While being in an ERROR_WARNING state, and receiving further
bus error events with error counters still in the ERROR_WARNING
range of 97-127 inclusive, the state handling code erroneously
reverts back to ERROR_ACTIVE.

Per the CAN standard, only revert to ERROR_ACTIVE when the
error counters are less than 96.

Moreover, in certain Kvaser models, the BUS_ERROR flag is
always set along with undefined bits in the M16C status
register. Thus use bitwise operators instead of full equality
for checking that register against bus errors.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

On some x86 laptops, plugging a Kvaser device again after an
unplug makes the firmware always ignore the very first command.
For such a case, provide some room for retries instead of
completely exiting the driver init code.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Send expected argument to the URB completion hander: a CAN
netdevice instead of the network interface private context
`kvaser_usb_net_priv'.

This was discovered by having some garbage in the kernel
log in place of the netdevice names: can0 and can1.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Upon receiving a hardware event with the BUS_RESET flag set,
the driver kills all of its anchored URBs and resets all of
its transmit URB contexts.

Unfortunately it does so under the context of URB completion
handler `kvaser_usb_read_bulk_callback()', which is often
called in an atomic context.

While the device is flooded with many received error packets,
usb_kill_urb() typically sleeps/reschedules till the transfer
request of each killed URB in question completes, leading to
the sleep in atomic bug. [3]

In v2 submission of the original driver patch [1], it was
stated that the URBs kill and tx contexts reset was needed
since we don't receive any tx acknowledgments later and thus
such resources will be locked down forever. Fortunately this
is no longer needed since an earlier bugfix in this patch
series is now applied: all tx URB contexts are reset upon CAN
channel close. [2]

Moreover, a BUS_RESET is now treated _exactly_ like a BUS_OFF
event, which is the recommended handling method advised by
the device manufacturer.

[1] http://article.gmane.org/gmane.linux.network/239442
    http://www.webcitation.org/6Vr2yagAQ

[2] can: kvaser_usb: Reset all URB tx contexts upon channel close
    889b77f7

[3] Stacktrace:

 <IRQ>  [<ffffffff8158de87>] dump_stack+0x45/0x57
 [<ffffffff8158b60c>] __schedule_bug+0x41/0x4f
 [<ffffffff815904b1>] __schedule+0x5f1/0x700
 [<ffffffff8159360a>] ? _raw_spin_unlock_irqrestore+0xa/0x10
 [<ffffffff81590684>] schedule+0x24/0x70
 [<ffffffff8147d0a5>] usb_kill_urb+0x65/0xa0
 [<ffffffff81077970>] ? prepare_to_wait_event+0x110/0x110
 [<ffffffff8147d7d8>] usb_kill_anchored_urbs+0x48/0x80
 [<ffffffffa01f4028>] kvaser_usb_unlink_tx_urbs+0x18/0x50 [kvaser_usb]
 [<ffffffffa01f45d0>] kvaser_usb_rx_error+0xc0/0x400 [kvaser_usb]
 [<ffffffff8108b14a>] ? vprintk_default+0x1a/0x20
 [<ffffffffa01f5241>] kvaser_usb_read_bulk_callback+0x4c1/0x5f0 [kvaser_usb]
 [<ffffffff8147a73e>] __usb_hcd_giveback_urb+0x5e/0xc0
 [<ffffffff8147a8a1>] usb_hcd_giveback_urb+0x41/0x110
 [<ffffffffa0008748>] finish_urb+0x98/0x180 [ohci_hcd]
 [<ffffffff810cd1a7>] ? acct_account_cputime+0x17/0x20
 [<ffffffff81069f65>] ? local_clock+0x15/0x30
 [<ffffffffa000a36b>] ohci_work+0x1fb/0x5a0 [ohci_hcd]
 [<ffffffff814fbb31>] ? process_backlog+0xb1/0x130
 [<ffffffffa000cd5b>] ohci_irq+0xeb/0x270 [ohci_hcd]
 [<ffffffff81479fc1>] usb_hcd_irq+0x21/0x30
 [<ffffffff8108bfd3>] handle_irq_event_percpu+0x43/0x120
 [<ffffffff8108c0ed>] handle_irq_event+0x3d/0x60
 [<ffffffff8108ec84>] handle_fasteoi_irq+0x74/0x110
 [<ffffffff81004dfd>] handle_irq+0x1d/0x30
 [<ffffffff81004727>] do_IRQ+0x57/0x100
 [<ffffffff8159482a>] common_interrupt+0x6a/0x6a
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

