- 11 Apr, 2011 11 commits
-
-
Michał Mirosław authored
This also fixes possible race when changing receive checksum state and removes IPV6_CSUM_GEN_HACK as it's always set. BTW, The claim about fake IPV6 checksum looks dubious. If that were true, then there's a problem in networking core and should be fixed there and not in random drivers. BTW#2, there's no MAINTAINERS entry for this driver. I assume this driver is supported by Micrel? Signed-off-by:
Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Michał Mirosław authored
This also removes TSO as it's made fully in software --- better to leave this to networking core. If the MAC features can be detected at probe time and not at open, then stmmac_fix_features could be simplified by limiting hw_features. That's also better for users as they don't see offloads being togglable but never turned on. Redundant fallbacks for TX csum are removed as it's already handled by network core. Signed-off-by:
-
Michał Mirosław authored
Signed-off-by:
-
Michał Mirosław authored
Simple conversion with a bit of needed cleanup. This also fixes: - confusion around vlan_features in rtl8169_vlan_mode(), - problem with broken TSO for too big MTU (the limit is set at 0xFFF --- max MSS field value). SG+IP_CSUM+TSO is left disabled by default, based on suggestion by David Dillow. Signed-off-by:
-
Michał Mirosław authored
Fix up after merge with NETIF_F_RXHASH implementation. This allows to toggle NETIF_F_RXHASH and NETIF_F_HW_VLAN_TX. Signed-off-by:
-
Michał Mirosław authored
Remove offload changing ethtool ops which drivers don't really support: - fs_enet - ucc_geth Signed-off-by:
-
Michael Smith authored
The reverse path filter interferes with IPsec subnet-to-subnet tunnels, especially when the link to the IPsec peer is on an interface other than the one hosting the default route. With dynamic routing, where the peer might be reachable through eth0 today and eth1 tomorrow, it's difficult to keep rp_filter enabled unless fake routes to the remote subnets are configured on the interface currently used to reach the peer. IPsec provides a much stronger anti-spoofing policy than rp_filter, so this patch disables the rp_filter for packets with a security path. Signed-off-by:
Michael Smith <msmith@cbnco.com> Signed-off-by:
-
Michael Smith authored
This makes sk_buff available for other use in fib_validate_source(). Signed-off-by:
-
simon authored
This patch adds some debug to the reset function to print out the reason why it fails. Signed-off-by:
Simon Wood <simon@mungewell.org> Signed-off-by:
-
simon authored
This patch adds support for the PL-25A1 by adding the appropriate USB ID's. This chip is used in the Belkin 'Windows Easy Transfer' Cables. Signed-off-by:
-
simon authored
This patch cleans up a couple of instances of incorrect whitespace Signed-off-by:
-
- 08 Apr, 2011 8 commits
-
-
Dimitris Michailidis authored
Signed-off-by:
Dimitris Michailidis <dm@chelsio.com> Signed-off-by:
-
Dimitris Michailidis authored
Signed-off-by:
-
Michael Chan authored
When cnic_stop_hw() -> cnic_cm_stop_bnx2x_hw() is called under rtnl_lock() from NETDEV_DOWN event, it waits for cnic_delete_task() to complete. It will deadlock when cnic_delete_task() takes rtnl_lock() before calling cnic_ulp_stop_one(). We fix it by removing the rtnl_lock() in cnic_delete_task(). cnic_ulp_stop_one() has mutex and atomic bit ops to prevent important operations from being done more than once, so it is not necessary to take rtnl_lock(). Signed-off-by:
Michael Chan <mchan@broadcom.com> Signed-off-by:
-
Michał Mirosław authored
Things left as they were: - atl1: is RX checksum really enabled? - atl2: copy-paste from atl1, with-errors-on-modify I presume - atl1c: there's a bug: MTU can't be changed if device is not up Signed-off-by:
-
Michał Mirosław authored
Cleanup hint: Some features are calculated in tg3_get_invariants() and the rest in its caller --- tg3_init_one(). This is not changed here. Signed-off-by:
Matt Carlson <mcarlson@broadcom.com> Signed-off-by:
-
Michał Mirosław authored
As the driver uses GRO and not LRO, LRO settings are ignored anyway and are removed here to avoid confusion. Signed-off-by:
-
Michał Mirosław authored
