Pull workqueue fix from Tejun Heo:
 "If a delayed work is queued with NULL @wq, workqueue code explodes
  after the timer expires at which point it's difficult to tell who the
  culprit was.

  This actually happened and the offender was net/smc this time.

  Add an explicit sanity check for it in the queueing path"

* 'for-4.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
  workqueue: trigger WARN if queue_delayed_work() is called with NULL @wq

Pull percpu fixes from Tejun Heo:

 - the allocation path was updating pcpu_nr_empty_pop_pages without the
   required locking which can lead to incorrect handling of empty chunks
   (e.g. keeping too many around), which is buggy but shouldn't lead to
   critical failures. Fixed by adding the locking

 - a trivial patch to drop an unused param from pcpu_get_pages()

* 'for-4.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
  percpu: remove unused chunk_alloc parameter from pcpu_get_pages()
  percpu: acquire pcpu_lock when updating pcpu_nr_empty_pop_pages

Yuval Mintz says:

====================
qed: Fixes series

This address several different issues in qed.
The more significant portions:

Patch #1 would cause timeout when qedr utilizes the highest
CIDs availble for it [or when future qede adapters would utilize
queues in some constellations].

Patch #4 fixes a leak of mapped addresses; When iommu is enabled,
offloaded storage protocols might eventually run out of resources
and fail to map additional buffers.

Patches #6,#7 were missing in the initial iSCSI infrastructure
submissions, and would hamper qedi's stability when it reaches
out-of-order scenarios.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Missing in the initial submission, qed fails to propagate qedi's
request to enable OOO to firmware.

Fixes: fc831825 ("qed: Add support for hardware offloaded iSCSI")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Need to set the number of entries in database, otherwise the logic
would quickly surpass the array.

Fixes: 1d6cff4f ("qed: Add iSCSI out of order packet handling")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before iterating over the the LL2 Rx ring, the ring's
spinlock is taken via spin_lock_irqsave().
The actual processing of the packet [including handling
by the protocol driver] is done without said lock,
so qed releases the spinlock and re-claims it afterwards.

Problem is that the final spin_lock_irqrestore() at the end
of the iteration uses the original flags saved from the
initial irqsave() instead of the flags from the most recent
irqsave(). So it's possible that the interrupt status would
be incorrect at the end of the processing.

Fixes: 0a7fb11c ("qed: Add Light L2 support");
CC: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes: fc831825 ("qed: Add support for hardware offloaded iSCSI")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When receiving an Rx LL2 packet, qed fails to unmap the previous buffer.

Fixes: 0a7fb11c ("qed: Add Light L2 support");
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current Logic would allow the creation of a chain with U32_MAX + 1
elements, when the actual maximum supported by the driver infrastructure
is U32_MAX.

Fixes: a91eb52a ("qed: Revisit chain implementation")
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Doorbell HW block can be configured at a granularity
of 16 x CIDs, so we need to make sure that the actual number
of CIDs configured would be a multiplication of 16.

Today, when RoCE is enabled - given that the number is unaligned,
doorbelling the higher CIDs would fail to reach the firmware and
would eventually timeout.

Fixes: dbb799c3 ("qed: Initialize hardware for new protocols")
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw: Couple of fixes

Couple or small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The num_rec field is 8 bit, so the maximal count number is 255.
This fixes vlans learning not being enabled for wider ranges than 255.

Fixes: a4feea74 ("mlxsw: reg: Add Switch Port VLAN MAC Learning register definition")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The num_rec field is 8 bit, so the maximal count number is 255. This
fixes vlans not being enabled for wider ranges than 255.

Fixes: b2e345f9 ("mlxsw: reg: Add Switch Port VID and Switch Port VLAN Membership registers definitions")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we notify peers of potential changes,  it's also good to update
IGMP memberships.  For example, during VM migration, updating IGMP
memberships will redirect existing multicast streams to the VM at the
new location.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes a memory leak, which happens if the connection request
is not fulfilled between parsing the DCCP options and handling the SYN
(because e.g. the backlog is full), because we forgot to free the
list of ack vectors.
Reported-by: Jianwen Ji <jiji@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

aszlig observed failing ssh tunnels (-w) during initialization since
commit cc9da6cc ("ipv6: addrconf: use stable address generator for
ARPHRD_NONE"). We already had reports that the mentioned commit breaks
Juniper VPN connections. I can't clearly say that the Juniper VPN client
has the same problem, but it is worth a try to hint to this patch.