When hitting an INIT collision case during the 4WHS with AUTH enabled, as
already described in detail in commit 1be9a950 ("net: sctp: inherit
auth_capable on INIT collisions"), it can happen that we occasionally
still remotely trigger the following panic on server side which seems to
have been uncovered after the fix from commit 1be9a950 ...

[  533.876389] BUG: unable to handle kernel paging request at 00000000ffffffff
[  533.913657] IP: [<ffffffff811ac385>] __kmalloc+0x95/0x230
[  533.940559] PGD 5030f2067 PUD 0
[  533.957104] Oops: 0000 [#1] SMP
[  533.974283] Modules linked in: sctp mlx4_en [...]
[  534.939704] Call Trace:
[  534.951833]  [<ffffffff81294e30>] ? crypto_init_shash_ops+0x60/0xf0
[  534.984213]  [<ffffffff81294e30>] crypto_init_shash_ops+0x60/0xf0
[  535.015025]  [<ffffffff8128c8ed>] __crypto_alloc_tfm+0x6d/0x170
[  535.045661]  [<ffffffff8128d12c>] crypto_alloc_base+0x4c/0xb0
[  535.074593]  [<ffffffff8160bd42>] ? _raw_spin_lock_bh+0x12/0x50
[  535.105239]  [<ffffffffa0418c11>] sctp_inet_listen+0x161/0x1e0 [sctp]
[  535.138606]  [<ffffffff814e43bd>] SyS_listen+0x9d/0xb0
[  535.166848]  [<ffffffff816149a9>] system_call_fastpath+0x16/0x1b

... or depending on the the application, for example this one:

[ 1370.026490] BUG: unable to handle kernel paging request at 00000000ffffffff
[ 1370.026506] IP: [<ffffffff811ab455>] kmem_cache_alloc+0x75/0x1d0
[ 1370.054568] PGD 633c94067 PUD 0
[ 1370.070446] Oops: 0000 [#1] SMP
[ 1370.085010] Modules linked in: sctp kvm_amd kvm [...]
[ 1370.963431] Call Trace:
[ 1370.974632]  [<ffffffff8120f7cf>] ? SyS_epoll_ctl+0x53f/0x960
[ 1371.000863]  [<ffffffff8120f7cf>] SyS_epoll_ctl+0x53f/0x960
[ 1371.027154]  [<ffffffff812100d3>] ? anon_inode_getfile+0xd3/0x170
[ 1371.054679]  [<ffffffff811e3d67>] ? __alloc_fd+0xa7/0x130
[ 1371.080183]  [<ffffffff816149a9>] system_call_fastpath+0x16/0x1b

With slab debugging enabled, we can see that the poison has been overwritten:

[  669.826368] BUG kmalloc-128 (Tainted: G        W     ): Poison overwritten
[  669.826385] INFO: 0xffff880228b32e50-0xffff880228b32e50. First byte 0x6a instead of 0x6b
[  669.826414] INFO: Allocated in sctp_auth_create_key+0x23/0x50 [sctp] age=3 cpu=0 pid=18494
[  669.826424]  __slab_alloc+0x4bf/0x566
[  669.826433]  __kmalloc+0x280/0x310
[  669.826453]  sctp_auth_create_key+0x23/0x50 [sctp]
[  669.826471]  sctp_auth_asoc_create_secret+0xcb/0x1e0 [sctp]
[  669.826488]  sctp_auth_asoc_init_active_key+0x68/0xa0 [sctp]
[  669.826505]  sctp_do_sm+0x29d/0x17c0 [sctp] [...]
[  669.826629] INFO: Freed in kzfree+0x31/0x40 age=1 cpu=0 pid=18494
[  669.826635]  __slab_free+0x39/0x2a8
[  669.826643]  kfree+0x1d6/0x230
[  669.826650]  kzfree+0x31/0x40
[  669.826666]  sctp_auth_key_put+0x19/0x20 [sctp]
[  669.826681]  sctp_assoc_update+0x1ee/0x2d0 [sctp]
[  669.826695]  sctp_do_sm+0x674/0x17c0 [sctp]

