- 22 Aug, 2016 40 commits
-
-
Rafael J. Wysocki authored
commit 65c0554b upstream. Logan Gunthorpe reports that hibernation stopped working reliably for him after commit ab76f7b4 (x86/mm: Set NX on gap between __ex_table and rodata). That turns out to be a consequence of a long-standing issue with the 64-bit image restoration code on x86, which is that the temporary page tables set up by it to avoid page tables corruption when the last bits of the image kernel's memory contents are copied into their original page frames re-use the boot kernel's text mapping, but that mapping may very well get corrupted just like any other part of the page tables. Of course, if that happens, the final jump to the image kernel's entry point will go to nowhere. The exact reason why commit ab76f7b4 matters here is that it sometimes causes a PMD of a large page to be split into PTEs that are allocated dynamically and get corrupted during image restoration as described above. To fix that issue note that the code copying the last bits of the image kernel's memory contents to the page frames occupied by them previoulsy doesn't use the kernel text mapping, because it runs from a special page covered by the identity mapping set up for that code from scratch. Hence, the kernel text mapping is only needed before that code starts to run and then it will only be used just for the final jump to the image kernel's entry point. Accordingly, the temporary page tables set up in swsusp_arch_resume() on x86-64 need to contain the kernel text mapping too. That mapping is only going to be used for the final jump to the image kernel, so it only needs to cover the image kernel's entry point, because the first thing the image kernel does after getting control back is to switch over to its own original page tables. Moreover, the virtual address of the image kernel's entry point in that mapping has to be the same as the one mapped by the image kernel's page tables. With that in mind, modify the x86-64's arch_hibernation_header_save() and arch_hibernation_header_restore() routines to pass the physical address of the image kernel's entry point (in addition to its virtual address) to the boot kernel (a small piece of assembly code involved in passing the entry point's virtual address to the image kernel is not necessary any more after that, so drop it). Update RESTORE_MAGIC too to reflect the image header format change. Next, in set_up_temporary_mappings(), use the physical and virtual addresses of the image kernel's entry point passed in the image header to set up a minimum kernel text mapping (using memory pages that won't be overwritten by the image kernel's memory contents) that will map those addresses to each other as appropriate. This makes the concern about the possible corruption of the original boot kernel text mapping go away and if the the minimum kernel text mapping used for the final jump marks the image kernel's entry point memory as executable, the jump to it is guaraneed to succeed. Fixes: ab76f7b4 (x86/mm: Set NX on gap between __ex_table and rodata) Link: http://marc.info/?l=linux-pm&m=146372852823760&w=2Reported-by:
Logan Gunthorpe <logang@deltatee.com> Reported-and-tested-by:
Borislav Petkov <bp@suse.de> Tested-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> [bwh: Backported to 3.16: adjust context] Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
Takashi Iwai authored
commit 62db7152 upstream. vortex_wtdma_bufshift() function does calculate the page index wrongly, first masking then shift, which always results in zero. The proper computation is to first shift, then mask. Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Dan Carpenter authored
commit 5b4d10f5 upstream. There is a static checker warning here "warn: mask and shift to zero" and the code sets "ring" to zero every time. From looking at how QLCNIC_FETCH_RING_ID() is used in qlcnic_83xx_process_rcv_ring() the qlcnic_83xx_hndl() should be removed. Fixes: 4be41e92 ('qlcnic: 83xx data path routines') Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Sven Eckelmann authored
commit 420cb1b7 upstream. The untagged vlan object is only destroyed when the interface is removed via the legacy sysfs interface. But it also has to be destroyed when the standard rtnl-link interface is used. Fixes: 5d2c05b2 ("batman-adv: add per VLAN interface attribute framework") Signed-off-by:
Sven Eckelmann <sven@narfation.org> Acked-by:
Antonio Quartulli <a@unstable.cc> Signed-off-by:
Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by:
-
Sven Eckelmann authored
