- 17 Apr, 2015 40 commits
-
-
Tony Luck authored
[ Upstream commit f7cf2a22 ] Haswell moved the TOLM/TOHM registers to a different device and offset. The sb_edac driver accounted for the change of device, but not for the new offset. There was also a typo in the constant to fill in the low 26 bits (was 0x1ffffff, should be 0x3ffffff). This resulted in a bogus value for the top of low memory: EDAC DEBUG: get_memory_layout: TOLM: 0.032 GB (0x0000000001ffffff) which would result in EDAC refusing to translate addresses for errors above the bogus value and below 4GB: sbridge MC3: HANDLING MCE MEMORY ERROR sbridge MC3: CPU 0: Machine Check Event: 0 Bank 7: 8c00004000010090 sbridge MC3: TSC 0 sbridge MC3: ADDR 2000000 sbridge MC3: MISC 523eac86 sbridge MC3: PROCESSOR 0:306f3 TIME 1414600951 SOCKET 0 APIC 0 MC3: 1 CE Error at TOLM area, on addr 0x02000000 on any memory ( page:0x0 offset:0x0 grain:32 syndrome:0x0) With the fix we see the correct TOLM value: DEBUG: get_memory_layout: TOLM: 2.048 GB (0x000000007fffffff) and we decode address 2000000 correctly: sbridge MC3: HANDLING MCE MEMORY ERROR sbridge MC3: CPU 0: Machine Check Event: 0 Bank 7: 8c00004000010090 sbridge MC3: TSC 0 sbridge MC3: ADDR 2000000 sbridge MC3: MISC 523e1086 sbridge MC3: PROCESSOR 0:306f3 TIME 1414601319 SOCKET 0 APIC 0 DEBUG: get_memory_error_data: SAD interleave package: 0 = CPU socket 0, HA 0, shiftup: 0 DEBUG: get_memory_error_data: TAD#0: address 0x0000000002000000 < 0x000000007fffffff, socket interleave 1, channel interleave 4 (offset 0x00000000), index 0, base ch: 0, ch mask: 0x01 DEBUG: get_memory_error_data: RIR#0, limit: 4.095 GB (0x00000000ffffffff), way: 1 DEBUG: get_memory_error_data: RIR#0: channel address 0x00200000 < 0xffffffff, RIR interleave 0, index 0 DEBUG: sbridge_mce_output_error: area:DRAM err_code:0001:0090 socket:0 channel_mask:1 rank:0 MC3: 1 CE memory read error on CPU_SrcID#0_Channel#0_DIMM#0 (channel:0 slot:0 page:0x2000 offset:0x0 grain:32 syndrome:0x0 - area:DRAM err_code:0001:0090 socket:0 channel_mask:1 rank:0) Signed-off-by:
Tony Luck <tony.luck@intel.com> Acked-by:
Aristeu Rozanski <aris@redhat.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
Sasha Levin <sasha.levin@oracle.com>
-
Ilya Dryomov authored
[ Upstream commit 6d7fdb0a ] This reverts commit 89baaa57. Dirty page throttling should be sufficient for us in the general case so there is no need to use __GFP_MEMALLOC - it would be needed only in the swap-over-rbd case, which we currently don't support. (It would probably take approximately the commit that is being reverted to add that support, but we would also need the "swap" option to distinguish from the general case and make sure swap ceph_client-s aren't shared with anything else.) See ceph-devel threads [1] and [2] for the details of why enabling pfmemalloc reserves for all cases is a bad thing. On top of potential system lockups related to drained emergency reserves, this turned out to cause ceph lockups in case peers are on the same host and communicating via loopback due to sk_filter() dropping pfmemalloc skbs on the receiving side because the receiving loopback socket is not tagged with SOCK_MEMALLOC. [1] "SOCK_MEMALLOC vs loopback" http://www.spinics.net/lists/ceph-devel/msg22998.html [2] "[PATCH] libceph: don't set memalloc flags in loopback case" http://www.spinics.net/lists/ceph-devel/msg23392.html Conflicts: net/ceph/messenger.c [ context: tcp_nodelay option ] Cc: Mike Christie <michaelc@cs.wisc.edu> Cc: Mel Gorman <mgorman@suse.de> Cc: Sage Weil <sage@redhat.com> Cc: stable@vger.kernel.org # 3.18+, needs backporting Signed-off-by:
Ilya Dryomov <idryomov@gmail.com> Acked-by:
Mike Christie <michaelc@cs.wisc.edu> Acked-by:
Mel Gorman <mgorman@suse.de> [idryomov@gmail.com: backport to 3.18, 3.19: context] Signed-off-by:
-
Sergei Antonov authored
