- 21 Nov, 2012 9 commits
-
-
Sven Eckelmann authored
All packet headers in front of an ethernet header have to be completely divisible by 2 but not by 4 to make the payload after the ethernet header again 4 bytes boundary aligned. A packing of 2 is necessary to avoid extra padding at the end of the struct caused by a structure member which is larger than two bytes. Otherwise the structure would not fulfill the previously mentioned rule to avoid the misalignment of the payload after the ethernet header. It may also lead to leakage of information when the padding it not initialized before sending. Signed-off-by:
Sven Eckelmann <sven@narfation.org> Signed-off-by:
Marek Lindner <lindner_marek@yahoo.de> Signed-off-by:
Antonio Quartulli <ordex@autistici.org>
-
Sven Eckelmann authored
Signed-off-by:
-
Simon Wunderlich authored
If the skb is fragmented, the checksum must be computed on the individual fragments, just using skb->data may fail on fragmented data. Instead of doing linearizing the packet, use the new batadv_crc32 to do that more efficiently- it should not hurt replacing the old crc16 by the new crc32. Reported-by:
Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by:
-
Sven Eckelmann authored
Signed-off-by:
-
Marek Lindner authored
Signed-off-by:
-
Martin Hundebøll authored
By adding batadv_send_skb_to_orig() in send.c, we can remove duplicate code that looks up the next hop and then calls batadv_send_skb_packet(). Furthermore, this prepares the upcoming new implementation of fragmentation, which requires the next hop to route packets. Please note that this doesn't entirely remove the next-hop lookup in routing.c and unicast.c, since it is used by the current fragmentation code. Also note that the next-hop info is removed from debug messages in translation-table.c, since it is looked up elsewhere. Signed-off-by:
Martin Hundebøll <martin@hundeboll.net> Signed-off-by:
-
Antonio Quartulli authored
This patch adds support for an array of debugfs general (not soft_iface specific) attributes. With this change it will be possible to add more general attributes by simply appending them to the array without touching the rest of the code. Reported-by:
-
Simon Wunderlich authored
The address and the VLAN VID may not be packed in the respective structs. Fix this by comparing the elements individually. Reported-by:
-
Sven Eckelmann authored
The transtable_global debug file can show multiple entries for a single client when multiple gateways exist. The chosen gateway isn't marked in the list and therefore the user cannot easily debug the situation when there is a problem with the currently used gateway. The best gateway is now marked with "*" and secondary gateways are marked with "+". Signed-off-by:
-
- 20 Nov, 2012 11 commits
-
-
Neil Horman authored
In the event that an association exceeds its max_retrans attempts, we should send an ABORT chunk indicating that we are closing the assocation as a result. Because of the nature of the error, its unlikely to be received, but its a nice clean way to close the association if it does make it through, and it will give anyone watching via tcpdump a clue as to what happened. Change notes: v2) * Removed erroneous changes from sctp_make_violation_parmlen Signed-off-by:
Neil Horman <nhorman@tuxdriver.com> CC: Vlad Yasevich <vyasevich@gmail.com> CC: "David S. Miller" <davem@davemloft.net> CC: linux-sctp@vger.kernel.org Acked-by:
Vlad Yasevich <vyasevich@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Sachin Kamat authored