Because of the early generation of link local addresses, the kernel now
can start asking for routers on the local subnet much earlier than usual.
Those router solicitation packets arrive inside the ssh channels and
should be transmitted to the tun fd before the configuration scripts
might have upped the interface and made it ready for transmission.

ssh polls on the interface and receives back a POLL_OUT. It tries to send
the earily router solicitation packet to the tun interface.  Unfortunately
it hasn't been up'ed yet by config scripts, thus failing with -EIO. ssh
doesn't retry again and considers the tun interface broken forever.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=121131
Fixes: cc9da6cc ("ipv6: addrconf: use stable address generator for ARPHRD_NONE")
Cc: Bjørn Mork <bjorn@mork.no>
Reported-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Cc: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Reported-by: Jonas Lippuner <jonas@lippuner.ca>
Cc: Jonas Lippuner <jonas@lippuner.ca>
Reported-by: aszlig <aszlig@redmoonstudios.org>
Cc: aszlig <aszlig@redmoonstudios.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

As Eric Dumazet pointed out this also needs to be fixed in IPv6.
v2: Contains the IPv6 tcp/Ipv6 dccp patches as well.

We have seen a few incidents lately where a dst_enty has been freed
with a dangling TCP socket reference (sk->sk_dst_cache) pointing to that
dst_entry. If the conditions/timings are right a crash then ensues when the
freed dst_entry is referenced later on. A Common crashing back trace is:

 #8 [] page_fault at ffffffff8163e648
    [exception RIP: __tcp_ack_snd_check+74]
.
.
 #9 [] tcp_rcv_established at ffffffff81580b64
#10 [] tcp_v4_do_rcv at ffffffff8158b54a
#11 [] tcp_v4_rcv at ffffffff8158cd02
#12 [] ip_local_deliver_finish at ffffffff815668f4
#13 [] ip_local_deliver at ffffffff81566bd9
#14 [] ip_rcv_finish at ffffffff8156656d
#15 [] ip_rcv at ffffffff81566f06
#16 [] __netif_receive_skb_core at ffffffff8152b3a2
#17 [] __netif_receive_skb at ffffffff8152b608
#18 [] netif_receive_skb at ffffffff8152b690
#19 [] vmxnet3_rq_rx_complete at ffffffffa015eeaf [vmxnet3]
#20 [] vmxnet3_poll_rx_only at ffffffffa015f32a [vmxnet3]
#21 [] net_rx_action at ffffffff8152bac2
#22 [] __do_softirq at ffffffff81084b4f
#23 [] call_softirq at ffffffff8164845c
#24 [] do_softirq at ffffffff81016fc5
#25 [] irq_exit at ffffffff81084ee5
#26 [] do_IRQ at ffffffff81648ff8

Of course it may happen with other NIC drivers as well.

It's found the freed dst_entry here:

 224 static bool tcp_in_quickack_mode(struct sock *sk)↩
 225 {↩
 226 ▹       const struct inet_connection_sock *icsk = inet_csk(sk);↩
 227 ▹       const struct dst_entry *dst = __sk_dst_get(sk);↩
 228 ↩
 229 ▹       return (dst && dst_metric(dst, RTAX_QUICKACK)) ||↩
 230 ▹       ▹       (icsk->icsk_ack.quick && !icsk->icsk_ack.pingpong);↩
 231 }↩

But there are other backtraces attributed to the same freed dst_entry in
netfilter code as well.

All the vmcores showed 2 significant clues:

- Remote hosts behind the default gateway had always been redirected to a
different gateway. A rtable/dst_entry will be added for that host. Making
more dst_entrys with lower reference counts. Making this more probable.

- All vmcores showed a postitive LockDroppedIcmps value, e.g:

LockDroppedIcmps                  267

A closer look at the tcp_v4_err() handler revealed that do_redirect() will run
regardless of whether user space has the socket locked. This can result in a
race condition where the same dst_entry cached in sk->sk_dst_entry can be
decremented twice for the same socket via:

do_redirect()->__sk_dst_check()-> dst_release().

Which leads to the dst_entry being prematurely freed with another socket
pointing to it via sk->sk_dst_cache and a subsequent crash.

To fix this skip do_redirect() if usespace has the socket locked. Instead let
the redirect take place later when user space does not have the socket
locked.

The dccp/IPv6 code is very similar in this respect, so fixing it there too.

As Eric Garver pointed out the following commit now invalidates routes. Which
can set the dst->obsolete flag so that ipv4_dst_check() returns null and
triggers the dst_release().

