- 27 Apr, 2017 19 commits
-
-
Yazen Ghannam authored
commit 29f72ce3 upstream. MCA bank 3 is reserved on systems pre-Fam17h, so it didn't have a name. However, MCA bank 3 is defined on Fam17h systems and can be accessed using legacy MSRs. Without a name we get a stack trace on Fam17h systems when trying to register sysfs files for bank 3 on kernels that don't recognize Scalable MCA. Call MCA bank 3 "decode_unit" since this is what it represents on Fam17h. This will allow kernels without SMCA support to see this bank on Fam17h+ and prevent the stack trace. This will not affect older systems since this bank is reserved on them, i.e. it'll be ignored. Tested on AMD Fam15h and Fam17h systems. WARNING: CPU: 26 PID: 1 at lib/kobject.c:210 kobject_add_internal kobject: (ffff88085bb256c0): attempted to be registered with empty name! ... Call Trace: kobject_add_internal kobject_add kobject_create_and_add threshold_create_device threshold_init_device Signed-off-by:
Yazen Ghannam <yazen.ghannam@amd.com> Signed-off-by:
Borislav Petkov <bp@suse.de> Link: http://lkml.kernel.org/r/1490102285-3659-1-git-send-email-Yazen.Ghannam@amd.comSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ravi Bangoria authored
commit 9e1ba4f2 upstream. If we set a kprobe on a 'stdu' instruction on powerpc64, we see a kernel OOPS: Bad kernel stack pointer cd93c840 at c000000000009868 Oops: Bad kernel stack pointer, sig: 6 [#1] ... GPR00: c000001fcd93cb30 00000000cd93c840 c0000000015c5e00 00000000cd93c840 ... NIP [c000000000009868] resume_kernel+0x2c/0x58 LR [c000000000006208] program_check_common+0x108/0x180 On a 64-bit system when the user probes on a 'stdu' instruction, the kernel does not emulate actual store in emulate_step() because it may corrupt the exception frame. So the kernel does the actual store operation in exception return code i.e. resume_kernel(). resume_kernel() loads the saved stack pointer from memory using lwz, which only loads the low 32-bits of the address, causing the kernel crash. Fix this by loading the 64-bit value instead. Fixes: be96f633 ("powerpc: Split out instruction analysis part of emulate_step()") Signed-off-by:
Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com> Reviewed-by:
Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Reviewed-by:
Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com> [mpe: Change log massage, add stable tag] Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Sebastian Siewior authored
commit 9cd9a21c upstream. In commit 6afaf8a4 ("UBI: flush wl before clearing update marker") I managed to trigger and fix a similar bug. Now here is another version of which I assumed it wouldn't matter back then but it turns out UBI has a check for it and will error out like this: |ubi0 warning: validate_vid_hdr: inconsistent used_ebs |ubi0 error: validate_vid_hdr: inconsistent VID header at PEB 592 All you need to trigger this is? "ubiupdatevol /dev/ubi0_0 file" + a powercut in the middle of the operation. ubi_start_update() sets the update-marker and puts all EBs on the erase list. After that userland can proceed to write new data while the old EB aren't erased completely. A powercut at this point is usually not that much of a tragedy. UBI won't give read access to the static volume because it has the update marker. It will most likely set the corrupted flag because it misses some EBs. So we are all good. Unless the size of the image that has been written differs from the old image in the magnitude of at least one EB. In that case UBI will find two different values for `used_ebs' and refuse to attach the image with the error message mentioned above. So in order not to get in the situation, the patch will ensure that we wait until everything is removed before it tries to write any data. The alternative would be to detect such a case and remove all EBs at the attached time after we processed the volume-table and see the update-marker set. The patch looks bigger and I doubt it is worth it since usually the write() will wait from time to time for a new EB since usually there not that many spare EB that can be used. Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
Richard Weinberger <richard@nod.at> Signed-off-by:
-
Johannes Berg authored