Since this only triggers in some collision-cases with AUTH, the problem at
heart is that sctp_auth_key_put() on asoc->asoc_shared_key is called twice
when having refcnt 1, once directly in sctp_assoc_update() and yet again
from within sctp_auth_asoc_init_active_key() via sctp_assoc_update() on
the already kzfree'd memory, which is also consistent with the observation
of the poison decrease from 0x6b to 0x6a (note: the overwrite is detected
at a later point in time when poison is checked on new allocation).

Reference counting of auth keys revisited:

Shared keys for AUTH chunks are being stored in endpoints and associations
in endpoint_shared_keys list. On endpoint creation, a null key is being
added; on association creation, all endpoint shared keys are being cached
and thus cloned over to the association. struct sctp_shared_key only holds
a pointer to the actual key bytes, that is, struct sctp_auth_bytes which
keeps track of users internally through refcounting. Naturally, on assoc
or enpoint destruction, sctp_shared_key are being destroyed directly and
the reference on sctp_auth_bytes dropped.

User space can add keys to either list via setsockopt(2) through struct
sctp_authkey and by passing that to sctp_auth_set_key() which replaces or
adds a new auth key. There, sctp_auth_create_key() creates a new sctp_auth_bytes
with refcount 1 and in case of replacement drops the reference on the old
sctp_auth_bytes. A key can be set active from user space through setsockopt()
on the id via sctp_auth_set_active_key(), which iterates through either
endpoint_shared_keys and in case of an assoc, invokes (one of various places)
sctp_auth_asoc_init_active_key().

sctp_auth_asoc_init_active_key() computes the actual secret from local's
and peer's random, hmac and shared key parameters and returns a new key
directly as sctp_auth_bytes, that is asoc->asoc_shared_key, plus drops
the reference if there was a previous one. The secret, which where we
eventually double drop the ref comes from sctp_auth_asoc_set_secret() with
intitial refcount of 1, which also stays unchanged eventually in
sctp_assoc_update(). This key is later being used for crypto layer to
set the key for the hash in crypto_hash_setkey() from sctp_auth_calculate_hmac().

To close the loop: asoc->asoc_shared_key is freshly allocated secret
material and independant of the sctp_shared_key management keeping track
of only shared keys in endpoints and assocs. Hence, also commit 4184b2a7
("net: sctp: fix memory leak in auth key management") is independant of
this bug here since it concerns a different layer (though same structures
being used eventually). asoc->asoc_shared_key is reference dropped correctly
on assoc destruction in sctp_association_free() and when active keys are
being replaced in sctp_auth_asoc_init_active_key(), it always has a refcount
of 1. Hence, it's freed prematurely in sctp_assoc_update(). Simple fix is
to remove that sctp_auth_key_put() from there which fixes these panics.

Fixes: 730fc3d0 ("[SCTP]: Implete SCTP-AUTH parameter processing")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 69ad0dd7
Author: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Date:   Mon May 19 13:59:59 2014 -0300

    net: mv643xx_eth: Use dma_map_single() to map the skb fragments

caused a nasty regression by removing the support for highmem skb
fragments. By using page_address() to get the address of a fragment's
page, we are assuming a lowmem page. However, such assumption is incorrect,
as fragments can be in highmem pages, resulting in very nasty issues.

This commit fixes this by using the skb_frag_dma_map() helper,
which takes care of mapping the skb fragment properly. Additionally,
the type of mapping is now tracked, so it can be unmapped using
dma_unmap_page or dma_unmap_single when appropriate.

This commit also fixes the error path in txq_init() to release the
resources properly.

Fixes: 69ad0dd7 ("net: mv643xx_eth: Use dma_map_single() to map the skb fragments")
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ben Hutchings says:

====================
Fixes for sh_eth #2

I'm continuing review and testing of Ethernet support on the R-Car H2
chip.  This series fixes more of the issues I've found, but it won't be
the last set.

