- 26 Nov, 2014 36 commits
-
-
Trond Myklebust authored
commit 869f9dfa upstream. Any attempt to call nfs_remove_bad_delegation() while a delegation is being returned is currently a no-op. This means that we can end up looping forever in nfs_end_delegation_return() if something causes the delegation to be revoked. This patch adds a mechanism whereby the state recovery code can communicate to the delegation return code that the delegation is no longer valid and that it should not be used when reclaiming state. It also changes the return value for nfs4_handle_delegation_recall_error() to ensure that nfs_end_delegation_return() does not reattempt the lock reclaim before state recovery is done. http://lkml.kernel.org/r/CAN-5tyHwG=Cn2Q9KsHWadewjpTTy_K26ee+UnSvHvG4192p-Xw@mail.gmail.comSigned-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by:
Kamal Mostafa <kamal@canonical.com>
-
Trond Myklebust authored
commit 0c116cad upstream. This patch removes the assumption made previously, that we only need to check the delegation stateid when it matches the stateid on a cached open. If we believe that we hold a delegation for this file, then we must assume that its stateid may have been revoked or expired too. If we don't test it then our state recovery process may end up caching open/lock state in a situation where it should not. We therefore rename the function nfs41_clear_delegation_stateid as nfs41_check_delegation_stateid, and change it to always run through the delegation stateid test and recovery process as outlined in RFC5661. http://lkml.kernel.org/r/CAN-5tyHwG=Cn2Q9KsHWadewjpTTy_K26ee+UnSvHvG4192p-Xw@mail.gmail.comSigned-off-by:
-
Trond Myklebust authored
commit 4dfd4f7a upstream. NFSv4.0 does not have TEST_STATEID/FREE_STATEID functionality, so unlike NFSv4.1, the recovery procedure when stateids have expired or have been revoked requires us to just forget the delegation. http://lkml.kernel.org/r/CAN-5tyHwG=Cn2Q9KsHWadewjpTTy_K26ee+UnSvHvG4192p-Xw@mail.gmail.comSigned-off-by:
-
Jan Kara authored
commit 16caf5b6 upstream. Variable 'err' needn't be initialized when nfs_getattr() uses it to check whether it should call generic_fillattr() or not. That can result in spurious error returns. Initialize 'err' properly. Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
-
Peng Tao authored
commit 8c393f9a upstream. For pNFS direct writes, layout driver may dynamically allocate ds_cinfo.buckets. So we need to take care to free them when freeing dreq. Ideally this needs to be done inside layout driver where ds_cinfo.buckets are allocated. But buckets are attached to dreq and reused across LD IO iterations. So I feel it's OK to free them in the generic layer. Signed-off-by:
Peng Tao <tao.peng@primarydata.com> Signed-off-by:
-
Miklos Szeredi authored
commit 799b6014 upstream. Audit rules disappear when an inode they watch is evicted from the cache. This is likely not what we want. The guilty commit is "fsnotify: allow marks to not pin inodes in core", which didn't take into account that audit_tree adds watches with a zero mask. Adding any mask should fix this. Fixes: 90b1e7a5 ("fsnotify: allow marks to not pin inodes in core") Signed-off-by:
Miklos Szeredi <mszeredi@suse.cz> Signed-off-by:
Paul Moore <pmoore@redhat.com> Signed-off-by:
-
Takashi Iwai authored
commit 1a290581 upstream. M-audio FastTrack Ultra quirk doesn't release the kzalloc'ed memory. This patch adds the private_free callback to release it properly. Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Helge Deller authored
commit 2fe749f5 upstream. Switch over the msgctl, shmat, shmctl and semtimedop syscalls to use the compat layer. The problem was found with the debian procenv package, which called shmctl(0, SHM_INFO, &info); in which the shmctl syscall then overwrote parts of the surrounding areas on the stack on which the info variable was stored and thus lead to a segfault later on. Additionally fix the definition of struct shminfo64 to use unsigned longs like the other architectures. This has no impact on userspace since we only have a 32bit userspace up to now. Signed-off-by:
