- 23 Sep, 2016 11 commits
-
-
Or Gerlitz authored
The HW can be programmed to push vlan, pop vlan or both. A factorization step towards using the push/pop capabilties in the eswitch offloads mode. This patch doesn't add new functionality. Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Or Gerlitz authored
The structure we use for the eswitch vport representor (mlx5_eswitch_rep) has some fields which are set from upper layers in the driver when they register the rep. Use explicit setting on registration time for them and avoid global memcpy. This patch doesn't add new functionality. Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Or Gerlitz authored
Set the vport value in the PF entry to be that of the uplink so we can use it blindly over the tc / eswitch offload code without translating it each time we deal with the uplink representor. Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Or Gerlitz authored
Needed e.g for offloading drivers to pick the relevant attributes. Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
It looks like the following patch can make FQ very precise, even in VM or stressed hosts. It matters at high pacing rates. We take into account the difference between the time that was programmed when last packet was sent, and current time (a drift of tens of usecs is often observed) Add an EWMA of the unthrottle latency to help diagnostics. This latency is the difference between current time and oldest packet in delayed RB-tree. This accounts for the high resolution timer latency, but can be different under stress, as fq_check_throttled() can be opportunistically be called from a dequeue() called after an enqueue() for a different flow. Tested: // Start a 10Gbit flow $ netperf --google-pacing-rate 1250000000 -H lpaa24 -l 10000 -- -K bbr & Before patch : $ sar -n DEV 10 5 | grep eth0 | grep Average Average: eth0 17106.04 756876.84 1102.75 1119049.02 0.00 0.00 0.52 After patch : $ sar -n DEV 10 5 | grep eth0 | grep Average Average: eth0 17867.00 800245.90 1151.77 1183172.12 0.00 0.00 0.52 A new iproute2 tc can output the 'unthrottle latency' : $ tc -s qd sh dev eth0 | grep latency 0 gc, 0 highprio, 32490767 throttled, 2382 ns latency Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Bert Kenward authored
Add a NULL check before calling asynchronous MCDI completion functions during device removal. Fixes: 7014d7f6 ("sfc: allow asynchronous MCDI without completion function") Signed-off-by:
Bert Kenward <bkenward@solarflare.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Marcelo Ricardo Leitner says: ==================== sctp: fix the handling of SACK Gap Ack blocks sctp_acked() is using 32bit arithmetics on 16bits vars, via TSN_lte() macros, which is weird and confusing. Once the offset to ctsn is calculated, all wrapping is already handled and thus to verify the Gap Ack blocks we can just use pure less/big-or-equal than checks. Also, rename gap variable to tsn_offset, so it's more meaningful, as it doesn't point to any gap at all. Even so, I don't think this discrepancy resulted in any practical bug. This patch is a preparation for the next one, which will introduce typecheck() for TSN_lte() macros and would cause a compile error here. Suggested-by:
David Laight <David.Laight@ACULAB.COM> Reported-by:
David Laight <David.Laight@ACULAB.COM> Signed-off-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Marcelo Ricardo Leitner authored
Make it similar to time_before() macros: - easier to understand - make use of typecheck() to avoid working on unexpected variable types (made the issue on previous patch visible) - for _[lg]te versions, slighly faster, as the compiler used to generate a sequence of cmp/je/cmp/js instructions and now it's sub/test/jle (for _lte): Before, for sctp_outq_sack: if (primary->cacc.changeover_active) { 1f01: 80 b9 84 02 00 00 00 cmpb $0x0,0x284(%rcx) 1f08: 74 6e je 1f78 <sctp_outq_sack+0xe8> u8 clear_cycling = 0; if (TSN_lte(primary->cacc.next_tsn_at_change, sack_ctsn)) { 1f0a: 8b 81 80 02 00 00 mov 0x280(%rcx),%eax return ((s) - (t)) & TSN_SIGN_BIT; } static inline int TSN_lte(__u32 s, __u32 t) { return ((s) == (t)) || (((s) - (t)) & TSN_SIGN_BIT); 1f10: 8b 7d bc mov -0x44(%rbp),%edi 1f13: 39 c7 cmp %eax,%edi 1f15: 74 25 je 1f3c <sctp_outq_sack+0xac> 1f17: 39 f8 cmp %edi,%eax 1f19: 78 21 js 1f3c <sctp_outq_sack+0xac> primary->cacc.changeover_active = 0; After: if (primary->cacc.changeover_active) { 1ee7: 80 b9 84 02 00 00 00 cmpb $0x0,0x284(%rcx) 1eee: 74 73 je 1f63 <sctp_outq_sack+0xf3> u8 clear_cycling = 0; if (TSN_lte(primary->cacc.next_tsn_at_change, sack_ctsn)) { 1ef0: 8b 81 80 02 00 00 mov 0x280(%rcx),%eax 1ef6: 2b 45 b4 sub -0x4c(%rbp),%eax 1ef9: 85 c0 test %eax,%eax 1efb: 7e 26 jle 1f23 <sctp_outq_sack+0xb3> primary->cacc.changeover_active = 0; *_lt() generated pretty much the same code. Tested with gcc (GCC) 6.1.1 20160621. This patch also removes SSN_lte as it is not used and cleanups some comments. Signed-off-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Marcelo Ricardo Leitner authored