These are not tested on any of the other supported chips.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to stop the RX path accessing the RX ring while it's being
stopped or resized, we clear the interrupt mask (EESIPR) and then call
free_irq() or synchronise_irq().  This is insufficient because the
interrupt handler or NAPI poller may set EESIPR again after we clear
it.  Also, in sh_eth_set_ringparam() we currently don't disable NAPI
polling at all.

I could easily trigger a crash by running the loop:

   while ethtool -G eth0 rx 128 && ethtool -G eth0 rx 64; do echo -n .; done

and 'ping -f' toward the sh_eth port from another machine.

To fix this:
- Add a software flag (irq_enabled) to signal whether interrupts
  should be enabled
- In the interrupt handler, if the flag is clear then clear EESIPR
  and return
- In the NAPI poller, if the flag is clear then don't set EESIPR
- Set the flag before enabling interrupts in sh_eth_dev_init() and
  sh_eth_set_ringparam()
- Clear the flag and serialise with the interrupt and NAPI
  handlers before clearing EESIPR in sh_eth_close() and
  sh_eth_set_ringparam()

After this, I could run the loop for 100,000 iterations successfully.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the device is down then no packet buffers should be allocated.
We also must not touch its registers as it may be powered off.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

We must only ever stop TX queues when they are full or the net device
is not 'ready' so far as the net core, and specifically the watchdog,
is concerned.  Otherwise, the watchdog may fire *immediately* if no
packets have been added to the queue in the last 5 seconds.

What's more, sh_eth_tx_timeout() will likely crash if called while
we're resizing the TX ring.

I could easily trigger this by running the loop:

   while ethtool -G eth0 rx 128 && ethtool -G eth0 rx 64; do echo -n .; done
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

If an skb to be transmitted is shorter than the minimum Ethernet frame
length, we currently set the DMA descriptor length to the minimum but
do not add zero-padding.  This could result in leaking sensitive
data.  We also pass different lengths to dma_map_single() and
dma_unmap_single().

Use skb_padto() to pad properly, before calling dma_map_single().
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

In Dual EMAC, the default VLANs are used to segregate Rx packets between
the ports, so adding the same default VLAN to the switch will affect the
normal packet transfers. So returning error on addition of dual EMAC
default VLANs.

Even if EMAC 0 default port VLAN is added to EMAC 1, it will lead to
break dual EMAC port separations.

Fixes: d9ba8f9e (driver: net: ethernet: cpsw: dual emac interface implementation)
Cc: <stable@vger.kernel.org> # v3.9+
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
Two cls_bpf fixes

Found them while doing a review on act_bpf and going over the
cls_bpf code again. Will also address the first issue in act_bpf
as it needs to be fixed there, too.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When creating a bpf classifier in tc with priority collisions and
invoking automatic unique handle assignment, cls_bpf_grab_new_handle()
will return a wrong handle id which in fact is non-unique. Usually
altering of specific filters is being addressed over major id, but
in case of collisions we result in a filter chain, where handle ids
address individual cls_bpf_progs inside the classifier.

Issue is, in cls_bpf_grab_new_handle() we probe for head->hgen handle
in cls_bpf_get() and in case we found a free handle, we're supposed
to use exactly head->hgen. In case of insufficient numbers of handles,
we bail out later as handle id 0 is not allowed.

Fixes: 7d1d65cb ("net: sched: cls_bpf: add BPF-based classifier")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In cls_bpf_modify_existing(), we read out the number of filter blocks,
do some sanity checks, allocate a block on that size, and copy over the
BPF instruction blob from user space, then pass everything through the
classic BPF checker prior to installation of the classifier.

We should reject mismatches here, there are 2 scenarios: the number of
filter blocks could be smaller than the provided instruction blob, so
we do a partial copy of the BPF program, and thus the instructions will
either be rejected from the verifier or a valid BPF program will be run;
in the other case, we'll end up copying more than we're supposed to,
and most likely the trailing garbage will be rejected by the verifier
as well (i.e. we need to fit instruction pattern, ret {A,K} needs to be
last instruction, load/stores must be correct, etc); in case not, we
would leak memory when dumping back instruction patterns. The code should
have only used nla_len() as Dave noted to avoid this from the beginning.
Anyway, lets fix it by rejecting such load attempts.

