Add PMP related constants, fields and ops.  Also, update
ata_class_enabled/disabled() such that PMP classes are considered.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Update AN support in preparation of PMP support.

* s/ata_id_has_AN/ata_id_has_atapi_AN/
* add AN enabled reporting during configuration
* add err_mask to AN configuration failure reporting
* update LOCKING comment for ata_scsi_media_change_notify()
* check whether ATA dev is attached to SCSI dev ata_scsi_media_change_notify()
* set ATA_FLAG_AN in ahci and sata_sil24
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Kriten Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: Jeff Garzik <jeff@garzik.org>

Clear ARRE, we don't do auto-reallocation on reads, just on writes.

Also, hardcode the size of the array using RW_RECOVERY_MPAGE_LEN,
following the style of the surrounding code.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

* SAT specifies that FORMAT UNIT should be translated into a series
  of READ and WRITE commands that zero the ATA device.  That is far too
  cumbersome to bother with.

  Since we don't actually format the device, the old behavior of
  always returning success was inaccurate.  Change FORMAT UNIT from
  returning success immediately (old behavior) to always returning
  an error (new behavior).

* Add some comments around SYNCHRONIZE CACHE

* Shuffle scsi command code around a bit, so that things are close
  to alphabetic order.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

A few pedantic apps care about missing or lame "mandatory" SCSI
commands, so

REQUEST SENSE -- as we autosense, R.S. just returns zeroes

SEND DIAGNOSTIC -- our default (no-op) self-test succeeds, all
		   other requests for testing fail.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Certain device which reports diagnostic failure also reports invalid
device signature.  Assume ATA_DEV_ATA on diagnostic failure if reset
indicates device presence.

This is fix for bugzilla bug 8784.

  http://bugzilla.kernel.org/show_bug.cgi?id=8784Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Edward Amsden <amsden_linux@earthlink.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Make ata_dev_try_classify() take a pointer to ata_device instead of
ata_port/port_number combination for consistency and add @present
argument.  @present indicates whether the device seems present during
reset.  It's the result of TF access during softreset and link
onlineness during hardreset.  @present will be used to improve
diagnostic failure handling.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Reimplement port_map handling such that

1. Non-zero PORTS_IMPL value is always examined and used if consistent
   with cap.n_ports.

2. When PI and cat.n_ports are inconsistent, honor cap.n_ports and
   force port_map to be ((1 << cap.n_ports) - 1).

3. There were two separate places dealing with port_map.  Unify them
   to one.

As all newer ahci chips seem to get PI correct and older ones usually
have zero PI.  Controllers with holes in PI are very unlikely to screw
up PI, so #2 makes more sense than following inconsistent PI.

Without this change, not setting ATA_FLAG_HONOR_PI when it's needed
results in weird detection failure.  This changed logic should be able
to handle all known cases correctly automatically.

Verified on ICH6 (reports 0 PI), ICH8 (with holes in port_map), ICH9,
JMB360 and JMB363.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This patch reimplement ata_hpa_resize() such that...

* All HPA related decisions are made inside ata_hpa_resize() proper.
  ata_hpa_resize() returns 0 if configuration can proceed, -errno if
  device needs to be reset and reconfigured.

* All errors are handled properly.  If HPA unlocking isn't requested,
  HPA handling is disabled automatically to avoid unnecessary device
  detection failure.

* Messages are trimmed.  HPA detection message is printed only during
  initial configuration.  HPA unlocked message is printed only during
  initial configuration or unlocking results in different size.

* Instead of using sectors returned in TF of SET_MAX, re-read IDENTIFY
  data as that's the value the device is going to use.

* It's called early during ata_dev_configure() as IDENTIFY data might
  change after resizing.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Merge ata_read_native_max_addres_ext() into ata_read_native_max_address()
and combine ata_set_native_max_address_ext() and
ata_set_native_max_address() into ata_set_max_sectors().