sctp_acked() is using 32bit arithmetics on 16bits vars, via TSN_lte() macros, which is weird and confusing. Once the offset to ctsn is calculated, all wrapping is already handled and thus to verify the Gap Ack blocks we can just use pure less/big-or-equal than checks. Also, rename gap variable to tsn_offset, so it's more meaningful, as it doesn't point to any gap at all. Even so, I don't think this discrepancy resulted in any practical bug. This patch is a preparation for the next one, which will introduce typecheck() for TSN_lte() macros and would cause a compile error here. Suggested-by:
David Laight <David.Laight@ACULAB.COM> Reported-by:
David Laight <David.Laight@ACULAB.COM> Signed-off-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
WANG Cong authored
On error path in route4_change(), 'f' could be NULL, so we should check NULL before calling tcf_exts_destroy(). Fixes: b9a24bb7 ("net_sched: properly handle failure case of tcf_exts_init()") Reported-by:
kbuild test robot <fengguang.wu@intel.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Acked-by:
Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
-
- 22 Sep, 2016 29 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-mediaLinus Torvalds authored
Pull media fixes from Mauro Carvalho Chehab: - several fixes for new drivers added for Kernel 4.8 addition (cec core, pulse8 cec driver and Mediatek vcodec) - a regression fix for cx23885 and saa7134 drivers - an important fix for rcar-fcp, making rcar_fcp_enable() return 0 on success * tag 'media/v4.8-7' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (25 commits) [media] cx23885/saa7134: assign q->dev to the PCI device [media] rcar-fcp: Make sure rcar_fcp_enable() returns 0 on success [media] cec: fix ioctl return code when not registered [media] cec: don't Feature Abort broadcast msgs when unregistered [media] vcodec:mediatek: Refine VP8 encoder driver [media] vcodec:mediatek: Refine H264 encoder driver [media] vcodec:mediatek: change H264 profile default to profile high [media] vcodec:mediatek: Add timestamp and timecode copy for V4L2 Encoder [media] vcodec:mediatek: Fix visible_height larger than coded_height issue in s_fmt_out [media] vcodec:mediatek: Fix fops_vcodec_release flow for V4L2 Encoder [media] vcodec:mediatek:code refine for v4l2 Encoder driver [media] cec-funcs.h: add missing vendor-specific messages [media] cec-edid: check for IEEE identifier [media] pulse8-cec: fix error handling [media] pulse8-cec: set correct Signal Free Time [media] mtk-vcodec: add HAS_DMA dependency [media] cec: ignore messages when log_addr_mask == 0 [media] cec: add item to TODO [media] cec: set unclaimed addresses to CEC_LOG_ADDR_INVALID [media] cec: add CEC_LOG_ADDRS_FL_ALLOW_UNREG_FALLBACK flag ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds authored
Pull networking fixes from David Miller: "Mostly small bits scattered all over the place, which is usually how things go this late in the -rc series. 1) Proper driver init device resets in bnx2, from Baoquan He. 2) Fix accounting overflow in __tcp_retransmit_skb(), sk_forward_alloc, and ip_idents_reserve, from Eric Dumazet. 3) Fix crash in bna driver ethtool stats handling, from Ivan Vecera. 4) Missing check of skb_linearize() return value in mac80211, from Johannes Berg. 5) Endianness fix in nf_table_trace dumps, from Liping Zhang. 6) SSN comparison fix in SCTP, from Marcelo Ricardo Leitner. 7) Update DSA and b44 MAINTAINERS entries. 8) Make input path of vti6 driver work again, from Nicolas Dichtel. 9) Off-by-one in mlx4, from Sebastian Ott. 10) Fix fallback route lookup handling in ipv6, from Vincent Bernat. 11) Fix stack corruption on probe in qed driver, from Yuval Mintz. 12) PHY init fixes in r8152 from Hayes Wang. 13) Missing SKB free in irda_accept error path, from Phil Turnbull" * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits) tcp: properly account Fast Open SYN-ACK retrans tcp: fix under-accounting retransmit SNMP counters MAINTAINERS: Update b44 maintainer. net: get rid of an signed integer overflow in ip_idents_reserve() net/mlx4_core: Fix to clean devlink resources net: can: ifi: Configure transmitter delay vti6: fix input path ipmr, ip6mr: return lastuse relative to now r8152: disable ALDPS and EEE before setting PHY r8152: remove r8153_enable_eee r8152: move PHY settings to hw_phy_cfg r8152: move enabling PHY r8152: move some functions cxgb4/cxgb4vf: Allocate more queues for 25G and 100G adapter qed: Fix stack corruption on probe MAINTAINERS: Add an entry for the core network DSA code net: ipv6: fallback to full lookup if table lookup is unsuitable net/mlx5: E-Switch, Handle mode change failures net/mlx5: E-Switch, Fix error flow in the SRIOV e-switch init code net/mlx5: Fix flow counter bulk command out mailbox allocation ...