Simple conversion. This also fixes a bug in TX checksum toggling --- driver was changing NETIF_F_HW_CSUM instead of NETIF_F_IP_CSUM+NETIF_F_IPV6_CSUM. Signed-off-by:
-
Michał Mirosław authored
just IP_CSUM. This needs testing and so is not changed here. Signed-off-by:
-
- 07 Apr, 2011 8 commits
-
-
Ajit Khaparde authored
Calling setup_wol after a reset is inconsequential. The WOL setting should be programmed before FLR. And yes, FLR does not erase wol information. Signed-off-by:
Ajit Khaparde <ajit.khaparde@emulex.com> Signed-off-by:
-
Ajit Khaparde authored
Instead of a fixed sized array for vf_cfg, allocate the size dynamically depending on number of VFs the device supports. Signed-off-by:
-
Ajit Khaparde authored
The user supplied num_vfs value need not be compared against a static BE_MAX_VF, but can be checked against the actual VFs that the device can support. Signed-off-by:
-
Ajit Khaparde authored
Lancer and BE can both use SLI_INTF_REG to check a VF or a PF. Signed-off-by:
-
Ajit Khaparde authored
Add rxhash support, Based on initial work by Eric Dumazet. Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
-
David S. Miller authored
Conflicts: drivers/net/benet/be_main.c
-
OGAWA Hirofumi authored
Commit 1018b5c0 ("Set rt->rt_iif more sanely on output routes.") breaks rt_is_{output,input}_route. This became the cause to return "IP_PKTINFO's ->ipi_ifindex == 0". To fix it, this does: 1) Add "int rt_route_iif;" to struct rtable 2) For input routes, always set rt_route_iif to same value as rt_iif 3) For output routes, always set rt_route_iif to zero. Set rt_iif as it is done currently. 4) Change rt_is_{output,input}_route() to test rt_route_iif Signed-off-by:
OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Signed-off-by:
-
Wei Yongjun authored
commit c6e1a0d1 broken the calc (net: Allow no-cache copy from user on transmit) of checksum, which may cause some tcp packets be dropped because incorrect checksum. ssh does not work under today's net-next-2.6 tree. Signed-off-by:
Wei Yongjun <yjwei@cn.fujitsu.com> Acked-by:
Tom Herbert <therbert@google.com> Signed-off-by:
-
- 06 Apr, 2011 13 commits
-
-
stephen hemminger authored
Use ethtool infrastructure for blinking, which is now does locking at higher level. Signed-off-by:
Stephen Hemminger <shemminger@vyatta.com> Signed-off-by:
-
stephen hemminger authored
Convert driver to use new ethtool set_phys_id. Not completely sure that this is correct for all cases of device up/down and doing operation. Compile tested only. Signed-off-by:
-
Michał Mirosław authored
Rather simple conversion to hw_features. Signed-off-by:
-
Jan Kiszka authored
udev fully replaces this special file system that only contains CAPI NCCI TTY device nodes. User space (pppdcapiplugin) works without noticing the difference. Signed-off-by:
Jan Kiszka <jan.kiszka@web.de> Signed-off-by:
-
Ian Campbell authored
Fixes error from sparse: CHECK drivers/net/xen-netback/xenbus.c drivers/net/xen-netback/xenbus.c:29:40: error: dubious one-bit signed bitfield int have_hotplug_status_watch:1; Reported-by:Dr. David Alan Gilbert <linux@treblig.org> Signed-off-by:
Ian Campbell <ian.campbell@citrix.com> Signed-off-by:
-
Ian Campbell authored
Signed-off-by:
-
Padmanabh Ratnakar authored
eq_next_idx is not getting reset to zero during suspend. This causes resume to fail. Added the fix. Signed-off-by:
Sarveswara Rao Mygapula <sarveswararao.mygapula@emulex.com> Signed-off-by:
Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com> Signed-off-by:
-
Padmanabh Ratnakar authored
Renamed msix_vec_idx to eq_idx in be_eq_obj struct. Renamed msix_vec_next_idx to eq_next_idx in be_adapter structure. These members are used in INTX mode also. Signed-off-by:
-
stephen hemminger authored
Convert to new ethtool set physical id model. Remove no longer used timer, and fix docbook comment. Signed-off-by:
-
stephen hemminger authored
Signed-off-by:
-
stephen hemminger authored
Signed-off-by:
-
stephen hemminger authored
Signed-off-by:
-
stephen hemminger authored
Also cleanup error codes to no lie about things that driver doesn't support. If device is down report -EAGAIN (same as Broadcom), and if port doesn't blink then error as well. Signed-off-by:
-