Fixes: ceb33206 ("ipv4: Kill routes during PMTU/redirect updates.")
Cc: Eric Garver <egarver@redhat.com>
Cc: Hannes Sowa <hsowa@redhat.com>
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1. modify bd_status from u32 to u16 in function hdlc_rx_done,
because bd_status register is 16bits
2. write bd_length register before writing bd_status register
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull some more powerpc fixes from Michael Ellerman:
 "The main item is the addition of the Power9 Machine Check handler.
  This was delayed to make sure some details were correct, and is as
  minimal as possible.

  The rest is small fixes, two for the Power9 PMU, two dealing with
  obscure toolchain problems, two for the PowerNV IOMMU code (used by
  VFIO), and one to fix a crash on 32-bit machines with macio devices
  due to missing dma_ops.

  Thanks to:
    Alexey Kardashevskiy, Cyril Bur, Larry Finger, Madhavan Srinivasan,
    Nicholas Piggin"

* tag 'powerpc-4.11-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/64s: POWER9 machine check handler
  powerpc/64s: allow machine check handler to set severity and initiator
  powerpc/64s: fix handling of non-synchronous machine checks
  powerpc/pmac: Fix crash in dma-mapping.h with NULL dma_ops
  powerpc/powernv/ioda2: Update iommu table base on ownership change
  powerpc/powernv/ioda2: Gracefully fail if too many TCE levels requested
  selftests/powerpc: Replace stxvx and lxvx with stxvd2x/lxvd2x
  powerpc/perf: Handle sdar_mode for marked event in power9
  powerpc/perf: Fix perf_get_data_addr() for power9 DD1
  powerpc/boot: Fix zImage TOC alignment

The required changes in the function vxlan_dev_create() were missing
in commit 8bcdc4f3.
The vxlan device is not registered anymore after this patch and the error
path causes an stack dump:
 WARNING: CPU: 3 PID: 1498 at net/core/dev.c:6713 rollback_registered_many+0x9d/0x3f0

Fixes: 8bcdc4f3 ("vxlan: add changelink support")
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The previous idea was to check whether a net namespace is in
net_exit_list or not. It doesn't work, because net->exit_list is used in
__register_pernet_operations and __unregister_pernet_operations where
all namespaces are added to a temporary list to make cleanup in a error
case, so list_empty(&net->exit_list) always returns false.
Reported-by: Mantas Mikulėnas <grawity@gmail.com>
Fixes: 002d8a1a ("net: skip genenerating uevents for network namespaces that are exiting")
Signed-off-by: Andrei Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull x86 platform driver updates from Darren Hart:
 "Asus fixes for the airplane LED and a long awaited fujitsu cleanup.

  asus-wmi:
   - Remove quirk_no_rfkill
   - Detect quirk_no_rfkill from the DSDT

  fujitsu-laptop:
   - remove redundant MODULE_ALIAS entries
   - autodetect LCD interface on all models
   - simplify acpi_bus_register_driver() error handling
   - remove redundant forward declarations
   - replace numeric values with constants
   - rename FUNC_RFKILL to FUNC_FLAGS
   - make platform-related variables match naming convention
   - replace "hotkey" with "laptop" in symbol names
   - clearly denote backlight-related symbols"

* tag 'platform-drivers-x86-v4.11-2' of git://git.infradead.org/linux-platform-drivers-x86:
  platform/x86: asus-wmi: Remove quirk_no_rfkill
  platform/x86: asus-wmi: Detect quirk_no_rfkill from the DSDT
  platform/x86: fujitsu-laptop: remove redundant MODULE_ALIAS entries
  platform/x86: fujitsu-laptop: autodetect LCD interface on all models
  platform/x86: fujitsu-laptop: simplify acpi_bus_register_driver() error handling
  platform/x86: fujitsu-laptop: remove redundant forward declarations
  platform/x86: fujitsu-laptop: replace numeric values with constants
  platform/x86: fujitsu-laptop: rename FUNC_RFKILL to FUNC_FLAGS
  platform/x86: fujitsu-laptop: make platform-related variables match naming convention
  platform/x86: fujitsu-laptop: replace "hotkey" with "laptop" in symbol names
  platform/x86: fujitsu-laptop: clearly denote backlight-related symbols

Andreas reports kernel oops during rmmod of the br_netfilter module.
Hannes debugged the oops down to a NULL rt6info->rt6i_indev.

Problem is that br_netfilter has the nasty concept of adding a fake
rtable to skb->dst; this happens in a br_netfilter prerouting hook.

A second hook (in bridge LOCAL_IN) is supposed to remove these again
before the skb is handed up the stack.

