- 30 Oct, 2014 1 commit
-
-
Lu Baolu authored
commit ddbe1fca upstream. This full-speed USB device generates spurious remote wakeup event as soon as USB_DEVICE_REMOTE_WAKEUP feature is set. As the result, Linux can't enter system suspend and S0ix power saving modes once this keyboard is used. This patch tries to introduce USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk. With this quirk set, wakeup capability will be ignored during device configure. This patch could be back-ported to kernels as old as 2.6.39. Signed-off-by:
Lu Baolu <baolu.lu@linux.intel.com> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Jiri Slaby <jslaby@suse.cz>
-
- 29 Oct, 2014 1 commit
-
-
Eliad Peller authored
Upstream commit a5fe8e76 (regulatory: add NUL to alpha2) contained a hunk that was supposed to be applied to struct ieee80211_reg_rule. However in stable 3.12 (3.12.31 in particular), it ended up in struct regulatory_request. Fix that now. Signed-off-by:
-
- 17 Oct, 2014 32 commits
-
-
Pali Rohár authored
commit a666b6ff upstream. Without this patch, dell-wmi is trying to access elements of dynamically allocated array without checking the array size. This can lead to memory corruption or a kernel panic. This patch adds the missing checks for array size. Signed-off-by:
Pali Rohár <pali.rohar@gmail.com> Signed-off-by:
Darren Hart <dvhart@linux.intel.com> Signed-off-by:
-
Andy Lutomirski authored
commit a1480dcc upstream. Accessing do_remount_sb should require global CAP_SYS_ADMIN, but only one of the two call sites was appropriately protected. Fixes CVE-2014-7975. Signed-off-by:
Andy Lutomirski <luto@amacapital.net> Signed-off-by:
-
Jiri Slaby authored
-
Bryan O'Donoghue authored
commit 1ede7dcc upstream. Quark X1000 contains two designware derived 8250 serial ports. Each port has a unique PCI configuration space consisting of BAR0:UART BAR1:DMA respectively. Unlike the standard 8250 the register width is 32 bits for RHR,IER etc The Quark UART has a fundamental clock @ 44.2368 MHz allowing for a bitrate of up to about 2.76 megabits per second. This patch enables standard 8250 mode Signed-off-by:
Bryan O'Donoghue <pure.logic@nexus-software.ie> Reviewed-by:
Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by:
-
Andreas Bomholtz authored
commit dee80ad1 upstream. Added the Seluxit ApS USB Serial Dongle to cp210x driver. Signed-off-by:
Andreas Bomholtz <andreas@seluxit.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Joe Savage authored
commit bfc2d7df upstream. Added support for Ketra N1 wireless interface, which uses the Silicon Labs' CP2104 USB to UART bridge with customized PID 8946. Signed-off-by:
Joe Savage <joe.savage@goketra.com> Signed-off-by:
-
Lu Baolu authored
commit ddbe1fca upstream. This full-speed USB device generates spurious remote wakeup event as soon as USB_DEVICE_REMOTE_WAKEUP feature is set. As the result, Linux can't enter system suspend and S0ix power saving modes once this keyboard is used. This patch tries to introduce USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk. With this quirk set, wakeup capability will be ignored during device configure. This patch could be back-ported to kernels as old as 2.6.39. Signed-off-by:
-
Per Hurtig authored
[ Upstream commit bef1909e ] Fix to a problem observed when losing a FIN segment that does not contain data. In such situations, TLP is unable to recover from *any* tail loss and instead adds at least PTO ms to the retransmission process, i.e., RTO = RTO + PTO. Signed-off-by:
Per Hurtig <per.hurtig@kau.se> Signed-off-by:
Eric Dumazet <edumazet@google.com> Acked-by:
Nandita Dukkipati <nanditad@google.com> Acked-by:
Neal Cardwell <ncardwell@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Vlad Yasevich authored