commit 3b55e442 upstream. The skb_linearize may reallocate the skb. This makes the calculated pointer for ethhdr invalid. But it the pointer is used later to fill in the RR field of the batadv_icmp_packet_rr packet. Instead re-evaluate eth_hdr after the skb_linearize+skb_cow to fix the pointer and avoid the invalid read. Fixes: da6b8c20 ("batman-adv: generalize batman-adv icmp packet handling") Signed-off-by:
-
Ben Hutchings authored
commit baceced9 upstream. Each batadv_tt_local_entry hold a single reference to a batadv_softif_vlan. In case a new entry cannot be added to the hash table, the error path puts the reference, but the reference will also now be dropped by batadv_tt_local_entry_release(). Fixes: a33d970d ("batman-adv: Fix reference counting of vlan object for tt_local_entry") Signed-off-by:
-
Sven Eckelmann authored
commit 9c4604a2 upstream. The tt_req_node is added and removed from a list inside a spinlock. But the locking is sometimes removed even when the object is still referenced and will be used later via this reference. For example batadv_send_tt_request can create a new tt_req_node (including add to a list) and later re-acquires the lock to remove it from the list and to free it. But at this time another context could have already removed this tt_req_node from the list and freed it. CPU#0 batadv_batman_skb_recv from net_device 0 -> batadv_iv_ogm_receive -> batadv_iv_ogm_process -> batadv_iv_ogm_process_per_outif -> batadv_tvlv_ogm_receive -> batadv_tvlv_ogm_receive -> batadv_tvlv_containers_process -> batadv_tvlv_call_handler -> batadv_tt_tvlv_ogm_handler_v1 -> batadv_tt_update_orig -> batadv_send_tt_request -> batadv_tt_req_node_new spin_lock(...) allocates new tt_req_node and adds it to list spin_unlock(...) return tt_req_node CPU#1 batadv_batman_skb_recv from net_device 1 -> batadv_recv_unicast_tvlv -> batadv_tvlv_containers_process -> batadv_tvlv_call_handler -> batadv_tt_tvlv_unicast_handler_v1 -> batadv_handle_tt_response spin_lock(...) tt_req_node gets removed from list and is freed spin_unlock(...) CPU#0 <- returned to batadv_send_tt_request spin_lock(...) tt_req_node gets removed from list and is freed MEMORY CORRUPTION/SEGFAULT/... spin_unlock(...) This can only be solved via reference counting to allow multiple contexts to handle the list manipulation while making sure that only the last context holding a reference will free the object. Fixes: a73105b8 ("batman-adv: improved client announcement mechanism") Signed-off-by:
Martin Weinelt <martin@darmstadt.freifunk.net> Tested-by:
Amadeus Alfa <amadeus@chemnitz.freifunk.net> Signed-off-by:
-
Simon Wunderlich authored
commit 0b3dd7df upstream. If a VLAN tagged frame is received and the corresponding VLAN is not configured on the soft interface, it will splat a WARN on every packet received. This is a quite annoying behaviour for some scenarios, e.g. if bat0 is bridged with eth0, and there are arbitrary VLAN tagged frames from Ethernet coming in without having any VLAN configuration on bat0. The code should probably create vlan objects on the fly and transparently transport these VLAN-tagged Ethernet frames, but until this is done, at least the WARN splat should be replaced by a rate limited output. Fixes: 354136bc ("batman-adv: fix kernel crash due to missing NULL checks") Signed-off-by:
Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by:
-
Sven Eckelmann authored
commit fd7dec25 upstream. The object tt_local is allocated with kmalloc and not initialized when the function batadv_tt_local_add checks for the vlan. But this function can only cleanup the object when the (not yet initialized) reference counter of the object is 1. This is unlikely and thus the object would leak when the vlan could not be found. Instead the uninitialized object tt_local has to be freed manually and the pointer has to set to NULL to avoid calling the function which would try to decrement the reference counter of the not existing object. CID: 1316518 Fixes: 354136bc ("batman-adv: fix kernel crash due to missing NULL checks") Signed-off-by:
-
Florian Fainelli authored
commit 69fc58a5 upstream. If we have a system which uses fixed PHY devices and calls fixed_phy_register() then fixed_phy_unregister() we can exhaust the number of fixed PHYs available after a while, since we keep incrementing the variable phy_fixed_addr, but we never decrement it. This patch fixes that by converting the fixed PHY allocation to using IDA, which takes care of the allocation/dealloaction of the PHY addresses for us. Fixes: a7595121 ("net: phy: extend fixed driver with fixed_phy_register()") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Michael Neuling authored
