Prepare input updates for 6.8 merge window.

Adds a driver for a mini gamepad that communicates over i2c, the gamepad
has bidirectional thumb stick input and six buttons.

The gamepad chip utilizes the open framework from Adafruit called 'Seesaw'
to transmit the ADC data for the joystick and digital pin state for the
buttons. I have only implemented the functionality required to receive the
thumb stick and button state.

Steps in reading the gamepad state over i2c:
  1. Reset the registers
  2. Set the pin mode of the pins specified by the `BUTTON_MASK` to input
      `BUTTON_MASK`: A bit-map for the six digital pins internally
       connected to the joystick buttons.
  3. Enable internal pullup resistors for the `BUTTON_MASK`
  4. Bulk set the pin state HIGH for `BUTTON_MASK`
  5. Poll the device for button and joystick state done by:
      `seesaw_read_data(struct i2c_client *client, struct seesaw_data *data)`

Product page:
  https://www.adafruit.com/product/5743
Arduino driver:
  https://github.com/adafruit/Adafruit_Seesaw

Driver tested on RPi Zero 2W
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Anshul Dalal <anshulusr@gmail.com>
Link: https://lore.kernel.org/r/20240106015111.882325-2-anshulusr@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Adds bindings for the Adafruit Seesaw Gamepad.

The gamepad functions as an i2c device with the default address of 0x50
and has an IRQ pin that can be enabled in the driver to allow for a rising
edge trigger on each button press or joystick movement.

Product page:
  https://www.adafruit.com/product/5743
Arduino driver:
  https://github.com/adafruit/Adafruit_SeesawReviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Anshul Dalal <anshulusr@gmail.com>
Link: https://lore.kernel.org/r/20240106015111.882325-1-anshulusr@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

devm_input_allocate_device() already sets parent of the new input
device, there's no need to set it up explicitly.
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/ZYOseYfVgg0Ve6Zl@google.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

There is nothing OF-specific in the driver, so switch from OF properties
helpers to generic device helpers.
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/ZYOsUfKceOFXuCt5@google.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This patch adds support for each available OTP variant of the device.
The OTP configuration cannot be read over I2C, so it is derived from
a compatible string instead.

Early revisions of the D0 order code require their OTP-enabled func-
tionality to be manually restored following a soft reset; this patch
accommodates this erratum as well.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/ZZMaZbdk6iAKUjlm@nixie71Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This patch adds bindings for the D0 order code of the device. This
order code represents an OTP variant that enables a touch-and-hold
function in place of slider 1.

Also included is the ability to specify the 00 order code (default
option with no OTP customization) explicitly.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/ZZMaW9RkQ9bKXOUn@nixie71Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This patch adds support for slider gestures that can be expressed
by the device. Each gesture (e.g. tap or hold) can be mapped to a
unique keycode for either slider 0 or 1.

With this change, raw slider coordinates are reported only if the
slider has no keycodes defined. This prevents unwanted mouse cur-
sor movement when expressing axial gestures (e.g. swipe) and also
eliminates some unnecessary I2C traffic.

Different revisions of silicon use different tap and swipe timeout
step sizes. Apply an appropriate scaling factor depending on which
revision is found.

To facilitate this change, store the iqs269_ver_info struct in the
driver's private data so that other functions can use it after the
driver has probed.

Last but not least, a former reserved field in iqs269_ver_info now
contains useful information; give it a name (fw_num).
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/ZZMaT46WQq1/Nrsb@nixie71Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This patch adds bindings for slider gestures that can be expressed
by the device.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/ZZMaPrbSi4IrzwKF@nixie71Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

commit ae42f928 ("gpio: Return EPROBE_DEFER if gc->to_irq is NULL")
make gpiod_to_irq() possible to return -EPROBE_DEFER when the racing
happens. This causes the following error message to be printed:

    gpio-keys gpio_keys: Unable to get irq number for GPIO 0, error -517

Fix that by changing dev_err() to dev_err_probe()
Signed-off-by: Hermes Zhang <chenhuiz@axis.com>
Link: https://lore.kernel.org/r/20231229013657.692600-1-Hermes.Zhang@axis.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Only driver-specific properties were accepted, change it
to use the now-available standard properties.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20231223221213.774868-4-andreas@kemnade.infoSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Enable touchscreen orientation to be specified by using standard
properties.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231223221213.774868-3-andreas@kemnade.infoSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Convert Neonode infrared touchscreen controller binding to DT schema.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231223221213.774868-2-andreas@kemnade.infoSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This add a mapping for the airplane mode button on the TUXEDO Pulse Gen3.

While it is physically a key it behaves more like a switch, sending a key
down on first press and a key up on 2nd press. Therefor the switch event
is used here. Besides this behaviour it uses the HID usage-id 0xc6
(Wireless Radio Button) and not 0xc8 (Wireless Radio Slider Switch), but
since neither 0xc6 nor 0xc8 are currently implemented at all in
soc_button_array this not to standard behaviour is not put behind a quirk
for the moment.
Signed-off-by: Christoffer Sandberg <cs@tuxedo.de>
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Link: https://lore.kernel.org/r/20231215171718.80229-1-wse@tuxedocomputers.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Convert devicetree binding documentation for ti drv2665 and drv2667
haptics driver to json-schema. The previously two separate bindings have
been merged into a single drv266x.yaml.
Signed-off-by: Anshul Dalal <anshulusr@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231221183109.684325-1-anshulusr@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Replace dev_err()->dev_err_probe() to simplify probe().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20231213214803.9931-4-biju.das.jz@bp.renesas.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The memory allocation core code already prints error message in case of
OOM. So, drop additional print messages for OOM cases.

