- 26 Nov, 2016 10 commits
-
-
Sebastian Andrzej Siewior authored
commit 90944e40 upstream. If the gcc is configured to do -fPIE by default then the build aborts later with: | Unsupported relocation type: unknown type rel type name (29) Tagging it stable so it is possible to compile recent stable kernels as well. Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
Michal Marek <mmarek@suse.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Sebastian Andrzej Siewior authored
commit 82031ea2 upstream. Adding -no-PIE to the fstack protector check. -no-PIE was introduced before -fstack-protector so there is no need for a runtime check. Without it the build stops: |Cannot use CONFIG_CC_STACKPROTECTOR_STRONG: -fstack-protector-strong available but compiler is broken due to -mcmodel=kernel + -fPIE if -fPIE is enabled by default. Tagging it stable so it is possible to compile recent stable kernels as well. Signed-off-by:
-
Sebastian Andrzej Siewior authored
commit 8ae94224 upstream. Debian started to build the gcc with -fPIE by default so the kernel build ends before it starts properly with: |kernel/bounds.c:1:0: error: code model kernel does not support PIC mode Also add to KBUILD_AFLAGS due to: |gcc -Wp,-MD,arch/x86/entry/vdso/vdso32/.note.o.d … -mfentry -DCC_USING_FENTRY … vdso/vdso32/note.S |arch/x86/entry/vdso/vdso32/note.S:1:0: sorry, unimplemented: -mfentry isn’t supported for 32-bit in combination with -fpic Tagging it stable so it is possible to compile recent stable kernels as well. Signed-off-by:
-
Linus Walleij authored
commit 93d710a6 upstream. We get the following build error from UM Linux after adding an entry to drivers/iio/gyro/Kconfig that issues "select I2C_MUX": ERROR: "devm_ioremap_resource" [drivers/i2c/muxes/i2c-mux-reg.ko] undefined! ERROR: "of_address_to_resource" [drivers/i2c/muxes/i2c-mux-reg.ko] undefined! It appears that the I2C mux core code depends on HAS_IOMEM for historical reasons, while CONFIG_I2C_MUX_REG does *not* have a direct dependency on HAS_IOMEM. This creates a situation where a allyesconfig or allmodconfig for UM Linux will select I2C_MUX, and will implicitly enable I2C_MUX_REG as well, and the compilation will fail for the register driver. Fix this up by making I2C_MUX_REG depend on HAS_IOMEM and removing the dependency from I2C_MUX. Reported-by:
kbuild test robot <fengguang.wu@intel.com> Reported-by:
Jonathan Cameron <jic23@jic23.retrosnub.co.uk> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Acked-by:
Jonathan Cameron <jic23@kernel.org> Acked-by:
Peter Rosin <peda@axentia.se> Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Oliver Hartkopp authored
commit deb507f9 upstream. Andrey Konovalov reported an issue with proc_register in bcm.c. As suggested by Cong Wang this patch adds a lock_sock() protection and a check for unsuccessful proc_create_data() in bcm_connect(). Reference: http://marc.info/?l=linux-netdev&m=147732648731237Reported-by:
Andrey Konovalov <andreyknvl@google.com> Suggested-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
Oliver Hartkopp <socketcan@hartkopp.net> Acked-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Azhar Shaikh authored
commit 274e43ed upstream. Commit 41a3da2b ("mfd: intel-lpss: Save register context on suspend") saved the register context while going to suspend and also put the device in reset state. Due to the resetting of device, system cannot enter S3/S0ix states when no_console_suspend flag is enabled. The system and serial console both hang. The resetting of device is not needed while going to suspend. Hence remove this code. Fixes: 41a3da2b ("mfd: intel-lpss: Save register context on suspend") Signed-off-by:
Azhar Shaikh <azhar.shaikh@intel.com> Acked-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
-
Miklos Szeredi authored
commit 59c3b76c upstream. If pos is at the beginning of a page and copied is zero then page is not zeroed but is marked uptodate. Fix by skipping everything except unlock/put of page if zero bytes were copied. Reported-by:
Al Viro <viro@zeniv.linux.org.uk> Fixes: 6b12c1b3 ("fuse: Implement write_begin/write_end callbacks") Signed-off-by:
Miklos Szeredi <mszeredi@redhat.com> Signed-off-by:
-
Ignacio Alvarado authored
commit 1650b4eb upstream. Function user_notifier_unregister should be called only once for each registered user notifier. Function kvm_arch_hardware_disable can be executed from an IPI context which could cause a race condition with a VCPU returning to user mode and attempting to unregister the notifier. Signed-off-by:
Ignacio Alvarado <ikalvarado@google.com> Fixes: 18863bdd ("KVM: x86 shared msr infrastructure") Reviewed-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
-
Paolo Bonzini authored
commit 7301d6ab upstream. Reported by syzkaller: [ INFO: suspicious RCU usage. ] 4.9.0-rc4+ #47 Not tainted ------------------------------- ./include/linux/kvm_host.h:536 suspicious rcu_dereference_check() usage! stack backtrace: CPU: 1 PID: 6679 Comm: syz-executor Not tainted 4.9.0-rc4+ #47 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 ffff880039e2f6d0 ffffffff81c2e46b ffff88003e3a5b40 0000000000000000 0000000000000001 ffffffff83215600 ffff880039e2f700 ffffffff81334ea9 ffffc9000730b000 0000000000000004 ffff88003c4f8420 ffff88003d3f8000 Call Trace: [< inline >] __dump_stack lib/dump_stack.c:15 [<ffffffff81c2e46b>] dump_stack+0xb3/0x118 lib/dump_stack.c:51 [<ffffffff81334ea9>] lockdep_rcu_suspicious+0x139/0x180 kernel/locking/lockdep.c:4445 [< inline >] __kvm_memslots include/linux/kvm_host.h:534 [< inline >] kvm_memslots include/linux/kvm_host.h:541 [<ffffffff8105d6ae>] kvm_gfn_to_hva_cache_init+0xa1e/0xce0 virt/kvm/kvm_main.c:1941 [<ffffffff8112685d>] kvm_lapic_set_vapic_addr+0xed/0x140 arch/x86/kvm/lapic.c:2217 Reported-by:
Dmitry Vyukov <dvyukov@google.com> Fixes: fda4e2e8 Cc: Andrew Honig <ahonig@google.com> Signed-off-by:
David Hildenbrand <david@redhat.com> Signed-off-by:
-
Yazen Ghannam authored
commit b0b6e868 upstream. cpu_llc_id (Last Level Cache ID) derivation on AMD Fam17h has an underflow bug when extracting the socket_id value. It starts from 0 so subtracting 1 from it will result in an invalid value. This breaks scheduling topology later on since the cpu_llc_id will be incorrect. For example, the the cpu_llc_id of the *other* CPU in the loops in set_cpu_sibling_map() underflows and we're generating the funniest thread_siblings masks and then when I run 8 threads of nbench, they get spread around the LLC domains in a very strange pattern which doesn't give you the normal scheduling spread one would expect for performance. Other things like EDAC use cpu_llc_id so they will be b0rked too. So, the APIC ID is preset in APICx020 for bits 3 and above: they contain the core complex, node and socket IDs. The LLC is at the core complex level so we can find a unique cpu_llc_id by right shifting the APICID by 3 because then the least significant bit will be the Core Complex ID. Tested-by:
Borislav Petkov <bp@suse.de> Signed-off-by:
Yazen Ghannam <Yazen.Ghannam@amd.com> [ Cleaned up and extended the commit message. ] Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Cc: Aravind Gopalakrishnan <aravindksg.lkml@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Fixes: 3849e91f ("x86/AMD: Fix last level cache topology for AMD Fam17h systems") Link: http://lkml.kernel.org/r/20161108083506.rvqb5h4chrcptj7d@pd.tnicSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
- 21 Nov, 2016 30 commits
-
-
Greg Kroah-Hartman authored
-
David S. Miller authored
[ Upstream commit 0fd0ff01 ] Now that all of the user copy routines are converted to return accurate residual lengths when an exception occurs, we no longer need the broken fixup routines. Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
David S. Miller authored
[ Upstream commit 614da3d9 ] All of __ret{,l}_mone{_asi,_fp,_asi_fpu} are now unused. Signed-off-by:
-
David S. Miller authored
[ Upstream commit ee841d0a ] Report the exact number of bytes which have not been successfully copied when an exception occurs, using the running remaining length. Signed-off-by:
-
David S. Miller authored
[ Upstream commit e93704e4 ] Report the exact number of bytes which have not been successfully copied when an exception occurs, using the running remaining length. Signed-off-by:
-
David S. Miller authored
[ Upstream commit 7ae3aaf5 ] Report the exact number of bytes which have not been successfully copied when an exception occurs, using the running remaining length. Signed-off-by:
-
David S. Miller authored
[ Upstream commit 95707704 ] Report the exact number of bytes which have not been successfully copied when an exception occurs, using the running remaining length. Signed-off-by:
-
David S. Miller authored
[ Upstream commit cb736fdb ] Report the exact number of bytes which have not been successfully copied when an exception occurs, using the running remaining length. Signed-off-by:
-
David S. Miller authored