Helge Deller <deller@gmx.de> Cc: John David Anglin <dave.anglin@bell.net> Signed-off-by:
-
Joe Thornber authored
commit 9b460d36 upstream. The walk code was using a 'ro_spine' to hold it's locked btree nodes. But this data structure is designed for the rolling lock scheme, and as such automatically unlocks blocks that are two steps up the call chain. This is not suitable for the simple recursive walk algorithm, which retraces its steps. This code is only used by the persistent array code, which in turn is only used by dm-cache. In order to trigger it you need to have a mapping tree that is more than 2 levels deep; which equates to 8-16 million cache blocks. For instance a 4T ssd with a very small block size of 32k only just triggers this bug. The fix just places the locked blocks on the stack, and stops using the ro_spine altogether. Signed-off-by:
Joe Thornber <ejt@redhat.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Christoph Hellwig authored
commit 48379270 upstream. Setups that use the blk-mq I/O path can lock up if a host with a single device that has its door locked enters EH. Make sure to only send the command to re-lock the door to devices that actually were reset and thus might have lost their state. Otherwise the EH code might be get blocked on blk_get_request as all requests for non-reset devices might be in use. Signed-off-by:
Christoph Hellwig <hch@lst.de> Reported-by:
Meelis Roos <meelis.roos@ut.ee> Tested-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Pali Rohár authored
commit 9d720b34 upstream. On some Dell Latitude laptops ALPS device or Dell EC send one invalid byte in 6 bytes ALPS packet. In this case psmouse driver enter out of sync state. It looks like that all other bytes in packets are valid and also device working properly. So there is no need to do full device reset, just need to wait for byte which match condition for first byte (start of packet). Because ALPS packets are bigger (6 or 8 bytes) default limit is small. This patch increase number of invalid bytes to size of 2 ALPS packets which psmouse driver can drop before do full reset. Resetting ALPS devices take some time and when doing reset on some Dell laptops touchpad, trackstick and also keyboard do not respond. So it is better to do it only if really necessary. Signed-off-by:
Pali Rohár <pali.rohar@gmail.com> Tested-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Pali Rohár authored
commit 4ab8f7f3 upstream. 5th and 6th byte of ALPS trackstick V3 protocol match condition for first byte of PS/2 3 bytes packet. When driver enters out of sync state and ALPS trackstick is sending data then driver match 5th, 6th and next 1st bytes as PS/2. It basically means if user is using trackstick when driver is in out of sync state driver will never resync. Processing these bytes as 3 bytes PS/2 data cause total mess (random cursor movements, random clicks) and make trackstick unusable until psmouse driver decide to do full device reset. Lot of users reported problems with ALPS devices on Dell Latitude E6440, E6540 and E7440 laptops. ALPS device or Dell EC for unknown reason send some invalid ALPS PS/2 bytes which cause driver out of sync. It looks like that i8042 and psmouse/alps driver always receive group of 6 bytes packets so there are no missing bytes and no bytes were inserted between valid ones. This patch does not fix root of problem with ALPS devices found in Dell Latitude laptops but it does not allow to process some (invalid) subsequence of 6 bytes ALPS packets as 3 bytes PS/2 when driver is out of sync. So with this patch trackstick input device does not report bogus data when also driver is out of sync, so trackstick should be usable on those machines. Signed-off-by:
-
Devin Ryles authored
commit b4565913 upstream. This patch adds DeviceIDs for Sunrise Point-LP Signed-off-by:
Devin Ryles <devin.ryles@intel.com> Signed-off-by:
-
James Ralston authored
commit c8b00fd2 upstream. This patch adds the HD Audio Device IDs for the Intel Sunrise Point PCH. [the item position rearranged by tiwai] Signed-off-by:
James Ralston <james.d.ralston@intel.com> Signed-off-by:
-
Alex Deucher authored
commit f0d7bfb9 upstream. Need to unlock the crtc after updating the blanking state. Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Alex Deucher authored
commit 0b021c58 upstream. Use gart rather than vram to avoid having to deal with the HDP cache. Port of adfed2b0 (drm/radeon: use gart memory for DMA ring tests) to the IB tests. Signed-off-by:
-
Alex Deucher authored
commit 8efe82ca upstream. The power management code calls into the display code for certain things. If certain power management sysfs attributes are called before the driver has finished initializing all of the hardware we can run into problems with uninitialized modesetting state. Add a check to make sure modesetting init has completed to the bandwidth update callbacks to fix this. Can be triggered by the tlp and laptop start up scripts depending on the timing. bugs: https://bugzilla.kernel.org/show_bug.cgi?id=83611 https://bugs.freedesktop.org/show_bug.cgi?id=85771Signed-off-by:
-
Jammy Zhou authored
commit dc4edad6 upstream. CE ram size is 32k/0k/0k for GFX/CS0/CS1 with CIK Ported from amdgpu driver. Signed-off-by:
Jammy Zhou <Jammy.Zhou@amd.com> Signed-off-by:
-
Greg Kurz authored
commit 24c65bc7 upstream. The add_early_randomness() function in drivers/char/hw_random/core.c passes a 16-byte buffer to pseries_rng_data_read(). Unfortunately, plpar_hcall() returns four 64-bit values and trashes 16 bytes on the stack. This bug has been lying around for a long time. It got unveiled by: commit d3cc7996 Author: Amit Shah <amit.shah@redhat.com> Date: Thu Jul 10 15:42:34 2014 +0530 hwrng: fetch randomness only after device init It may trig a oops while loading or unloading the pseries-rng module for both PowerVM and PowerKVM guests. This patch does two things: - pass an intermediate well sized buffer to plpar_hcall(). This is acceptalbe since we're not on a hot path. - move to the new read API so that we know the return buffer size for sure. Signed-off-by:
Greg Kurz <gkurz@linux.vnet.ibm.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Cristian Stoica authored
commit 738459e3 upstream. If dma mapping for dma_addr_out fails, the descriptor memory is freed but the previous dma mapping for dma_addr_in remains. This patch resolves the missing dma unmap and groups resource allocations at function start. Signed-off-by:
Cristian Stoica <cristian.stoica@freescale.com> Signed-off-by:
-
Nadav Amit authored
commit d29b9d7e upstream. The emulator could reuse an op->type from a previous instruction for some immediate values. If it mistakenly considers the operands as memory operands, it will performs a memory read and overwrite op->val. Consider for instance the ROR instruction - src2 (the number of times) would be read from memory instead of being used as immediate. Mark every immediate operand as such to avoid this problem. Fixes: c44b4c6aSigned-off-by:
Nadav Amit <namit@cs.technion.ac.il> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Joe Thornber authored
commit c822ed96 upstream. Avoids normal IO racing with discard. Signed-off-by:
-
Herbert Xu authored
commit 3ce9b20f upstream. When VLAN is in use in macvtap_put_user, we end up setting csum_start to the wrong place. The result is that the whoever ends up doing the checksum setting will corrupt the packet instead of writing the checksum to the expected location, usually this means writing the checksum with an offset of -4. This patch fixes this by adjusting csum_start when VLAN tags are detected. Fixes: f09e2249 ("macvtap: restore vlan header on user read") Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Herbert Xu authored