[ Upstream commit 98cf21c6 ] Fix B-tree corruption when a new record is inserted at position 0 in the node in hfs_brec_insert(). In this case a hfs_brec_update_parent() is called to update the parent index node (if exists) and it is passed hfs_find_data with a search_key containing a newly inserted key instead of the key to be updated. This results in an inconsistent index node. The bug reproduces on my machine after an extents overflow record for the catalog file (CNID=4) is inserted into the extents overflow B-tree. Because of a low (reserved) value of CNID=4, it has to become the first record in the first leaf node. The resulting first leaf node is correct: ---------------------------------------------------- | key0.CNID=4 | key1.CNID=123 | key2.CNID=456, ... | ---------------------------------------------------- But the parent index key0 still contains the previous key CNID=123: ----------------------- | key0.CNID=123 | ... | ----------------------- A change in hfs_brec_insert() makes hfs_brec_update_parent() work correctly by preventing it from getting fd->record=-1 value from __hfs_brec_find(). Along the way, I removed duplicate code with unification of the if condition. The resulting code is equivalent to the original code because node is never 0. Also hfs_brec_update_parent() will now return an error after getting a negative fd->record value. However, the return value of hfs_brec_update_parent() is not checked anywhere in the file and I'm leaving it unchanged by this patch. brec.c lacks error checking after some other calls too, but this issue is of less importance than the one being fixed by this patch. Signed-off-by:
Sergei Antonov <saproj@gmail.com> Cc: Joe Perches <joe@perches.com> Reviewed-by:
Vyacheslav Dubeyko <slava@dubeyko.com> Acked-by:
Hin-Tak Leung <htl10@users.sourceforge.net> Cc: Anton Altaparmakov <aia21@cam.ac.uk> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Christoph Hellwig <hch@infradead.org> Cc: <stable@vger.kernel.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Uwe Kleine-König authored
[ Upstream commit 391949b6 ] With spidev the mesg->complete callback points to spidev_complete. Calling this unblocks spidev_sync and so spidev_sync_write finishes. As the struct spi_message just read is a local variable in spidev_sync_write and recording the trace event accesses this message the recording is better done first. The same can happen for spidev_sync_read. This fixes an oops observed on a 3.14-rt system with spidev activity after echo 1 > /sys/kernel/debug/tracing/events/spi/enable . Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by:
-
Ivan T. Ivanov authored
[ Upstream commit 12cb89e3 ] num-cs is 32 bit property, don't read just upper 16 bits. Fixes: 4a8573ab (spi: qup: Remove chip select function) Signed-off-by:
Ivan T. Ivanov <iivanov@mm-sol.com> Signed-off-by:
-
Mikulas Patocka authored
[ Upstream commit 09ee96b2 ] The "dm snapshot: suspend origin when doing exception handover" commit fixed a exception store handover bug associated with pending exceptions to the "snapshot-origin" target. However, a similar problem exists in snapshot merging. When snapshot merging is in progress, we use the target "snapshot-merge" instead of "snapshot-origin". Consequently, during exception store handover, we must find the snapshot-merge target and suspend its associated mapped_device. To avoid lockdep warnings, the target must be suspended and resumed without holding _origins_lock. Introduce a dm_hold() function that grabs a reference on a mapped_device, but unlike dm_get(), it doesn't crash if the device has the DMF_FREEING flag set, it returns an error in this case. In snapshot_resume() we grab the reference to the origin device using dm_hold() while holding _origins_lock (_origins_lock guarantees that the device won't disappear). Then we release _origins_lock, suspend the device and grab _origins_lock again. NOTE to stable@ people: When backporting to kernels 3.18 and older, use dm_internal_suspend and dm_internal_resume instead of dm_internal_suspend_fast and dm_internal_resume_fast. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Mikulas Patocka authored