kfree on a null pointer is a no-op. Signed-off-by:
Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by:
-
Sachin Kamat authored
kfree on a null pointer is a no-op. Signed-off-by:
Sjur Brændeland <sjur.brandeland@stericsson.com> Signed-off-by:
-
Sachin Kamat authored
bnx2x_hsi.h was included twice. Signed-off-by:
-
Nicolas Dichtel authored
This patch add the support of 6RD tunnels management via netlink. Note that netdev_state_change() is now called when 6RD parameters are updated. 6RD parameters are updated only if there is at least one 6RD attribute. Signed-off-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by:
-
David Stevens authored
This patch provides extensions to VXLAN for supporting Distributed Overlay Virtual Ethernet (DOVE) networks. The patch includes: + a dove flag per VXLAN device to enable DOVE extensions + ARP reduction, whereby a bridge-connected VXLAN tunnel endpoint answers ARP requests from the local bridge on behalf of remote DOVE clients + route short-circuiting (aka L3 switching). Known destination IP addresses use the corresponding destination MAC address for switching rather than going to a (possibly remote) router first. + netlink notification messages for forwarding table and L3 switching misses Changes since v2 - combined bools into "u32 flags" - replaced loop with !is_zero_ether_addr() Signed-off-by:
David L Stevens <dlstevens@us.ibm.com> Signed-off-by:
-
Ben Hutchings authored
Various drivers depend on INET because they used to select INET_LRO, but they have all been converted to use GRO which has no such dependency. Signed-off-by:
Ben Hutchings <bhutchings@solarflare.com> Signed-off-by:
-
Ben Hutchings authored
Commit 2cb1deb5 ('ehea: Remove LRO support') left behind the Kconfig depends/select and feature flag. Signed-off-by:
-
Ben Hutchings authored
Commit fa37a958 ('mlx4_en: Moving to work with GRO') left behind the Kconfig depends/select, some dead code and comments referring to LRO. Signed-off-by:
Amir Vadai <amirv@mellanox.com> Signed-off-by:
-
Johannes Berg authored
The wireless and wext includes in net-sysfs.c aren't needed, so remove them. Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Joachim Eastwood authored
If ndo_validate_addr is set to the generic eth_validate_addr function there is no point in calling is_valid_ether_addr from driver ndo_open if ndo_open is not used elsewhere in the driver. With this change is_valid_ether_addr will be called from the generic eth_validate_addr function. So there should be no change in the actual behavior. Signed-off-by:
Joachim Eastwood <manabian@gmail.com> Signed-off-by:
-
- 19 Nov, 2012 20 commits
-
-
Shan Wei authored
Signed-off-by:
Shan Wei <davidshan@tencent.com> Reviewed-by:
Christoph Lameter <cl@linux.com> Signed-off-by:
-
Shan Wei authored
flush_tasklet is a struct, not a pointer in percpu var. so use this_cpu_ptr to get the member pointer. Signed-off-by:
-
Sachin Kamat authored
linux/vhost.h was included twice. Signed-off-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
-
Nicolas Ferre authored
Move to circular buffers management macro and correct an error with circular buffer initial condition. Without this patch, the macb_tx_ring_avail() function was not reporting the proper ring availability at startup: macb macb: eth0: BUG! Tx Ring full when queue awake! macb macb: eth0: tx_head = 0, tx_tail = 0 And hanginig forever... I remove the macb_tx_ring_avail() function and use the proven macros from circ_buf.h. CIRC_CNT() is used in the "consumer" part of the driver: macb_tx_interrupt() to match advice from Documentation/circular-buffers.txt. Reported-by:
Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Tested-by:
-
Eric W. Biederman authored
In (464dc801 net: Don't export sysctls to unprivileged users) I typoed and introduced a spurious backslash. Delete it. Signed-off-by:
"Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
-
Stefan Raspl authored
Remove BUG_ONs or convert to WARN_ON_ONCE/WARN_ONs since a failure within a networking device driver is no reason to shut down the entire machine. Signed-off-by:
Stefan Raspl <raspl@linux.vnet.ibm.com> Signed-off-by:
Frank Blaschka <frank.blaschka@de.ibm.com> Reviewed-by:
Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by:
-
Stefan Raspl authored
Trace all supported and enabled card features to s390dbf. Signed-off-by:
-
Stefan Raspl authored
So far, virtual NICs whether attached to a VSWITCH or a guest LAN were always displayed as guest LANs in the device driver attributes and messages, while in fact it is a virtual NIC. Signed-off-by:
-
Ursula Braun authored
Remove BUG_ON's in claw driver, since the checked error conditions are null pointer accesses. Signed-off-by:
-
Ursula Braun authored
Remove BUG_ON's in ctcm driver, since the checked error conditions are null pointer accesses. Signed-off-by:
-
Stefan Raspl authored
Eliminate a variable that is never modified. Signed-off-by:
-
Eric W. Biederman authored
Allow an unpriviled user who has created a user namespace, and then created a network namespace to effectively use the new network namespace, by reducing capable(CAP_NET_ADMIN) calls to ns_capable(net->user_ns,CAP_NET_ADMIN) calls. Allow setting of the tun iff flags. Allow creating of tun devices. Allow adding a new queue to a tun device. Signed-off-by:
Serge Hallyn <serge.hallyn@canonical.com> Signed-off-by:
-
Eric W. Biederman authored
Allow privileged users in any user namespace to bind to privileged sockets in network namespaces they control. Signed-off-by:
-
Eric W. Biederman authored
- Only allow moving network devices to network namespaces you have CAP_NET_ADMIN privileges over. - Enable creating/deleting/modifying interfaces - Enable adding/deleting addresses - Enable adding/setting/deleting neighbour entries - Enable adding/removing routes - Enable adding/removing fib rules - Enable setting the forwarding state - Enable adding/removing ipv6 address labels - Enable setting bridge parameter Signed-off-by:
-
Eric W. Biederman authored
- Enable the per device ipv4 sysctls: net/ipv4/conf/<if>/forwarding net/ipv4/conf/<if>/mc_forwarding net/ipv4/conf/<if>/accept_redirects net/ipv4/conf/<if>/secure_redirects net/ipv4/conf/<if>/shared_media net/ipv4/conf/<if>/rp_filter net/ipv4/conf/<if>/send_redirects net/ipv4/conf/<if>/accept_source_route net/ipv4/conf/<if>/accept_local net/ipv4/conf/<if>/src_valid_mark net/ipv4/conf/<if>/proxy_arp net/ipv4/conf/<if>/medium_id net/ipv4/conf/<if>/bootp_relay net/ipv4/conf/<if>/log_martians net/ipv4/conf/<if>/tag net/ipv4/conf/<if>/arp_filter net/ipv4/conf/<if>/arp_announce net/ipv4/conf/<if>/arp_ignore net/ipv4/conf/<if>/arp_accept net/ipv4/conf/<if>/arp_notify net/ipv4/conf/<if>/proxy_arp_pvlan net/ipv4/conf/<if>/disable_xfrm net/ipv4/conf/<if>/disable_policy net/ipv4/conf/<if>/force_igmp_version net/ipv4/conf/<if>/promote_secondaries net/ipv4/conf/<if>/route_localnet - Enable the global ipv4 sysctl: net/ipv4/ip_forward - Enable the per device ipv6 sysctls: net/ipv6/conf/<if>/forwarding net/ipv6/conf/<if>/hop_limit net/ipv6/conf/<if>/mtu net/ipv6/conf/<if>/accept_ra net/ipv6/conf/<if>/accept_redirects