Marc Kleine-Budde says:

====================
here's a pull request for v3.13, i.e. net/master. It consists of a patch by
Oliver Hartkopp which fixes some corner cases in the interrupt handler of the
sja1000 driver. Then there are two patches for the c_can dirver. One by me,
which fixes a runtime pm related "scheduling while atomic" error and patch by
Holger Bechtold that fixes the calculation of the transmitted bytes.

The fourth patch is by me, it corrects the clock usage in the flexcan
driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We are now using csum_ipv6_magic, include the appropriate header.
Avoids the following error:

    drivers/net/xen-netback/netback.c:1313:4: error: implicit declaration of function 'csum_ipv6_magic' [-Werror=implicit-function-declaration]
        tcph->check = ~csum_ipv6_magic(&ipv6h->saddr,
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In failure case, we should use kfree_skb not
dev_kfree_skb to free skbuff, dev_kfree_skb
is defined as consume_skb.

Trace takes advantage of this point.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit 8ffab51b
(macvlan: lockless tx path), tx stat counter were converted to percpu stat
structure. So we need use to this also for tx_dropped in macvtap. Otherwise, the
management won't notice the dropping packet in macvtap tx path.

Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Vlad Yasevich <vyasevic@redhat.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Phy is compatible with Vitesse 82xx
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently retransmitted DATA chunks could also be used for
RTT measurements since there are no flag to identify whether
the transmitted DATA chunk is a new one or a retransmitted one.
This problem is introduced by commit ae19c548 ("sctp: remove
'resent' bit from the chunk") which inappropriately removed the
'resent' bit completely, instead of doing this, we should set
the resent bit only for the retransmitted DATA chunks.
Signed-off-by: Xufeng Zhang <xufeng.zhang@windriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The pmcraid driver is abusing the genetlink API and is using its
family ID as the multicast group ID, which is invalid and may
belong to somebody else (and likely will.)

Make it use the correct API, but since this may already be used
as-is by userspace, reserve a family ID for this code and also
reserve that group ID to not break userspace assumptions.

My previous patch broke event delivery in the driver as I missed
that it wasn't using the right API and forgot to update it later
in my series.

While changing this, I noticed that the genetlink code could use
the static group ID instead of a strcmp(), so also do that for
the VFS_DQUOT family.

Cc: Anil Ravindranath <anil_ravindranath@pmc-sierra.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/netlink/genetlink.c: In function ‘genl_validate_assign_mc_groups’:
net/netlink/genetlink.c:217: warning: ‘err’ may be used uninitialized in this
function

Commit 2a94fe48 ("genetlink: make multicast
groups const, prevent abuse") split genl_register_mc_group() in multiple
functions, but dropped the initialization of err.

Initialize err to zero to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use new hwmon API to simplify code, provide missing mandatory 'name'
sysfs attribute, and attach hwmon attributes to hwmon device instead
of pci device.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Because the ARP monitoring is not support for 802.3ad, but I still
could change the mode to 802.3ad from ab mode while ARP monitoring
is running, it is incorrect.

So add a check for 802.3ad in bonding_store_mode to fix the problem,
and make a new macro BOND_NO_USES_ARP() to simplify the code.

v2: according to the Dan Williams's suggestion, bond mode is the most
    important bond option, it should override any of the other sub-options.
    So when the mode is changed, the conficting values should be cleared
    or reset, otherwise the user has to duplicate more operations to modify
    the logic. I disable the arp and enable mii monitoring when the bond mode
    is changed to AB, TB and 8023AD if the arp interval is true.

v3: according to the Nik's suggestion, the default value of miimon should need
    a name, there is several place to use it, and the bond_store_arp_interval()
    could use micro BOND_NO_USES_ARP to make the code more simpify.
Suggested-by: Dan Williams <dcbw@redhat.com>
Suggested-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The first netlink attribute (value 0) must always be defined as none/unspec.
This is correctly done in inet_diag.h, but other diag interfaces are wrong.

Because we cannot change an existing API, I add a comment to point the mistake
and avoid to propagate it in a new diag API in the future.

CC: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The flexcan IP core uses the peripheral clock ("per") as basic clock for the
bit timing calculation. However the driver uses the the wrong clock ("ipg").
This leads to wrong bit rates if the rates on both clock are different.

This patch fixes the problem by using the correct clock for the bit rate
calculation.

Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The number of bytes transmitted was not updated correctly, if several CAN
messages (with different length) were transmitted in one 'bunch'. Thus
programs like 'ifconfig' showed wrong transmit byte counts. Reason was, that
the message object whose DLC is to be read was not necessarily the active one
at the time when

    priv->read_reg(priv, C_CAN_IFACE(MSGCTRL_REG, 0)) & IF_MCONT_DLC_MASK;

was executed.
Signed-off-by: Holger Bechtold <Holger.Bechtold@gmx.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The c_can driver contians a callpath (c_can_poll -> c_can_state_change ->
c_can_get_berr_counter) which may call pm_runtime_get_sync() from the IRQ
handler, which is not allowed and results in "BUG: scheduling while atomic".