commit a8f9bfdf upstream. When VLAN acceleration is in use on the xmit path, we end up setting csum_start to the wrong place. The result is that the whoever ends up doing the checksum setting will corrupt the packet instead of writing the checksum to the expected location, usually this means writing the checksum with an offset of -4. This patch fixes this by adjusting csum_start when VLAN acceleration is detected. Fixes: 6680ec68 ("tuntap: hardware vlan tx support") Signed-off-by:
-
Johannes Berg authored
commit b8fff407 upstream. Upon receiving the last fragment, all but the first fragment are freed, but the multicast check for statistics at the end of the function refers to the current skb (the last fragment) causing a use-after-free bug. Since multicast frames cannot be fragmented and we check for this early in the function, just modify that check to also do the accounting to fix the issue. Reported-by:
Yosef Khyal <yosefx.khyal@intel.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Johannes Berg authored
commit 46238845 upstream. When an interface is deleted, an ongoing hardware scan is canceled and the driver must abort the scan, at the very least reporting completion while the interface is removed. However, if it scheduled the work that might only run after everything is said and done, which leads to cfg80211 warning that the scan isn't reported as finished yet; this is no fault of the driver, it already did, but mac80211 hasn't processed it. To fix this situation, flush the delayed work when the interface being removed is the one that was executing the scan. Reported-by:
Sujith Manoharan <sujith@msujith.org> Tested-by:
-
Luciano Coelho authored
commit ff1e417c upstream. Due to the time it takes to process the beacon that started the CSA process, we may be late for the switch if we try to reach exactly beacon 0. To avoid that, use count - 1 when calculating the switch time. Reported-by:
Jouni Malinen <j@w1.fi> Signed-off-by:
Luciano Coelho <luciano.coelho@intel.com> Signed-off-by:
-
Luciano Coelho authored
commit 84469a45 upstream. If we are switching from an HT40+ to an HT40- channel (or vice-versa), we need the secondary channel offset IE to specify what is the post-CSA offset to be used. This applies both to beacons and to probe responses. In ieee80211_parse_ch_switch_ie() we were ignoring this IE from beacons and using the *current* HT information IE instead. This was causing us to use the same offset as before the switch. Fix that by using the secondary channel offset IE also for beacons and don't ever use the pre-switch offset. Additionally, remove the "beacon" argument from ieee80211_parse_ch_switch_ie(), since it's not needed anymore. Reported-by:
-
Krzysztof Kozlowski authored
commit cdaf3e15 upstream. The charger manager obtained in probe references to power supplies for all chargers with power_supply_get_by_name() for later usage. However if such charger driver was removed then this reference would point to old power supply (from driver which was removed). This lead to accessing invalid memory which could be observed with: $ echo "max77693-charger" > /sys/bus/platform/drivers/max77693-charger/unbind $ grep . /sys/devices/virtual/power_supply/battery/charger.0/* $ grep . /sys/devices/virtual/power_supply/battery/* [ 15.339817] Unable to handle kernel paging request at virtual address 0001c12c [ 15.346187] pgd = edd08000 [ 15.348814] [0001c12c] *pgd=6dce2831, *pte=00000000, *ppte=00000000 [ 15.355075] Internal error: Oops: 80000007 [#1] PREEMPT SMP ARM [ 15.360967] Modules linked in: [ 15.364010] CPU: 2 PID: 1388 Comm: grep