Check "ch" on NULL first, then get ctlr.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jason Wang says:

====================
vhost_net tx batching

This series tries to implement tx batching support for vhost. This was
done by using MSG_MORE as a hint for under layer socket. The backend
(e.g tap) can then batch the packets temporarily in a list and
submit it all once the number of bacthed exceeds a limitation.

Tests shows obvious improvement on guest pktgen over over
mlx4(noqueue) on host:

                                     Mpps  -+%
        rx-frames = 0                0.91  +0%
        rx-frames = 4                1.00  +9.8%
        rx-frames = 8                1.00  +9.8%
        rx-frames = 16               1.01  +10.9%
        rx-frames = 32               1.07  +17.5%
        rx-frames = 48               1.07  +17.5%
        rx-frames = 64               1.08  +18.6%
        rx-frames = 64 (no MSG_MORE) 0.91  +0%

Changes from V4:
- stick to NAPI_POLL_WEIGHT for rx-frames is user specify a value
  greater than it.
Changes from V3:
- use ethtool instead of module parameter to control the maximum
  number of batched packets
- avoid overhead when MSG_MORE were not set and no packet queued
Changes from V2:
- remove uselss queue limitation check (and we don't drop any packet now)
Changes from V1:
- drop NAPI handler since we don't use NAPI now
- fix the issues that may exceeds max pending of zerocopy
- more improvement on available buffer detection
- move the limitation of batched pacekts from vhost to tuntap
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We can only process 1 packet at one time during sendmsg(). This often
lead bad cache utilization under heavy load. So this patch tries to do
some batching during rx before submitting them to host network
stack. This is done through accepting MSG_MORE as a hint from
sendmsg() caller, if it was set, batch the packet temporarily in a
linked list and submit them all once MSG_MORE were cleared.

Tests were done by pktgen (burst=128) in guest over mlx4(noqueue) on host:

                                 Mpps  -+%
    rx-frames = 0                0.91  +0%
    rx-frames = 4                1.00  +9.8%
    rx-frames = 8                1.00  +9.8%
    rx-frames = 16               1.01  +10.9%
    rx-frames = 32               1.07  +17.5%
    rx-frames = 48               1.07  +17.5%
    rx-frames = 64               1.08  +18.6%
    rx-frames = 64 (no MSG_MORE) 0.91  +0%

User were allowed to change per device batched packets through
ethtool -C rx-frames. NAPI_POLL_WEIGHT were used as upper limitation
to prevent bh from being disabled too long.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch tries to utilize tuntap rx batching by peeking the tx
virtqueue during transmission, if there's more available buffers in
the virtqueue, set MSG_MORE flag for a hint for backend (e.g tuntap)
to batch the packets.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch tries to do several tweaks on vhost_vq_avail_empty() for a
better performance:

- check cached avail index first which could avoid userspace memory access.
- using unlikely() for the failure of userspace access
- check vq->last_avail_idx instead of cached avail index as the last
  step.

This patch is need for batching supports which needs to peek whether
or not there's still available buffers in the ring.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Relax ordering(RO) is one feature of 82599 NIC, to enable this feature can
enhance the performance for some cpu architecure, such as SPARC and so on.
Currently it only supports one special cpu architecture(SPARC) in 82599
driver to enable RO feature, this is not very common for other cpu architecture
which really needs RO feature.
This patch add one common config CONFIG_ARCH_WANT_RELAX_ORDER to set RO feature,
and should define CONFIG_ARCH_WANT_RELAX_ORDER in sparc Kconfig firstly.
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Reviewed-by: Alexander Duyck <alexander.duyck@gmail.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Ahern says:

====================
net: ipv6: simplify rt6_fill_node

Remove a couple of unnecessary input arguments to rt6_fill_node.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The prefix arg to rt6_fill_node is non-0 in only 1 path - rt6_dump_route
where a user is requesting a prefix only dump. Simplify rt6_fill_node
by removing the prefix arg and moving the prefix check to rt6_dump_route.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All callers of rt6_fill_node pass 0 for nowait arg. Remove the arg and
simplify rt6_fill_node accordingly.

rt6_fill_node passes the nowait of 0 to ip6mr_get_route. Remove the
nowait arg from it as well.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Xin Long says:

====================
sctp: add sender-side procedures for stream reconf ssn reset request chunk

Patch 6/6 is to implement sender-side procedures for the Outgoing
and Incoming SSN Reset Request Parameter described in rfc6525
section 5.1.2 and 5.1.3

Patches 1-5/6 are ahead of it to define some apis and asoc members
for it.