This problem is fixed by introducing __c_can_get_berr_counter, which will not
call pm_runtime_get_sync().
Reported-by: Andrew Glen <AGlen@bepmarine.com>
Tested-by: Andrew Glen <AGlen@bepmarine.com>
Signed-off-by: Andrew Glen <AGlen@bepmarine.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch fixes the issue that the sja1000_interrupt() function may have
returned IRQ_NONE without processing the optional pre_irq() and post_irq()
function before. Further the irq processing counter 'n' is moved to the end of
the while statement to return correct IRQ_[NONE|HANDLED] values at error
conditions.
Reported-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

On BE3-R, the PF programs the initial MAC address for its VFs. Doing it again
in VF probe, causes a FW error which although harmless generates
an unnecessary error log message.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is not being set currently. (This field is not applicable for Lancer)
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Interrupts need to be enabled in be_resume, when adapter boots back up from D3cold.

disabling interrupts in be_suspend() just to be symmetric to be_resume().
Signed-off-by: Ravikumar Nelavelli <ravikumar.nelavelli@emulex.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If a too small burst is inadvertently set on TBF, we might trigger
a bug in tbf_segment(), as 'skb' instead of 'segs' was used in a
qdisc_reshape_fail() call.

tc qdisc add dev eth0 root handle 1: tbf latency 50ms burst 1KB rate
50mbit

Fix the bug, and add a warning, as such configuration is not
going to work anyway for non GSO packets.

(For some reason, one has to use a burst >= 1520 to get a working
configuration, even with old kernels. This is a probable iproute2/tc
bug)

Based on a report and initial patch from Yang Yingliang

Fixes: e43ac79a ("sch_tbf: segment too big GSO packets")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Offenders don't have port numbers, so set it to 0.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit bceaa902 ("inet: prevent leakage
of uninitialized memory to user in recv syscalls") conditionally updated
addr_len if the msg_name is written to. The recv_error and rxpmtu
functions relied on the recvmsg functions to set up addr_len before.

As this does not happen any more we have to pass addr_len to those
functions as well and set it to the size of the corresponding sockaddr
length.

This broke traceroute and such.

Fixes: bceaa902 ("inet: prevent leakage of uninitialized memory to user in recv syscalls")
Reported-by: Brad Spengler <spender@grsecurity.net>
Reported-by: Tom Labanowski
Cc: mpb <mpb.mail@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Send icmpv6 error with type "destination unreachable" and code
"address unreachable" when receiving icmpv4 error and sufficient
data bytes are available
This patch enhances the compliance of sit tunnel with section 3.4 of
rfc 4213
Signed-off-by: Oussama Ghorbel <ghorbel@pivasoftware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

nobody needs it. remove.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch simplifies the checksum verification in tcpX_gro_receive
by reusing the CHECKSUM_COMPLETE code for CHECKSUM_NONE.  All it
does for CHECKSUM_NONE is compute the partial checksum and then
treat it as if it came from the hardware (CHECKSUM_COMPLETE).
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Cheers,
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In some cases we may receive IP packets that are longer than
their stated lengths.  Such packets are never merged in GRO.
However, we may end up computing their checksums incorrectly
and end up allowing packets with a bogus checksum enter our
stack with the checksum status set as verified.

Since such packets are rare and not performance-critical, this
patch simply skips the checksum verification for them.
Reported-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>

Thanks,
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Function sctp_check_transmitted(transport t, ...) would iterate all of
transport->transmitted queue and looking for the highest __newly__ acked tsn.
The original algorithm would depend on the order of the assoc->transport_list
(in function sctp_outq_sack line 1215 - 1226). The result might not be the
expected due to the order of the tranport_list.

Solution: checking if the exising is smaller than the new one before assigning
Signed-off-by: Chang Xiangzhong <changxiangzhong@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recently GRO started generating packets with frag_lists of frags.
This was not handled by GSO, thus leading to a crash.

Thankfully these packets are of a regular form and are easy to
handle.  This patch handles them in two ways.  For completely
non-linear frag_list entries, we simply continue to iterate over
the frag_list frags once we exhaust the normal frags.  For frag_list
entries with linear parts, we call pskb_trim on the first part
of the frag_list skb, and then process the rest of the frags in
the usual way.

This patch also kills a chunk of dead frag_list code that has
obviously never ever been run since it ends up generating a bogus
GSO-segmented packet with a frag_list entry.

Future work is planned to split super big packets into TSO
ones.

Fixes: 8a29111c ("net: gro: allow to build full sized skb")
Reported-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Reported-by: Jerry Chu <hkchu@google.com>
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Tested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix another really stupid bug - I introduced genl_set_err()
precisely to be able to adjust the group and reject invalid
ones, but then forgot to do so.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Unfortunately, I introduced a tremendously stupid bug into
genlmsg_multicast() when doing all those multicast group
changes: it adjusts the group number, but then passes it
to genlmsg_multicast_netns() which does that again.