commit 3018e947 upstream. AP/AP_VLAN modes don't accept any real 802.11 multicast data frames, but since they do need to accept broadcast management frames the same is currently permitted for data frames. This opens a security problem because such frames would be decrypted with the GTK, and could even contain unicast L3 frames. Since the spec says that ToDS frames must always have the BSSID as the RA (addr1), reject any other data frames. The problem was originally reported in "Predicting, Decrypting, and Abusing WPA2/802.11 Group Keys" at usenix https://www.usenix.org/conference/usenixsecurity16/technical-sessions/presentation/vanhoef and brought to my attention by Jouni. Reported-by:
Jouni Malinen <j@w1.fi> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Haibo Chen authored
commit 9f327845 upstream. Currently for DDR50 card, it need tuning in default. We meet tuning fail issue for DDR50 card and some data CRC error when DDR50 sd card works. This is because the default pad I/O drive strength can't make sure DDR50 card work stable. So increase the pad I/O drive strength for DDR50 card, and use pins_100mhz. This fixes DDR50 card support for IMX since DDR50 tuning was enabled from commit 9faac7b9 ("mmc: sdhci: enable tuning for DDR50") Tested-and-reported-by:
Tim Harvey <tharvey@gateworks.com> Signed-off-by:
Haibo Chen <haibo.chen@nxp.com> Acked-by:
Dong Aisheng <aisheng.dong@nxp.com> Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Arnd Bergmann authored
commit fe8c470a upstream. gcc -O2 cannot always prove that the loop in acpi_power_get_inferred_state() is enterered at least once, so it assumes that cur_state might not get initialized: drivers/acpi/power.c: In function 'acpi_power_get_inferred_state': drivers/acpi/power.c:222:9: error: 'cur_state' may be used uninitialized in this function [-Werror=maybe-uninitialized] This sets the variable to zero at the start of the loop, to ensure that there is well-defined behavior even for an empty list. This gets rid of the warning. The warning first showed up when the -Os flag got removed in a bug fix patch in linux-4.11-rc5. I would suggest merging this addon patch on top of that bug fix to avoid introducing a new warning in the stable kernels. Fixes: 61b79e16 (ACPI: Fix incompatibility with mcount-based function graph tracing) Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Thorsten Leemhuis authored
commit 704de489 upstream. Temporary got a Lifebook E547 into my hands and noticed the touchpad only works after running: echo "1" > /sys/devices/platform/i8042/serio2/crc_enabled Add it to the list of machines that need this workaround. Signed-off-by:
Thorsten Leemhuis <linux@leemhuis.info> Reviewed-by:
Ulrik De Bie <ulrik.debie-os@e2big.org> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Jorgen Hansen authored
commit 8ab18d71 upstream. The check in vmci_transport_peer_detach_cb should only allow a detach when the qp handle of the transport matches the one in the detach message. Testing: Before this change, a detach from a peer on a different socket would cause an active stream socket to register a detach. Reviewed-by:
George Zhang <georgezhang@vmware.com> Signed-off-by:
Jorgen Hansen <jhansen@vmware.com> Signed-off-by:
-
K. Y. Srinivasan authored
commit 8de0d7e9 upstream. The current delay between retries is unnecessarily high and is negatively affecting the time it takes to boot the system. Signed-off-by:
K. Y. Srinivasan <kys@microsoft.com> Signed-off-by:
Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by:
-
Vitaly Kuznetsov authored
commit 396e287f upstream. vmbus_teardown_gpadl() can result in infinite wait when it is called on 5 second timeout in vmbus_open(). The issue is caused by the fact that gpadl teardown operation won't ever succeed for an opened channel and the timeout isn't always enough. As a guest, we can always trust the host to respond to our request (and there is nothing we can do if it doesn't). Signed-off-by:
Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by:
-
Vitaly Kuznetsov authored
commit 7cc80c98 upstream. In some cases create_gpadl_header() allocates submessages but we never free them. [sumits] Note for stable: Upstream commit 4d637632: (Drivers: hv: get rid of redundant messagecount in create_gpadl_header()) changes the list usage to initialize list header in all cases; that patch isn't added to stable, so the current patch is modified a little bit from the upstream commit to check if the list is valid or not. Signed-off-by:
-
Christian Borntraeger authored