[ Upstream commit bdf6fa52 ] Currently association restarts do not take into consideration the state of the socket. When a restart happens, the current assocation simply transitions into established state. This creates a condition where a remote system, through a the restart procedure, may create a local association that is no way reachable by user. The conditions to trigger this are as follows: 1) Remote does not acknoledge some data causing data to remain outstanding. 2) Local application calls close() on the socket. Since data is still outstanding, the association is placed in SHUTDOWN_PENDING state. However, the socket is closed. 3) The remote tries to create a new association, triggering a restart on the local system. The association moves from SHUTDOWN_PENDING to ESTABLISHED. At this point, it is no longer reachable by any socket on the local system. This patch addresses the above situation by moving the newly ESTABLISHED association into SHUTDOWN-SENT state and bundling a SHUTDOWN after the COOKIE-ACK chunk. This way, the restarted associate immidiately enters the shutdown procedure and forces the termination of the unreachable association. Reported-by:
David Laight <David.Laight@aculab.com> Signed-off-by:
Vlad Yasevich <vyasevich@gmail.com> Signed-off-by:
-
Joe Lawrence authored
[ Upstream commit 47549650 ] When team_notify_peers and team_mcast_rejoin are called, they both reset their respective .count_pending atomic variable. Then when the actual worker function is executed, the variable is atomically decremented. This pattern introduces a potential race condition where the .count_pending rolls over and the worker function keeps rescheduling until .count_pending decrements to zero again: THREAD 1 THREAD 2 ======== ======== team_notify_peers(teamX) atomic_set count_pending = 1 schedule_delayed_work team_notify_peers(teamX) atomic_set count_pending = 1 team_notify_peers_work atomic_dec_and_test count_pending = 0 (return) schedule_delayed_work team_notify_peers_work atomic_dec_and_test count_pending = -1 schedule_delayed_work (repeat until count_pending = 0) Instead of assigning a new value to .count_pending, use atomic_add to tack-on the additional desired worker function invocations. Signed-off-by:
Joe Lawrence <joe.lawrence@stratus.com> Acked-by:
Jiri Pirko <jiri@resnulli.us> Fixes: fc423ff0 ("team: add peer notification") Fixes: 492b200e ("team: add support for sending multicast rejoins") Signed-off-by:
-
Nicolas Dichtel authored
[ Upstream commit 3be07244 ] In xmit path, we build a flowi6 which will be used for the output route lookup. We are sending a GRE packet, neither IPv4 nor IPv6 encapsulated packet, thus the protocol should be IPPROTO_GRE. Fixes: c12b395a ("gre: Support GRE over IPv6") Reported-by:
Matthieu Ternisien d'Ouville <matthieu.tdo@6wind.com> Signed-off-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by:
-
KY Srinivasan authored
[ Upstream commit dedb845d ] After the packet is successfully sent, we should not touch the skb as it may have been freed. This patch is based on the work done by Long Li <longli@microsoft.com>. In this version of the patch I have fixed issues pointed out by David. David, please queue this up for stable. Signed-off-by:
K. Y. Srinivasan <kys@microsoft.com> Tested-by:
Long Li <longli@microsoft.com> Tested-by:
Sitsofe Wheeler <sitsofe@yahoo.com> Signed-off-by:
-
Soren Brinkmann authored
[ Upstream commit 9026968a ] This reverts commit 8ef29f8a. The driver core already calls pinctrl_get() and claims the default state. There is no need to replicate this in the driver. Acked-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by:
-
Vlad Yasevich authored
[ Upstream commit 40b8fe45 ] In macvtap device delete and open calls can race and this causes a list curruption of the vlan queue_list. The race intself is triggered by the idr accessors that located the vlan device. The device is stored into and removed from the idr under both an rtnl and a mutex. However, when attempting to locate the device in idr, only a mutex is taken. As a result, once cpu perfoming a delete may take an rtnl and wait for the mutex, while another cput doing an open() will take the idr mutex first to fetch the device pointer and later take an rtnl to add a queue for the device which may have just gotten deleted. With this patch, we now hold the rtnl for the duration of the macvtap_open() call thus making sure that open will not race with delete. CC: Michael S. Tsirkin <mst@redhat.com> CC: Jason Wang <jasowang@redhat.com> Signed-off-by:
Vladislav Yasevich <vyasevic@redhat.com> Acked-by:
Jason Wang <jasowang@redhat.com> Acked-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
-
Steffen Klassert authored
[ Upstream commit b8c203b2 ] Currently we genarate a queueing route if we have matching policies but can not resolve the states and the sysctl xfrm_larval_drop is disabled. Here we assume that dst_output() is called to kill the queued packets. Unfortunately this assumption is not true in all cases, so it is possible that these packets leave the system unwanted. We fix this by generating queueing routes only from the route lookup functions, here we can guarantee a call to dst_output() afterwards. Fixes: a0073fe1 ("xfrm: Add a state resolution packet queue") Reported-by:
Konstantinos Kolelis <k.kolelis@sirrix.com> Signed-off-by:
Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by:
-
Steffen Klassert authored
[ Upstream commit f92ee619 ] Currently we genarate a blackhole route route whenever we have matching policies but can not resolve the states. Here we assume that dst_output() is called to kill the balckholed packets. Unfortunately this assumption is not true in all cases, so it is possible that these packets leave the system unwanted. We fix this by generating blackhole routes only from the route lookup functions, here we can guarantee a call to dst_output() afterwards. Fixes: 2774c131 ("xfrm: Handle blackhole route creation via afinfo.") Reported-by:
-
Vlad Yasevich authored
[ Upstream commit 7d3083ee ] When receiving a vlan-tagged frame that still contains a vlan header, the length of the packet will be greater then MTU+ETH_HLEN since it will account of the extra vlan header. TG3 checks this for the case for 802.1Q, but not for 802.1ad. As a result, full sized 802.1ad frames get dropped by the card. Add a check for 802.1ad protocol when receving full sized frames. Suggested-by:
Prashant Sreedharan <prashant@broadcom.com> CC: Prashant Sreedharan <prashant@broadcom.com> CC: Michael Chan <mchan@broadcom.com> Signed-off-by:
-
Vlad Yasevich authored
[ Upstream commit 476c1885 ] TG3 appears to have an issue performing TSO and checksum offloading correclty when the frame has been vlan encapsulated (non-accelrated). In these cases, tcp checksum is not correctly updated. This patch attempts to work around this issue. After the patch, 802.1ad vlans start working correctly over tg3 devices. CC: Prashant Sreedharan <prashant@broadcom.com> CC: Michael Chan <mchan@broadcom.com> Signed-off-by:
-
Vlad Yasevich authored
[ Upstream commit c095f248 ] As Toshiaki Makita pointed out, the BRIDGE_INPUT_SKB_CB will not be initialized in br_should_learn() as that function is called only from br_handle_local_finish(). That is an input handler for link-local ethernet traffic so it perfectly correct to check br->vlan_enabled here. Reported-by: Toshiaki Makita<toshiaki.makita1@gmail.com> Fixes: 20adfa1a bridge: Check if vlan filtering is enabled only once. Signed-off-by:
-
Vlad Yasevich authored
[ Upstream commit 20adfa1a ] The bridge code checks if vlan filtering is enabled on both ingress and egress. When the state flip happens, it is possible for the bridge to currently be forwarding packets and forwarding behavior becomes non-deterministic. Bridge may drop packets on some interfaces, but not others. This patch solves this by caching the filtered state of the packet into skb_cb on ingress. The skb_cb is guaranteed to not be over-written between the time packet entres bridge forwarding path and the time it leaves it. On egress, we can then check the cached state to see if we need to apply filtering information. Signed-off-by:
-
Guillaume Nault authored