Note that with this patchset, asoc->reconf_enable has no chance yet to
be set, until the patch "sctp: add get and set sockopt for reconf_enable"
is applied in the future. As we can not just enable it when sctp is not
capable of processing reconf chunk yet.

v1->v2:
  - put these into a smaller group.
  - rename some temporary variables in the codes.
  - rename the titles of the commits and improve some changelogs.
v2->v3:
  - re-split the patchset and make sure it has no dead codes for review.
v3->v4:
  - move sctp_make_reconf() into patch 1/6 to avoid kbuild warning.
  - drop unused struct sctp_strreset_req.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to implement sender-side procedures for the Outgoing
and Incoming SSN Reset Request Parameter described in rfc6525 section
5.1.2 and 5.1.3.

It is also add sockopt SCTP_RESET_STREAMS in rfc6525 section 6.3.2
for users.

Note that the new asoc member strreset_outstanding is to make sure
only one reconf request chunk on the fly as rfc6525 section 5.1.1
demands.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to add sockopt SCTP_ENABLE_STREAM_RESET to get/set
strreset_enable to indicate which reconf request type it supports,
which is described in rfc6525 section 6.3.1.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to add reconf_enable field in all of asoc ep and netns
to indicate if they support stream reset.

When initializing, asoc reconf_enable get the default value from ep
reconf_enable which is from netns netns reconf_enable by default.

It is also to add reconf_capable in asoc peer part to know if peer
supports reconf_enable, the value is set if ext params have reconf
chunk support when processing init chunk, just as rfc6525 section
5.1.1 demands.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to add a primitive based on sctp primitive frame for
sending stream reconf request. It works as the other primitives,
and create a SCTP_CMD_REPLY command to send the request chunk out.

sctp_primitive_RECONF would be the api to send a reconf request
chunk.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to add a per transport timer based on sctp timer frame
for stream reconf chunk retransmission. It would start after sending
a reconf request chunk, and stop after receiving the response chunk.

If the timer expires, besides retransmitting the reconf request chunk,
it would also do the same thing with data RTO timer. like to increase
the appropriate error counts, and perform threshold management, possibly
destroying the asoc if sctp retransmission thresholds are exceeded, just
as section 5.1.1 describes.

This patch is also to add asoc strreset_chunk, it is used to save the
reconf request chunk, so that it can be retransmitted, and to check if
the response is really for this request by comparing the information
inside with the response chunk as well.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to add asoc strreset_outseq and strreset_inseq for
saving the reconf request sequence, initialize them when create
assoc and process init, and also to define Incoming and Outgoing
SSN Reset Request Parameter described in rfc6525 section 4.1 and
4.2, As they can be in one same chunk as section rfc6525 3.1-3
describes, it makes them in one function.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Josef Bacik says:

====================
Rework inet_csk_get_port

V3->V4:
-Removed the random include of addrconf.h that is no longer needed.

V2->V3:
-Dropped the fastsock from the tb and instead just carry the saddrs, family, and
 ipv6 only flag.
-Reworked the helper functions to deal with this change so I could still use
 them when checking the fast path.
-Killed tb->num_owners as per Eric's request.
-Attached a reproducer to the bottom of this email.

V1->V2:
-Added a new patch 'inet: collapse ipv4/v6 rcv_saddr_equal functions into one'
 at Hannes' suggestion.
-Dropped ->bind_conflict and just use the new helper.
-Fixed a compile bug from the original ->bind_conflict patch.