Not tainted 3.17.0-next-20141007-00027-ga95e761db1b0 #245 [ 15.372859] task: ee03ad00 ti: edcf6000 task.ti: edcf6000 [ 15.378241] PC is at 0x1c12c [ 15.381113] LR is at is_ext_pwr_online+0x30/0x6c [ 15.385706] pc : [<0001c12c>] lr : [<c0339fc4>] psr: a0000013 [ 15.385706] sp : edcf7e88 ip : 00000000 fp : 00000000 [ 15.397161] r10: eeb02c08 r9 : c04b1f84 r8 : eeb02c00 [ 15.402369] r7 : edc69a10 r6 : eea6ac10 r5 : eea6ac10 r4 : 00000004 [ 15.408878] r3 : 0001c12c r2 : edcf7e8c r1 : 00000004 r0 : ee914418 [ 15.415390] Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user [ 15.422506] Control: 10c5387d Table: 6dd0804a DAC: 00000015 [ 15.428236] Process grep (pid: 1388, stack limit = 0xedcf6240) [ 15.434050] Stack: (0xedcf7e88 to 0xedcf8000) [ 15.438395] 7e80: ee03ad00 00000000 edcf7f80 eea6aca8 edcf7ec4 c033b7b0 [ 15.446554] 7ea0: 00000001 ee1cc3f0 00000004 c06e1e44 eebdc000 c06e1e44 eeb02c00 c0337144 [ 15.454713] 7ec0: ee2dac68 c005cffc ee1cc3c0 c06e1e44 00000fff 00001000 eebdc000 c0278ca8 [ 15.462872] 7ee0: c0278c8c ee1cc3c0 eeb7ce00 c014422c edcf7f20 00008000 ee1cc3c0 ee9a48c0 [ 15.471030] 7f00: 00000001 00000001 edcf7f80 c0142d94 c0142d70 c01060f4 00021000 ee1cc3f0 [ 15.479190] 7f20: 00000000 00000000 c06a2150 eebdc000 2e7ec000 ee9a48c0 00008000 00021000 [ 15.487349] 7f40: edcf7f80 00008000 edcf6000 00021000 00021000 c00e39a4 00000000 ee9a48c0 [ 15.495508] 7f60: 00004000 00000000 00000000 ee9a48c0 ee9a48c0 00008000 00021000 c00e3aa0 [ 15.503668] 7f80: 00000000 00000000 0001f2e0 0001f2e0 00021000 00001000 00000003 c000f364 [ 15.511826] 7fa0: 00000000 c000f1a0 0001f2e0 00021000 00000003 00021000 00008000 00000000 [ 15.519986] 7fc0: 0001f2e0 00021000 00001000 00000003 00000001 000205e8 00000000 00021000 [ 15.528145] 7fe0: 00008000 bebbe910 0000a7ad b6edc49c 60000010 00000003 aaaaaaaa aaaaaaaa [ 15.536320] [<c0339fc4>] (is_ext_pwr_online) from [<c033b7b0>] (charger_get_property+0x170/0x314) [ 15.545164] [<c033b7b0>] (charger_get_property) from [<c0337144>] (power_supply_show_property+0x48/0x20c) [ 15.554719] [<c0337144>] (power_supply_show_property) from [<c0278ca8>] (dev_attr_show+0x1c/0x48) [ 15.563577] [<c0278ca8>] (dev_attr_show) from [<c014422c>] (sysfs_kf_seq_show+0x84/0x104) [ 15.571725] [<c014422c>] (sysfs_kf_seq_show) from [<c0142d94>] (kernfs_seq_show+0x24/0x28) [ 15.579973] [<c0142d94>] (kernfs_seq_show) from [<c01060f4>] (seq_read+0x1b0/0x484) [ 15.587614] [<c01060f4>] (seq_read) from [<c00e39a4>] (vfs_read+0x88/0x144) [ 15.594552] [<c00e39a4>] (vfs_read) from [<c00e3aa0>] (SyS_read+0x40/0x8c) [ 15.601417] [<c00e3aa0>] (SyS_read) from [<c000f1a0>] (ret_fast_syscall+0x0/0x48) [ 15.608877] Code: bad PC value [ 15.611991] ---[ end trace a88fcc95208db283 ]--- The charger-manager should get reference to charger power supply on each use of get_property callback. Signed-off-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com> Fixes: 3bb3dbbd ("power_supply: Add initial Charger-Manager driver") Signed-off-by:
Sebastian Reichel <sre@kernel.org> [ kamal: backport to 3.13-stable: context ] Signed-off-by:
-
James Ralston authored
commit 690000b9 upstream. This patch adds the AHCI-mode SATA Device IDs for the Intel Sunrise Point PCH. Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Tejun Heo authored
commit 66a7cbc3 upstream. Samsung pci-e SSDs on macbooks failed miserably on NCQ commands, so 67809f85 ("ahci: disable NCQ on Samsung pci-e SSDs on macbooks") disabled NCQ on them. It turns out that NCQ is fine as long as MSI is not used, so let's turn off MSI and leave NCQ on. Signed-off-by:
Imre Kaloz <kaloz@openwrt.org> Fixes: 67809f85 ("ahci: disable NCQ on Samsung pci-e SSDs on macbooks") Signed-off-by:
-
Heinz Mauelshagen authored