[ Upstream commit b735fede ] In the function snapshot_resume we perform exception store handover. If there is another active snapshot target, the exception store is moved from this target to the target that is being resumed. The problem is that if there is some pending exception, it will point to an incorrect exception store after that handover, causing a crash due to dm-snap-persistent.c:get_exception()'s BUG_ON. This bug can be triggered by repeatedly changing snapshot permissions with "lvchange -p r" and "lvchange -p rw" while there are writes on the associated origin device. To fix this bug, we must suspend the origin device when doing the exception store handover to make sure that there are no pending exceptions: - introduce _origin_hash that keeps track of dm_origin structures. - introduce functions __lookup_dm_origin, __insert_dm_origin and __remove_dm_origin that manipulate the origin hash. - modify snapshot_resume so that it calls dm_internal_suspend_fast() and dm_internal_resume_fast() on the origin device. NOTE to stable@ people: When backporting to kernels 3.12-3.18, use dm_internal_suspend and dm_internal_resume instead of dm_internal_suspend_fast and dm_internal_resume_fast. When backporting to kernels older than 3.12, you need to pick functions dm_internal_suspend and dm_internal_resume from the commit fd2ed4d2. Signed-off-by:
-
Sasha Levin authored
[ Upstream commit 5f027a3b ] It was always intended that a read to an unprovisioned block will return zeroes regardless of whether the pool is in read-only or read-write mode. thin_bio_map() was inconsistent with its handling of such reads when the pool is in read-only mode, it now properly zero-fills the bios it returns in response to unprovisioned block reads. Eliminate thin_bio_map()'s special read-only mode handling of -ENODATA and just allow the IO to be deferred to the worker which will result in pool->process_bio() handling the IO (which already properly zero-fills reads to unprovisioned blocks). Reported-by:
Eric Sandeen <sandeen@redhat.com> Signed-off-by:
Joe Thornber <ejt@redhat.com> Signed-off-by:
-
Darrick J. Wong authored
[ Upstream commit e5db2980 ] Since it's possible for the discard and write same queue limits to change while the upper level command is being sliced and diced, fix up both of them (a) to reject IO if the special command is unsupported at the start of the function and (b) read the limits once and let the commands error out on their own if the status happens to change. Signed-off-by:
Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by:
-
Mikulas Patocka authored
[ Upstream commit ab7c7bb6 ] __dm_destroy() must take the suspend_lock so that its presuspend and postsuspend calls do not race with an internal suspend. Signed-off-by:
-
Andy Shevchenko authored
[ Upstream commit a104a45b ] The commit 9cade1a4 (dma: dw: split driver to library part and platform code) introduced a separate platform driver but missed to add a MODULE_ALIAS("platform:dw_dmac"); to that module. The patch adds this to get driver loaded automatically if platform device is registered. Reported-by:
"Blin, Jerome" <jerome.blin@intel.com> Fixes: 9cade1a4 (dma: dw: split driver to library part and platform code) Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
Malcolm Priestley authored
[ Upstream commit 40c8790b ] When the driver sets this rate a power of zero value is set causing data flow stoppage until another rate is tried. Signed-off-by:
Malcolm Priestley <tvboxspy@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Malcolm Priestley authored
[ Upstream commit 163fe301 ] When the driver sets this rate a power of zero value is set causing data flow stoppage until another rate is tried. Signed-off-by:
-
