Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

v2: Deal with _CURABASE too
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Handle the HDMI aspect ratio property the same way in the SDVO code
as we handle it in the HDMI code.

v2: Remove stray whitespace change
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Make adjusted_mode const whereever we don't have to modify it. This only
covers cases when we have a local adjusted_mode variable, and doesn't
make any difference for cases where we just dereference
pipe_config->adjusted_mode.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

We shouldn't frob adjusted_mode after .compute_config(), so move the
infoframe aspect ratio setup to .compute_config() from
intel_hdmi_set_avi_infoframe().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

The adjustead_mode crtc_ timings are what we will program into the hardware,
so it's those timings we should be looking practically everywhere.

The normal and crtc_ timings should differ only when stere doubling is
used. In that case the normal timings are the orignal non-doubled
timigns, and crtc_ timings are the doubled timings used by the hardware.

The only case where we continue to look at the normal timings is when we
pass the adjusted_mode to drm_match_{cea,hdmi}_mode() to find the VIC.
drm_edid keeps the modes aronund in the non-double form only, so it
needs the non-double timings to match against.

Done with sed
's/adjusted_mode->\([vhVH]\)/adjusted_mode->crtc_\1/g'
's/adjusted_mode->clock/adjusted_mode->crtc_clock/g'
with a manual s/VDisplay/vdisplay/ within the comment in intel_dvo.c

v2: Update due to intel_dsi.c changes
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Rename the function argument to 'adjusted_mode' whenever the function
only ever gets passed the adjusted_mode.

v2: Update due to intel_dsi.c changes
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Make the giant function a little less giant.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add pipe_ prefix as suggested by Chris.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Make it clear that we're checking whether FBC is supported or not. The
fact that the vfunc is not NULL is just a consequence.

Another name option would have been fbc_initialized().
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

The spec says we just can't use it.

v2:
  - Add WA name (Ville).
  - Add a big comment explaining that we still didn't fix the problem
    where we inherit a framebuffer on the first page (Chris, Ville).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

This fixes the warnings like

"plane A assertion failure, should be disabled but not"

that on the initial modeset during boot. This can happen if
the primary plane is enabled by the firmware, but inheriting
it fails because the DMAR is active or for other reasons.

Most likely caused by

commit 36750f28
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date:   Mon Jun 1 12:49:54 2015 +0200

    drm/i915: update plane state during init

This is the 4.4 version of

commit 721a09f7
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date:   Tue Sep 15 14:28:54 2015 +0200

    drm/i915: Add primary plane to mask if it's visible
Reported-by: Andreas Reis <andreas.reis@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91429Reported-and-tested-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Andreas Reis <andreas.reis@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

v2: Hide the 945 vs. rest of gen2/3 difference in the macro
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Bspec update tells that we have to enable oscaledcompmethod instead of
ouniqetrangenmethod for enabling scale value during swing programming.

v2: Adding back 'don't care' values to bxt_ddi_translations_dp and add
error message if ouniquetrangemethod was set (Imre)
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>(v1)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Adding voltage swing table for edp to support low vswings.

v2: Rebased.
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

According to the PCI docs and Rafael, we don't need to be doing explicit
enables and disables in our init and teardown routines, as they're taken
care of by the PCI core.  So drop the pm_runtime_disable() at teardown
and pm_runtime_set_active() at init.

This fixes one failure of the basic-pci-d3-state test on my BYT.

v2: drop extra get_noresume() and put_noidle() (Rafael)

Signed-off-by: Jesse Barnes <jbarnes at virtuousgeek.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Acked-by: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Bit 16 of GuC status indicates resuming from RC6. The LAPIC_DONE
status is a reliable readiness flag only when resuming from RC6.
This fix a racing issue that allocation of doorbell fails whilst
GuC init is not finished.
Signed-off-by: Alex Dai <yu.dai@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Always name any variable pointing at the adjusted mode as
'adjustead_mode'. This will make it much easier to identify
when we should use the crtc_ timings and when we shoudln't.

Conversion was performed with coccinelle:
@@
expression E;
identifier I;
@@
- struct drm_display_mode *I = &E.adjusted_mode;
+ struct drm_display_mode *adjusted_mode = &E.adjusted_mode;
<...
- I
+ adjusted_mode
...>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
[danvet: Fixup conflicts.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Replace intel_dvo->panel_fixed_mode with the appropriate intel_panel
stuff. Now all connectors that have a fixed mode use intel_panel.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Another interesting criteria to work dmc as expected is pw1 to be
enabled by driver and dmc will shut it off in its execution
sequence. If already disabled by driver dmc will get confuse and
behave differently than expected found during pc10 entry issue
for skl.

So berfore we disable power-well 1, added check if dmc firmware is
present and driver will not disable power well 1, but for any reason
if firmware is not present of failed to load we can shut off the
power well 1 which will save some power.

As skl is currently fully dependent on dmc to go in lowest possible
power state (dc6) but the same is not applicable for bxt. Display
engine can enter into dc9 without dmc, hence unblocking disable call.

v1: Initial version.

v2: Rebased as per current patch series.

Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Reviewed-by: A.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

While display engine entering into low power state no need to disable
cdclk pll as CSR firmware of dmc will take care. If pll is already
enabled firmware execution sequence will be blocked. This is one
of the criteria for dmc to work properly.

v1: Initial version.

v2: Based on review comment from Daniel added code commnent.

Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-bt: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Reviewed-by: A.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

This patch remove the function call to set the firmware
loading status as uninitialized during suspend.

Dmc firmware will restore the firmware in normal suspend. In previous
patch added a check to directly read the hardware status and load
the firmware if got reset during resume from suspend-hibernation.

Cc: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Reviewed-by: A.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Dmc will restore the csr program except DC9, cold boot,
warm reset, PCI function level reset, and hibernate/suspend.

intel_csr_load_program() function is used to load the firmware
data from kernel memory to csr address space.

All values of csr address space will be zero if it got reset and
the first byte of csr program is always a non-zero if firmware
is loaded successfuly. Based on hardware status will load the
firmware.

Without this condition check if we overwrite the firmware data the
counters exposed for dc5/dc6 (help for debugging) will be nullified.

Note: Above commit message seems to be confused and the real problem
apparently going on is that for suspend-to-idle and system standby the
firmware survives (it's like runtime pm), but it doesn't for
suspend-to-mem and hibernate-to-disk. All the other talking about DC9
and pci reset are irrelevant for the path touched here (only driver
load and system resume functions) and might not be true statements.

v1: Initial version.

v2: Based on review comments from Daniel,
- Added a check to know hardware status and load the firmware if not loaded.

Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Reviewed-by: A.Sunil Kamath <sunil.kamath@intel.com>
[danvet: Explain clearly in the code comment when we need to reload
and when not and make it a FIXME. Also deconfuse the commit message
with a note. Also: Make. it. compile.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Virtualized systems often use a virtual P2X4 south bridge.
Detect this in intel_detect_pch and make a best guess as to which PCH
we should be using.

This was seen on vmware esxi hypervisor. When passing the graphics device
through to a guest, it can not pass through the PCH. Instead it simulates
a P2X4 southbridge.
Signed-off-by: Robert Beckett <robert.beckett@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Backmerge to catch up with 4.3. slightly more involved conflict in the
irq code, but nothing beyond adjacent changes.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>

Another attempt at drm-misc for 4.4 ...
- better atomic helpers for runtime pm drivers
- atomic fbdev
- dp aux i2c STATUS_UPDATE handling (for short i2c replies from the sink)
- bunch of constify patches
- inital kerneldoc for vga switcheroo
- some vblank code cleanups from Ville and Thierry
- various polish all over

* tag 'topic/drm-misc-2015-09-25' of git://anongit.freedesktop.org/drm-intel: (57 commits)
  drm/irq: Add drm_crtc_vblank_count_and_time()
  drm/irq: Rename drm_crtc -> crtc
  drm: drm_atomic_crtc_get_property should be static
  drm/gma500: Remove DP_LINK_STATUS_SIZE redefinition
  vga_switcheroo: Set active attribute to false for audio clients
  drm/core: Preserve the fb id on close.
  drm/core: Preserve the framebuffer after removing it.
  drm: Use vblank timestamps to guesstimate how many vblanks were missed
  drm: store_vblank() is never called with NULL timestamp
  drm: Clean up drm_calc_vbltimestamp_from_scanoutpos() vbl_status
  drm: Limit the number of .get_vblank_counter() retries
  drm: Pass flags to drm_update_vblank_count()
  drm/i915: Fix vblank count variable types
  drm: Kill pixeldur_ns
  drm: Stop using linedur_ns and pixeldur_ns for vblank timestamps
  drm: Move timestamping constants into drm_vblank_crtc
  drm/fbdev: Update legacy plane->fb refcounting for atomic restore
  drm: fix kernel-doc warnings in drm_crtc.h
  vga_switcheroo: Sort headers alphabetically
  drm: Spell vga_switcheroo consistently
  ...

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Pull x86 fixes from Thomas Gleixner:
 "Two bugfixes from Andy addressing at least some of the subtle NMI
  related wreckage which has been reported by Sasha Levin"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/nmi/64: Fix a paravirt stack-clobbering bug in the NMI code
  x86/paravirt: Replace the paravirt nop with a bona fide empty function

Pull irq fix from Thomass Gleixner:
 "A bugfix for the atmel aic5 irq chip driver which caches the wrong
  data and thereby breaking resume"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/atmel-aic5: Use per chip mask caches in mask/unmask()

Pull ARM fixes from Russell King:
 "Just two fixes: wire up the new system calls added during the last
  merge window, and fix another user access site"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: alignment: fix alignment handling for uaccess changes
  ARM: wire up new syscalls

Pull ARM SoC fixes from Olof Johansson:
 "Our first real batch of fixes this release cycle.  Nothing really
  concerning, and diffstat is a bit inflated due to some DT contents
  moving around on STi platforms.