Fixes: 7d1d65cb ("net: sched: cls_bpf: add BPF-based classifier")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-3.19-20150121' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2015-01-21

this is a pull request for v3.19, net/master, which consists of a single patch.

Viktor Babrian fixes the issue in the c_can dirver, that the CAN interface
might continue to send frames after the interface has been shut down.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Ursula Braun says:

====================
s390/qeth patches for net

here are two s390/qeth patches built for net.
One patch is quite large, but we would like to fix the locking warning
seen in recent kernels as soon as possible. But if you want me to submit
these patches for net-next, I will do.
Or Gerlitz says:
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Do not wait for channel command buffers in IPA commands.
The potential wait could be done while holding a spin lock and causes
in recent kernels such a bug if kernel lock debugging is enabled:

kernel: BUG: sleeping function called from invalid context at drivers/s390/net/qeth_core_main.c:
794
kernel: in_atomic(): 1, irqs_disabled(): 0, pid: 2031, name: NetworkManager
kernel: 2 locks held by NetworkManager/2031:
kernel:  #0:  (rtnl_mutex){+.+.+.}, at: [<00000000006e0d7a>] rtnetlink_rcv+0x32/0x50
kernel:  #1:  (_xmit_ETHER){+.....}, at: [<00000000006cfe90>] dev_set_rx_mode+0x30/0x50
kernel: CPU: 0 PID: 2031 Comm: NetworkManager Not tainted 3.18.0-rc5-next-20141124 #1
kernel:        00000000275fb1f0 00000000275fb280 0000000000000002 0000000000000000
               00000000275fb320 00000000275fb298 00000000275fb298 00000000007e326a
               0000000000000000 000000000099ce2c 00000000009b4988 000000000000000b
               00000000275fb2e0 00000000275fb280 0000000000000000 0000000000000000
               0000000000000000 00000000001129c8 00000000275fb280 00000000275fb2e0
kernel: Call Trace:
kernel: ([<00000000001128b0>] show_trace+0xf8/0x158)
kernel:  [<000000000011297a>] show_stack+0x6a/0xe8
kernel:  [<00000000007e995a>] dump_stack+0x82/0xb0
kernel:  [<000000000017d668>] ___might_sleep+0x170/0x228
kernel:  [<000003ff80026f0e>] qeth_wait_for_buffer+0x36/0xd0 [qeth]
kernel:  [<000003ff80026fe2>] qeth_get_ipacmd_buffer+0x3a/0xc0 [qeth]
kernel:  [<000003ff80105078>] qeth_l3_send_setdelmc+0x58/0xf8 [qeth_l3]
kernel:  [<000003ff8010b1fe>] qeth_l3_set_ip_addr_list+0x2c6/0x848 [qeth_l3]
kernel:  [<000003ff8010bbb4>] qeth_l3_set_multicast_list+0x434/0xc48 [qeth_l3]
kernel:  [<00000000006cfe9a>] dev_set_rx_mode+0x3a/0x50
kernel:  [<00000000006cff90>] __dev_open+0xe0/0x140
kernel:  [<00000000006d02a0>] __dev_change_flags+0xa0/0x178
kernel:  [<00000000006d03a8>] dev_change_flags+0x30/0x70
kernel:  [<00000000006e14ee>] do_setlink+0x346/0x9a0
...

The device driver has plenty of command buffers available
per channel for channel command communication.
In the extremely rare case when there is no command buffer
available, return a NULL pointer and issue a warning
in the kernel log. The caller handles the case when
a NULL pointer is encountered and returns an error.

In the case the wait for command buffer is possible
(because no lock is held as in the OSN case), still wait
until a channel command buffer is available.
Signed-off-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Reviewed-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the functions that are registering and unregistering MAC
addresses in the qeth-handled hardware, remove callback functions
that are unnesessary, as only the return code is analyzed.
Translate hardware response codes to semi-standard 'errno'-like
codes for readability.