[ Upstream commit eed4d839 ] Use dst_entry held by sk_dst_get() to retrieve tunnel's PMTU. The dst_mtu(__sk_dst_get(tunnel->sock)) call was racy. __sk_dst_get() could return NULL if tunnel->sock->sk_dst_cache was reset just before the call, thus making dst_mtu() dereference a NULL pointer: [ 1937.661598] BUG: unable to handle kernel NULL pointer dereference at 0000000000000020 [ 1937.664005] IP: [<ffffffffa049db88>] pppol2tp_connect+0x33d/0x41e [l2tp_ppp] [ 1937.664005] PGD daf0c067 PUD d9f93067 PMD 0 [ 1937.664005] Oops: 0000 [#1] SMP [ 1937.664005] Modules linked in: l2tp_ppp l2tp_netlink l2tp_core ip6table_filter ip6_tables iptable_filter ip_tables ebtable_nat ebtables x_tables udp_tunnel pppoe pppox ppp_generic slhc deflate ctr twofish_generic twofish_x86_64_3way xts lrw gf128mul glue_helper twofish_x86_64 twofish_common blowfish_generic blowfish_x86_64 blowfish_common des_generic cbc xcbc rmd160 sha512_generic hmac crypto_null af_key xfrm_algo 8021q garp bridge stp llc tun atmtcp clip atm ext3 mbcache jbd iTCO_wdt coretemp kvm_intel iTCO_vendor_support kvm pcspkr evdev ehci_pci lpc_ich mfd_core i5400_edac edac_core i5k_amb shpchp button processor thermal_sys xfs crc32c_generic libcrc32c dm_mod usbhid sg hid sr_mod sd_mod cdrom crc_t10dif crct10dif_common ata_generic ahci ata_piix tg3 libahci libata uhci_hcd ptp ehci_hcd pps_core usbcore scsi_mod libphy usb_common [last unloaded: l2tp_core] [ 1937.664005] CPU: 0 PID: 10022 Comm: l2tpstress Tainted: G O 3.17.0-rc1 #1 [ 1937.664005] Hardware name: HP ProLiant DL160 G5, BIOS O12 08/22/2008 [ 1937.664005] task: ffff8800d8fda790 ti: ffff8800c43c4000 task.ti: ffff8800c43c4000 [ 1937.664005] RIP: 0010:[<ffffffffa049db88>] [<ffffffffa049db88>] pppol2tp_connect+0x33d/0x41e [l2tp_ppp] [ 1937.664005] RSP: 0018:ffff8800c43c7de8 EFLAGS: 00010282 [ 1937.664005] RAX: ffff8800da8a7240 RBX: ffff8800d8c64600 RCX: 000001c325a137b5 [ 1937.664005] RDX: 8c6318c6318c6320 RSI: 000000000000010c RDI: 0000000000000000 [ 1937.664005] RBP: ffff8800c43c7ea8 R08: 0000000000000000 R09: 0000000000000000 [ 1937.664005] R10: ffffffffa048e2c0 R11: ffff8800d8c64600 R12: ffff8800ca7a5000 [ 1937.664005] R13: ffff8800c439bf40 R14: 000000000000000c R15: 0000000000000009 [ 1937.664005] FS: 00007fd7f610f700(0000) GS:ffff88011a600000(0000) knlGS:0000000000000000 [ 1937.664005] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b [ 1937.664005] CR2: 0000000000000020 CR3: 00000000d9d75000 CR4: 00000000000027e0 [ 1937.664005] Stack: [ 1937.664005] ffffffffa049da80 ffff8800d8fda790 000000000000005b ffff880000000009 [ 1937.664005] ffff8800daf3f200 0000000000000003 ffff8800c43c7e48 ffffffff81109b57 [ 1937.664005] ffffffff81109b0e ffffffff8114c566 0000000000000000 0000000000000000 [ 1937.664005] Call Trace: [ 1937.664005] [<ffffffffa049da80>] ? pppol2tp_connect+0x235/0x41e [l2tp_ppp] [ 1937.664005] [<ffffffff81109b57>] ? might_fault+0x9e/0xa5 [ 1937.664005] [<ffffffff81109b0e>] ? might_fault+0x55/0xa5 [ 1937.664005] [<ffffffff8114c566>] ? rcu_read_unlock+0x1c/0x26 [ 1937.664005] [<ffffffff81309196>] SYSC_connect+0x87/0xb1 [ 1937.664005] [<ffffffff813e56f7>] ? sysret_check+0x1b/0x56 [ 1937.664005] [<ffffffff8107590d>] ? trace_hardirqs_on_caller+0x145/0x1a1 [ 1937.664005] [<ffffffff81213dee>] ? trace_hardirqs_on_thunk+0x3a/0x3f [ 1937.664005] [<ffffffff8114c262>] ? spin_lock+0x9/0xb [ 1937.664005] [<ffffffff813092b4>] SyS_connect+0x9/0xb [ 1937.664005] [<ffffffff813e56d2>] system_call_fastpath+0x16/0x1b [ 1937.664005] Code: 10 2a 84 81 e8 65 76 bd e0 65 ff 0c 25 10 bb 00 00 4d 85 ed 74 37 48 8b 85 60 ff ff ff 48 8b 80 88 01 00 00 48 8b b8 10 02 00 00 <48> 8b 47 20 ff 50 20 85 c0 74 0f 83 e8 28 89 83 10 01 00 00 89 [ 1937.664005] RIP [<ffffffffa049db88>] pppol2tp_connect+0x33d/0x41e [l2tp_ppp] [ 1937.664005] RSP <ffff8800c43c7de8> [ 1937.664005] CR2: 0000000000000020 [ 1939.559375] ---[ end trace 82d44500f28f8708 ]--- Fixes: f34c4a35 ("l2tp: take PMTU from tunnel UDP socket") Signed-off-by:
Guillaume Nault <g.nault@alphalink.fr> Acked-by:
-
Gerhard Stenzel authored