commit 40d43c4b upstream. The dm-raid superblock (struct dm_raid_superblock) is padded to 512 bytes and that size is being used to read it in from the metadata device into one preallocated page. Reading or writing this on a 512-byte sector device works fine but on a 4096-byte sector device this fails. Set the dm-raid superblock's size to the logical block size of the metadata device, because IO at that size is guaranteed too work. Also add a size check to avoid silent partial metadata loss in case the superblock should ever grow past the logical block size or PAGE_SIZE. [includes pointer math fix from Dan Carpenter] Reported-by:
"Liuhua Wang" <lwang@suse.com> Signed-off-by:
Heinz Mauelshagen <heinzm@redhat.com> Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Max Filippov authored
commit 2651cc69 upstream. Userspace actually passes single parameter (path name) to the umount syscall, so new umount just fails. Fix it by requesting old umount syscall implementation and re-wiring umount to it. Signed-off-by:
Max Filippov <jcmvbkbc@gmail.com> Signed-off-by:
-
Mikulas Patocka authored
commit 9d28eb12 upstream. The shrinker uses gfp flags to indicate what kind of operation can the driver wait for. If __GFP_IO flag is present, the driver can wait for block I/O operations, if __GFP_FS flag is present, the driver can wait on operations involving the filesystem. dm-bufio tested for __GFP_IO. However, dm-bufio can run on a loop block device that makes calls into the filesystem. If __GFP_IO is present and __GFP_FS isn't, dm-bufio could still block on filesystem operations if it runs on a loop block device. The change from __GFP_IO to __GFP_FS supposedly fixes one observed (though unreproducible) deadlock involving dm-bufio and loop device. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
-
Jeff Layton authored
commit 1b19453d upstream. Currently, the DRC cache pruner will stop scanning the list when it hits an entry that is RC_INPROG. It's possible however for a call to take a *very* long time. In that case, we don't want it to block other entries from being pruned if they are expired or we need to trim the cache to get back under the limit. Fix the DRC cache pruner to just ignore RC_INPROG entries. Signed-off-by:
Jeff Layton <jlayton@primarydata.com> Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Cc: Joseph Salisbury <joseph.salisbury@canonical.com> Reference: http://bugs.launchpad.net/bugs/1396065Signed-off-by:
-
Jeff Layton authored
commit a0ef5e19 upstream. Currently when we are processing a request, we try to scrape an expired or over-limit entry off the list in preference to allocating a new one from the slab. This is unnecessarily complicated. Just use the slab layer. Signed-off-by:
Jeff Layton <jlayton@redhat.com> Signed-off-by:
-
- 25 Nov, 2014 4 commits
-
-
Wolfram Sang authored
commit 11cfbfb0 upstream. iowait is for blkio [1]. I2C shouldn't use it. [1] https://lkml.org/lkml/2014/11/3/317Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Acked-by:
Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by:
-
Yijing Wang authored
commit e4a60d13 upstream. There is a race condition when removing glue directory. It can be reproduced in following test: path 1: Add first child device device_add() get_device_parent() /*find parent from glue_dirs.list*/ list_for_each_entry(k, &dev->class->p->glue_dirs.list, entry) if (k->parent == parent_kobj) { kobj = kobject_get(k); break; } .... class_dir_create_and_add() path2: Remove last child device under glue dir device_del() cleanup_device_parent() cleanup_glue_dir() kobject_put(glue_dir); If path2 has been called cleanup_glue_dir(), but not call kobject_put(glue_dir), the glue dir is still in parent's kset list. Meanwhile, path1 find the glue dir from the glue_dirs.list. Path2 may release glue dir before path1 call kobject_get(). So kernel will report the warning and bug_on. This is a "classic" problem we have of a kref in a list that can be found while the last instance could be removed at the same time. This patch