Add kernel-doc description to the internal API function
qeth_send_control_data().
Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Reviewed-by: Thomas-Mich Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In my last commit (a3c00e46: ipv6: Remove BACKTRACK macro), the changes in
__ip6_route_redirect is incorrect.  The following case is missed:
1. The for loop tries to find a valid gateway rt. If it fails to find
   one, rt will be NULL.
2. When rt is NULL, it is set to the ip6_null_entry.
3. The newly added 'else if', from a3c00e46, will stop the backtrack from
   happening.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When registering a mdio bus, Linux assumes than every port has a PHY and tries
to scan it. If a switch port has no PHY registered, DSA will fail to register
the slave MII bus. To fix this, set the slave MII bus PHY mask to the switch
PHYs mask.

As an example, if we use a Marvell MV88E6352 (which is a 7-port switch with no
registered PHYs for port 5 and port 6), with the following declared names:

	static struct dsa_chip_data switch_cdata = {
		[...]
		.port_names[0] = "sw0",
		.port_names[1] = "sw1",
		.port_names[2] = "sw2",
		.port_names[3] = "sw3",
		.port_names[4] = "sw4",
		.port_names[5] = "cpu",
	};

DSA will fail to create the switch instance. With the PHY mask set for the
slave MII bus, only the PHY for ports 0-4 will be scanned and the instance will
be successfully created.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ip6_route_output() always returns a valid dst pointer unlike in IPv4
case. So the validation has to be different from the IPv4 path. Correcting
that error in this patch.

This was picked up by a static checker with a following warning -

   drivers/net/ipvlan/ipvlan_core.c:380 ipvlan_process_v6_outbound()
        warn: 'dst' isn't an ERR_PTR
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The timeout entries are sizeof(int) rather than sizeof(long), which
means that when they were getting read we'd also leak kernel memory
to userspace along with the timeout values.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NAPI poll logic now enforces that a poller returns exactly the budget
when it wants to be called again.

If a driver limits TX completion, it has to return budget as well when
the limit is hit, not the number of received packets.
Reported-and-tested-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: d75b1ade ("net: less interrupt masking in NAPI")
Cc: Manish Chopra <manish.chopra@qlogic.com>
Acked-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With the commit d75b1ade ("net: less interrupt masking in NAPI") napi repoll
is done only when work_done == budget. When we are in busy_poll we return 0 in
napi_poll. We should return budget.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2015-01-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

ath9k:

* fix an IRQ storm caused by commit 872b5d81

iwlwifi:

* A fix for scan that fixes a firmware assertion

* A fix that improves roaming behavior. Same fix has been tested for
  a while in iwldvm. This is a bit of a work around, but the real fix
  should be in mac80211 and will come later.

* A fix for BARs that avoids a WARNING.

* one fix for rfkill while scheduled scan is running.
  Linus's system hit this issue. WiFi would be unavailable
  after this has happpened because of bad state in cfg80211.
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit (3d125f9c) cause i.MX6SX sdb enet cannot work. The cause is
the commit add mdio node with un-correct phy address.

The patch just correct i.MX6sx sdb board enet phy address.

V2:
* As Shawn's suggestion that unit-address should match 'reg' property, so
  update ethernet-phy unit-address.
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Updated hardware documention shows the Rx flow control settings were
moved from the Rx queue operation mode register to a new Rx queue flow
control register.  The old flow control settings are now reserved areas
of the Rx queue operation mode register. Update the code to use the new
register.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Put controller into init mode in network stop to end pending transmissions. The
issue is observed in cases when transmitted frame is not acked.
Signed-off-by: Viktor Babrian <babrian.viktor@renyi.mta.hu>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Pull pin control fixes from Linus Walleij:
 "Here is a (hopefully final) slew of pin control fixes for the v3.19
  series.  The deadlock fix is kind of serious and tagged for stable,
  the rest is business as usual.

   - Fix two deadlocks around the pin control mutexes, a long-standing
     issue that manifest itself in plug/unplug of pin controllers.
     (Tagged for stable.)

   - Handle an error path with zero functions in the Qualcomm pin
     controller.

   - Drop a bogus second GPIO chip added in the Lantiq driver.

   - Fix sudden IRQ loss on Rockchip pin controllers.