[ Upstream commit a45e92a5 ] The first initializer in the following union vxlan_addr ipa = { .sin.sin_addr.s_addr = tip, .sa.sa_family = AF_INET, }; is optimised away by the compiler, due to the second initializer, therefore initialising .sin.sin_addr.s_addr always to 0. This results in netlink messages indicating a L3 miss never contain the missed IP address. This was observed with GCC 4.8 and 4.9. I do not know about previous versions. The problem affects user space programs relying on an IP address being sent as part of a netlink message indicating a L3 miss. Changing .sa.sa_family = AF_INET, to .sin.sin_family = AF_INET, fixes the problem. Signed-off-by:
Gerhard Stenzel <gerhard.stenzel@de.ibm.com> Signed-off-by:
-
Jiri Benc authored
[ Upstream commit 2ba5af42 ] When there are multiple vlan headers present in a received frame, the first one is put into vlan_tci and protocol is set to ETH_P_8021Q. Anything in the skb beyond the VLAN TPID may be still non-linear, including the inner TCI and ethertype. While ovs_flow_extract takes care of IP and IPv6 headers, it does nothing with ETH_P_8021Q. Later, if OVS_ACTION_ATTR_POP_VLAN is executed, __pop_vlan_tci pulls the next vlan header into vlan_tci. This leads to two things: 1. Part of the resulting ethernet header is in the non-linear part of the skb. When eth_type_trans is called later as the result of OVS_ACTION_ATTR_OUTPUT, kernel BUGs in __skb_pull. Also, __pop_vlan_tci is in fact accessing random data when it reads past the TPID. 2. network_header points into the ethernet header instead of behind it. mac_len is set to a wrong value (10), too. Reported-by:
Yulong Pei <ypei@redhat.com> Signed-off-by:
Jiri Benc <jbenc@redhat.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit dc808110 ] af_packet can currently overwrite kernel memory by out of bound accesses, because it assumed a [new] block can always hold one frame. This is not generally the case, even if most existing tools do it right. This patch clamps too long frames as API permits, and issue a one time error on syslog. [ 394.357639] tpacket_rcv: packet too big, clamped from 5042 to 3966. macoff=82 In this example, packet header tp_snaplen was set to 3966, and tp_len was set to 5042 (skb->len) Signed-off-by:
Daniel Borkmann <dborkman@redhat.com> Acked-by:
Neil Horman <nhorman@tuxdriver.com> Signed-off-by:
-
Neal Cardwell authored
[ Upstream commit 0c9ab092 ] Fix TCP FRTO logic so that it always notices when snd_una advances, indicating that any RTO after that point will be a new and distinct loss episode. Previously there was a very specific sequence that could cause FRTO to fail to notice a new loss episode had started: (1) RTO timer fires, enter FRTO and retransmit packet 1 in write queue (2) receiver ACKs packet 1 (3) FRTO sends 2 more packets (4) RTO timer fires again (should start a new loss episode) The problem was in step (3) above, where tcp_process_loss() returned early (in the spot marked "Step 2.b"), so that it never got to the logic to clear icsk_retransmits. Thus icsk_retransmits stayed non-zero. Thus in step (4) tcp_enter_loss() would see the non-zero icsk_retransmits, decide that this RTO is not a new episode, and decide not to cut ssthresh and remember the current cwnd and ssthresh for undo. There were two main consequences to the bug that we have observed. First, ssthresh was not decreased in step (4). Second, when there was a series of such FRTO (1-4) sequences that happened to be followed by an FRTO undo, we would restore the cwnd and ssthresh from before the entire series started (instead of the cwnd and ssthresh from before the most recent RTO). This could result in cwnd and ssthresh being restored to values much bigger than the proper values. Signed-off-by:
Yuchung Cheng <ycheng@google.com> Fixes: e33099f9 ("tcp: implement RFC5682 F-RTO") Signed-off-by:
-
Neal Cardwell authored
[ Upstream commit 4fab9071 ] Make sure we use the correct address-family-specific function for handling MTU reductions from within tcp_release_cb(). Previously AF_INET6 sockets were incorrectly always using the IPv6 code path when sometimes they were handling IPv4 traffic and thus had an IPv4 dst. Signed-off-by:
Willem de Bruijn <willemb@google.com> Fixes: 563d34d0 ("tcp: dont drop MTU reduction indications") Reviewed-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