commit a8f60d1f upstream. On heavy paging with KSM I see guest data corruption. Turns out that KSM will add pages to its tree, where the mapping return true for pte_unused (or might become as such later). KSM will unmap such pages and reinstantiate with different attributes (e.g. write protected or special, e.g. in replace_page or write_protect_page)). This uncovered a bug in our pagetable handling: We must remove the unused flag as soon as an entry becomes present again. Signed-of-by:
Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Germano Percossi authored
commit a0918f1c upstream. STATUS_BAD_NETWORK_NAME can be received during node failover, causing the flag to be set and making the reconnect thread always unsuccessful, thereafter. Once the only place where it is set is removed, the remaining bits are rendered moot. Removing it does not prevent "mount" from failing when a non existent share is passed. What happens when the share really ceases to exist while the share is mounted is undefined now as much as it was before. Signed-off-by:
Germano Percossi <germano.percossi@citrix.com> Reviewed-by:
Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by:
Steve French <smfrench@gmail.com> Signed-off-by:
-
Sachin Prabhu authored
commit 62a6cfdd upstream. commit 4fcd1813 ("Fix reconnect to not defer smb3 session reconnect long after socket reconnect") added support for Negotiate requests to be initiated by echo calls. To avoid delays in calling echo after a reconnect, I added the patch introduced by the commit b8c60012 ("Call echo service immediately after socket reconnect"). This has however caused a regression with cifs shares which do not have support for echo calls to trigger Negotiate requests. On connections which need to call Negotiation, the echo calls trigger an error which triggers a reconnect which in turn triggers another echo call. This results in a loop which is only broken when an operation is performed on the cifs share. For an idle share, it can DOS a server. The patch uses the smb_operation can_echo() for cifs so that it is called only if connection has been already been setup. kernel bz: 194531 Signed-off-by:
Sachin Prabhu <sprabhu@redhat.com> Tested-by:
Jonathan Liu <net147@gmail.com> Acked-by:
-
Steven Rostedt (VMware) authored
commit 78f7a45d upstream. I noticed that reading the snapshot file when it is empty no longer gives a status. It suppose to show the status of the snapshot buffer as well as how to allocate and use it. For example: ># cat snapshot # tracer: nop # # # * Snapshot is allocated * # # Snapshot commands: # echo 0 > snapshot : Clears and frees snapshot buffer # echo 1 > snapshot : Allocates snapshot buffer, if not already allocated. # Takes a snapshot of the main buffer. # echo 2 > snapshot : Clears snapshot buffer (but does not allocate or free) # (Doesn't have to be '2' works with any number that # is not a '0' or '1') But instead it just showed an empty buffer: ># cat snapshot # tracer: nop # # entries-in-buffer/entries-written: 0/0 #P:4 # # _-----=> irqs-off # / _----=> need-resched # | / _---=> hardirq/softirq # || / _--=> preempt-depth # ||| / delay # TASK-PID CPU# |||| TIMESTAMP FUNCTION # | | | |||| | | What happened was that it was using the ring_buffer_iter_empty() function to see if it was empty, and if it was, it showed the status. But that function was returning false when it was empty. The reason was that the iter header page was on the reader page, and the reader page was empty, but so was the buffer itself. The check only tested to see if the iter was on the commit page, but the commit page was no longer pointing to the reader page, but as all pages were empty, the buffer is also. Fixes: 651e22f2 ("ring-buffer: Always reset iterator to reader page") Signed-off-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by:
-
Steven Rostedt (VMware) authored
commit df62db5b upstream. Currently the snapshot trigger enables the probe and then allocates the snapshot. If the probe triggers before the allocation, it could cause the snapshot to fail and turn tracing off. It's best to allocate the snapshot buffer first, and then enable the trigger. If something goes wrong in the enabling of the trigger, the snapshot buffer is still allocated, but it can also be freed by the user by writting zero into the snapshot buffer file. Also add a check of the return status of alloc_snapshot(). Fixes: 77fd5c15 ("tracing: Add snapshot trigger to function probes") Signed-off-by:
-
Eric Biggers authored