[ Upstream commit d0796b55 ] Report the exact number of bytes which have not been successfully copied when an exception occurs, using the running remaining length. Signed-off-by:
-
David S. Miller authored
[ Upstream commit 0096ac9f ] Report the exact number of bytes which have not been successfully copied when an exception occurs, using the running remaining length. Signed-off-by:
-
David S. Miller authored
[ Upstream commit 83a17d26 ] The fixup helper function mechanism for handling user copy fault handling is not %100 accurrate, and can never be made so. We are going to transition the code to return the running return return length, which is always kept track in one or more registers of each of these routines. In order to convert them one by one, we have to allow the existing behavior to continue functioning. Therefore make all the copy code that wants the fixup helper to be used return negative one. After all of the user copy routines have been converted, this logic and the fixup helpers themselves can be removed completely. Signed-off-by:
-
David S. Miller authored
[ Upstream commit aa95ce36 ] It is completely unused. Signed-off-by:
-
David S. Miller authored
[ Upstream commit a74ad5e6 ] When the vmalloc area gets fragmented, and because the firmware mapping area sits between where modules live and the vmalloc area, we can sometimes receive requests for enormous kernel TLB range flushes. When this happens the cpu just spins flushing billions of pages and this triggers the NMI watchdog and other problems. We took care of this on the TSB side by doing a linear scan of the table once we pass a certain threshold. Do something similar for the TLB flush, however we are limited by the TLB flush facilities provided by the different chip variants. First of all we use an (mostly arbitrary) cut-off of 256K which is about 32 pages. This can be tuned in the future. The huge range code path for each chip works as follows: 1) On spitfire we flush all non-locked TLB entries using diagnostic acceses. 2) On cheetah we use the "flush all" TLB flush. 3) On sun4v/hypervisor we do a TLB context flush on context 0, which unlike previous chips does not remove "permanent" or locked entries. We could probably do something better on spitfire, such as limiting the flush to kernel TLB entries or even doing range comparisons. However that probably isn't worth it since those chips are old and the TLB only had 64 entries. Reported-by:
James Clarke <jrtc27@jrtc27.com> Tested-by:
-
David S. Miller authored
[ Upstream commit a236441b ] Just like the non-cross-call TLB flush handlers, the cross-call ones need to avoid doing PC-relative branches outside of their code blocks. Signed-off-by:
-
David S. Miller authored
[ Upstream commit 830cda3f ] Noticed by James Clarke. Signed-off-by:
-
David S. Miller authored
[ Upstream commit b429ae4d ] When we copy code over to patch another piece of code, we can only use PC-relative branches that target code within that piece of code. Such PC-relative branches cannot be made to external symbols because the patch moves the location of the code and thus modifies the relative address of external symbols. Use an absolute jmpl to fix this problem. Signed-off-by:
-
David S. Miller authored
[ Upstream commit 849c4987 ] If the number of pages we are flushing is more than twice the number of entries in the TSB, just scan the TSB table for matches rather than probing each and every page in the range. Based upon a patch and report by James Clarke. Signed-off-by:
-
James Clarke authored
[ Upstream commit 9d9fa230 ] Additionally, if the offset will overflow the immediate for a ba,pt instruction, fall back on a standard ba to get an extra 3 bits. Signed-off-by:
-
Mike Kravetz authored
[ Upstream commit af1b1a9b ] do_sparc64_fault() calculates both the base and huge page RSS sizes and uses this information in calls to tsb_grow(). The calculation for base page TSB size is not correct if the task uses hugetlb pages. hugetlb pages are not accounted for in RSS, therefore the call to get_mm_rss(mm) does not include hugetlb pages. However, the number of pages based on huge_pte_count (which does include hugetlb pages) is subtracted from this value. This will result in an artificially small and often negative RSS calculation. The base TSB size is then often set to max_tsb_size as the passed RSS is unsigned, so a negative value looks really big. THP pages are also accounted for in huge_pte_count, and THP pages are accounted for in RSS so the calculation in do_sparc64_fault() is correct if a task only uses THP pages. A single huge_pte_count is not sufficient for TSB sizing if both hugetlb and THP pages can be used. Instead of a single counter, use two: one for hugetlb and one for THP. Signed-off-by:
Mike Kravetz <mike.kravetz@oracle.com> Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit 344e3c77 ] We accidentally take the "port->lock" twice in a row. This old code was supposed to be deleted. Fixes: e58e241c ('sparc: serial: Clean up the locking for -rt') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
David S. Miller authored
[ Upstream commit 4f6deb8c ] On pre-Niagara systems, we fetch the fault address on data TLB exceptions from the TLB_TAG_ACCESS register. But this register also contains the context ID assosciated with the fault in the low 13 bits of the register value. This propagates into current_thread_info()->fault_address and can cause trouble later on. So clear the low 13-bits out of the TLB_TAG_ACCESS value in the cases where it matters. Reported-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
-
Peter Hurley authored
commit dd42bf11 upstream. Line discipline drivers may mistakenly misuse ldisc-related fields when initializing. For example, a failure to initialize tty->receive_room in the N_GIGASET_M101 line discipline was recently found and fixed [1]. Now, the N_X25 line discipline has been discovered accessing the previous line discipline's already-freed private data [2]. Harden the ldisc interface against misuse by initializing revelant tty fields before instancing the new line discipline. [1] commit fd98e941 Author: Tilman Schmidt <tilman@imap.cc> Date: Tue Jul 14 00:37:13 2015 +0200 isdn/gigaset: reset tty->receive_room when attaching ser_gigaset [2] Report from Sasha Levin <sasha.levin@oracle.com> [ 634.336761] ================================================================== [ 634.338226] BUG: KASAN: use-after-free in x25_asy_open_tty+0x13d/0x490 at addr ffff8800a743efd0 [ 634.339558] Read of size 4 by task syzkaller_execu/8981 [ 634.340359] ============================================================================= [ 634.341598] BUG kmalloc-512 (Not tainted): kasan: bad access detected ... [ 634.405018] Call Trace: [ 634.405277] dump_stack (lib/dump_stack.c:52) [ 634.405775] print_trailer (mm/slub.c:655) [ 634.406361] object_err (mm/slub.c:662) [ 634.406824] kasan_report_error (mm/kasan/report.c:138 mm/kasan/report.c:236) [ 634.409581] __asan_report_load4_noabort (mm/kasan/report.c:279) [ 634.411355] x25_asy_open_tty (drivers/net/wan/x25_asy.c:559 (discriminator 1)) [ 634.413997] tty_ldisc_open.isra.2 (drivers/tty/tty_ldisc.c:447) [ 634.414549] tty_set_ldisc (drivers/tty/tty_ldisc.c:567) [ 634.415057] tty_ioctl (drivers/tty/tty_io.c:2646 drivers/tty/tty_io.c:2879) [ 634.423524] do_vfs_ioctl (fs/ioctl.c:43 fs/ioctl.c:607) [ 634.427491] SyS_ioctl (fs/ioctl.c:622 fs/ioctl.c:613) [ 634.427945] entry_SYSCALL_64_fastpath (arch/x86/entry/entry_64.S:188) Cc: Tilman Schmidt <tilman@imap.cc> Cc: Sasha Levin <sasha.levin@oracle.com> Signed-off-by:
Peter Hurley <peter@hurleysoftware.com> Cc: Jiri Slaby <jslaby@suse.cz> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit ac6e7800 ] With syzkaller help, Marco Grassi found a bug in TCP stack, crashing in tcp_collapse() Root cause is that sk_filter() can truncate the incoming skb, but TCP stack was not really expecting this to happen. It probably was expecting a simple DROP or ACCEPT behavior. We first need to make sure no part of TCP header could be removed. Then we need to adjust TCP_SKB_CB(skb)->end_seq Many thanks to syzkaller team and Marco for giving us a reproducer. Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
Marco Grassi <marco.gra@gmail.com> Reported-by:
Vladis Dronov <vdronov@redhat.com> Signed-off-by:
-
Stephen Suryaputra Lin authored
[ Upstream commit 969447f2 ] In v2.6, ip_rt_redirect() calls arp_bind_neighbour() which returns 0 and then the state of the neigh for the new_gw is checked. If the state isn't valid then the redirected route is deleted. This behavior is maintained up to v3.5.7 by check_peer_redirect() because rt->rt_gateway is assigned to peer->redirect_learned.a4 before calling ipv4_neigh_lookup(). After commit 5943634f ("ipv4: Maintain redirect and PMTU info in struct rtable again."), ipv4_neigh_lookup() is performed without the rt_gateway assigned to the new_gw. In the case when rt_gateway (old_gw) isn't zero, the function uses it as the key. The neigh is most likely valid since the old_gw is the one that sends the ICMP redirect message. Then the new_gw is assigned to fib_nh_exception. The problem is: the new_gw ARP may never gets resolved and the traffic is blackholed. So, use the new_gw for neigh lookup. Changes from v1: - use __ipv4_neigh_lookup instead (per Eric Dumazet). Fixes: 5943634f ("ipv4: Maintain redirect and PMTU info in struct rtable again.") Signed-off-by:
Stephen Suryaputra Lin <ssurya@ieee.org> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 34fad54c ] After Tom patch, thoff field could point past the end of the buffer, this could fool some callers. If an skb was provided, skb->len should be the upper limit. If not, hlen is supposed to be the upper limit. Fixes: a6e544b0 ("flow_dissector: Jump to exit code in __skb_flow_dissect") Signed-off-by:
Alexander Duyck <alexander.h.duyck@intel.com> Acked-by:
Willem de Bruijn <willemb@google.com> Acked-by:
Alexei Starovoitov <ast@kernel.org> Signed-off-by:
-
Soheil Hassas Yeganeh authored
[ Upstream commit 3023898b ] Do not send the next message in sendmmsg for partial sendmsg invocations. sendmmsg assumes that it can continue sending the next message when the return value of the individual sendmsg invocations is positive. It results in corrupting the data for TCP, SCTP, and UNIX streams. For example, sendmmsg([["abcd"], ["efgh"]]) can result in a stream of "aefgh" if the first sendmsg invocation sends only the first byte while the second sendmsg goes through. Datagram sockets either send the entire datagram or fail, so this patch affects only sockets of type SOCK_STREAM and SOCK_SEQPACKET. Fixes: 228e548e ("net: Add sendmmsg socket system call") Signed-off-by:
Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by:
Neal Cardwell <ncardwell@google.com> Acked-by:
Maciej Żenczykowski <maze@google.com> Signed-off-by:
-
Alexander Duyck authored
[ Upstream commit fd0285a3 ] The display of /proc/net/route has had a couple issues due to the fact that when I originally rewrote most of fib_trie I made it so that the iterator was tracking the next value to use instead of the current. In addition it had an off by 1 error where I was tracking the first piece of data as position 0, even though in reality that belonged to the SEQ_START_TOKEN. This patch updates the code so the iterator tracks the last reported position and key instead of the next expected position and key. In addition it shifts things so that all of the leaves start at 1 instead of trying to report leaves starting with offset 0 as being valid. With these two issues addressed this should resolve any off by one errors that were present in the display of /proc/net/route. Fixes: 25b97c01 ("ipv4: off-by-one in continuation handling in /proc/net/route") Cc: Andy Whitcroft <apw@canonical.com> Reported-by:
Jason Baron <jbaron@akamai.com> Tested-by:
-
Marcelo Ricardo Leitner authored
[ Upstream commit 7233bc84 ] sctp_wait_for_connect() currently already holds the asoc to keep it alive during the sleep, in case another thread release it. But Andrey Konovalov and Dmitry Vyukov reported an use-after-free in such situation. Problem is that __sctp_connect() doesn't get a ref on the asoc and will do a read on the asoc after calling sctp_wait_for_connect(), but by then another thread may have closed it and the _put on sctp_wait_for_connect will actually release it, causing the use-after-free. Fix is, instead of doing the read after waiting for the connect, do it before so, and avoid this issue as the socket is still locked by then. There should be no issue on returning the asoc id in case of failure as the application shouldn't trust on that number in such situations anyway. This issue doesn't exist in sctp_sendmsg() path. Reported-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Reviewed-by:
Xin Long <lucien.xin@gmail.com> Acked-by:
Neil Horman <nhorman@tuxdriver.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 990ff4d8 ] While fuzzing kernel with syzkaller, Andrey reported a nasty crash in inet6_bind() caused by DCCP lacking a required method. Fixes: ab1e0a13 ("[SOCK] proto: Add hashinfo member to struct proto") Signed-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 1aa9d1a0 ] dccp_v6_err() does not use pskb_may_pull() and might access garbage. We only need 4 bytes at the beginning of the DCCP header, like TCP, so the 8 bytes pulled in icmpv6_notify() are more than enough. Signed-off-by:
-