The original description of the series follows:

At some point recently the guys working on our load balancer added the ability
to use SO_REUSEPORT.  When they restarted their app with this option enabled
they immediately hit a softlockup on what appeared to be the
inet_bind_bucket->lock.  Eventually what all of our debugging and discussion led
us to was the fact that the application comes up without SO_REUSEPORT, shuts
down which creates around 100k twsk's, and then comes up and tries to open a
bunch of sockets using SO_REUSEPORT, which meant traversing the inet_bind_bucket
owners list under the lock.  Since this lock is needed for dealing with the
twsk's and basically anything else related to connections we would softlockup,
and sometimes not ever recover.

To solve this problem I did what you see in Path 5/5.  Once we have a
SO_REUSEPORT socket on the tb->owners list we know that the socket has no
conflicts with any of the other sockets on that list.  So we can add a copy of
the sock_common (really all we need is the recv_saddr but it seemed ugly to copy
just the ipv6, ipv4, and flag to indicate if we were ipv6 only in there so I've
copied the whole common) in order to check subsequent SO_REUSEPORT sockets.  If
they match the previous one then we can skip the expensive
inet_csk_bind_conflict check.  This is what eliminated the soft lockup that we
were seeing.

Patches 1-4 are cleanups and re-workings.  For instance when we specify port ==
0 we need to find an open port, but we would do two passes through
inet_csk_bind_conflict every time we found a possible port.  We would also keep
track of the smallest_port value in order to try and use it if we found no
port our first run through.  This however made no sense as it would have had to
fail the first pass through inet_csk_bind_conflict, so would not actually pass
the second pass through either.  Finally I split the function into two functions
in order to make it easier to read and to distinguish between the two behaviors.

I have tested this on one of our load balancing boxes during peak traffic and it
hasn't fallen over.  But this is not my area, so obviously feel free to point
out where I'm being stupid and I'll get it fixed up and retested.  Thanks,
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If we have non reuseport sockets on a tb we will set tb->fastreuseport to 0 and
never set it again.  Which means that in the future if we end up adding a bunch
of reuseport sk's to that tb we'll have to do the expensive scan every time.
Instead add the ipv4/ipv6 saddr fields to the bind bucket, as well as the family
so we know what comparison to make, and the ipv6 only setting so we can make
sure to compare with new sockets appropriately.  Once one sk has made it onto
the list we know that there are no potential bind conflicts on the owners list
that match that sk's rcv_addr.  So copy the sk's information into our bind
bucket and set tb->fastruseport to FASTREUSESOCK_STRICT so we know we have to do
an extra check for subsequent reuseport sockets and skip the expensive bind
conflict check.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

inet_csk_get_port does two different things, it either scans for an open port,
or it tries to see if the specified port is available for use.  Since these two
operations have different rules and are basically independent lets split them
into two different functions to make them both more readable.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is just wasted time, we've already found a tb that doesn't have a bind
conflict, and we don't drop the head lock so scanning again isn't going to give
us a different answer.  Instead move the tb->reuse setting logic outside of the
found_tb path and put it in the success: path.  Then make it so that we don't
goto again if we find a bind conflict in the found_tb path as we won't reach
this anymore when we are scanning for an ephemeral port.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In inet_csk_get_port we seem to be using smallest_port to figure out where the
best place to look for a SO_REUSEPORT sk that matches with an existing set of
SO_REUSEPORT's.  However if we get to the logic

if (smallest_size != -1) {
	port = smallest_port;
	goto have_port;
}

we will do a useless search, because we would have already done the
inet_csk_bind_conflict for that port and it would have returned 1, otherwise we
would have gone to found_tb and succeeded.  Since this logic makes us do yet
another trip through inet_csk_bind_conflict for a port we know won't work just
delete this code and save us the time.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The only difference between inet6_csk_bind_conflict and inet_csk_bind_conflict
is how they check the rcv_saddr, so delete this call back and simply
change inet_csk_bind_conflict to call inet_rcv_saddr_equal.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We pass these per-protocol equal functions around in various places, but
we can just have one function that checks the sk->sk_family and then do
the right comparison function.  I've also changed the ipv4 version to
not cast to inet_sock since it is unneeded.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds more info to stmicro' Kconfig files in order to be clearer
that the driver can be used by ethernet cards based on 10/100/1000/EQOS
Synopsys IP Cores.