commit c9f838d1 upstream. This fixes CVE-2017-7472. Running the following program as an unprivileged user exhausts kernel memory by leaking thread keyrings: #include <keyutils.h> int main() { for (;;) keyctl_set_reqkey_keyring(KEY_REQKEY_DEFL_THREAD_KEYRING); } Fix it by only creating a new thread keyring if there wasn't one before. To make things more consistent, make install_thread_keyring_to_cred() and install_process_keyring_to_cred() both return 0 if the corresponding keyring is already present. Fixes: d84f4f99 ("CRED: Inaugurate COW credentials") Signed-off-by:
Eric Biggers <ebiggers@google.com> Signed-off-by:
David Howells <dhowells@redhat.com> Signed-off-by:
-
David Howells authored
commit c1644fe0 upstream. This fixes CVE-2017-6951. Userspace should not be able to do things with the "dead" key type as it doesn't have some of the helper functions set upon it that the kernel needs. Attempting to use it may cause the kernel to crash. Fix this by changing the name of the type to ".dead" so that it's rejected up front on userspace syscalls by key_get_type_from_user(). Though this doesn't seem to affect recent kernels, it does affect older ones, certainly those prior to: commit c06cfb08 Author: David Howells <dhowells@redhat.com> Date: Tue Sep 16 17:36:06 2014 +0100 KEYS: Remove key_type::match in favour of overriding default by match_preparse which went in before 3.18-rc1. Signed-off-by:
-
David Howells authored
commit ee8f844e upstream. This fixes CVE-2016-9604. Keyrings whose name begin with a '.' are special internal keyrings and so userspace isn't allowed to create keyrings by this name to prevent shadowing. However, the patch that added the guard didn't fix KEYCTL_JOIN_SESSION_KEYRING. Not only can that create dot-named keyrings, it can also subscribe to them as a session keyring if they grant SEARCH permission to the user. This, for example, allows a root process to set .builtin_trusted_keys as its session keyring, at which point it has full access because now the possessor permissions are added. This permits root to add extra public keys, thereby bypassing module verification. This also affects kexec and IMA. This can be tested by (as root): keyctl session .builtin_trusted_keys keyctl add user a a @s keyctl list @s which on my test box gives me: 2 keys in keyring: 180010936: ---lswrv 0 0 asymmetric: Build time autogenerated kernel key: ae3d4a31b82daa8e1a75b49dc2bba949fd992a05 801382539: --alswrv 0 0 user: a Fix this by rejecting names beginning with a '.' in the keyctl. Signed-off-by:
Mimi Zohar <zohar@linux.vnet.ibm.com> cc: linux-ima-devel@lists.sourceforge.net Signed-off-by:
-
- 21 Apr, 2017 21 commits
-
-
Greg Kroah-Hartman authored
-
Greg Kroah-Hartman authored
Commit f017e58d which was commit 3cc3434f upstream, was misapplied to the 4.4 stable kernel. This patch fixes this and moves the chunk to the proper Kconfig area. Reported-by:
"Maciej W. Rozycki" <macro@linux-mips.org> Cc: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Jason A. Donenfeld <jason@zx2c4.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Amit Pundir <amit.pundir@linaro.org> Signed-off-by:
-
Marcelo Ricardo Leitner authored
commit dfcb9f4f upstream. commit 2dcab598 ("sctp: avoid BUG_ON on sctp_wait_for_sndbuf") attempted to avoid a BUG_ON call when the association being used for a sendmsg() is blocked waiting for more sndbuf and another thread did a peeloff operation on such asoc, moving it to another socket. As Ben Hutchings noticed, then in such case it would return without locking back the socket and would cause two unlocks in a row. Further analysis also revealed that it could allow a double free if the application managed to peeloff the asoc that is created during the sendmsg call, because then sctp_sendmsg() would try to free the asoc that was created only for that call. This patch takes another approach. It will deny the peeloff operation if there is a thread sleeping on the asoc, so this situation doesn't exist anymore. This avoids the issues described above and also honors the syscalls that are already being handled (it can be multiple sendmsg calls). Joint work with Xin Long. Fixes: 2dcab598 ("sctp: avoid BUG_ON on sctp_wait_for_sndbuf") Cc: Alexander Popov <alex.popov@linux.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
-
Mantas M authored