  There's a collection of them here:

   - A fixup for a build breakage that hits on arm64 allmodconfig in
     QCOM SCM firmware drivers
   - MMC fixes for OMAP that had quite a bit of breakage this merge
     window.
   - Misc build/warning fixes on PXA and OMAP
   - A couple of minor fixes for Beagleboard X15 which is now starting
     to see a few more users in the wild"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
  ARM: sti: dt: adapt DT to fix probe/bind issues in DRM driver
  ARM: dts: fix omap2+ address translation for pbias
  firmware: qcom: scm: Add function stubs for ARM64
  ARM: dts: am57xx-beagle-x15: use palmas-usb for USB2
  ARM: omap2plus_defconfig: enable GPIO_PCA953X
  ARM: dts: omap5-uevm.dts: fix i2c5 pinctrl offsets
  ARM: OMAP2+: AM43XX: Enable autoidle for clks in am43xx_init_late
  ARM: dts: am57xx-beagle-x15: Update Phy supplies
  ARM: pxa: balloon3: Fix build error
  ARM: dts: Fixup model name for HP t410 dts
  ARM: dts: DRA7: fix a typo in ethernet
  ARM: omap2plus_defconfig: make PCF857x built-in
  ARM: dts: Use ti,pbias compatible string for pbias
  ARM: OMAP5: Cleanup options for SoC only build
  ARM: DRA7: Select missing options for SoC only build
  ARM: OMAP2+: board-generic: Remove stale of_irq macros
  ARM: OMAP4+: PM: erratum is used by OMAP5 and DRA7 as well
  ARM: dts: omap3-igep: Move eth IRQ pinmux to IGEPv2 common dtsi
  ARM: dts: am57xx-beagle-x15: Add wakeup irq for mcp79410
  ARM: dts: am335x-phycore-som: Fix mpu voltage
  ...

Pull CIFS fixes from Steve French:
 "Four fixes from testing at the recent SMB3 Plugfest including two
  important authentication ones (one fixes authentication problems to
  some popular servers when clock times differ more than two hours
  between systems, the other fixes Kerberos authentication for SMB3)"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  fix encryption error checks on mount
  [SMB3] Fix sec=krb5 on smb3 mounts
  cifs: use server timestamp for ntlmv2 authentication
  disabling oplocks/leases via module parm enable_oplocks broken for SMB3

ARM: pxa: fixes for v4.3

These fixes are mainly regression fixes triggered by irq changes,
common clock framework introduction and sound side-effect of
other platforms.

* tag 'pxa-fixes-v4.3' of https://github.com/rjarzmik/linux:
  ARM: pxa: balloon3: Fix build error
  ARM: pxa: ssp: Fix build error by removing originally incorrect DT binding
  ARM: pxa: fix DFI bus lockups on startup
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v4.3/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Fixes for omaps for v4.3-rc cycle:

- Two more patches to fix most of the MMC regressions with the
  PBIAS regulator changes. At least two MMC driver related issues
  still seems to remain for omap3 legacy booting and omap4 duovero.
  Note that the dts changes depend on a recent regulator fix, and
  are based on the regulator commit now in mainline kernel

- Enable autoidle for am43xx clocks to prevent clocks from staying
  always on

- Fix i2c5 pinctrl offsets for omap5-uevm

- Enable PCA953X as that's needed for HDMI to work on omap5

- Update phy supplies for beagle x15 beta board

- Use palmas-usb for on beagle x15 to start using the related
  driver that recently got merged

* tag 'omap-for-v4.3/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: fix omap2+ address translation for pbias
  ARM: dts: am57xx-beagle-x15: use palmas-usb for USB2
  ARM: omap2plus_defconfig: enable GPIO_PCA953X
  ARM: dts: omap5-uevm.dts: fix i2c5 pinctrl offsets
  ARM: OMAP2+: AM43XX: Enable autoidle for clks in am43xx_init_late
  ARM: dts: am57xx-beagle-x15: Update Phy supplies
  regulator: pbias: program pbias register offset in pbias driver
  ARM: omap2plus_defconfig: Enable MUSB DMA support
  ARM: DRA752: Add ID detect for ES2.0
  ARM: OMAP3: vc: fix 'or' always true warning
  ARM: OMAP2+: Fix booting if no timer parent clock is available
  ARM: OMAP2+: omap-device: fix race deferred probe of omap_hsmmc vs omap_device_late_init
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull crypto fixes from Herbert Xu:
 "This fixes the following issues:

   - check the return value of platform_get_irq as signed int in xgene.

   - skip adf_dev_restore on virtual functions in qat.

   - fix double-free with backlogged requests in marvell_cesa"

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  hwrng: xgene - fix handling platform_get_irq
  crypto: qat - VF should never trigger SBR on PH
  crypto: marvell - properly handle CRYPTO_TFM_REQ_MAY_BACKLOG-flagged requests