net/ipv6/conf/<if>/autoconf net/ipv6/conf/<if>/dad_transmits net/ipv6/conf/<if>/router_solicitations net/ipv6/conf/<if>/router_solicitation_interval net/ipv6/conf/<if>/router_solicitation_delay net/ipv6/conf/<if>/force_mld_version net/ipv6/conf/<if>/use_tempaddr net/ipv6/conf/<if>/temp_valid_lft net/ipv6/conf/<if>/temp_prefered_lft net/ipv6/conf/<if>/regen_max_retry net/ipv6/conf/<if>/max_desync_factor net/ipv6/conf/<if>/max_addresses net/ipv6/conf/<if>/accept_ra_defrtr net/ipv6/conf/<if>/accept_ra_pinfo net/ipv6/conf/<if>/accept_ra_rtr_pref net/ipv6/conf/<if>/router_probe_interval net/ipv6/conf/<if>/accept_ra_rt_info_max_plen net/ipv6/conf/<if>/proxy_ndp net/ipv6/conf/<if>/accept_source_route net/ipv6/conf/<if>/optimistic_dad net/ipv6/conf/<if>/mc_forwarding net/ipv6/conf/<if>/disable_ipv6 net/ipv6/conf/<if>/accept_dad net/ipv6/conf/<if>/force_tllao - Enable the global ipv6 sysctls: net/ipv6/bindv6only net/ipv6/icmp/ratelimit Signed-off-by:
-
Eric W. Biederman authored
Allow an unpriviled user who has created a user namespace, and then created a network namespace to effectively use the new network namespace, by reducing capable(CAP_NET_ADMIN) and capable(CAP_NET_RAW) calls to be ns_capable(net->user_ns, CAP_NET_ADMIN), or capable(net->user_ns, CAP_NET_RAW) calls. Allow the vlan ioctls: SET_VLAN_INGRESS_PRIORITY_CMD SET_VLAN_EGRESS_PRIORITY_CMD SET_VLAN_FLAG_CMD SET_VLAN_NAME_TYPE_CMD ADD_VLAN_CMD DEL_VLAN_CMD Signed-off-by:
-
Eric W. Biederman authored
Allow an unpriviled user who has created a user namespace, and then created a network namespace to effectively use the new network namespace, by reducing capable(CAP_NET_ADMIN) and capable(CAP_NET_RAW) calls to be ns_capable(net->user_ns, CAP_NET_ADMIN), or capable(net->user_ns, CAP_NET_RAW) calls. Allow setting bridge paramters via sysfs. Allow all of the bridge ioctls: BRCTL_ADD_IF BRCTL_DEL_IF BRCTL_SET_BRDIGE_FORWARD_DELAY BRCTL_SET_BRIDGE_HELLO_TIME BRCTL_SET_BRIDGE_MAX_AGE BRCTL_SET_BRIDGE_AGING_TIME BRCTL_SET_BRIDGE_STP_STATE BRCTL_SET_BRIDGE_PRIORITY BRCTL_SET_PORT_PRIORITY BRCTL_SET_PATH_COST BRCTL_ADD_BRIDGE BRCTL_DEL_BRDIGE Signed-off-by:
-
Eric W. Biederman authored
Allow an unpriviled user who has created a user namespace, and then created a network namespace to effectively use the new network namespace, by reducing capable(CAP_NET_ADMIN) and capable(CAP_NET_RAW) calls to be ns_capable(net->user_ns, CAP_NET_ADMIN), or capable(net->user_ns, CAP_NET_RAW) calls. Allow creation of af_key sockets. Allow creation of llc sockets. Allow creation of af_packet sockets. Allow sending xfrm netlink control messages. Allow binding to netlink multicast groups. Allow sending to netlink multicast groups. Allow adding and dropping netlink multicast groups. Allow sending to all netlink multicast groups and port ids. Allow reading the netfilter SO_IP_SET socket option. Allow sending netfilter netlink messages. Allow setting and getting ip_vs netfilter socket options. Signed-off-by:
-
Eric W. Biederman authored