* reduce duplicate code
* return 0 or -errno depending on error conditions
* report if command fails
* use ATA_LBA instead of 0x40

This is in preparation of ata_hpa_resize() update.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Move ata_id_n_sectors() upward right below ata_id_c_string().  This is
to accomodate later changes.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

In anticipation of more features, increase number of config flags
allowed, and move the init flags.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Hugh Dickens <hugh@veritas.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This patch removes some incorrect formatting spaces and replaces them with tabs.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

  simple search-and-replace of direct scsi_cmnd access to
  use the data buffer accessors.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

     This is a minimal patch needed to remove use of !use_sg
     but it is not a complete clean up of the !use_sg paths.
     Libata-core still has the qc->flags & ATA_QCFLAG_SG
     and !qc->n_elem code paths. Perhaps an ata maintainer
     would have a go at it.

     - TODO: further cleanup of qc->flags & ATA_QCFLAG_SG
       and !qc->n_elem code paths in libata-core
     - TODO: Use scsi_dma_{map,unmap} where applicable.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Some iomap functions were still using readl/writel and friends which
happens to work on most platforms but is not correct.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Support the use of '*' in model_num and model_rev entries
in ata_device_blacklist[].

Based largely on David Milburn's "libata-core: support wildcard matching
in ata_blacklist_entry" patch.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Use a form of array init that is less fragile, less sensitive to trivial
typos and ordering mismatches.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Updated and simplified driver. Use only register transfer timing for both
data and register transfers. This gives poorer performance in PIO1 and 2,
but should not be a problem in PIO3 and 4, correct me if I'm wrong :)

The driver works very we'll but I still wonder about the interrupts. I have
an interrupt line, that works nicely when POLLING flag is not set. The
problem is the number of interrupts that eat away my CPU cycles.

When using the POLLING flag there seem to be some interrupts that dosen't get
cleared. Furthermore the device dosen't drive INTRQ high, it stays at 2.5 volts
and generates a lot of interrupts due to ripple / noise. What to do?
Signed-off-by: Kristoffer Nyborg Gregertsen <kngregertsen@norway.atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Fix all issues pointed out in Jeff's email.
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

EH is sometimes repeated without any error or action.  For example,
this happens when probing IDENTIFY fails because of a phantom device.
In these cases, all the repeated EH does is making sure there is no
unhandled error or pending action and return.  This repeation is
necessary to avoid losing any event which occurred while EH was in
progress.

Unfortunately, this dry run causes annonying "EH pending after
completion" message.  This patch moves the repeat reporting into
ata_eh_report() such that it's more compact and skipped on dry runs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mikael Pettersson <mikep@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Currently, port configuration reporting has the following problems.

* iomapped address is reported instead of raw address
* report contains irrelevant fields or lacks necessary fields for
  non-SFF controllers.
* host->irq/irq2 are there just for reporting and hacky.

This patch implements and uses ata_port_desc() and
ata_port_pbar_desc().  ata_port_desc() is almost identical to
ata_ehi_push_desc() except that it takes @ap instead of @ehi, has no
locking requirement, can only be used during host initialization and "
" is used as separator instead of ", ".  ata_port_pbar_desc() is a
helper to ease reporting of a PCI BAR or an offsetted address into it.

LLD pushes whatever description it wants using the above two
functions.  The accumulated description is printed on host
registration after "[S/P]ATA max MAX_XFERMODE ".

SFF init helpers and ata_host_activate() automatically add
descriptions for addresses and irq respectively, so only LLDs which
isn't standard SFF need to add custom descriptions.  In many cases,
such controllers need to report different things anyway.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Minor cleanup to remove the unneeded rmb()s per Jeff's advice. Also removed the
pll_clock < 0 check since pll_clock now guaranteed to be >= 0 after Mikael's patch.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The ATA specifications require checks on certain flags before assuming
the validity of other data. Go through the methods and correct those
needing extra checks. Also note limits on ata_id_major_version with
respect to ATA-1 and ATA-2. Correct the 32bit PIO check.