-
Juergen Gross authored
Instead of open coding it use the threaded irq mechanism in xen-netback. Signed-off-by:
Juergen Gross <jgross@suse.com> Acked-by:
Wei Liu <wei.liu2@citrix.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Sean Wang authored
Potential dangerous invalid pointer might be accessed if the error happens when couple phy_device to net_device so cleanup the error path. Signed-off-by:
Sean Wang <sean.wang@mediatek.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Sean Wang authored
1) use new api [get|set]_link_ksettings instead of [get|set]_settings old ones. 2) dev->phydev is sure being ready before calling these callbacks, so removing all the sanity check if it is existing. Signed-off-by:
Sean Wang <sean.wang@mediatek.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Sean Wang authored
remove the unused variable for parsing PHY address and the related logic for sanity test which would be all already handled done when of_mdiobus_register was called Reported-by:
Nelson Chang <nelson.chang@mediatek.com> Signed-off-by:
Sean Wang <sean.wang@mediatek.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Sean Wang authored
reuse phydev already in struct net_device instead of creating another new one in private structure. Signed-off-by:
Sean Wang <sean.wang@mediatek.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Sean Wang says: ==================== mediatek: add support for RGMII on GMAC0 through TRGMII hardware module By default, GMAC0 is connected to built-in switch called MT7530 through the proprietary interface called Turbo RGMII (TRGMII). TRGMII also supports well for RGMII as generic external PHY uses but requires some slight changes to the setup of TRGMII and doesn't have well support on current driver. So this patchset 1) provides the slight changes of the setup for RGMII can work through TRGMII 2) adds additional setting "trgmii" as PHY_INTERFACE_MODE_TRGMII about phy-mode on device tree to make GMAC0 distinguish which mode it runs 3) changes dynamically source clock, TX/RX delay and interface mode on TRGMII for adapting various link Changes since v1: - fixed the style of comment which doesn't have a space at the beginning and end of comment lines - add support for phy-mode "trgmii" as PHY_INTERFACE_MODE_TRGMII into linux/phy.h - enhance the Documentation about device tree binding for trgmii which is applicable only for GMAC0 which uses fixed-link ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Sean Wang authored
Add the dts property for the capability if TRGMII supported on GAMC0 Signed-off-by:
Sean Wang <sean.wang@mediatek.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Sean Wang authored
Changing dynamically source clock, TX/RX delay and interface mode used by TRGMII hardware module inside PHY capability polling routine for adapting to the various speed of RGMII used by external PHY for GMAC0. Signed-off-by:
Sean Wang <sean.wang@mediatek.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Sean Wang authored
adds PHY-mode "trgmii" as an extension for the operation mode of the PHY interface for PHY_INTERFACE_MODE_TRGMII. and adds a variable trgmii inside mtk_mac as the indication to make the difference between the MAC connected to internal switch or connected to external PHY by the given configuration on the board and then to perform the corresponding setup on TRGMII hardware module. Signed-off-by:
Sean Wang <sean.wang@mediatek.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Merge tag 'rxrpc-rewrite-20160922-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs David Howells says: ==================== rxrpc: Preparation for slow-start algorithm [ver #2] Here are some patches that prepare for improvements in ACK generation and for the implementation of the slow-start part of the protocol: (1) Stop storing the protocol header in the Tx socket buffers, but rather generate it on the fly. This potentially saves a little space and makes it easier to alter the header just before transmission (the flags may get altered and the serial number has to be changed). (2) Mask off the Tx buffer annotations and add a flag to record which ones have already been resent. (3) Track RTT on a per-peer basis for use in future changes. Tracepoints are added to log this. (4) Send PING ACKs in response to incoming calls to elicit a PING-RESPONSE ACK from which RTT data can be calculated. The response also carries other useful information. (5) Expedite PING-RESPONSE ACK generation from sendmsg. If we're actively using sendmsg, this allows us, under some circumstances, to avoid having to rely on the background work item to run to generate this ACK. This requires ktime_sub_ms() to be added. (6) Set the REQUEST-ACK flag on some DATA packets to elicit ACK-REQUESTED ACKs from which RTT data can be calculated. (7) Limit the use of pings and ACK requests for RTT determination. Changes: (V2) Don't use the C division operator for 64-bit division. One instance should use do_div() and the other should be using nsecs_to_jiffies(). The last two patches got transposed, leading to an undefined symbol in one of them. Reported-by:
kbuild test robot <lkp@intel.com> ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David Howells authored
We don't want to send a PING ACK for every new incoming call as that just adds to the network traffic. Instead, we send a PING ACK to the first three that we receive and then once per second thereafter. This could probably be made adjustable in future. Signed-off-by:
David Howells <dhowells@redhat.com>
-
David Howells authored
Reduce the number of ACK-Requests we set on DATA packets that we're sending to reduce network traffic. We set the flag on odd-numbered DATA packets to start off the RTT cache until we have at least three entries in it and then probe once per second thereafter to keep it topped up. This could be made tunable in future. Note that from this point, the RXRPC_REQUEST_ACK flag is set on DATA packets as we transmit them and not stored statically in the sk_buff. Signed-off-by:
David Howells <dhowells@redhat.com>
-
Yuchung Cheng authored
Since the TFO socket is accepted right off SYN-data, the socket owner can call getsockopt(TCP_INFO) to collect ongoing SYN-ACK retransmission or timeout stats (i.e., tcpi_total_retrans, tcpi_retransmits). Currently those stats are only updated upon handshake completes. This patch fixes it. Signed-off-by:
Yuchung Cheng <ycheng@google.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
Neal Cardwell <ncardwell@google.com> Signed-off-by:
Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Yuchung Cheng authored
This patch fixes these under-accounting SNMP rtx stats LINUX_MIB_TCPFORWARDRETRANS LINUX_MIB_TCPFASTRETRANS LINUX_MIB_TCPSLOWSTARTRETRANS when retransmitting TSO packets Fixes: 10d3be56 ("tcp-tso: do not split TSO packets at retransmit time") Signed-off-by:
Yuchung Cheng <ycheng@google.com> Acked-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Joel Stanley says: ==================== ftgmac100 support for ast2500 This series adds support to the ftgmac100 driver for the Aspeed ast2400 and ast2500 SoCs. In particular, they ensure the driver works correctly on the ast2500 where the MAC block has seen some changes in register layout. They have been tested on ast2400 and ast2500 systems with the NCSI stack and with a directly attached PHY. V2 reworks the two patches relating to PHYSTS_CHG into the one patch that disables the interrupt instead of playing with interrupt sensitivity. I kept patch 4 'net/faraday: Clear stale interrupts' which was first introduced to clear the stale PHYSTS_CHG interrupt, as it helps keep us safe from unhygienic (vendor) bootloaders. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Joel Stanley authored
The PHYSTS_CHG (the ftgmac100's PHY IRQ) is telling the system to go look at the PHY registers for a link status change. The interrupt was causing issues on Aspeed SoC where some board designs had an active high configuration, some active low, and in some cases repurposed for other functions. When misconfigured Linux would chew 100% of CPU cycles servicing interrupts: [ 20.280000] ftgmac100 1e660000.ethernet eth0: [ISR] = 0x200: PHYSTS_CHG [ 20.280000] ftgmac100 1e660000.ethernet eth0: [ISR] = 0x200: PHYSTS_CHG [ 20.280000] ftgmac100 1e660000.ethernet eth0: [ISR] = 0x200: PHYSTS_CHG [ 20.300000] ftgmac100 1e660000.ethernet eth0: [ISR] = 0x200: PHYSTS_CHG While in the ftgmac100 IP can be configured for high, low and edge sensitivity the current driver always polls the PHY, so we chose to mask out the interrupt. See https://patchwork.ozlabs.org/patch/672099/ for more discussion. Signed-off-by:
Joel Stanley <joel@jms.id.au> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Joel Stanley authored
The Aspeed SoCs have a new MDIO interface as an option in the G4 and G5 SoCs. The old one is still available, so select it in order to remain compatible with the ftgmac100 driver. Signed-off-by:
Joel Stanley <joel@jms.id.au> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Gavin Shan authored
There is stale interrupt (PHYSTS_CHG in ISR, bit#6 in 0x0) from the bootloader (uboot) when enabling the MAC. The stale interrupts aren't part of kernel and should be cleared. This clears the stale interrupts in ISR (0x0) when enabling the MAC. Signed-off-by:
Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by:
Joel Stanley <joel@jms.id.au> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Joel Stanley authored
The RXDES and TXDES registers bits in the ftgmac100 indicates EDO{R,T}R at bit position 15 for the Faraday Tech IP. However, the version of this IP present in the Aspeed SoCs has these bits at position 30 in the registers. It appers that ast2400 SoCs support both positions, with the 15th bit marked as reserved but still functional. In the ast2500 this bit is reused for another function, so we need a work around. This was confirmed with engineers from Aspeed that using bit 30 is correct for both the ast2400 and ast2500 SoCs. Signed-off-by:
Joel Stanley <joel@jms.id.au> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Andrew Jeffery authored
These bits are #defined at a fixed location. In order to support future hardware that has chosen to move these bits around move the bits into a member of the struct ftgmac100. Signed-off-by:
Andrew Jeffery <andrew@aj.id.au> Signed-off-by:
Joel Stanley <joel@jms.id.au> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Andrew Jeffery authored
The ftgmac100 hardware revision in e.g. the Aspeed AST2500 no longer reserves all bits in RXDES#2 but instead uses the bottom 16 bits to store MAC frame metadata. Avoid corruption by shifting struct page pointers out to their own member in struct ftgmac100. Signed-off-by:
Andrew Jeffery <andrew@aj.id.au> Signed-off-by:
Joel Stanley <joel@jms.id.au> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David Howells authored
In addition to sending a PING ACK to gain RTT data, we can set the RXRPC_REQUEST_ACK flag on a DATA packet and get a REQUESTED-ACK ACK. The ACK packet contains the serial number of the packet it is in response to, so we can look through the Tx buffer for a matching DATA packet. This requires that the data packets be stamped with the time of transmission as a ktime rather than having the resend_at time in jiffies. This further requires the resend code to do the resend determination in ktimes and convert to jiffies to set the timer. Signed-off-by:
David Howells <dhowells@redhat.com>
-
David Howells authored
Add a ktime_sub_ms() to go with ktime_add_ms() and co. for use in AF_RXRPC RTT determination. Signed-off-by:
David Howells <dhowells@redhat.com>
-
David Howells authored
Expedite the transmission of a response to a PING ACK by sending it from sendmsg if one is pending. We're most likely to see a PING ACK during the client call Tx phase as the other side may use it to determine a number of parameters, such as the client's receive window size, the RTT and whether the client is doing slow start (similar to RFC5681). If we don't expedite it, it's left to the background processing thread to transmit. Signed-off-by:
David Howells <dhowells@redhat.com>
-
David Howells authored
Send a PING ACK packet to the peer when we get a new incoming call from a peer we don't have a record for. The PING RESPONSE ACK packet will tell us the following about the peer: (1) its receive window size (2) its MTU sizes (3) its support for jumbo DATA packets (4) if it supports slow start (similar to RFC 5681) (5) an estimate of the RTT This is necessary because the peer won't normally send us an ACK until it gets to the Rx phase and we send it a packet, but we would like to know some of this information before we start sending packets. A pair of tracepoints are added so that RTT determination can be observed. Signed-off-by:
David Howells <dhowells@redhat.com>
-
Wei Yongjun authored
Remove an open coded simple_open() function and replace file operations references to the function with simple_open() instead. Generated by: scripts/coccinelle/api/simple_open.cocci Signed-off-by:
Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Wei Yongjun authored
mdio_module_driver() makes the code simpler by eliminating boilerplate code. Signed-off-by:
Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-