Peter Zijlstra authored
[ Upstream commit d525211f ] Vince reported a watchdog lockup like: [<ffffffff8115e114>] perf_tp_event+0xc4/0x210 [<ffffffff810b4f8a>] perf_trace_lock+0x12a/0x160 [<ffffffff810b7f10>] lock_release+0x130/0x260 [<ffffffff816c7474>] _raw_spin_unlock_irqrestore+0x24/0x40 [<ffffffff8107bb4d>] do_send_sig_info+0x5d/0x80 [<ffffffff811f69df>] send_sigio_to_task+0x12f/0x1a0 [<ffffffff811f71ce>] send_sigio+0xae/0x100 [<ffffffff811f72b7>] kill_fasync+0x97/0xf0 [<ffffffff8115d0b4>] perf_event_wakeup+0xd4/0xf0 [<ffffffff8115d103>] perf_pending_event+0x33/0x60 [<ffffffff8114e3fc>] irq_work_run_list+0x4c/0x80 [<ffffffff8114e448>] irq_work_run+0x18/0x40 [<ffffffff810196af>] smp_trace_irq_work_interrupt+0x3f/0xc0 [<ffffffff816c99bd>] trace_irq_work_interrupt+0x6d/0x80 Which is caused by an irq_work generating new irq_work and therefore not allowing forward progress. This happens because processing the perf irq_work triggers another perf event (tracepoint stuff) which in turn generates an irq_work ad infinitum. Avoid this by raising the recursion counter in the irq_work -- which effectively disables all software events (including tracepoints) from actually triggering again. Reported-by:
Vince Weaver <vincent.weaver@maine.edu> Tested-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: <stable@vger.kernel.org> Link: http://lkml.kernel.org/r/20150219170311.GH21418@twins.programming.kicks-ass.netSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Laurent Pinchart authored
[ Upstream commit d7c14605 ] The error code paths that require cleanup use a goto to jump to the cleanup code and return an error code. However, the error code variable res, which is initialized to -EINVAL when declared, is then overwritten with the return value of of_parse_phandle_with_args(), and reused as the return code from of_irq_parse_one(). This leads to an undetermined error being returned instead of the expected -EINVAL value. Fix it. Signed-off-by:
Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Cc: stable@vger.kernel.org # 3.13+ Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Gregory CLEMENT authored
[ Upstream commit 43b68879 ] As stated in kernel/cpu_pm.c, "Platform is responsible for ensuring that cpu_pm_enter is not called twice on the same CPU before cpu_pm_exit is called.". In the current code in case of failure when calling mvebu_v7_cpu_suspend, the function cpu_pm_exit() is never called whereas cpu_pm_enter() was called just before. This patch moves the cpu_pm_exit() in order to balance the cpu_pm_enter() calls. Cc: stable@vger.kernel.org Reported-by:
Fulvio Benini <fbf@libero.it> Signed-off-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by:
Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by:
-
Larry Finger authored
[ Upstream commit c8f03455 ] Routine rtl_is_special_data() is supposed to identify packets that need to use a low bit rate so that the probability of successful transmission is high. The current version has a bug that causes all IPv6 packets to be labelled as special, with a corresponding low rate of transmission. A complete fix will be quite intrusive, but until that is available, all IPv6 packets are identified as regular. This patch also removes a magic number. Reported-and-tested-by:
Alan Fisher <acf@unixcube.org> Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> [3.18+] Cc: Alan Fisher <acf@unixcube.org> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Thierry Reding authored
[ Upstream commit 2f1bce48 ] devm_phy_create() stores the pointer to the new PHY at the address returned by devres_alloc(). The res parameter passed to devm_phy_match() is therefore the location where the pointer to the PHY is stored, hence it needs to be dereferenced before comparing to the match data in order to find the correct match. Cc: <stable@vger.kernel.org> # v3.13+ Signed-off-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by:
-
Peter Chen authored
[ Upstream commit a886bd92 ] We should signal connect (pull up dp) after we have already at peripheral mode, otherwise, the dp may be toggled due to we reset controller or do disconnect during the initialization for peripheral, then, the host may be confused during the enumeration, eg, it finds the reset can't succeed, but the device is still there, see below error message. hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad? hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad? hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad? hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad? hub 1-0:1.0: unable to enumerate USB device on port 1 Fixes: the issue existed when the otg fsm code was added. Cc: <stable@vger.kernel.org> # v3.16+ Signed-off-by:
Peter Chen <peter.chen@freescale.com> Signed-off-by:
-
Li Jun authored
[ Upstream commit d20f7807 ] This patch adds response to a_alt_hnp_support set feature request from legacy A device, that is, B-device can provide a message to the user indicating that the user needs to connect the B-device to an alternate port on the A-device. A device sets this feature indicates to the B-device that it is connected to an A-device port that is not capable of HNP, but that the A-device does have an alternate port that is capable of HNP. [Peter] Without this patch, the OTG B device can't be enumerated on non-HNP port at A device, see below log: [ 2.287464] usb 1-1: Dual-Role OTG device on non-HNP port [ 2.293105] usb 1-1: can't set HNP mode: -32 [ 2.417422] usb 1-1: new high-speed USB device number 4 using ci_hdrc [ 2.460635] usb 1-1: Dual-Role OTG device on non-HNP port [ 2.466424] usb 1-1: can't set HNP mode: -32 [ 2.587464] usb 1-1: new high-speed USB device number 5 using ci_hdrc [ 2.630649] usb 1-1: Dual-Role OTG device on non-HNP port [ 2.636436] usb 1-1: can't set HNP mode: -32 [ 2.641003] usb usb1-port1: unable to enumerate USB device Cc: stable <stable@vger.kernel.org> Acked-by:
Li Jun <b47624@freescale.com> Signed-off-by:
-
David Dueck authored
[ Upstream commit d0f347d6 ] This fixes a potential null pointer dereference. Cc: <stable@vger.kernel.org> # v3.16+ Fixes: d4332013 ("driver core: dev_get_drvdata: Don't check for NULL dev") Acked-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
David Dueck <davidcdueck@googlemail.com> Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
Hans de Goede authored
[ Upstream commit bda13e35 ] A new uas compatible controller has shown up in some people's devices from the manufacturer Initio Corporation, this controller needs the US_FL_NO_ATA_1X quirk to work properly with uas, so add it to the uas quirks table. Reported-and-tested-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com> Cc: stable@vger.kernel.org # 3.16 Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Andrei Otcheretianski authored
[ Upstream commit 0f611d28 ] Since moving the interface combination checks to mac80211, it's broken because it now only considers interfaces with an assigned channel context, so for example any interface that isn't active can still be up, which is clearly an issue; also, in particular P2P-Device wdevs are an issue since they never have a chanctx. Fix this by counting running interfaces instead the ones with a channel context assigned. Cc: stable@vger.kernel.org [3.16+] Fixes: 73de86a3 ("cfg80211/mac80211: move interface counting for combination check to mac80211") Signed-off-by:
Andrei Otcheretianski <andrei.otcheretianski@intel.com> Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> [rewrite commit message, dig out the commit it fixes] Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Bob Copeland authored
[ Upstream commit d0c22119 ] The mesh forwarding path was not checking that data frames were protected when running an encrypted network; add the necessary check. Cc: stable@vger.kernel.org Reported-by:
Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
Bob Copeland <me@bobcopeland.com> Signed-off-by:
-
Michal Kazior authored
[ Upstream commit aa75ebc2 ] Some APs experience problems when working with U-APSD. Decreasing the probability of that happening by using legacy mode for all ACs but VO isn't enough. Cisco 4410N originally forced us to enable VO by default only because it treated non-VO ACs as legacy. However some APs (notably Netgear R7000) silently reclassify packets to different ACs. Since u-APSD ACs require trigger frames for frame retrieval clients would never see some frames (e.g. ARP responses) or would fetch them accidentally after a long time. It makes little sense to enable u-APSD queues by default because it needs userspace applications to be aware of it to actually take advantage of the possible additional powersavings. Implicitly depending on driver autotrigger frame support doesn't make much sense. Cc: stable@vger.kernel.org Signed-off-by:
Michal Kazior <michal.kazior@tieto.com> Signed-off-by:
-
Johannes Berg authored
[ Upstream commit 496fcc29 ] As HT/VHT depend heavily on QoS/WMM, it's not a good idea to let userspace add clients that have HT/VHT but not QoS/WMM. Since it does so in certain cases we've observed (client is using HT IEs but not QoS/WMM) just ignore the HT/VHT info at this point and don't pass it down to the drivers which might unconditionally use it. Cc: stable@vger.kernel.org Signed-off-by:
-
Benjamin Tissoires authored
[ Upstream commit b57a7128 ] The board id capability has been added in firmware 7.5. Cc: stable@vger.kernel.org Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Benjamin Tissoires authored
[ Upstream commit ebc80840 ] The Fimware 8.1 has a bug in which the extra buttons are only sent when the ExtBit is 1. This should be fixed in a future FW update which should have a bump of the minor version. Cc: stable@vger.kernel.org Signed-off-by:
-
Dmitry Torokhov authored
[ Upstream commit dc5465dc ] On the X1 Carbon 3rd gen (with a 2015 broadwell cpu), the physical middle button of the trackstick (attached to the touchpad serio device, of course) seems to get lost. Actually, the touchpads reports 3 extra buttons, which falls in the switch below to the '2' case. Let's handle the case of odd numbers also, so that the middle button finds its way back. Cc: stable@vger.kernel.org Signed-off-by:
-
Benjamin Tissoires authored
[ Upstream commit 02e07492 ] Post-2013 Lenovo laptops provide correct min/max dimensions, which are different with the ones currently quirked. According to https://bugzilla.kernel.org/show_bug.cgi?id=91541 the following board ids are assigned in the post-2013 touchpads: t440p/t440s: LEN0036 -> 2964/2962 t540p: LEN0034 -> 2964 Using 2961 as the common minimum makes these 3 laptops OK. We may need to update those values later if other pnp_ids has a lower board_id. Cc: stable@vger.kernel.org Signed-off-by:
-
Daniel Martin authored
[ Upstream commit 5b3089dd ] Add a min/max range for board ids to the min/max coordinates quirk. This makes it possible to restrict quirks to specific models based upon their board id. The define ANY_BOARD_ID (0) serves as a wild card. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=91541 Cc: stable@vger.kernel.org Signed-off-by:
Daniel Martin <daniel.martin@secunet.com> Acked-by:
-
Daniel Martin authored
[ Upstream commit b05f4d1c ] The firmware of the X240 (LEN0035, 2013/12) exposes the same values x [1232..5710], y [1156..4696] as the quirk applies. Cc: stable@vger.kernel.org Signed-off-by:
Daniel Martin <consume.noise@gmail.com> Acked-by:
-
Daniel Martin authored
[ Upstream commit ac097930 ] Query the min dimensions even if the check SYN_EXT_CAP_REQUESTS(priv->capabilities) >= 7 fails, but we know that the firmware version 8.1 is safe. With that we don't need quirks for post-2013 models anymore as they expose correct min and max dimensions. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=91541 Cc: stable@vger.kernel.org Signed-off-by:
-
Daniel Martin authored
[ Upstream commit 9aff6598 ] Logging the dimension values we queried and the values we use from a quirk to overwrite can be helpful for debugging. This partly relates to bug: https://bugzilla.kernel.org/show_bug.cgi?id=91541 Cc: stable@vger.kernel.org Signed-off-by:
-
Daniel Martin authored
[ Upstream commit 8b04baba ] Split the function synaptics_resolution() into synaptics_resolution() and synaptics_quirks(). synaptics_resolution() will be called before synaptics_quirks() to query dimensions and resolutions before overwriting them with quirks. Cc: stable@vger.kernel.org Signed-off-by:
-
Bart Van Assche authored
[ Upstream commit 75c3d0bf ] This patch fixes the incorrect use of __transport_register_session() in tcm_qla2xxx_check_initiator_node_acl() code, that does not perform explicit se_tpg->session_lock when accessing se_tpg->tpg_sess_list to add new se_sess nodes. Given that tcm_qla2xxx_check_initiator_node_acl() is not called with qla_hw->hardware_lock held for all accesses of ->tpg_sess_list, the code should be using transport_register_session() instead. Signed-off-by:
Bart Van Assche <bart.vanassche@sandisk.com> Cc: Giridhar Malavali <giridhar.malavali@qlogic.com> Cc: Quinn Tran <quinn.tran@qlogic.com> Cc: <stable@vger.kernel.org> # 3.5+ Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit d556546e ] This patch adds a missing set of conditional check braces in ft_invl_hw_context() originally introduced by commit dcd998cc when handling DDP failures in ft_recv_write_data() code. commit dcd998cc Author: Kiran Patil <kiran.patil@intel.com> Date: Wed Aug 3 09:20:01 2011 +0000 tcm_fc: Handle DDP/SW fc_frame_payload_get failures in ft_recv_write_data Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Cc: Kiran Patil <kiran.patil@intel.com> Cc: <stable@vger.kernel.org> # 3.1+ Signed-off-by:
-
Yongbae Park authored
[ Upstream commit 7b8f10da ] The initialisation of the efm32 clocksource first sets up the irq and only after that initialises the data needed for irq handling. In case this initialisation is delayed the irq handler would dereference a NULL pointer. I'm not aware of anything that could delay the process in such a way, but it's better to be safe than sorry, so setup the irq only when the clock event device is ready. Cc: stable@vger.kernel.org Acked-by:
Yongbae Park <yongbae2@gmail.com> Signed-off-by:
-
Philipp Zabel authored
[ Upstream commit c6b570d9 ] This patch fixes a NULL pointer dereference when enabling regmap event tracing in the presence of a syscon regmap, introduced by commit bdb0066d ("mfd: syscon: Decouple syscon interface from platform devices"). That patch introduced syscon regmaps that have their dev field set to NULL. The regmap trace events expect it to point to a valid struct device and feed it to dev_name(): $ echo 1 > /sys/kernel/debug/tracing/events/regmap/enable Unable to handle kernel NULL pointer dereference at virtual address 0000002c pgd = 80004000 [0000002c] *pgd=00000000 Internal error: Oops: 17 [#1] SMP ARM Modules linked in: coda videobuf2_vmalloc CPU: 0 PID: 304 Comm: kworker/0:2 Not tainted 4.0.0-rc2+ #9197 Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) Workqueue: events_freezable thermal_zone_device_check task: 9f25a200 ti: 9f1ee000 task.ti: 9f1ee000 PC is at ftrace_raw_event_regmap_block+0x3c/0xe4 LR is at _regmap_raw_read+0x1bc/0x1cc pc : [<803636e8>] lr : [<80365f2c>] psr: 600f0093 sp : 9f1efd78 ip : 9f1efdb8 fp : 9f1efdb4 r10: 00000004 r9 : 00000001 r8 : 00000001 r7 : 00000180 r6 : 00000000 r5 : 9f00e3c0 r4 : 00000003 r3 : 00000001 r2 : 00000180 r1 : 00000000 r0 : 9f00e3c0 Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel Control: 10c5387d Table: 2d91004a DAC: 00000015 Process kworker/0:2 (pid: 304, stack limit = 0x9f1ee210) Stack: (0x9f1efd78 to 0x9f1f0000) fd60: 