commit 190ce869 upstream. Currently we have 2 segments that are bolted for the kernel linear mapping (ie 0xc000... addresses). This is 0 to 1TB and also the kernel stacks. Anything accessed outside of these regions may need to be faulted in. (In practice machines with TM always have 1T segments) If a machine has < 2TB of memory we never fault on the kernel linear mapping as these two segments cover all physical memory. If a machine has > 2TB of memory, there may be structures outside of these two segments that need to be faulted in. This faulting can occur when running as a guest as the hypervisor may remove any SLB that's not bolted. When we treclaim and trecheckpoint we have a window where we need to run with the userspace GPRs. This means that we no longer have a valid stack pointer in r1. For this window we therefore clear MSR RI to indicate that any exceptions taken at this point won't be able to be handled. This means that we can't take segment misses in this RI=0 window. In this RI=0 region, we currently access the thread_struct for the process being context switched to or from. This thread_struct access may cause a segment fault since it's not guaranteed to be covered by the two bolted segment entries described above. We've seen this with a crash when running as a guest with > 2TB of memory on PowerVM: Unrecoverable exception 4100 at c00000000004f138 Oops: Unrecoverable exception, sig: 6 [#1] SMP NR_CPUS=2048 NUMA pSeries CPU: 1280 PID: 7755 Comm: kworker/1280:1 Tainted: G X 4.4.13-46-default #1 task: c000189001df4210 ti: c000189001d5c000 task.ti: c000189001d5c000 NIP: c00000000004f138 LR: 0000000010003a24 CTR: 0000000010001b20 REGS: c000189001d5f730 TRAP: 4100 Tainted: G X (4.4.13-46-default) MSR: 8000000100001031 <SF,ME,IR,DR,LE> CR: 24000048 XER: 00000000 CFAR: c00000000004ed18 SOFTE: 0 GPR00: ffffffffc58d7b60 c000189001d5f9b0 00000000100d7d00 000000003a738288 GPR04: 0000000000002781 0000000000000006 0000000000000000 c0000d1f4d889620 GPR08: 000000000000c350 00000000000008ab 00000000000008ab 00000000100d7af0 GPR12: 00000000100d7ae8 00003ffe787e67a0 0000000000000000 0000000000000211 GPR16: 0000000010001b20 0000000000000000 0000000000800000 00003ffe787df110 GPR20: 0000000000000001 00000000100d1e10 0000000000000000 00003ffe787df050 GPR24: 0000000000000003 0000000000010000 0000000000000000 00003fffe79e2e30 GPR28: 00003fffe79e2e68 00000000003d0f00 00003ffe787e67a0 00003ffe787de680 NIP [c00000000004f138] restore_gprs+0xd0/0x16c LR [0000000010003a24] 0x10003a24 Call Trace: [c000189001d5f9b0] [c000189001d5f9f0] 0xc000189001d5f9f0 (unreliable) [c000189001d5fb90] [c00000000001583c] tm_recheckpoint+0x6c/0xa0 [c000189001d5fbd0] [c000000000015c40] __switch_to+0x2c0/0x350 [c000189001d5fc30] [c0000000007e647c] __schedule+0x32c/0x9c0 [c000189001d5fcb0] [c0000000007e6b58] schedule+0x48/0xc0 [c000189001d5fce0] [c0000000000deabc] worker_thread+0x22c/0x5b0 [c000189001d5fd80] [c0000000000e7000] kthread+0x110/0x130 [c000189001d5fe30] [c000000000009538] ret_from_kernel_thread+0x5c/0xa4 Instruction dump: 7cb103a6 7cc0e3a6 7ca222a6 78a58402 38c00800 7cc62838 08860000 7cc000a6 38a00006 78c60022 7cc62838 0b060000 <e8c701a0> 7ccff120 e8270078 e8a70098 ---[ end trace 602126d0a1dedd54 ]--- This fixes this by copying the required data from the thread_struct to the stack before we clear MSR RI. Then once we clear RI, we only access the stack, guaranteeing there's no segment miss. We also tighten the region over which we set RI=0 on the treclaim() path. This may have a slight performance impact since we're adding an mtmsr instruction. Fixes: 090b9284 ("powerpc/tm: Clear MSR RI in non-recoverable TM code") Signed-off-by:
Michael Neuling <mikey@neuling.org> Reviewed-by:
Cyril Bur <cyrilbur@gmail.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Brian King authored
commit 54e430bb upstream. If we fall back to using LSI on the Croc or Crocodile chip we need to clear the interrupt so we don't hang the system. Tested-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
Brian King <brking@linux.vnet.ibm.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Trond Myklebust authored
commit e547f262 upstream. Olga Kornievskaia reports that the following test fails to trigger an OPEN_DOWNGRADE on the wire, and only triggers the final CLOSE. fd0 = open(foo, RDRW) -- should be open on the wire for "both" fd1 = open(foo, RDONLY) -- should be open on the wire for "read" close(fd0) -- should trigger an open_downgrade read(fd1) close(fd1) The issue is that we're missing a check for whether or not the current state transitioned from an O_RDWR state as opposed to having transitioned from a combination of O_RDONLY and O_WRONLY. Reported-by:
Olga Kornievskaia <aglo@umich.edu> Fixes: cd9288ff ("NFSv4: Fix another bug in the close/open_downgrade code") Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by:
Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by:
-
daniel authored