Somehow, my tests failed to catch this, so add a warning
into genlmsg_multicast_netns() and remove the offending
group ID adjustment.

Also add a warning to the similar code in other functions
so people who misuse them are more loudly warned.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Salam reported a use after free bug in PF_PACKET that occurs when
we're sending out frames on a socket bound device and suddenly the
net device is being unregistered. It appears that commit 827d9780
introduced a possible race condition between {t,}packet_snd() and
packet_notifier(). In the case of a bound socket, packet_notifier()
can drop the last reference to the net_device and {t,}packet_snd()
might end up suddenly sending a packet over a freed net_device.

To avoid reverting 827d9780 and thus introducing a performance
regression compared to the current state of things, we decided to
hold a cached RCU protected pointer to the net device and maintain
it on write side via bind spin_lock protected register_prot_hook()
and __unregister_prot_hook() calls.

In {t,}packet_snd() path, we access this pointer under rcu_read_lock
through packet_cached_dev_get() that holds reference to the device
to prevent it from being freed through packet_notifier() while
we're in send path. This is okay to do as dev_put()/dev_hold() are
per-cpu counters, so this should not be a performance issue. Also,
the code simplifies a bit as we don't need need_rls_dev anymore.

Fixes: 827d9780 ("af-packet: Use existing netdev reference for bound sockets.")
Reported-by: Salam Noureddine <noureddine@aristanetworks.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Salam Noureddine <noureddine@aristanetworks.com>
Cc: Ben Greear <greearb@candelatech.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the VIF thread is still running after unbinding the Tx and Rx IRQs
in xenvif_disconnect(), the thread may attempt to raise an event which
will BUG (as the irq is unbound).
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This removes a code line that is between a "return 0;" and an error label.
This code line can never be reached.

Found by Coverity (CID: 1130529)
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

John W. Linville says:

====================
pull request: wireless 2013-11-21

Please pull this batch of fixes intended for the 3.13 stream!

For the Bluetooth bits, Gustavo says:

"A few fixes for 3.13. There is 3 fixes to the RFCOMM protocol. One
crash fix to L2CAP. A simple fix to a bad behaviour in the SMP
protocol."

On top of that...

Amitkumar Karwar sends a quintet of mwifiex fixes -- two fixes related
to failure handling, two memory leak fixes, and a NULL pointer fix.

Felix Fietkau corrects and earlier rt2x00 HT descriptor handling fix
to address a crash.

Geyslan G. Bem fixes a memory leak in brcmfmac.

Larry Finger address more pointer arithmetic errors in rtlwifi.

Luis R. Rodriguez provides a regulatory fix in the shared ath code.

Sujith Manoharan brings a couple ath9k initialization fixes.

Ujjal Roy offers one more mwifiex fix to avoid invalid memory accesses
when unloading the USB driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
netfilter fixes for net

The following patchset contains fixes for your net tree, they are:

* Remove extra quote from connlimit configuration in Kconfig, from
  Randy Dunlap.

* Fix missing mss option in syn packets sent to the backend in our
  new synproxy target, from Martin Topholm.

* Use window scale announced by client when sending the forged
  syn to the backend, from Martin Topholm.

* Fix IPv6 address comparison in ebtables, from Luís Fernando
  Cornachioni Estrozi.

* Fix wrong endianess in sequence adjustment which breaks helpers
  in NAT configurations, from Phil Oester.

* Fix the error path handling of nft_compat, from me.

* Make sure the global conntrack counter is decremented after the
  object has been released, also from me.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

Add auto-MDI/MDI-X capability for forced (autonegotiation disabled)
10/100 Mbps speeds on Vitesse VSC82x4 PHYs. Exported previously static
function genphy_setup_forced() required by the new config_aneg handler
in the Vitesse PHY module.
Signed-off-by: Madalin Bucur <madalin.bucur@freescale.com>
Signed-off-by: Shruti Kanetkar <Shruti@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vitesse VSC8662 is Dual Port 10/100/1000Base-T Phy
Its register set and features are similar to other Vitesse Phys.
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Andy Fleming <afleming@gmail.com>
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The VSC8574 is a quad-port Gigabit Ethernet transceiver with four SerDes
interfaces for quad-port dual media capability.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@gmail.com>
Signed-off-by: Shruti Kanetkar <Shruti@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vitesse VSC8234 is quad port 10/100/1000BASE-T PHY
with SGMII and SERDES MAC interfaces.
Signed-off-by: Andy Fleming <afleming@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Shruti Kanetkar <Shruti@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In that case it is probable that kernel code overwrote part of the
stack. So we should bail out loudly here.

The BUG_ON may be removed in future if we are sure all protocols are
conformant.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>