9f1efda4 9f1efd88 fd80: 800708c0 805f9510 80927140 800f0013 9f1fc800 9eb2f490 00000000 00000180 fda0: 808e3840 00000001 9f1efdfc 9f1efdb8 80365f2c 803636b8 805f8958 800708e0 fdc0: a00f0013 803636ac 9f16de00 00000180 80927140 9f1fc800 9f1fc800 9f1efe6c fde0: 9f1efe6c 9f732400 00000000 00000000 9f1efe1c 9f1efe00 80365f70 80365d7c fe00: 80365f3c 9f1fc800 9f1fc800 00000180 9f1efe44 9f1efe20 803656a4 80365f48 fe20: 9f1fc800 00000180 9f1efe6c 9f1efe6c 9f732400 00000000 9f1efe64 9f1efe48 fe40: 803657bc 80365634 00000001 9e95f910 9f1fc800 9f1efeb4 9f1efe8c 9f1efe68 fe60: 80452ac0 80365778 9f1efe8c 9f1efe78 9e93d400 9e93d5e8 9f1efeb4 9f72ef40 fe80: 9f1efeac 9f1efe90 8044e11c 80452998 8045298c 9e93d608 9e93d400 808e1978 fea0: 9f1efecc 9f1efeb0 8044fd14 8044e0d0 ffffffff 9f25a200 9e93d608 9e481380 fec0: 9f1efedc 9f1efed0 8044fde8 8044fcec 9f1eff1c 9f1efee0 80038d50 8044fdd8 fee0: 9f1ee020 9f72ef40 9e481398 00000000 00000008 9f72ef54 9f1ee020 9f72ef40 ff00: 9e481398 9e481380 00000008 9f72ef40 9f1eff5c 9f1eff20 80039754 80038bfc ff20: 00000000 9e481380 80894100 808e1662 00000000 9e4f2ec0 00000000 9e481380 ff40: 800396f8 00000000 00000000 00000000 9f1effac 9f1eff60 8003e020 80039704 ff60: ffffffff 00000000 ffffffff 9e481380 00000000 00000000 9f1eff78 9f1eff78 ff80: 00000000 00000000 9f1eff88 9f1eff88 9e4f2ec0 8003df30 00000000 00000000 ffa0: 00000000 9f1effb0 8000eb60 8003df3c 00000000 00000000 00000000 00000000 ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 ffe0: 00000000 00000000 00000000 00000000 00000013 00000000 ffffffff ffffffff Backtrace: [<803636ac>] (ftrace_raw_event_regmap_block) from [<80365f2c>] (_regmap_raw_read+0x1bc/0x1cc) r9:00000001 r8:808e3840 r7:00000180 r6:00000000 r5:9eb2f490 r4:9f1fc800 [<80365d70>] (_regmap_raw_read) from [<80365f70>] (_regmap_bus_read+0x34/0x6c) r10:00000000 r9:00000000 r8:9f732400 r7:9f1efe6c r6:9f1efe6c r5:9f1fc800 r4:9f1fc800 [<80365f3c>] (_regmap_bus_read) from [<803656a4>] (_regmap_read+0x7c/0x144) r6:00000180 r5:9f1fc800 r4:9f1fc800 r3:80365f3c [<80365628>] (_regmap_read) from [<803657bc>] (regmap_read+0x50/0x70) r9:00000000 r8:9f732400 r7:9f1efe6c r6:9f1efe6c r5:00000180 r4:9f1fc800 [<8036576c>] (regmap_read) from [<80452ac0>] (imx_get_temp+0x134/0x1a4) r6:9f1efeb4 r5:9f1fc800 r4:9e95f910 r3:00000001 [<8045298c>] (imx_get_temp) from [<8044e11c>] (thermal_zone_get_temp+0x58/0x74) r7:9f72ef40 r6:9f1efeb4 r5:9e93d5e8 r4:9e93d400 [<8044e0c4>] (thermal_zone_get_temp) from [<8044fd14>] (thermal_zone_device_update+0x34/0xec) r6:808e1978 r5:9e93d400 r4:9e93d608 r3:8045298c [<8044fce0>] (thermal_zone_device_update) from [<8044fde8>] (thermal_zone_device_check+0x1c/0x20) r5:9e481380 r4:9e93d608 [<8044fdcc>] (thermal_zone_device_check) from [<80038d50>] (process_one_work+0x160/0x3d4) [<80038bf0>] (process_one_work) from [<80039754>] (worker_thread+0x5c/0x4f4) r10:9f72ef40 r9:00000008 r8:9e481380 r7:9e481398 r6:9f72ef40 r5:9f1ee020 r4:9f72ef54 [<800396f8>] (worker_thread) from [<8003e020>] (kthread+0xf0/0x108) r10:00000000 r9:00000000 r8:00000000 r7:800396f8 r6:9e481380 r5:00000000 r4:9e4f2ec0 [<8003df30>] (kthread) from [<8000eb60>] (ret_from_fork+0x14/0x34) r7:00000000 r6:00000000 r5:8003df30 r4:9e4f2ec0 Code: e3140040 1a00001a e3140020 1a000016 (e596002c) ---[ end trace 193c15c2494ec960 ]--- Fixes: bdb0066d (mfd: syscon: Decouple syscon interface from platform devices) Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
-
Lars-Peter Clausen authored
[ Upstream commit 328f494d ] When inserting a new register into a block at the lower end the present bitmap is currently shifted into the wrong direction. The effect of this is that the bitmap becomes corrupted and registers which are present might be reported as not present and vice versa. Fix this by shifting left rather than right. Fixes: 472fdec7("regmap: rbtree: Reduce number of nodes, take 2") Reported-by:
Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
-