commit 0888d5f3 upstream. The bridge is falsly dropping ipv6 mulitcast packets if there is: 1. No ipv6 address assigned on the brigde. 2. No external mld querier present. 3. The internal querier enabled. When the bridge fails to build mld queries, because it has no ipv6 address, it slilently returns, but keeps the local querier enabled. This specific case causes confusing packet loss. Ipv6 multicast snooping can only work if: a) An external querier is present OR b) The bridge has an ipv6 address an is capable of sending own queries Otherwise it has to forward/flood the ipv6 multicast traffic, because snooping cannot work. This patch fixes the issue by adding a flag to the bridge struct that indicates that there is currently no ipv6 address assinged to the bridge and returns a false state for the local querier in __br_multicast_querier_exists(). Special thanks to Linus Lüssing. Fixes: d1d81d4c ("bridge: check return value of ipv6_dev_get_saddr()") Signed-off-by:
Daniel Danzberger <daniel@dd-wrt.com> Acked-by:
Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by:
-
Jouni Malinen authored
commit 126e7557 upstream. If a user space program (e.g., wpa_supplicant) deletes a STA entry that is currently in NL80211_PLINK_ESTAB state, the number of established plinks counter was not decremented and this could result in rejecting new plink establishment before really hitting the real maximum plink limit. For !user_mpm case, this decrementation is handled by mesh_plink_deactive(). Fix this by decrementing estab_plinks on STA deletion (mesh_sta_cleanup() gets called from there) so that the counter has a correct value and the Beacon frame advertisement in Mesh Configuration element shows the proper value for capability to accept additional peers. Signed-off-by:
Jouni Malinen <j@w1.fi> Signed-off-by:
Johannes Berg <johannes@sipsolutions.net> [bwh: Backported to 3.16: plink_state field is in struct sta_info] Signed-off-by:
-
Florian Fainelli authored
commit 3894396e upstream. bgmac_open() calls phy_start() to initialize the PHY state machine, which will set the interface's carrier state accordingly, no need to force that as this could be conflicting with the PHY state determined by PHYLIB. Fixes: dd4544f0 ("bgmac: driver for GBit MAC core on BCMA bus") Signed-off-by:
-
Florian Fainelli authored
commit c3897f2a upstream. The driver does not start the transmit queue in bgmac_open(). If the queue was stopped prior to closing then re-opening the interface, we would never be able to wake-up again. Fixes: dd4544f0 ("bgmac: driver for GBit MAC core on BCMA bus") Signed-off-by:
-
Martin Schwidefsky authored
commit bcf4dd5f upstream. The test_fp_ctl function is used to test if a given value is a valid floating-point control. The inline assembly in test_fp_ctl uses an incorrect constraint for the 'orig_fpc' variable. If the compiler chooses the same register for 'fpc' and 'orig_fpc' the test_fp_ctl() function always returns true. This allows user space to trigger kernel oopses with invalid floating-point control values on the signal stack. This problem has been introduced with git commit 4725c860 "s390: fix save and restore of the floating-point-control register" Reviewed-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> [bwh: Backported to 3.16: adjust filename] Signed-off-by:
-
Alexey Brodkin authored
commit 9bd54517 upstream. If CONFIG_ARC_DW2_UNWIND is disabled every time arc_unwind_core() gets called following message gets printed in debug console: ----------------->8--------------- CONFIG_ARC_DW2_UNWIND needs to be enabled ----------------->8--------------- That message makes sense if user indeed wants to see a backtrace or get nice function call-graphs in perf but what if user disabled unwinder for the purpose? Why pollute his debug console? So instead we'll warn user about possibly missing feature once and let him decide if that was what he or she really wanted. Signed-off-by:
Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> Signed-off-by:
-
Vineet Gupta authored
commit f52e126c upstream. With recent binutils update to support dwarf CFI pseudo-ops in gas, we now get .eh_frame vs. .debug_frame. Although the call frame info is exactly the same in both, the CIE differs, which the current kernel unwinder can't cope with. This broke both the kernel unwinder as well as loadable modules (latter because of a new unhandled relo R_ARC_32_PCREL from .rela.eh_frame in the module loader) The ideal solution would be to switch unwinder to .eh_frame. For now however we can make do by just ensureing .debug_frame is generated by removing -fasynchronous-unwind-tables .eh_frame generated with -gdwarf-2 -fasynchronous-unwind-tables .debug_frame generated with -gdwarf-2 Fixes STAR 9001058196 Signed-off-by:
-
Christophe JAILLET authored