Wants to sit in -mm for a bit in case of a screwup on my part that I
didn't hit on the test drives and also in case someone, somewhere has
a drive that gets it wrong.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

If we have a PATA cable with a SATA drive on it then we've found a
bridge and we can flip the cable type. This fixes some cable detect
problems with SATA bridges on chipsets and misdetected cable types.

In theory cable detection and mode limiting is needed if you put a
SATA/PATA bridge on a 40 wire cable, but I see no way to deal with
that other than to point out its not a good idea anyway.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

With the PCI layer properly handling legacy IDE and the kernel now using
it these can go
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This avoids allocating DMA buffers if not needed but at the moment is
mostly just a neatness item.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

It was always set to ata_port_disable().  Removed the hook, and replaced
the very few ap->ops->port_disable() callsites with direct calls to
ata_port_disable().
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Testing this on the VIA boards fixes several problems with otherwise
undetectable SATA bridge chips
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

We can make use of this on the pata_amd driver as many Nvidia devices
don't have reliable cable detect.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Combined from two Alan Cox patches:

1) libata: ACPI checks for 80wire cable

We can use the ACPI mode information with several drivers as a hint to
cable type. If the ACPI mode set by the BIOS is faster than UDMA33 then
we know the BIOS thinks there are 80wire cables. If it doesn't set such a
mode or it has no ACPI method then we get no further information and can
rely on existing approaches

Introduce the function headers needed. Null it out for non ACPI boxes
Signed-off-by: Alan Cox <alan@redhat.com>

2) libata: ACPI checks for 80wire cable

Provide actual methods for checking if the ACPI support thinks the cable
is 80wire, or doesn't know
Signed-off-by: Alan Cox <alan@redhat.com>

Combined into a single changeset and
Signed-off-by: Jeff Garzik <jeff@garzik.org>

* ->irq_ack() is redundant to what the irq handler already
  performs... chk-status + irq-clear.  Furthermore, it is only
  called in one place, when screaming-irq-debugging is enabled,
  so we don't want to bother with a hook just for that.

* ata_dummy_irq_on() is only ever used in drivers that have
  no callpath reaching ->irq_on().  Remove .irq_on hook from
  those drivers, and the now-unused ata_dummy_irq_on()
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Tell the compiler that [__]ata_ehi_push_desc() functions take printf
style format string and arguments.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

ata_wait_idle() identified controller by printing out the address of
the Status register.  This is bogus because 1. it's iomapped address
2. some controllers don't have Status register and don't initialize
the field.  Use ata_port_printk() instead.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Remove unneeded, undesirable cast of void*.

Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sonic Zhang <sonic.adi@gmail.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

There is another outstanding issue with ata_piix.c.  Intel has never
officially supported anything faster than PATA 100MB/s.

But, the ata_piix.c driver "define" the ICH5 & ICH7 as UDMA6 (aka 133MB/s)
capable.  [ Well, no one has probably noticed it before, because there is bug
in do_pata_set_dmamode...  Just look at
libata_atapiix_enable_real_udma133.patch and you'll see what wrong with it.  ]

Here are Intel's datasheets for the affected chipsets: ICH5 Datasheet:
http://www.intel.com/design/chipsets/datashts/252516.htm (See note on page
183: "...  the ICH5 supports reads at the maximum rate of 100MB/s.")

ICH7 Datasheet: http://www.intel.com/design/chipsets/datashts/307013.htm (See
first note on page 190: "...  the ICH7 supports reads at the maximum rate of
100MB/s.")

They are two different ways to deal with it:

- Either -

1. replace all ich_pata_133 with ich_pata_100.
   (libata_atapiix_disable_udma6.diff - diff from 2.6.22 )

- Or -

2. keep all ich_pata_133 and fix the bug in "do_pata_set_dmamode".
   (libata_atapiix_enable_real_udma133.patch - diff from 2.6.22) If there are
   any concerns about the safety of the patch patch:
   http://lkml.org/lkml/2007/7/6/292 (It was already tested by an Intel
   employee, but I guess a bit more user input is necessary here...  )

This patch implements 1.

Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>