   - Register the GIT tree in MAINTAINERS"

* tag 'pinctrl-v3.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: MAINTAINERS: add git tree reference
  pinctrl: qcom: Don't iterate past end of function array
  pinctrl: lantiq: remove bogus of_gpio_chip_add
  pinctrl: Fix two deadlocks
  pinctrl: rockchip: Avoid losing interrupts when supporting both edges

Pull networking fixes from David Miller:

 1) Socket addresses returned in the error queue need to be fully
    initialized before being passed on to userspace, fix from Willem de
    Bruijn.

 2) Interrupt handling fixes to davinci_emac driver from Tony Lindgren.

 3) Fix races between receive packet steering and cpu hotplug, from Eric
    Dumazet.

 4) Allowing netlink sockets to subscribe to unknown multicast groups
    leads to crashes, don't allow it.  From Johannes Berg.

 5) One to many socket races in SCTP fixed by Daniel Borkmann.

 6) Put in a guard against the mis-use of ipv6 atomic fragments, from
    Hagen Paul Pfeifer.

 7) Fix promisc mode and ethtool crashes in sh_eth driver, from Ben
    Hutchings.

 8) NULL deref and double kfree fix in sxgbe driver from Girish K.S and
    Byungho An.

 9) cfg80211 deadlock fix from Arik Nemtsov.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (36 commits)
  s2io: use snprintf() as a safety feature
  r8152: remove sram_read
  r8152: remove generic_ocp_read before writing
  bgmac: activate irqs only if there is nothing to poll
  bgmac: register napi before the device
  sh_eth: Fix ethtool operation crash when net device is down
  sh_eth: Fix promiscuous mode on chips without TSU
  ipv6: stop sending PTB packets for MTU < 1280
  net: sctp: fix race for one-to-many sockets in sendmsg's auto associate
  genetlink: synchronize socket closing and family removal
  genetlink: disallow subscribing to unknown mcast groups
  genetlink: document parallel_ops
  net: rps: fix cpu unplug
  net: davinci_emac: Add support for emac on dm816x
  net: davinci_emac: Fix ioremap for devices with MDIO within the EMAC address space
  net: davinci_emac: Fix incomplete code for getting the phy from device tree
  net: davinci_emac: Free clock after checking the frequency
  net: davinci_emac: Fix runtime pm calls for davinci_emac
  net: davinci_emac: Fix hangs with interrupts
  ip: zero sockaddr returned on error queue
  ...

Pull crypto fix from Herbert Xu:
 "This fixes a regression that arose from the change to add a crypto
  prefix to module names which was done to prevent the loading of
  arbitrary modules through the Crypto API.

  In particular, a number of modules were missing the crypto prefix
  which meant that they could no longer be autoloaded"

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: add missing crypto module aliases

"sp->desc[i]" has 25 characters.  "dev->name" has 15 characters.  If we
used all 15 characters then the sprintf() would overflow.

I changed the "sprintf(sp->name, "%s Neterion %s"" to snprintf(), as
well, even though it can't overflow just to be consistent.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hayes Wang says:

====================
r8152: couldn't read OCP_SRAM_DATA

Read OCP_SRAM_DATA would read additional bytes and may let
the hw abnormal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Read OCP register 0xa43a~0xa43b would clear some flags which the hw
would use, and it may let the device lost. However, the unit of
reading is 4 bytes. That is, it would read 0xa438~0xa43b when calling
sram_read() to read OCP_SRAM_DATA.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For ocp_write_word() and ocp_write_byte(), there is a generic_ocp_read()
which is used to read the whole 4 byte data, keep the unchanged bytes,
and modify the expected bytes. However, the "byen" could be used to
determine which bytes of the 4 bytes to write, so the action could be
removed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hauke Mehrtens says:

====================
bgmac: some fixes to napi usage

I compared the napi documentation with the bgmac driver and found some
problems in that driver. These two patches should fix the problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

IRQs should only get activated when there is nothing to poll in the
queue any more and to after every poll.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

napi should get registered before the netdev and not after.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ben Hutchings says:

====================
sh_eth fixes

I'm currently looking at Ethernet support on the R-Car H2 chip,
reviewing and testing the sh_eth driver.  Here are fixes for two fairly
obvious bugs in the driver; I will probably have some more later.

These are not tested on any of the other supported chips.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>