reuse gdp_mutex to fix this race condition. The following calltrace is captured in kernel 3.4, but the latest kernel still has this bug. ----------------------------------------------------- <4>[ 3965.441471] WARNING: at ...include/linux/kref.h:41 kobject_get+0x33/0x40() <4>[ 3965.441474] Hardware name: Romley <4>[ 3965.441475] Modules linked in: isd_iop(O) isd_xda(O)... ... <4>[ 3965.441605] Call Trace: <4>[ 3965.441611] [<ffffffff8103717a>] warn_slowpath_common+0x7a/0xb0 <4>[ 3965.441615] [<ffffffff810371c5>] warn_slowpath_null+0x15/0x20 <4>[ 3965.441618] [<ffffffff81215963>] kobject_get+0x33/0x40 <4>[ 3965.441624] [<ffffffff812d1e45>] get_device_parent.isra.11+0x135/0x1f0 <4>[ 3965.441627] [<ffffffff812d22d4>] device_add+0xd4/0x6d0 <4>[ 3965.441631] [<ffffffff812d0dbc>] ? dev_set_name+0x3c/0x40 .... <2>[ 3965.441912] kernel BUG at ..../fs/sysfs/group.c:65! <4>[ 3965.441915] invalid opcode: 0000 [#1] SMP ... <4>[ 3965.686743] [<ffffffff811a677e>] sysfs_create_group+0xe/0x10 <4>[ 3965.686748] [<ffffffff810cfb04>] blk_trace_init_sysfs+0x14/0x20 <4>[ 3965.686753] [<ffffffff811fcabb>] blk_register_queue+0x3b/0x120 <4>[ 3965.686756] [<ffffffff812030bc>] add_disk+0x1cc/0x490 .... ------------------------------------------------------- Signed-off-by:
Yijing Wang <wangyijing@huawei.com> Signed-off-by:
Weng Meiling <wengmeiling.weng@huawei.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Dmitry Eremin-Solenikov authored
commit 2b9375b9 upstream. If PM_RUNTIME is enabled, it is easy to trigger the following backtrace on pxa2xx hosts: ------------[ cut here ]------------ WARNING: CPU: 0 PID: 1 at /home/lumag/linux/arch/arm/mach-pxa/clock.c:35 clk_disable+0xa0/0xa8() Modules linked in: CPU: 0 PID: 1 Comm: swapper Not tainted 3.17.0-00007-g1b3d2ee-dirty #104 [<c000de68>] (unwind_backtrace) from [<c000c078>] (show_stack+0x10/0x14) [<c000c078>] (show_stack) from [<c001d75c>] (warn_slowpath_common+0x6c/0x8c) [<c001d75c>] (warn_slowpath_common) from [<c001d818>] (warn_slowpath_null+0x1c/0x24) [<c001d818>] (warn_slowpath_null) from [<c0015e80>] (clk_disable+0xa0/0xa8) [<c0015e80>] (clk_disable) from [<c02507f8>] (pxa2xx_spi_suspend+0x2c/0x34) [<c02507f8>] (pxa2xx_spi_suspend) from [<c0200360>] (platform_pm_suspend+0x2c/0x54) [<c0200360>] (platform_pm_suspend) from [<c0207fec>] (dpm_run_callback.isra.14+0x2c/0x74) [<c0207fec>] (dpm_run_callback.isra.14) from [<c0209254>] (__device_suspend+0x120/0x2f8) [<c0209254>] (__device_suspend) from [<c0209a94>] (dpm_suspend+0x50/0x208) [<c0209a94>] (dpm_suspend) from [<c00455ac>] (suspend_devices_and_enter+0x8c/0x3a0) [<c00455ac>] (suspend_devices_and_enter) from [<c0045ad4>] (pm_suspend+0x214/0x2a8) [<c0045ad4>] (pm_suspend) from [<c04b5c34>] (test_suspend+0x14c/0x1dc) [<c04b5c34>] (test_suspend) from [<c000880c>] (do_one_initcall+0x8c/0x1fc) [<c000880c>] (do_one_initcall) from [<c04aecfc>] (kernel_init_freeable+0xf4/0x1b4) [<c04aecfc>] (kernel_init_freeable) from [<c0378078>] (kernel_init+0x8/0xec) [<c0378078>] (kernel_init) from [<c0009590>] (ret_from_fork+0x14/0x24) ---[ end trace 46524156d8faa4f6 ]--- This happens because suspend function tries to disable a clock that is already disabled by runtime_suspend callback. Add if (!pm_runtime_suspended()) checks to suspend/resume path. Fixes: 7d94a505 (spi/pxa2xx: add support for runtime PM) Signed-off-by:
Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Reported-by:
Andrea Adami <andrea.adami@gmail.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Imre Deak authored
commit 9e326f78 upstream. We can call this function for a dummy console that doesn't support setting the font mapping, which will result in a null ptr BUG. So check for this case and return error for consoles w/o font mapping support. Reference: https://bugzilla.kernel.org/show_bug.cgi?id=59321Signed-off-by:
Imre Deak <imre.deak@intel.com> Signed-off-by:
-