However, on module unload hooks get unregistered which means an
skb could traverse the prerouting hook that attaches the fake_rtable,
while the 'fake rtable remove' hook gets removed from the hooklist
immediately after.

Fixes: 34666d46 ("netfilter: bridge: move br_netfilter out of the core")
Reported-by: Andreas Karis <akaris@redhat.com>
Debugged-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip6_fragment, in case skb has a fraglist, checks if the
skb is cloned.  If it is, it will move to the 'slow path' and allocates
new skbs for each fragment.

However, right before entering the slowpath loop, it updates the
nexthdr value of the last ipv6 extension header to NEXTHDR_FRAGMENT,
to account for the fragment header that will be inserted in the new
ipv6-fragment skbs.

In case original skb is cloned this munges nexthdr value of another
skb.  Avoid this by doing the nexthdr update for each of the new fragment
skbs separately.

This was observed with tcpdump on a bridge device where netfilter ipv6
reassembly is active:  tcpdump shows malformed fragment headers as
the l4 header (icmpv6, tcp, etc). is decoded as a fragment header.

Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reported-by: Andreas Karis <akaris@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.

The endpoints are specifically dereferenced in the i2400m_bootrom_init
path during probe (e.g. in i2400mu_tx_bulk_out).

Fixes: f398e424 ("i2400m/USB: probe/disconnect, dev init/shutdown
and reset backends")
Cc: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.

Fixes: cf7776dc ("[PATCH] isdn4linux: Siemens Gigaset drivers -
direct USB connection")
Cc: stable <stable@vger.kernel.org>	# 2.6.17
Cc: Hansjoerg Lipp <hjlipp@web.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 27596472 ("ipv6: fix ECMP route replacement") introduced a
loop that removes all siblings of an ECMP route that is being
replaced. However, this loop doesn't stop when it has replaced
siblings, and keeps removing other routes with a higher metric.
We also end up triggering the WARN_ON after the loop, because after
this nsiblings < 0.

Instead, stop the loop when we have taken care of all routes with the
same metric as the route being replaced.

  Reproducer:
  ===========
    #!/bin/sh

    ip netns add ns1
    ip netns add ns2
    ip -net ns1 link set lo up

    for x in 0 1 2 ; do
        ip link add veth$x netns ns2 type veth peer name eth$x netns ns1
        ip -net ns1 link set eth$x up
        ip -net ns2 link set veth$x up
    done

    ip -net ns1 -6 r a 2000::/64 nexthop via fe80::0 dev eth0 \
            nexthop via fe80::1 dev eth1 nexthop via fe80::2 dev eth2
    ip -net ns1 -6 r a 2000::/64 via fe80::42 dev eth0 metric 256
    ip -net ns1 -6 r a 2000::/64 via fe80::43 dev eth0 metric 2048

    echo "before replace, 3 routes"
    ip -net ns1 -6 r | grep -v '^fe80\|^ff00'
    echo

    ip -net ns1 -6 r c 2000::/64 nexthop via fe80::4 dev eth0 \
            nexthop via fe80::5 dev eth1 nexthop via fe80::6 dev eth2

    echo "after replace, only 2 routes, metric 2048 is gone"
    ip -net ns1 -6 r | grep -v '^fe80\|^ff00'

Fixes: 27596472 ("ipv6: fix ECMP route replacement")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

gup_p4d_range() should call gup_pud_range(), not itself.

[ This was not noticed on x86: this is the HAVE_GENERIC_RCU_GUP code
  used by arm[64] and powerpc    - Linus ]

Fixes: c2febafc ("mm: convert generic code to 5-level paging")
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reported-by: Anton Blanchard <anton@samba.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Improve bpf_{prog,jit_binary}_{un,}lock_ro() by throwing a
one-time warning in case of an error when the image couldn't
be set read-only, and also mark struct bpf_prog as locked when
bpf_prog_lock_ro() was called.

Reason for the latter is that bpf_prog_unlock_ro() is called from
various places including error paths, and we shouldn't mess with
page attributes when really not needed.