-
Shmulik Ladkani authored
[ Upstream commit bc8fc7b8 ] As of 4fddbf5d ("sit: strictly restrict incoming traffic to tunnel link device"), when looking up a tunnel, tunnel's underlying interface (t->parms.link) is verified to match incoming traffic's ingress device. However the comparison was incorrectly based on skb->dev->iflink. Instead, dev->ifindex should be used, which correctly represents the interface from which the IP stack hands the ipip6 packets. This allows setting up sit tunnels bound to vlan interfaces (otherwise incoming ipip6 traffic on the vlan interface was dropped due to ipip6_tunnel_lookup match failure). Signed-off-by:
Shmulik Ladkani <shmulik.ladkani@gmail.com> Acked-by:
-
Stanislaw Gruszka authored
[ Upstream commit 10545937 ] On IOMMU systems DMA mapping can fail, we need to check for that possibility. Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
-
Vlad Yasevich authored
[ Upstream commit 0d5501c1 ] Currently the functionality to untag traffic on input resides as part of the vlan module and is build only when VLAN support is enabled in the kernel. When VLAN is disabled, the function vlan_untag() turns into a stub and doesn't really untag the packets. This seems to create an interesting interaction between VMs supporting checksum offloading and some network drivers. There are some drivers that do not allow the user to change tx-vlan-offload feature of the driver. These drivers also seem to assume that any VLAN-tagged traffic they transmit will have the vlan information in the vlan_tci and not in the vlan header already in the skb. When transmitting skbs that already have tagged data with partial checksum set, the checksum doesn't appear to be updated correctly by the card thus resulting in a failure to establish TCP connections. The following is a packet trace taken on the receiver where a sender is a VM with a VLAN configued. The host VM is running on doest not have VLAN support and the outging interface on the host is tg3: 10:12:43.503055 52:54:00:ae:42:3f > 28:d2:44:7d:c2:de, ethertype 802.1Q (0x8100), length 78: vlan 100, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 27243, offset 0, flags [DF], proto TCP (6), length 60) 10.0.100.1.58545 > 10.0.100.10.ircu-2: Flags [S], cksum 0xdc39 (incorrect -> 0x48d9), seq 1069378582, win 29200, options [mss 1460,sackOK,TS val 4294837885 ecr 0,nop,wscale 7], length 0 10:12:44.505556 52:54:00:ae:42:3f > 28:d2:44:7d:c2:de, ethertype 802.1Q (0x8100), length 78: vlan 100, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 27244, offset 0, flags [DF], proto TCP (6), length 60) 10.0.100.1.58545 > 10.0.100.10.ircu-2: Flags [S], cksum 0xdc39 (incorrect -> 0x44ee), seq 1069378582, win 29200, options [mss 1460,sackOK,TS val 4294838888 ecr 0,nop,wscale 7], length 0 This connection finally times out. I've only access to the TG3 hardware in this configuration thus have only tested this with TG3 driver. There are a lot of other drivers that do not permit user changes to vlan acceleration features, and I don't know if they all suffere from a similar issue. The patch attempt to fix this another way. It moves the vlan header stipping code out of the vlan module and always builds it into the kernel network core. This way, even if vlan is not supported on a virtualizatoin host, the virtual machines running on top of such host will still work with VLANs enabled. CC: Patrick McHardy <kaber@trash.net> CC: Nithin Nayak Sujir <nsujir@broadcom.com> CC: Michael Chan <mchan@broadcom.com> CC: Jiri Pirko <jiri@resnulli.us> Signed-off-by:
-
Jiri Benc authored
[ Upstream commit 945a3676 ] Commit 1d8faf48 ("net/core: Add VF link state control") added new attribute to IFLA_VF_INFO group in rtnl_fill_ifinfo but did not adjust size of the allocated memory in if_nlmsg_size/rtnl_vfinfo_size. As the result, we may trigger warnings in rtnl_getlink and similar functions when many VF links are enabled, as the information does not fit into the allocated skb. Fixes: 1d8faf48 ("net/core: Add VF link state control") Reported-by:
-
Daniel Borkmann authored
[ Upstream commit 4e48ed88 ] netlink doesn't set any network header offset thus when the skb is being passed to tap devices via dev_queue_xmit_nit(), it emits klog false positives due to it being unset like: ... [ 124.990397] protocol 0000 is buggy, dev nlmon0 [ 124.990411] protocol 0000 is buggy, dev nlmon0 ... So just reset the network header before passing to the device; for packet sockets that just means nothing will change - mac and net offset hold the same value just as before. Reported-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
David Jeffery authored
commit 92a56555 upstream. If a SIGKILL is sent to a task waiting in __nfs_iocounter_wait, it will busy-wait or soft lockup in its while loop. nfs_wait_bit_killable won't sleep, and the loop won't exit on the error return. Stop the busy-wait by breaking out of the loop when nfs_wait_bit_killable returns an error. Signed-off-by:
David Jeffery <djeffery@redhat.com> Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Cc: Neil Brown <nfbrown@suse.com> Signed-off-by:
-
- 13 Oct, 2014 6 commits
-
-
Lars Ellenberg authored
commit bbc1c5e8 upstream. Since linux kernel 3.13, kthread_run() internally uses wait_for_completion_killable(). We sometimes may use kthread_run() while we still have a signal pending, which we used to kick our threads out of potentially blocking network functions, causing kthread_run() to mistake that as a new fatal signal and fail. Fix: flush_signals() before kthread_run(). Signed-off-by:
Philipp Reisner <philipp.reisner@linbit.com> Signed-off-by:
Lars Ellenberg <lars.ellenberg@linbit.com> Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Andrew Hunter authored
commit d78c9300 upstream. timeval_to_jiffies tried to round a timeval up to an integral number of jiffies, but the logic for doing so was incorrect: intervals corresponding to exactly N jiffies would become N+1. This manifested itself particularly repeatedly stopping/starting an itimer: setitimer(ITIMER_PROF, &val, NULL); setitimer(ITIMER_PROF, NULL, &val); would add a full tick to val, _even if it was exactly representable in terms of jiffies_ (say, the result of a previous rounding.) Doing this repeatedly would cause unbounded growth in val. So fix the math. Here's what was wrong with the conversion: we essentially computed (eliding seconds) jiffies = usec * (NSEC_PER_USEC/TICK_NSEC) by using scaling arithmetic, which took the best approximation of NSEC_PER_USEC/TICK_NSEC with denominator of 2^USEC_JIFFIE_SC = x/(2^USEC_JIFFIE_SC), and computed: jiffies = (usec * x) >> USEC_JIFFIE_SC and rounded this calculation up in the intermediate form (since we can't necessarily exactly represent TICK_NSEC in usec.) But the scaling arithmetic is a (very slight) *over*approximation of the true value; that is, instead of dividing by (1 usec/ 1 jiffie), we effectively divided by (1 usec/1 jiffie)-epsilon (rounding down). This would normally be fine, but we want to round timeouts up, and we did so by adding 2^USEC_JIFFIE_SC - 1 before the shift; this would be fine if our division was exact, but dividing this by the slightly smaller factor was equivalent to adding just _over_ 1 to the final result (instead of just _under_ 1, as desired.) In particular, with HZ=1000, we consistently computed that 10000 usec was 11 jiffies; the same was true for any exact multiple of TICK_NSEC. We could possibly still round in the intermediate form, adding something less than 2^USEC_JIFFIE_SC - 1, but easier still is to convert usec->nsec, round in nanoseconds, and then convert using time*spec*_to_jiffies. This adds one constant multiplication, and is not observably slower in microbenchmarks on recent x86 hardware. Tested: the following program: int main() { struct itimerval zero = {{0, 0}, {0, 0}}; /* Initially set to 10 ms. */ struct itimerval initial = zero; initial.it_interval.tv_usec = 10000; setitimer(ITIMER_PROF, &initial, NULL); /* Save and restore several times. */ for (size_t i = 0; i < 10; ++i) { struct itimerval prev; setitimer(ITIMER_PROF, &zero, &prev); /* on old kernels, this goes up by TICK_USEC every iteration */ printf("previous value: %ld %ld %ld %ld\n", prev.it_interval.tv_sec, prev.it_interval.tv_usec, prev.it_value.tv_sec, prev.it_value.tv_usec); setitimer(ITIMER_PROF, &prev, NULL); } return 0; } Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Paul Turner <pjt@google.com> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Prarit Bhargava <prarit@redhat.com> Reviewed-by:
Paul Turner <pjt@google.com> Reported-by:
Aaron Jacobs <jacobsa@google.com> Signed-off-by:
Andrew Hunter <ahh@google.com> [jstultz: Tweaked to apply to 3.17-rc] Signed-off-by:
John Stultz <john.stultz@linaro.org> [bwh: Backported to 3.16: adjust filename] Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Hans Verkuil authored
commit 58d75f4b upstream. The recent conversion of saa7134 to vb2 unconvered a poll() bug that broke the teletext applications alevt and mtt. These applications expect that calling poll() without having called VIDIOC_STREAMON will cause poll() to return POLLERR. That did not happen in vb2. This patch fixes that behavior. It also fixes what should happen when poll() is called when STREAMON is called but no buffers have been queued. In that case poll() will also return POLLERR, but only for capture queues since output queues will always return POLLOUT anyway in that situation. This brings the vb2 behavior in line with the old videobuf behavior. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Acked-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
-
Mel Gorman authored
commit abc40bd2 upstream. This patch reverts 1ba6e0b5 ("mm: numa: split_huge_page: transfer the NUMA type from the pmd to the pte"). If a huge page is being split due a protection change and the tail will be in a PROT_NONE vma then NUMA hinting PTEs are temporarily created in the protected VMA. VM_RW|VM_PROTNONE |-----------------| ^ split here In the specific case above, it should get fixed up by change_pte_range() but there is a window of opportunity for weirdness to happen. Similarly, if a huge page is shrunk and split during a protection update but before pmd_numa is cleared then a pte_numa can be left behind. Instead of adding complexity trying to deal with the case, this patch will not mark PTEs NUMA when splitting a huge page. NUMA hinting faults will not be triggered which is marginal in comparison to the complexity in dealing with the corner cases during THP split. Signed-off-by:
Mel Gorman <mgorman@suse.de> Acked-by:
Rik van Riel <riel@redhat.com> Acked-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Waiman Long authored
commit f8303c25 upstream. In __split_huge_page_map(), the check for page_mapcount(page) is invariant within the for loop. Because of the fact that the macro is implemented using atomic_read(), the redundant check cannot be optimized away by the compiler leading to unnecessary read to the page structure. This patch moves the invariant bug check out of the loop so that it will be done only once. On a 3.16-rc1 based kernel, the execution time of a microbenchmark that broke up 1000 transparent huge pages using munmap() had an execution time of 38,245us and 38,548us with and without the patch respectively. The performance gain is about 1%. Signed-off-by:
Waiman Long <Waiman.Long@hp.com> Acked-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Pavel Shilovsky authored
commit 52755808 upstream. SMB2 servers indicates the end of a directory search with STATUS_NO_MORE_FILE error code that is not processed now. This causes generic/257 xfstest to fail. Fix this by triggering the end of search by this error code in SMB2_query_directory. Also when negotiating CIFS protocol we tell the server to close the search automatically at the end and there is no need to do it itself. In the case of SMB2 protocol, we need to close it explicitly - separate close directory checks for different protocols. Signed-off-by:
Pavel Shilovsky <pshilovsky@samba.org> Signed-off-by:
Steve French <smfrench@gmail.com> Signed-off-by:
-