Allow an unpriviled user who has created a user namespace, and then created a network namespace to effectively use the new network namespace, by reducing capable(CAP_NET_ADMIN) and capable(CAP_NET_RAW) calls to be ns_capable(net->user_ns, CAP_NET_ADMIN), or capable(net->user_ns, CAP_NET_RAW) calls. Settings that merely control a single network device are allowed. Either the network device is a logical network device where restrictions make no difference or the network device is hardware NIC that has been explicity moved from the initial network namespace. In general policy and network stack state changes are allowed while resource control is left unchanged. Allow the SIOCSIFADDR ioctl to add ipv6 addresses. Allow the SIOCDIFADDR ioctl to delete ipv6 addresses. Allow the SIOCADDRT ioctl to add ipv6 routes. Allow the SIOCDELRT ioctl to delete ipv6 routes. Allow creation of ipv6 raw sockets. Allow setting the IPV6_JOIN_ANYCAST socket option. Allow setting the IPV6_FL_A_RENEW parameter of the IPV6_FLOWLABEL_MGR socket option. Allow setting the IPV6_TRANSPARENT socket option. Allow setting the IPV6_HOPOPTS socket option. Allow setting the IPV6_RTHDRDSTOPTS socket option. Allow setting the IPV6_DSTOPTS socket option. Allow setting the IPV6_IPSEC_POLICY socket option. Allow setting the IPV6_XFRM_POLICY socket option. Allow sending packets with the IPV6_2292HOPOPTS control message. Allow sending packets with the IPV6_2292DSTOPTS control message. Allow sending packets with the IPV6_RTHDRDSTOPTS control message. Allow setting the multicast routing socket options on non multicast routing sockets. Allow the SIOCADDTUNNEL, SIOCCHGTUNNEL, and SIOCDELTUNNEL ioctls for setting up, changing and deleting tunnels over ipv6. Allow the SIOCADDTUNNEL, SIOCCHGTUNNEL, SIOCDELTUNNEL ioctls for setting up, changing and deleting ipv6 over ipv4 tunnels. Allow the SIOCADDPRL, SIOCDELPRL, SIOCCHGPRL ioctls for adding, deleting, and changing the potential router list for ISATAP tunnels. Signed-off-by:
-
Eric W. Biederman authored
Allow an unpriviled user who has created a user namespace, and then created a network namespace to effectively use the new network namespace, by reducing capable(CAP_NET_ADMIN) and capable(CAP_NET_RAW) calls to be ns_capable(net->user_ns, CAP_NET_ADMIN), or capable(net->user_ns, CAP_NET_RAW) calls. Settings that merely control a single network device are allowed. Either the network device is a logical network device where restrictions make no difference or the network device is hardware NIC that has been explicity moved from the initial network namespace. In general policy and network stack state changes are allowed while resource control is left unchanged. Allow creating raw sockets. Allow the SIOCSARP ioctl to control the arp cache. Allow the SIOCSIFFLAG ioctl to allow setting network device flags. Allow the SIOCSIFADDR ioctl to allow setting a netdevice ipv4 address. Allow the SIOCSIFBRDADDR ioctl to allow setting a netdevice ipv4 broadcast address. Allow the SIOCSIFDSTADDR ioctl to allow setting a netdevice ipv4 destination address. Allow the SIOCSIFNETMASK ioctl to allow setting a netdevice ipv4 netmask. Allow the SIOCADDRT and SIOCDELRT ioctls to allow adding and deleting ipv4 routes. Allow the SIOCADDTUNNEL, SIOCCHGTUNNEL and SIOCDELTUNNEL ioctls for adding, changing and deleting gre tunnels. Allow the SIOCADDTUNNEL, SIOCCHGTUNNEL and SIOCDELTUNNEL ioctls for adding, changing and deleting ipip tunnels. Allow the SIOCADDTUNNEL, SIOCCHGTUNNEL and SIOCDELTUNNEL ioctls for adding, changing and deleting ipsec virtual tunnel interfaces. Allow setting the MRT_INIT, MRT_DONE, MRT_ADD_VIF, MRT_DEL_VIF, MRT_ADD_MFC, MRT_DEL_MFC, MRT_ASSERT, MRT_PIM, MRT_TABLE socket options on multicast routing sockets. Allow setting and receiving IPOPT_CIPSO, IP_OPT_SEC, IP_OPT_SID and arbitrary ip options. Allow setting IP_SEC_POLICY/IP_XFRM_POLICY ipv4 socket option. Allow setting the IP_TRANSPARENT ipv4 socket option. Allow setting the TCP_REPAIR socket option. Allow setting the TCP_CONGESTION socket option. Signed-off-by:
-