EQOS was also added stmmac/Kconfig Kconfig, since dwmac4 is in fact EQoS,
one of Synopsys Ethernet IPs. More info at:
https://www.synopsys.com/dw/ipdir.php?ds=dwc_ether_qosSigned-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds bpf_xdp_adjust_head() support to mlx5e.

1. rx_headroom is added to struct mlx5e_rq.  It uses
   an existing 4 byte hole in the struct.
2. The adjusted data length is checked against
   MLX5E_XDP_MIN_INLINE and MLX5E_SW2HW_MTU(rq->netdev->mtu).
3. The macro MLX5E_SW2HW_MTU is moved from en_main.c to en.h.
   MLX5E_HW2SW_MTU is also moved to en.h for symmetric reason
   but it is not a must.

v2:
- Keep the xdp specific logic in mlx5e_xdp_handle()
- Update dma_len after the sanity checks in mlx5e_xmit_xdp_frame()
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Using a Mac OSX box as a client connecting to a Linux server, we have found
that when certain applications (such as 'ab'), are abruptly terminated
(via ^C), a FIN is sent followed by a RST packet on tcp connections. The
FIN is accepted by the Linux stack but the RST is sent with the same
sequence number as the FIN, and Linux responds with a challenge ACK per
RFC 5961. The OSX client then sometimes (they are rate-limited) does not
reply with any RST as would be expected on a closed socket.

This results in sockets accumulating on the Linux server left mostly in
the CLOSE_WAIT state, although LAST_ACK and CLOSING are also possible.
This sequence of events can tie up a lot of resources on the Linux server
since there may be a lot of data in write buffers at the time of the RST.
Accepting a RST equal to rcv_nxt - 1, after we have already successfully
processed a FIN, has made a significant difference for us in practice, by
freeing up unneeded resources in a more expedient fashion.

A packetdrill test demonstrating the behavior:

// testing mac osx rst behavior

// Establish a connection
0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
0.000 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
0.000 bind(3, ..., ...) = 0
0.000 listen(3, 1) = 0

0.100 < S 0:0(0) win 32768 <mss 1460,nop,wscale 10>
0.100 > S. 0:0(0) ack 1 <mss 1460,nop,wscale 5>
0.200 < . 1:1(0) ack 1 win 32768
0.200 accept(3, ..., ...) = 4

// Client closes the connection
0.300 < F. 1:1(0) ack 1 win 32768

// now send rst with same sequence
0.300 < R. 1:1(0) ack 1 win 32768

// make sure we are in TCP_CLOSE
0.400 %{
assert tcpi_state == 7
}%
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: Eric Dumazet <edumazet@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make the needlessly global struct ethtool_ops ethoc_ethtool_ops static
to fix a sparse warning.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Edward Cree says:

====================
sfc: RX hash configuration

This series improves support for getting and setting RX hashing
 configuration on Solarflare adapters through ethtool.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Ensures that we report the key and indirection table the NIC is using,
 rather than (if setting them failed earlier) what we wanted it to use.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The inet_num is u16, so use %hu instead of casting it to int. And
the sk_bound_dev_if is int actually, so it needn't cast to int.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use eth_zero_addr to assign zero address to the given address array
instead of memset when the second argument in memset is address
of zero. Also, it makes the code clearer
Signed-off-by: Shyam Saini <mayhs11saini@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Changed type of csum field in struct igmpv3_query from __be16 to
__sum16 to eliminate type warning, made same change in struct
igmpv3_report for consistency.