commit 9c6795a9 upstream. 'commpage_bak' is allocated with 'sizeof(struct echoaudio)' bytes. We then copy 'sizeof(struct comm_page)' bytes in it. On my system, smatch complains because one is 2960 and the other is 3072. This would result in memory corruption or a oops. Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
Alan Stern authored
commit ab2a4bf8 upstream. The USB core contains a bug that can show up when a USB-3 host controller is removed. If the primary (USB-2) hcd structure is released before the shared (USB-3) hcd, the core will try to do a double-free of the common bandwidth_mutex. The problem was described in graphical form by Chung-Geol Kim, who first reported it: ================================================= At *remove USB(3.0) Storage sequence <1> --> <5> ((Problem Case)) ================================================= VOLD ------------------------------------|------------ (uevent) ________|_________ |<1> | |dwc3_otg_sm_work | |usb_put_hcd | |peer_hcd(kref=2)| |__________________| ________|_________ |<2> | |New USB BUS #2 | | | |peer_hcd(kref=1) | | | --(Link)-bandXX_mutex| | |__________________| | ___________________ | |<3> | | |dwc3_otg_sm_work | | |usb_put_hcd | | |primary_hcd(kref=1)| | |___________________| | _________|_________ | |<4> | | |New USB BUS #1 | | |hcd_release | | |primary_hcd(kref=0)| | | | | |bandXX_mutex(free) |<- |___________________| (( VOLD )) ______|___________ |<5> | | SCSI | |usb_put_hcd | |peer_hcd(kref=0) | |*hcd_release | |bandXX_mutex(free*)|<- double free |__________________| ================================================= This happens because hcd_release() frees the bandwidth_mutex whenever it sees a primary hcd being released (which is not a very good idea in any case), but in the course of releasing the primary hcd, it changes the pointers in the shared hcd in such a way that the shared hcd will appear to be primary when it gets released. This patch fixes the problem by changing hcd_release() so that it deallocates the bandwidth_mutex only when the _last_ hcd structure referencing it is released. The patch also removes an unnecessary test, so that when an hcd is released, both the shared_hcd and primary_hcd pointers in the hcd's peer will be cleared. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-by:
Chung-Geol Kim <chunggeol.kim@samsung.com> Tested-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.16: free only usb_hcd::bandwidth_mutex, not usb_hcd::address0_mutex too] Signed-off-by:
-
Al Viro authored
commit d20cb71d upstream. In "NFSv4: Move dentry instantiation into the NFSv4-specific atomic open code" unconditional d_drop() after the ->open_context() had been removed. It had been correct for success cases (there ->open_context() itself had been doing dcache manipulations), but not for error ones. Only one of those (ENOENT) got a compensatory d_drop() added in that commit, but in fact it should've been done for all errors. As it is, the case of O_CREAT non-exclusive open on a hashed negative dentry racing with e.g. symlink creation from another client ended up with ->open_context() getting an error and proceeding to call nfs_lookup(). On a hashed dentry, which would've instantly triggered BUG_ON() in d_materialise_unique() (or, these days, its equivalent in d_splice_alias()). Tested-by:
Oleg Drokin <green@linuxhacker.ru> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
James Morse authored
commit 591d215a upstream. kvm provides kvm_vcpu_uninit(), which amongst other things, releases the last reference to the struct pid of the task that was last running the vcpu. On arm64 built with CONFIG_DEBUG_KMEMLEAK, starting a guest with kvmtool, then killing it with SIGKILL results (after some considerable time) in: > cat /sys/kernel/debug/kmemleak > unreferenced object 0xffff80007d5ea080 (size 128): > comm "lkvm", pid 2025, jiffies 4294942645 (age 1107.776s) > hex dump (first 32 bytes): > 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ > 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ > backtrace: > [<ffff8000001b30ec>] create_object+0xfc/0x278 > [<ffff80000071da34>] kmemleak_alloc+0x34/0x70 > [<ffff80000019fa2c>] kmem_cache_alloc+0x16c/0x1d8 > [<ffff8000000d0474>] alloc_pid+0x34/0x4d0 > [<ffff8000000b5674>] copy_process.isra.6+0x79c/0x1338 > [<ffff8000000b633c>] _do_fork+0x74/0x320 > [<ffff8000000b66b0>] SyS_clone+0x18/0x20 > [<ffff800000085cb0>] el0_svc_naked+0x24/0x28 > [<ffffffffffffffff>] 0xffffffffffffffff On x86 kvm_vcpu_uninit() is called on the path from kvm_arch_destroy_vm(), on arm no equivalent call is made. Add the call to kvm_arch_vcpu_free(). Signed-off-by:
James Morse <james.morse@arm.com> Fixes: 749cf76c ("KVM: ARM: Initial skeleton to compile KVM support") Acked-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
Christoffer Dall <christoffer.dall@linaro.org> [bwh: Backported to 3.16: adjust context] Signed-off-by:
-
Cyril Bur authored
commit 8e96a87c upstream. Userspace can quite legitimately perform an exec() syscall with a suspended transaction. exec() does not return to the old process, rather it load a new one and starts that, the expectation therefore is that the new process starts not in a transaction. Currently exec() is not treated any differently to any other syscall which creates problems. Firstly it could allow a new process to start with a suspended transaction for a binary that no longer exists. This means that the checkpointed state won't be valid and if the suspended transaction were ever to be resumed and subsequently aborted (a possibility which is exceedingly likely as exec()ing will likely doom the transaction) the new process will jump to invalid state. Secondly the incorrect attempt to keep the transactional state while still zeroing state for the new process creates at least two TM Bad Things. The first triggers on the rfid to return to userspace as start_thread() has given the new process a 'clean' MSR but the suspend will still be set in the hardware MSR. The second TM Bad Thing triggers in __switch_to() as the processor is still transactionally suspended but __switch_to() wants to zero the TM sprs for the new process. This is an example of the outcome of calling exec() with a suspended transaction. Note the first 700 is likely the first TM bad thing decsribed earlier only the kernel can't report it as we've loaded userspace registers. c000000000009980 is the rfid in fast_exception_return() Bad kernel stack pointer 3fffcfa1a370 at c000000000009980 Oops: Bad kernel stack pointer, sig: 6 [#1] CPU: 0 PID: 2006 Comm: tm-execed Not tainted NIP: c000000000009980 LR: 0000000000000000 CTR: 0000000000000000 REGS: c00000003ffefd40 TRAP: 0700 Not tainted MSR: 8000000300201031 <SF,ME,IR,DR,LE,TM[SE]> CR: 00000000 XER: 00000000 CFAR: c0000000000098b4 SOFTE: 0 PACATMSCRATCH: b00000010000d033 GPR00: 0000000000000000 00003fffcfa1a370 0000000000000000 0000000000000000 GPR04: 0000000000000000 0000000000000000 0000000000000000 0000000000000000 GPR08: 0000000000000000 0000000000000000 0000000000000000 0000000000000000 GPR12: 00003fff966611c0 0000000000000000 0000000000000000 0000000000000000 NIP [c000000000009980] fast_exception_return+0xb0/0xb8 LR [0000000000000000] (null) Call Trace: Instruction dump: f84d0278 e9a100d8 7c7b03a6 e84101a0 7c4ff120 e8410170 7c5a03a6 e8010070 e8410080 e8610088 e8810090 e8210078 <4c000024> 48000000 e8610178 88ed023b Kernel BUG at c000000000043e80 [verbose debug info unavailable] Unexpected TM Bad Thing exception at c000000000043e80 (msr 0x201033) Oops: Unrecoverable exception, sig: 6 [#2] CPU: 0 PID: 2006 Comm: tm-execed Tainted: G D task: c0000000fbea6d80 ti: c00000003ffec000 task.ti: c0000000fb7ec000 NIP: c000000000043e80 LR: c000000000015a24 CTR: 0000000000000000 REGS: c00000003ffef7e0 TRAP: 0700 Tainted: G D MSR: 8000000300201033 <SF,ME,IR,DR,RI,LE,TM[SE]> CR: 28002828 XER: 00000000 CFAR: c000000000015a20 SOFTE: 0 PACATMSCRATCH: b00000010000d033 GPR00: 0000000000000000 c00000003ffefa60 c000000000db5500 c0000000fbead000 GPR04: 8000000300001033 2222222222222222 2222222222222222 00000000ff160000 GPR08: 0000000000000000 800000010000d033 c0000000fb7e3ea0 c00000000fe00004 GPR12: 0000000000002200 c00000000fe00000 0000000000000000 0000000000000000 GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000 GPR20: 0000000000000000 0000000000000000 c0000000fbea7410 00000000ff160000 GPR24: c0000000ffe1f600 c0000000fbea8700 c0000000fbea8700 c0000000fbead000 GPR28: c000000000e20198 c0000000fbea6d80 c0000000fbeab680 c0000000fbea6d80 NIP [c000000000043e80] tm_restore_sprs+0xc/0x1c LR [c000000000015a24] __switch_to+0x1f4/0x420 Call Trace: Instruction dump: 7c800164 4e800020 7c0022a6 f80304a8 7c0222a6 f80304b0 7c0122a6 f80304b8 4e800020 e80304a8 7c0023a6 e80304b0 <7c0223a6> e80304b8 7c0123a6 4e800020 This fixes CVE-2016-5828. Fixes: bc2a9408 ("powerpc: Hook in new transactional memory code") Signed-off-by:
-
Mark Brown authored
commit 68b356eb upstream. Currently the ad7266 driver treats any failure to get vref as though the regulator were not present but this means that if probe deferral is triggered the driver will act as though the regulator were not present. Instead only use the internal reference if we explicitly got -ENODEV which is what is returned for absent regulators. Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Mark Brown authored
commit e5511c81 upstream. The ad7266 driver attempts to support deciding between the use of internal and external power supplies by checking to see if an error is returned when requesting the regulator. This doesn't work with the current code since the driver uses a normal regulator_get() which is for non-optional supplies and so assumes that if a regulator is not provided by the platform then this is a bug in the platform integration and so substitutes a dummy regulator. Use regulator_get_optional() instead which indicates to the framework that the regulator may be absent and provides a dummy regulator instead. Signed-off-by:
-
Mark Brown authored
commit 6b7f4e25 upstream. All regulator_get() variants return either a pointer to a regulator or an ERR_PTR() so testing for NULL makes no sense and may lead to bugs if we use NULL as a valid regulator. Fix this by using IS_ERR() as expected. Signed-off-by:
-
Linus Walleij authored
commit 0c1f91b9 upstream. These two spi_w8r8() calls return a value with is used by the code following the error check. The dubious use was caused by a cleanup patch. Fixes: d34dbee8 ("staging:iio:accel:kxsd9 cleanup and conversion to iio_chan_spec.") Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Luis de Bethencourt authored
commit ef3149eb upstream. sca3000_read_ctrl_reg() returns a negative number on failure, check for this instead of zero. Signed-off-by:
Luis de Bethencourt <luisbg@osg.samsung.com> Signed-off-by:
-
Torsten Hilbrich authored
commit 63d2f95d upstream. The value `bytes' comes from the filesystem which is about to be mounted. We cannot trust that the value is always in the range we expect it to be. Check its value before using it to calculate the length for the crc32_le call. It value must be larger (or equal) sumoff + 4. This fixes a kernel bug when accidentially mounting an image file which had the nilfs2 magic value 0x3434 at the right offset 0x406 by chance. The bytes 0x01 0x00 were stored at 0x408 and were interpreted as a s_bytes value of 1. This caused an underflow when substracting sumoff + 4 (20) in the call to crc32_le. BUG: unable to handle kernel paging request at ffff88021e600000 IP: crc32_le+0x36/0x100 ... Call Trace: nilfs_valid_sb.part.5+0x52/0x60 [nilfs2] nilfs_load_super_block+0x142/0x300 [nilfs2] init_nilfs+0x60/0x390 [nilfs2] nilfs_mount+0x302/0x520 [nilfs2] mount_fs+0x38/0x160 vfs_kern_mount+0x67/0x110 do_mount+0x269/0xe00 SyS_mount+0x9f/0x100 entry_SYSCALL_64_fastpath+0x16/0x71 Link: http://lkml.kernel.org/r/1466778587-5184-2-git-send-email-konishi.ryusuke@lab.ntt.co.jpSigned-off-by:
Torsten Hilbrich <torsten.hilbrich@secunet.com> Tested-by:
Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Anthony Romano authored
commit b9b4bb26 upstream. When fallocate is interrupted it will undo a range that extends one byte past its range of allocated pages. This can corrupt an in-use page by zeroing out its first byte. Instead, undo using the inclusive byte range. Fixes: 1635f6a7 ("tmpfs: undo fallocation on failure") Link: http://lkml.kernel.org/r/1462713387-16724-1-git-send-email-anthony.romano@coreos.comSigned-off-by:
Anthony Romano <anthony.romano@coreos.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Hugh Dickins <hughd@google.com> Cc: Brandon Philips <brandon@ifup.co> Signed-off-by:
-
Steve French authored
commit 4fcd1813 upstream. Azure server blocks clients that open a socket and don't do anything on it. In our reconnect scenarios, we can reconnect the tcp session and detect the socket is available but we defer the negprot and SMB3 session setup and tree connect reconnection until the next i/o is requested, but this looks suspicous to some servers who expect SMB3 negprog and session setup soon after a socket is created. In the echo thread, reconnect SMB3 sessions and tree connections that are disconnected. A later patch will replay persistent (and resilient) handle opens. Signed-off-by:
Steve French <steve.french@primarydata.com> Acked-by:
Pavel Shilovsky <pshilovsky@samba.org> Signed-off-by:
-
Ben Hutchings authored
commit 99965378 upstream. Use set_posix_acl, which includes proper permission checks, instead of calling ->set_acl directly. Without this anyone may be able to grant themselves permissions to a file by setting the ACL. Lock the inode to make the new checks atomic with respect to set_acl. (Also, nfsd was the only caller of set_acl not locking the inode, so I suspect this may fix other races.) This also simplifies the code, and ensures our ACLs are checked by posix_acl_valid. The permission checks and the inode locking were lost with commit 4ac7249e, which changed nfsd to use the set_acl inode operation directly instead of going through xattr handlers. Reported-by:
David Sinquin <david@sinquin.eu> [agreunba@redhat.com: use set_posix_acl] Fixes: 4ac7249e Cc: Christoph Hellwig <hch@infradead.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
J. Bruce Fields <bfields@redhat.com> [carnil: backport for 3.16: adjust context] Signed-off-by:
-
Andreas Gruenbacher authored