commit c2ed1880 upstream. The protocol field is checked when deleting IPv4 routes, but ignored for IPv6, which causes problems with routing daemons accidentally deleting externally set routes (observed by multiple bird6 users). This can be verified using `ip -6 route del <prefix> proto something`. Signed-off-by:
Mantas Mikulėnas <grawity@gmail.com> Signed-off-by:
-
Richard Genoud authored
commit b389f173 upstream. When using RS485 in half duplex, RX should be enabled when TX is finished, and stopped when TX starts. Before commit 0058f087 ("tty/serial: atmel: fix RS485 half duplex with DMA"), RX was not disabled in atmel_start_tx() if the DMA was used. So, collisions could happened. But disabling RX in atmel_start_tx() uncovered another bug: RX was enabled again in the wrong place (in atmel_tx_dma) instead of being enabled when TX is finished (in atmel_complete_tx_dma), so the transmission simply stopped. This bug was not triggered before commit 0058f087 ("tty/serial: atmel: fix RS485 half duplex with DMA") because RX was never disabled before. Moving atmel_start_rx() in atmel_complete_tx_dma() corrects the problem. Reported-by:
Gil Weber <webergil@gmail.com> Fixes: 0058f087Tested-by:
Richard Genoud <richard.genoud@gmail.com> Acked-by:
Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by:
Bryan Evenson <bevenson@melinkcorp.com> Signed-off-by:
-
NeilBrown authored
commit 1cded9d2 upstream. There are two problems with refcounting of auth_gss messages. First, the reference on the pipe->pipe list (taken by a call to rpc_queue_upcall()) is not counted. It seems to be assumed that a message in pipe->pipe will always also be in pipe->in_downcall, where it is correctly reference counted. However there is no guaranty of this. I have a report of a NULL dereferences in rpc_pipe_read() which suggests a msg that has been freed is still on the pipe->pipe list. One way I imagine this might happen is: - message is queued for uid=U and auth->service=S1 - rpc.gssd reads this message and starts processing. This removes the message from pipe->pipe - message is queued for uid=U and auth->service=S2 - rpc.gssd replies to the first message. gss_pipe_downcall() calls __gss_find_upcall(pipe, U, NULL) and it finds the *second* message, as new messages are placed at the head of ->in_downcall, and the service type is not checked. - This second message is removed from ->in_downcall and freed by gss_release_msg() (even though it is still on pipe->pipe) - rpc.gssd tries to read another message, and dereferences a pointer to this message that has just been freed. I fix this by incrementing the reference count before calling rpc_queue_upcall(), and decrementing it if that fails, or normally in gss_pipe_destroy_msg(). It seems strange that the reply doesn't target the message more precisely, but I don't know all the details. In any case, I think the reference counting irregularity became a measureable bug when the extra arg was added to __gss_find_upcall(), hence the Fixes: line below. The second problem is that if rpc_queue_upcall() fails, the new message is not freed. gss_alloc_msg() set the ->count to 1, gss_add_msg() increments this to 2, gss_unhash_msg() decrements to 1, then the pointer is discarded so the memory never gets freed. Fixes: 9130b8db ("SUNRPC: allow for upcalls for same uid but different gss service") Link: https://bugzilla.opensuse.org/show_bug.cgi?id=1011250Signed-off-by:
NeilBrown <neilb@suse.com> Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by:
-
Thomas Falcon authored
commit 94acf164 upstream. Include calculations to compute the number of segments that comprise an aggregated large packet. Signed-off-by:
Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Reviewed-by:
Jonathan Maxwell <jmaxwell37@gmail.com> Signed-off-by:
-
Ben Hutchings authored
commit 2d6a0e9d upstream. Allocating USB buffers on the stack is not portable, and no longer works on x86_64 (with VMAP_STACK enabled as per default). Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Ben Hutchings authored
commit d4114914 upstream. Signed-off-by:
-
Ben Hutchings authored
commit 7926aff5 upstream. Allocating USB buffers on the stack is not portable, and no longer works on x86_64 (with VMAP_STACK enabled as per default). Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Ben Hutchings authored
commit 5593523f upstream. Allocating USB buffers on the stack is not portable, and no longer works on x86_64 (with VMAP_STACK enabled as per default). Fixes: 1da177e4 ("Linux-2.6.12-rc2") References: https://bugs.debian.org/852556Reported-by:
Lisandro Damián Nicanor Pérez Meyer <lisandro@debian.org> Tested-by:
-
Omar Sandoval authored
commit c4baad50 upstream. put_chars() stuffs the buffer it gets into an sg, but that buffer may be on the stack. This breaks with CONFIG_VMAP_STACK=y (for me, it manifested as printks getting turned into NUL bytes). Signed-off-by:
Omar Sandoval <osandov@fb.com> Signed-off-by:
Michael S. Tsirkin <mst@redhat.com> Reviewed-by:
Amit Shah <amit.shah@redhat.com> Cc: Ben Hutchings <ben@decadent.org.uk> Cc: Brad Spengler <spender@grsecurity.net> Signed-off-by:
-
Stefan Brüns authored
commit 67b0503d upstream. The buffer allocation for the firmware data was changed in commit 43fab979 ("[media] dvb-usb: don't use stack for firmware load") but the same applies for the reset value. Fixes: 43fab979 ("[media] dvb-usb: don't use stack for firmware load") Signed-off-by:
Stefan Brüns <stefan.bruens@rwth-aachen.de> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com> Cc: Ben Hutchings <ben@decadent.org.uk> Cc: Brad Spengler <spender@grsecurity.net> Signed-off-by:
-
Mauro Carvalho Chehab authored
commit 43fab979 upstream. As reported by Marc Duponcheel <marc@offline.be>, firmware load on dvb-usb is using the stack, with is not allowed anymore on default Kernel configurations: [ 1025.958836] dvb-usb: found a 'WideView WT-220U PenType Receiver (based on ZL353)' in cold state, will try to load a firmware [ 1025.958853] dvb-usb: downloading firmware from file 'dvb-usb-wt220u-zl0353-01.fw' [ 1025.958855] dvb-usb: could not stop the USB controller CPU. [ 1025.958856] dvb-usb: error while transferring firmware (transferred size: -11, block size: 3) [ 1025.958856] dvb-usb: firmware download failed at 8 with -22 [ 1025.958867] usbcore: registered new interface driver dvb_usb_dtt200u [ 2.789902] dvb-usb: downloading firmware from file 'dvb-usb-wt220u-zl0353-01.fw' [ 2.789905] ------------[ cut here ]------------ [ 2.789911] WARNING: CPU: 3 PID: 2196 at drivers/usb/core/hcd.c:1584 usb_hcd_map_urb_for_dma+0x430/0x560 [usbcore] [ 2.789912] transfer buffer not dma capable [ 2.789912] Modules linked in: btusb dvb_usb_dtt200u(+) dvb_usb_af9035(+) btrtl btbcm dvb_usb dvb_usb_v2 btintel dvb_core bluetooth rc_core rfkill x86_pkg_temp_thermal intel_powerclamp coretemp crc32_pclmul aesni_intel aes_x86_64 glue_helper lrw gf128mul ablk_helper cryptd drm_kms_helper syscopyarea sysfillrect pcspkr i2c_i801 sysimgblt fb_sys_fops drm i2c_smbus i2c_core r8169 lpc_ich mfd_core mii thermal fan rtc_cmos video button acpi_cpufreq processor snd_hda_codec_realtek snd_hda_codec_generic snd_hda_intel snd_hda_codec snd_hwdep snd_hda_core snd_pcm snd_timer snd crc32c_intel ahci libahci libata xhci_pci ehci_pci xhci_hcd ehci_hcd usbcore usb_common dm_mirror dm_region_hash dm_log dm_mod [ 2.789936] CPU: 3 PID: 2196 Comm: systemd-udevd Not tainted 4.9.0-gentoo #1 [ 2.789937] Hardware name: ASUS All Series/H81I-PLUS, BIOS 0401 07/23/2013 [ 2.789938] ffffc9000339b690 ffffffff812bd397 ffffc9000339b6e0 0000000000000000 [ 2.789939] ffffc9000339b6d0 ffffffff81055c86 000006300339b6a0 ffff880116c0c000 [ 2.789941] 0000000000000000 0000000000000000 0000000000000001 ffff880116c08000 [ 2.789942] Call Trace: [ 2.789945] [<ffffffff812bd397>] dump_stack+0x4d/0x66 [ 2.789947] [<ffffffff81055c86>] __warn+0xc6/0xe0 [ 2.789948] [<ffffffff81055cea>] warn_slowpath_fmt+0x4a/0x50 [ 2.789952] [<ffffffffa006d460>] usb_hcd_map_urb_for_dma+0x430/0x560 [usbcore] [ 2.789954] [<ffffffff814ed5a8>] ? io_schedule_timeout+0xd8/0x110 [ 2.789956] [<ffffffffa006e09c>] usb_hcd_submit_urb+0x9c/0x980 [usbcore] [ 2.789958] [<ffffffff812d0ebf>] ? copy_page_to_iter+0x14f/0x2b0 [ 2.789960] [<ffffffff81126818>] ? pagecache_get_page+0x28/0x240 [ 2.789962] [<ffffffff8118c2a0>] ? touch_atime+0x20/0xa0 [ 2.789964] [<ffffffffa006f7c4>] usb_submit_urb+0x2c4/0x520 [usbcore] [ 2.789967] [<ffffffffa006feca>] usb_start_wait_urb+0x5a/0xe0 [usbcore] [ 2.789969] [<ffffffffa007000c>] usb_control_msg+0xbc/0xf0 [usbcore] [ 2.789970] [<ffffffffa067903d>] usb_cypress_writemem+0x3d/0x40 [dvb_usb] [ 2.789972] [<ffffffffa06791cf>] usb_cypress_load_firmware+0x4f/0x130 [dvb_usb] [ 2.789973] [<ffffffff8109dbbe>] ? console_unlock+0x2fe/0x5d0 [ 2.789974] [<ffffffff8109e10c>] ? vprintk_emit+0x27c/0x410 [ 2.789975] [<ffffffff8109e40a>] ? vprintk_default+0x1a/0x20 [ 2.789976] [<ffffffff81124d76>] ? printk+0x43/0x4b [ 2.789977] [<ffffffffa0679310>] dvb_usb_download_firmware+0x60/0xd0 [dvb_usb] [ 2.789979] [<ffffffffa0679898>] dvb_usb_device_init+0x3d8/0x610 [dvb_usb] [ 2.789981] [<ffffffffa069e302>] dtt200u_usb_probe+0x92/0xd0 [dvb_usb_dtt200u] [ 2.789984] [<ffffffffa007420c>] usb_probe_interface+0xfc/0x270 [usbcore] [ 2.789985] [<ffffffff8138bf95>] driver_probe_device+0x215/0x2d0 [ 2.789986] [<ffffffff8138c0e6>] __driver_attach+0x96/0xa0 [ 2.789987] [<ffffffff8138c050>] ? driver_probe_device+0x2d0/0x2d0 [ 2.789988] [<ffffffff81389ffb>] bus_for_each_dev+0x5b/0x90 [ 2.789989] [<ffffffff8138b7b9>] driver_attach+0x19/0x20 [ 2.789990] [<ffffffff8138b33c>] bus_add_driver+0x11c/0x220 [ 2.789991] [<ffffffff8138c91b>] driver_register+0x5b/0xd0 [ 2.789994] [<ffffffffa0072f6c>] usb_register_driver+0x7c/0x130 [usbcore] [ 2.789994] [<ffffffffa06a5000>] ? 0xffffffffa06a5000 [ 2.789996] [<ffffffffa06a501e>] dtt200u_usb_driver_init+0x1e/0x20 [dvb_usb_dtt200u] [ 2.789997] [<ffffffff81000408>] do_one_initcall+0x38/0x140 [ 2.789998] [<ffffffff8116001c>] ? __vunmap+0x7c/0xc0 [ 2.789999] [<ffffffff81124fb0>] ? do_init_module+0x22/0x1d2 [ 2.790000] [<ffffffff81124fe8>] do_init_module+0x5a/0x1d2 [ 2.790002] [<ffffffff810c96b1>] load_module+0x1e11/0x2580 [ 2.790003] [<ffffffff810c68b0>] ? show_taint+0x30/0x30 [ 2.790004] [<ffffffff81177250>] ? kernel_read_file+0x100/0x190 [ 2.790005] [<ffffffff810c9ffa>] SyS_finit_module+0xba/0xc0 [ 2.790007] [<ffffffff814f13e0>] entry_SYSCALL_64_fastpath+0x13/0x94 [ 2.790008] ---[ end trace c78a74e78baec6fc ]--- So, allocate the structure dynamically. Signed-off-by:
-
Kees Cook authored
commit a4866aa8 upstream. Under CONFIG_STRICT_DEVMEM, reading System RAM through /dev/mem is disallowed. However, on x86, the first 1MB was always allowed for BIOS and similar things, regardless of it actually being System RAM. It was possible for heap to end up getting allocated in low 1MB RAM, and then read by things like x86info or dd, which would trip hardened usercopy: usercopy: kernel memory exposure attempt detected from ffff880000090000 (dma-kmalloc-256) (4096 bytes) This changes the x86 exception for the low 1MB by reading back zeros for System RAM areas instead of blindly allowing them. More work is needed to extend this to mmap, but currently mmap doesn't go through usercopy, so hardened usercopy won't Oops the kernel. Reported-by:
Tommi Rantala <tommi.t.rantala@nokia.com> Tested-by:
Kees Cook <keescook@chromium.org> Cc: Brad Spengler <spender@grsecurity.net> Signed-off-by:
-
Thierry Reding authored
commit 5fa40869 upstream. Accessing the registers of the RTC block on Tegra requires the module clock to be enabled. This only works because the RTC module clock will be enabled by default during early boot. However, because the clock is unused, the CCF will disable it at late_init time. This causes the RTC to become unusable afterwards. This can easily be reproduced by trying to use the RTC: $ hwclock --rtc /dev/rtc1 This will hang the system. I ran into this by following up on a report by Martin Michlmayr that reboot wasn't working on Tegra210 systems. It turns out that the rtc-tegra driver's ->shutdown() implementation will hang the CPU, because of the disabled clock, before the system can be rebooted. What confused me for a while is that the same driver is used on prior Tegra generations where the hang can not be observed. However, as Peter De Schrijver pointed out, this is because on 32-bit Tegra chips the RTC clock is enabled by the tegra20_timer.c clocksource driver, which uses the RTC to provide a persistent clock. This code is never enabled on 64-bit Tegra because the persistent clock infrastructure does not exist on 64-bit ARM. The proper fix for this is to add proper clock handling to the RTC driver in order to ensure that the clock is enabled when the driver requires it. All device trees contain the clock already, therefore no additional changes are required. Reported-by:
Martin Michlmayr <tbm@cyrius.com> Acked-By Peter De Schrijver <pdeschrijver@nvidia.com> Signed-off-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
-
Lee, Chun-Yi authored
commit 98d610c3 upstream. The accelerometer event relies on the ACERWMID_EVENT_GUID notify. So, this patch changes the codes to setup accelerometer input device when detected ACERWMID_EVENT_GUID. It avoids that the accel input device created on every Acer machines. In addition, patch adds a clearly parsing logic of accelerometer hid to acer_wmi_get_handle_cb callback function. It is positive matching the "SENR" name with "BST0001" device to avoid non-supported hardware. Reported-by:
Bjørn Mork <bjorn@mork.no> Cc: Darren Hart <dvhart@infradead.org> Signed-off-by:
Lee, Chun-Yi <jlee@suse.com> [andy: slightly massage commit message] Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Daeho Jeong authored
commit 05ac5aa1 upstream. We've fixed the race condition problem in calculating ext4 checksum value in commit b47820ed ("ext4: avoid modifying checksum fields directly during checksum veficationon"). However, by this change, when calculating the checksum value of inode whose i_extra_size is less than 4, we couldn't calculate the checksum value in a proper way. This problem was found and reported by Nix, Thank you. Reported-by:
Nix <nix@esperi.org.uk> Signed-off-by:
Daeho Jeong <daeho.jeong@samsung.com> Signed-off-by:
Youngjin Gil <youngjin.gil@samsung.com> Signed-off-by:
Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Arnd Bergmann authored
commit 00514537 upstream. I ran into a stack frame size warning because of the on-stack copy of the USB device structure: drivers/media/usb/dvb-usb-v2/dvb_usb_core.c: In function 'dvb_usbv2_disconnect': drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:1029:1: error: the frame size of 1104 bytes is larger than 1024 bytes [-Werror=frame-larger-than=] Copying a device structure like this is wrong for a number of other reasons too aside from the possible stack overflow. One of them is that the dev_info() call will print the name of the device later, but AFAICT we have only copied a pointer to the name earlier and the actual name has been freed by the time it gets printed. This removes the on-stack copy of the device and instead copies the device name using kstrdup(). I'm ignoring the possible failure here as both printk() and kfree() are able to deal with NULL pointers. Signed-off-by:
-
Miaoqing Pan authored
commit 40bea976 upstream. relay_open() may return NULL, check the return value to avoid the crash. BUG: unable to handle kernel NULL pointer dereference at 0000000000000040 IP: [<ffffffffa01a95c5>] ath_cmn_process_fft+0xd5/0x700 [ath9k_common] PGD 41cf28067 PUD 41be92067 PMD 0 Oops: 0000 [#1] SMP CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.8.6+ #35 Hardware name: Hewlett-Packard h8-1080t/2A86, BIOS 6.15 07/04/2011 task: ffffffff81e0c4c0 task.stack: ffffffff81e00000 RIP: 0010:[<ffffffffa01a95c5>] [<ffffffffa01a95c5>] ath_cmn_process_fft+0xd5/0x700 [ath9k_common] RSP: 0018:ffff88041f203ca0 EFLAGS: 00010293 RAX: 0000000000000000 RBX: 000000000000059f RCX: 0000000000000000 RDX: 0000000000000000 RSI: 0000000000000040 RDI: ffffffff81f0ca98 RBP: ffff88041f203dc8 R08: ffffffffffffffff R09: 00000000000000ff R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000 R13: ffffffff81f0ca98 R14: 0000000000000000 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffff88041f200000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000040 CR3: 000000041b6ec000 CR4: 00000000000006f0 Stack: 0000000000000363 00000000000003f3 00000000000003f3 00000000000001f9 000000000000049a 0000000001252c04 ffff88041f203e44 ffff880417b4bfd0 0000000000000008 ffff88041785b9c0 0000000000000002 ffff88041613dc60 Call Trace: <IRQ> [<ffffffffa01b6441>] ath9k_tasklet+0x1b1/0x220 [ath9k] [<ffffffff8105d8dd>] tasklet_action+0x4d/0xf0 [<ffffffff8105dde2>] __do_softirq+0x92/0x2a0 Reported-by:
Devin Tuchsen <devin.tuchsen@gmail.com> Tested-by:
Miaoqing Pan <miaoqing@codeaurora.org> Signed-off-by:
Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by:
-
Herbert Xu authored
commit ef0579b6 upstream. The ahash API modifies the request's callback function in order to clean up after itself in some corner cases (unaligned final and missing finup). When the request is complete ahash will restore the original callback and everything is fine. However, when the request gets an EBUSY on a full queue, an EINPROGRESS callback is made while the request is still ongoing. In this case the ahash API will incorrectly call its own callback. This patch fixes the problem by creating a temporary request object on the stack which is used to relay EINPROGRESS back to the original completion function. This patch also adds code to preserve the original flags value. Fixes: ab6bf4e5 ("crypto: hash - Fix the pointer voodoo in...") Reported-by:
Sabrina Dubroca <sd@queasysnail.net> Tested-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