For bpf_jit_binary_unlock_ro() this is not needed as jited flag
implicitly indicates this, thus for archs with ARCH_HAS_SET_MEMORY
we're guaranteed to have a previously locked image. Overall, this
should also help us to identify any further potential issues with
set_memory_*() helpers.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recent merge of 'linux-kselftest-4.11-rc1' tree broke bpf test build.
None of the tests were building and test_verifier.c had tons of compiler errors.
Fix it and add #ifdef CAP_IS_SUPPORTED to support old versions of libcap.
Tested on centos 6.8 and 7
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Multipath routes can be rendered usesless when a device in one of the
paths is deleted. For example:

$ ip -f mpls ro ls
100
	nexthop as to 200 via inet 172.16.2.2  dev virt12
	nexthop as to 300 via inet 172.16.3.2  dev br0
101
	nexthop as to 201 via inet6 2000:2::2  dev virt12
	nexthop as to 301 via inet6 2000:3::2  dev br0

$ ip li del br0

When br0 is deleted the other hop is not considered in
mpls_select_multipath because of the alive check -- rt_nhn_alive
is 0.

rt_nhn_alive is decremented once in mpls_ifdown when the device is taken
down (NETDEV_DOWN) and again when it is deleted (NETDEV_UNREGISTER). For
a 2 hop route, deleting one device drops the alive count to 0. Since
devices are taken down before unregistering, the decrement on
NETDEV_UNREGISTER is redundant.

Fixes: c89359a4 ("mpls: support for dead routes")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In some cases during XenBus disconnect event handling and subsequent
queue resource release there may be some TX handlers active on
other processors. Use RCU in order to synchronize with them.
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the mpls_router module is unloaded, mpls routes are deleted but
notifications are not sent to userspace leaving userspace caches
out of sync. Add the call to mpls_notify_route in mpls_net_exit as
routes are freed.

Fixes: 0189197f ("mpls: Basic routing support")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcf_connmark_init does not check in its configuration if TCA_CONNMARK_PARMS
is set, resulting in a null pointer dereference when trying to access it.

[501099.043007] BUG: unable to handle kernel NULL pointer dereference at 0000000000000004
[501099.043039] IP: [<ffffffffc10c60fb>] tcf_connmark_init+0x8b/0x180 [act_connmark]
...
[501099.044334] Call Trace:
[501099.044345]  [<ffffffffa47270e8>] ? tcf_action_init_1+0x198/0x1b0
[501099.044363]  [<ffffffffa47271b0>] ? tcf_action_init+0xb0/0x120
[501099.044380]  [<ffffffffa47250a4>] ? tcf_exts_validate+0xc4/0x110
[501099.044398]  [<ffffffffc0f5fa97>] ? u32_set_parms+0xa7/0x270 [cls_u32]
[501099.044417]  [<ffffffffc0f60bf0>] ? u32_change+0x680/0x87b [cls_u32]
[501099.044436]  [<ffffffffa4725d1d>] ? tc_ctl_tfilter+0x4dd/0x8a0
[501099.044454]  [<ffffffffa44a23a1>] ? security_capable+0x41/0x60
[501099.044471]  [<ffffffffa470ca01>] ? rtnetlink_rcv_msg+0xe1/0x220
[501099.044490]  [<ffffffffa470c920>] ? rtnl_newlink+0x870/0x870
[501099.044507]  [<ffffffffa472cc61>] ? netlink_rcv_skb+0xa1/0xc0
[501099.044524]  [<ffffffffa47073f4>] ? rtnetlink_rcv+0x24/0x30
[501099.044541]  [<ffffffffa472c634>] ? netlink_unicast+0x184/0x230
[501099.044558]  [<ffffffffa472c9d8>] ? netlink_sendmsg+0x2f8/0x3b0
[501099.044576]  [<ffffffffa46d8880>] ? sock_sendmsg+0x30/0x40
[501099.044592]  [<ffffffffa46d8e03>] ? SYSC_sendto+0xd3/0x150
[501099.044608]  [<ffffffffa425fda1>] ? __do_page_fault+0x2d1/0x510
[501099.044626]  [<ffffffffa47fbd7b>] ? system_call_fast_compare_end+0xc/0x9b

Fixes: 22a5dc0e ("net: sched: Introduce connmark action")
Signed-off-by: Étienne Noss <etienne.noss@wifirst.fr>
Signed-off-by: Victorien Molle <victorien.molle@wifirst.fr>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It wasn't clear if the 'forwarding' setting needs to be enabled on the
interface that packets are received from, or on the interface that
packets are forwarded to, or both.

In fact (according to my code reading) the setting is relevant on the
interface that packets are received from, so this change updates the doc
to say that.
Signed-off-by: Neil Jerram <neil@tigera.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the send indirection table from the inner device (netvsc)
to the network device context.

It is possible that netvsc_device is not present (remove in progress).
This solves potential use after free issues when packet is being
created during MTU change, shutdown, or queue count changes.

Fixes: d8e18ee0 ("netvsc: enhance transmit select_queue")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>