commit 485e71e8 upstream. Factor out part of posix_acl_xattr_set into a common function that takes a posix_acl, which nfsd can also call. The prototype already exists in include/linux/posix_acl.h. Signed-off-by:
Andreas Gruenbacher <agruenba@redhat.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Takashi Iwai authored
commit d5dbbe65 upstream. syzkaller fuzzer spotted a potential use-after-free case in snd-dummy driver when hrtimer is used as backend: > ================================================================== > BUG: KASAN: use-after-free in rb_erase+0x1b17/0x2010 at addr ffff88005e5b6f68 > Read of size 8 by task syz-executor/8984 > ============================================================================= > BUG kmalloc-192 (Not tainted): kasan: bad access detected > ----------------------------------------------------------------------------- > > Disabling lock debugging due to kernel taint > INFO: Allocated in 0xbbbbbbbbbbbbbbbb age=18446705582212484632 > .... > [< none >] dummy_hrtimer_create+0x49/0x1a0 sound/drivers/dummy.c:464 > .... > INFO: Freed in 0xfffd8e09 age=18446705496313138713 cpu=2164287125 pid=-1 > [< none >] dummy_hrtimer_free+0x68/0x80 sound/drivers/dummy.c:481 > .... > Call Trace: > [<ffffffff8179e59e>] __asan_report_load8_noabort+0x3e/0x40 mm/kasan/report.c:333 > [< inline >] rb_set_parent include/linux/rbtree_augmented.h:111 > [< inline >] __rb_erase_augmented include/linux/rbtree_augmented.h:218 > [<ffffffff82ca5787>] rb_erase+0x1b17/0x2010 lib/rbtree.c:427 > [<ffffffff82cb02e8>] timerqueue_del+0x78/0x170 lib/timerqueue.c:86 > [<ffffffff814d0c80>] __remove_hrtimer+0x90/0x220 kernel/time/hrtimer.c:903 > [< inline >] remove_hrtimer kernel/time/hrtimer.c:945 > [<ffffffff814d23da>] hrtimer_try_to_cancel+0x22a/0x570 kernel/time/hrtimer.c:1046 > [<ffffffff814d2742>] hrtimer_cancel+0x22/0x40 kernel/time/hrtimer.c:1066 > [<ffffffff85420531>] dummy_hrtimer_stop+0x91/0xb0 sound/drivers/dummy.c:417 > [<ffffffff854228bf>] dummy_pcm_trigger+0x17f/0x1e0 sound/drivers/dummy.c:507 > [<ffffffff85392170>] snd_pcm_do_stop+0x160/0x1b0 sound/core/pcm_native.c:1106 > [<ffffffff85391b26>] snd_pcm_action_single+0x76/0x120 sound/core/pcm_native.c:956 > [<ffffffff85391e01>] snd_pcm_action+0x231/0x290 sound/core/pcm_native.c:974 > [< inline >] snd_pcm_stop sound/core/pcm_native.c:1139 > [<ffffffff8539754d>] snd_pcm_drop+0x12d/0x1d0 sound/core/pcm_native.c:1784 > [<ffffffff8539d3be>] snd_pcm_common_ioctl1+0xfae/0x2150 sound/core/pcm_native.c:2805 > [<ffffffff8539ee91>] snd_pcm_capture_ioctl1+0x2a1/0x5e0 sound/core/pcm_native.c:2976 > [<ffffffff8539f2ec>] snd_pcm_kernel_ioctl+0x11c/0x160 sound/core/pcm_native.c:3020 > [<ffffffff853d9a44>] snd_pcm_oss_sync+0x3a4/0xa30 sound/core/oss/pcm_oss.c:1693 > [<ffffffff853da27d>] snd_pcm_oss_release+0x1ad/0x280 sound/core/oss/pcm_oss.c:2483 > ..... A workaround is to call hrtimer_cancel() in dummy_hrtimer_sync() which is called certainly before other blocking ops. Reported-by:
Dmitry Vyukov <dvyukov@google.com> Tested-by:
-
Scott Bauer authored
commit 93a2001b upstream. This patch validates the num_values parameter from userland during the HIDIOCGUSAGES and HIDIOCSUSAGES commands. Previously, if the report id was set to HID_REPORT_ID_UNKNOWN, we would fail to validate the num_values parameter leading to a heap overflow. Signed-off-by:
Scott Bauer <sbauer@plzdonthack.me> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Jerome Marchand authored
commit b8da344b upstream. In sess_auth_rawntlmssp_authenticate(), the ntlmssp blob is allocated statically and its size is an "empirical" 5*sizeof(struct _AUTHENTICATE_MESSAGE) (320B on x86_64). I don't know where this value comes from or if it was ever appropriate, but it is currently insufficient: the user and domain name in UTF16 could take 1kB by themselves. Because of that, build_ntlmssp_auth_blob() might corrupt memory (out-of-bounds write). The size of ntlmssp_blob in SMB2_sess_setup() is too small too (sizeof(struct _NEGOTIATE_MESSAGE) + 500). This patch allocates the blob dynamically in build_ntlmssp_auth_blob(). Signed-off-by:
Jerome Marchand <jmarchan@redhat.com> Signed-off-by:
Steve French <smfrench@gmail.com> [bwh: Backported to 3.16: adjust context, indentation] Signed-off-by:
-
Jerome Marchand authored
commit 202d772b upstream. Currently in build_ntlmssp_auth_blob(), when converting the domain name to UTF16, CIFS_MAX_USERNAME_LEN limit is used. It should be CIFS_MAX_DOMAINNAME_LEN. This patch fixes this. Signed-off-by:
-
Dmitry Torokhov authored
commit 226ba707 upstream. The touchpad in HP Pavilion 14-ab057ca reports it's version as 12 and according to Elan both 11 and 12 are valid IC types and should be identified as hw_version 4. Reported-by:
Patrick Lessard <Patrick.Lessard@cogeco.com> Tested-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