While at it, input_register_device() is already printing error messages on
failure. Drop the redundant print.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20231213214803.9931-3-biju.das.jz@bp.renesas.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Simplify probe() by replacing of_match_node() for retrieving match data by
device_get_match_data().

Some minor cleanups:
 * Remove the trailing comma in the terminator entry for the OF
   table making code robust against (theoretical) misrebases or other
   similar things where the new entry goes _after_ the termination without
   the compiler noticing.
 * Move OF table near to the user.
 * Arrange variables in reverse xmas tree order in probe().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20231213214803.9931-2-biju.das.jz@bp.renesas.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This driver does not have any in-tree users but is passing a
legacy GPIO number through platform data.

Convert it to use a GPIO descriptor, new users or outoftree
users can easily be implemented using GPIO descriptor tables
or software nodes.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231129-descriptors-input-v1-4-9433162914a3@linaro.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The driver supports passing some GPIO lines for rows and columns
through the driver data, but there is no in-kernel user of this.

Further the use seems convoluted because the GPIO lines are unused
in the driver, then explicitly free:ed when removing it without
being requested when probing it, which is assymetric and just
a recepie for disaster.

Remove the support for these unused GPIOs, if need be support can
be reestablished in an organized fashion using GPIO descriptors.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20231129-descriptors-input-v1-3-9433162914a3@linaro.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The TCA6416 keypad driver is including the legacy GPIO
header <linux/gpio.h> for no reason, it is not using any
of its symbols. Drop the header.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231129-descriptors-input-v1-2-9433162914a3@linaro.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The Navpoint driver uses a GPIO line, convert this to use
a GPIO descriptor. There are no in-kernel users but out of tree
users can easily be added or converted using a GPIO descriptor
table as with numerous other drivers.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231129-descriptors-input-v1-1-9433162914a3@linaro.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Follow the advice of the Documentation/filesystems/sysfs.rst and show()
should only use sysfs_emit() or sysfs_emit_at() when formatting the
value to be returned to user space.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/202212071644171074630@zte.com.cnSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Replace calls to scnprintf() in the methods showing device attributes
with sysfs_emit() to simplify the code.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/202212011548387254492@zte.com.cnSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Replace calls to scnprintf() in the methods showing device attributes
with sysfs_emit() to simplify the code.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/202212011548387254492@zte.com.cnSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Replace calls to scnprintf() in the methods showing device attributes
with sysfs_emit() to simplify the code.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/202212011551429834598@zte.com.cnSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Follow the advice of the Documentation/filesystems/sysfs.rst and show()
should only use sysfs_emit() or sysfs_emit_at() when formatting the
value to be returned to user space.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Oliver Graute <oliver.graute@kococonnector.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Replace the calls to various *printf() functions with sysfs_emit() to
simplify the code.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/202212021453578171100@zte.com.cnSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Replace calls to scnprintf() in the methods showing device attributes
with sysfs_emit() to simplify the code.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/202212021133398847947@zte.com.cnSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add the needed device-tree compatible strings to the MAX77693 haptic
driver, so it can be automatically loaded when compiled as a kernel
module and given device-tree contains separate (i.e. 'motor-driver') node
under the main PMIC node. When device is instantiated from device-tree,
the driver data cannot be read via platform_get_device_id(), so get
device type from the parent MFD device instead, what works for both
cases.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231006100320.2908210-1-m.szyprowski@samsung.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20231001-input-maple-v1-3-ed3716051431@kernel.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20231001-input-maple-v1-2-ed3716051431@kernel.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The cap11xx devices have three hardware identification registers which are
currently marked as volatile, preventing caching of those registers. This
is not ideal since the registers should never change at runtime, we should
be able to cache the value after the first read. Stop marking the registers
as volatile, we don't have register defaults specified in the driver so
this will result in reading from the hardware on first use.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20231001-input-maple-v1-1-ed3716051431@kernel.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add the VID and PID of Razer Wolverine V2 to xpad_device.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Link: https://lore.kernel.org/r/20231125-razer-wolverine-v2-v1-1-979fe9f9288e@z3ntu.xyzSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add support for advanced sensitivity settings that allows more precise
tunig of touch buttons. Input-treshold allows to set the sensitivity for
each channel separately. Also add signal guard feature for CAP129x chips.
Signed-off-by: Jiri Valek - 2N <jiriv@axis.com>
Link: https://lore.kernel.org/r/20231121155250.613242-3-jiriv@axis.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add support for advanced sensitivity settings and signal guard feature.
Signed-off-by: Jiri Valek - 2N <jiriv@axis.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231121155250.613242-2-jiriv@axis.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

ida_alloc() and ida_free() should be preferred to the deprecated
ida_simple_get() and ida_simple_remove().

This is less verbose.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/a3e30e30f18cc5d6f032c8013ce9d900c8e223e5.1702228806.git.christophe.jaillet@wanadoo.frSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

According to SWPU235AB, table 26-6, fclk is required to generate events
at least on OMAP4460, so keep fclk enabled all the time the device
is opened.
Suggested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20231211221757.517427-1-andreas@kemnade.infoSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use the guard(mutex) macro for handle mutex lock/unlocks.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Link: https://lore.kernel.org/r/20231202-pxrc-guard-v3-1-2ca8bc8cf689@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Convert device tree binding documentation for GPIO attached mouse to
json-schema.
Signed-off-by: Anshul Dalal <anshulusr@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231208075037.114598-1-anshulusr@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>