Fixed up an ntohs() where htons() should have been used instead.
Signed-off-by: Lance Richardson <lrichard@redhat.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Robert Shearman says:

====================
mpls: Packet stats

This patchset records per-interface packet stats in the MPLS
forwarding path and exports them using a nest of attributes root at a
new IFLA_STATS_AF_SPEC attribute as part of RTM_GETSTATS messages:

[IFLA_STATS_AF_SPEC]
 -> [AF_MPLS]
  -> [MPLS_STATS_LINK]
   -> struct mpls_link_stats

The first patch adds the rtnl infrastructure for this, including a new
callbacks to per-AF ops of fill_stats_af and get_stats_af_size. The
second patch records MPLS stats and makes use of the infrastructure to
export them. The rtnl infrastructure could also be used to export IPv6
stats in the future.

Changes in v2:
 - make incrementing IPv6 stats in mpls_stats_inc_outucastpkts
   conditional on CONFIG_IPV6 to fix build with CONFIG_IPV6=n
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Having MPLS packet stats is useful for observing network operation and
for diagnosing network problems. In the absence of anything better,
RFC2863 and RFC3813 are used for guidance for which stats to expose
and the semantics of them. In particular rx_noroutes maps to in
unknown protos in RFC2863. The stats are exposed to userspace via
AF_MPLS attributes embedded in the IFLA_STATS_AF_SPEC attribute of
RTM_GETSTATS messages.

All the introduced fields are 64-bit, even error ones, to ensure no
overflow with long uptimes. Per-CPU counters are used to avoid
cache-line contention on the commonly used fields. The other fields
have also been made per-CPU for code to avoid performance problems in
error conditions on the assumption that on some platforms the cost of
atomic operations could be more expensive than sending the packet
(which is what would be done in the success case). If that's not the
case, we could instead not use per-CPU counters for these fields.

Only unicast and non-fragment are exposed at the moment, but other
counters can be exposed in the future either by adding to the end of
struct mpls_link_stats or by additional netlink attributes in the
AF_MPLS IFLA_STATS_AF_SPEC nested attribute.
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the functionality for including address-family-specific per-link
stats in RTM_GETSTATS messages. This is done through adding a new
IFLA_STATS_AF_SPEC attribute under which address family attributes are
nested and then the AF-specific attributes can be further nested. This
follows the model of IFLA_AF_SPEC on RTM_*LINK messages and it has the
advantage of presenting an easily extended hierarchy. The rtnl_af_ops
structure is extended to provide AFs with the opportunity to fill and
provide the size of their stats attributes.

One alternative would have been to provide AFs with the ability to add
attributes directly into the RTM_GETSTATS message without a nested
hierarchy. I discounted this approach as it increases the rate at
which the 32 attribute number space is used up and it makes
implementation a little more tricky for stats dump resuming (at the
moment the order in which attributes are added to the message has to
match the numeric order of the attributes).

Another alternative would have been to register per-AF RTM_GETSTATS
handlers. I discounted this approach as I perceived a common use-case
to be getting all the stats for an interface and this approach would
necessitate multiple requests/dumps to retrieve them all.
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function stmmac_dt_phy provides several possibilities for initializing
plat->mdio_node, all of which have the effect of increasing the reference
count of the assigned value.  This field is not updated elsewhere, so the
value is live until the end of the lifetime of plat (devm_allocated), just
after the end of stmmac_remove_config_dt.  Thus, add an of_node_put on
plat->mdio_node in stmmac_remove_config_dt.  It is possible that the field
mdio_node is never initialized, but of_node_put is NULL-safe, so it is also
safe to call of_node_put in that case.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch part reverts fd2a0437 and e858fae2 which introduced a
subtle change in how the virtio_net flags are derived from the SKBs
ip_summed field.

With the above commits, the flags are set to VIRTIO_NET_HDR_F_DATA_VALID
when ip_summed == CHECKSUM_UNNECESSARY, thus treating it differently to
ip_summed == CHECKSUM_NONE, which should be the same.

Further, the virtio spec 1.0 / CS04 explicitly says that
VIRTIO_NET_HDR_F_DATA_VALID must not be set by the driver.

Fixes: fd2a0437 ("virtio_net: introduce virtio_net_hdr_{from,to}_skb")
Fixes: e858fae2 (" virtio_net: use common code for virtio_net_hdr and skb GSO conversion")
Signed-off-by: Rolf Neugebauer <rolf.neugebauer@docker.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>