- 13 Mar, 2019 40 commits
-
-
Jan Kiszka authored
commit 83b94417 upstream. Somewhere along recent changes to power control of the wl1835, power-on became very unreliable on the hikey, failing like this: wl1271_sdio: probe of mmc2:0001:1 failed with error -16 wl1271_sdio: probe of mmc2:0001:2 failed with error -16 After playing with some dt parameters and comparing to other users of this chip, it turned out we need some power-on delay to make things stable again. In contrast to those other users which define 200 ms, the hikey would already be happy with 1 ms. Still, we use the safer 10 ms, like on the Ultra96. Fixes: ea452678 ("arm64: dts: hikey: Fix WiFi support") Cc: <stable@vger.kernel.org> #4.12+ Signed-off-by:
Jan Kiszka <jan.kiszka@siemens.com> Acked-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Wei Xu <xuwei5@hisilicon.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jan Kiszka authored
commit 35a4f89c upstream. Somewhere along recent changes to power control of the wl1831, power-on became very unreliable on the Ultra96, failing like this: wl1271_sdio: probe of mmc2:0001:1 failed with error -16 wl1271_sdio: probe of mmc2:0001:2 failed with error -16 After playing with some dt parameters and comparing to other users of this chip, it turned out we need some power-on delay to make things stable again. In contrast to those other users which define 200 ms, Ultra96 is already happy with 10 ms. Fixes: 5869ba06 ("arm64: zynqmp: Add support for Xilinx zcu100-revC") Signed-off-by:
Michal Simek <michal.simek@xilinx.com> Signed-off-by:
-
Alexander Shishkin authored
commit 2e095ce7 upstream. On Denverton's integration of the Intel(R) Trace Hub (for a reference and overview see Documentation/trace/intel_th.rst) the reported size of one of its resources (RTIT_BAR) doesn't match its actual size, which leads to overlaps with other devices' resources. In practice, it overlaps with XHCI MMIO space, which results in the xhci driver bailing out after seeing its registers as 0xffffffff, and perceived disappearance of all USB devices: intel_th_pci 0000:00:1f.7: enabling device (0004 -> 0006) xhci_hcd 0000:00:15.0: xHCI host controller not responding, assume dead xhci_hcd 0000:00:15.0: xHC not responding in xhci_irq, assume controller is dead xhci_hcd 0000:00:15.0: HC died; cleaning up usb 1-1: USB disconnect, device number 2 For this reason, we need to resize the RTIT_BAR on Denverton to its actual size, which in this case is 4MB. The corresponding erratum is DNV36 at the link below: DNV36. Processor Host Root Complex May Incorrectly Route Memory Accesses to Intel
® Trace Hub Problem: The Intel® Trace Hub RTIT_BAR (B0:D31:F7 offset 20h) is reported as a 2KB memory range. Due to this erratum, the processor Host Root Complex will forward addresses from RTIT_BAR to RTIT_BAR + 4MB -1 to Intel® Trace Hub. Implication: Devices assigned within the RTIT_BAR to RTIT_BAR + 4MB -1 space may not function correctly. Workaround: A BIOS code change has been identified and may be implemented as a workaround for this erratum. Status: No Fix. Note that 5118ccd3 ("intel_th: pci: Add Denverton SOC support") updates the Trace Hub driver so it claims the Denverton device, but the resource overlap exists regardless of whether that driver is loaded or that commit is included. Link: https://www.intel.com/content/dam/www/public/us/en/documents/specification-updates/atom-c3000-family-spec-update.pdfSigned-off-by:Alexander Shishkin <alexander.shishkin@linux.intel.com> [bhelgaas: include erratum text, clarify relationship with 5118ccd3] Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Gustavo A. R. Silva authored
commit 5e420fe6 upstream. Add missing break statement and fix identation issue. This bug was found thanks to the ongoing efforts to enable -Wimplicit-fallthrough. Fixes: 9cb62fa2 ("aacraid: Log firmware AIF messages") Cc: stable@vger.kernel.org Signed-off-by:
Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Gustavo A. R. Silva authored
commit df997abe upstream. Add missing break statement in order to prevent the code from falling through to case ISCSI_BOOT_TGT_NAME, which is unnecessary. This bug was found thanks to the ongoing efforts to enable -Wimplicit-fallthrough. Fixes: b33a84a3 ("ibft: convert iscsi_ibft module to iscsi boot lib") Cc: stable@vger.kernel.org Signed-off-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by:
-
Vincent Batts authored
commit e154ab69 upstream. Lenovo s21e-20 uses ELAN0601 in its ACPI tables for the Elan touchpad. Signed-off-by:
Vincent Batts <vbatts@hashbangbash.com> Cc: stable@vger.kernel.org Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Jason Gerecke authored
commit 44fc95e2 upstream. Tablet initially begins communicating at 9600 baud, so this command should be used to connect to the device: $ inputattach --daemon --baud 9600 --wacom_iv /dev/ttyS0 https://github.com/linuxwacom/xf86-input-wacom/issues/40Signed-off-by:
Jason Gerecke <jason.gerecke@wacom.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Keith Busch authored
[ Upstream commit 4726bcf3 ] The reset work holds a mutex to prevent races with removal modifying the same resources, but was unlocking only on success. Unlock on failure too. Fixes: 5c959d73 ("nvme-pci: fix rapid add remove sequence") Signed-off-by:
Keith Busch <keith.busch@intel.com> Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Liu Bo authored
[ Upstream commit 8c772a9b ] Our test reported the following stack, and vmcore showed that ->inflight counter is -1. [ffffc9003fcc38d0] __schedule at ffffffff8173d95d [ffffc9003fcc3958] schedule at ffffffff8173de26 [ffffc9003fcc3970] io_schedule at ffffffff810bb6b6 [ffffc9003fcc3988] blkcg_iolatency_throttle at ffffffff813911cb [ffffc9003fcc3a20] rq_qos_throttle at ffffffff813847f3 [ffffc9003fcc3a48] blk_mq_make_request at ffffffff8137468a [ffffc9003fcc3b08] generic_make_request at ffffffff81368b49 [ffffc9003fcc3b68] submit_bio at ffffffff81368d7d [ffffc9003fcc3bb8] ext4_io_submit at ffffffffa031be00 [ext4] [ffffc9003fcc3c00] ext4_writepages at ffffffffa03163de [ext4] [ffffc9003fcc3d68] do_writepages at ffffffff811c49ae [ffffc9003fcc3d78] __filemap_fdatawrite_range at ffffffff811b6188 [ffffc9003fcc3e30] filemap_write_and_wait_range at ffffffff811b6301 [ffffc9003fcc3e60] ext4_sync_file at ffffffffa030cee8 [ext4] [ffffc9003fcc3ea8] vfs_fsync_range at ffffffff8128594b [ffffc9003fcc3ee8] do_fsync at ffffffff81285abd [ffffc9003fcc3f18] sys_fsync at ffffffff81285d50 [ffffc9003fcc3f28] do_syscall_64 at ffffffff81003c04 [ffffc9003fcc3f50] entry_SYSCALL_64_after_swapgs at ffffffff81742b8e The ->inflight counter may be negative (-1) if 1) blk-iolatency was disabled when the IO was issued, 2) blk-iolatency was enabled before this IO reached its endio, 3) the ->inflight counter is decreased from 0 to -1 in endio() In fact the hang can be easily reproduced by the below script, H=/sys/fs/cgroup/unified/ P=/sys/fs/cgroup/unified/test echo "+io" > $H/cgroup.subtree_control mkdir -p $P echo $$ > $P/cgroup.procs xfs_io -f -d -c "pwrite 0 4k" /dev/sdg echo "`cat /sys/block/sdg/dev` target=1000000" > $P/io.latency xfs_io -f -d -c "pwrite 0 4k" /dev/sdg This fixes the problem by freezing the queue so that while enabling/disabling iolatency, there is no inflight rq running. Note that quiesce_queue is not needed as this only updating iolatency configuration about which dispatching request_queue doesn't care. Signed-off-by:
Liu Bo <bo.liu@linux.alibaba.com> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Sudarsana Reddy Kalluru authored
[ Upstream commit 0aa4febb ] Under heavy traffic load, when changing number of channels via ethtool (ethtool -L) which will cause interface to be reloaded, it was observed that some packets gets transmitted on old TX channel/queue id which doesn't really exist after the channel configuration leads to system crash. Add a safeguard in the driver by validating queue id through ndo_select_queue() which is called before the ndo_start_xmit(). Signed-off-by:
Sudarsana Reddy Kalluru <skalluru@marvell.com> Signed-off-by:
Ariel Elior <aelior@marvell.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Sudarsana Reddy Kalluru authored
[ Upstream commit fb1faab7 ] Max supported queues is derived incorrectly in the case of multi-CoS. Need to consider TCs while calculating num_queues for PF. Signed-off-by:
-
Manish Chopra authored
[ Upstream commit 660492bc ] When slowpath messages are sent with high rate, the resulting events can lead to a FW assert in case they are not handled fast enough (Event Queue Full assert). Attempt to send queued slowpath messages only after the newly evacuated entries in the EQ ring are indicated to FW. Signed-off-by:
Manish Chopra <manishc@marvell.com> Signed-off-by:
-
Tetsuo Handa authored
[ Upstream commit 43636c80 ] When something let __find_get_block_slow() hit all_mapped path, it calls printk() for 100+ times per a second. But there is no need to print same message with such high frequency; it is just asking for stall warning, or at least bloating log files. [ 399.866302][T15342] __find_get_block_slow() failed. block=1, b_blocknr=8 [ 399.873324][T15342] b_state=0x00000029, b_size=512 [ 399.878403][T15342] device loop0 blocksize: 4096 [ 399.883296][T15342] __find_get_block_slow() failed. block=1, b_blocknr=8 [ 399.890400][T15342] b_state=0x00000029, b_size=512 [ 399.895595][T15342] device loop0 blocksize: 4096 [ 399.900556][T15342] __find_get_block_slow() failed. block=1, b_blocknr=8 [ 399.907471][T15342] b_state=0x00000029, b_size=512 [ 399.912506][T15342] device loop0 blocksize: 4096 This patch reduces frequency to up to once per a second, in addition to concatenating three lines into one. [ 399.866302][T15342] __find_get_block_slow() failed. block=1, b_blocknr=8, b_state=0x00000029, b_size=512, device loop0 blocksize: 4096 Signed-off-by:
Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Reviewed-by:
Jan Kara <jack@suse.cz> Cc: Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
-
Keith Busch authored
[ Upstream commit 5c959d73 ] A surprise removal may fail to tear down request queues if it is racing with the initial asynchronous probe. If that happens, the remove path won't see the queue resources to tear down, and the controller reset path may create a new request queue on a removed device, but will not be able to make forward progress, deadlocking the pci removal. Protect setting up non-blocking resources from a shutdown by holding the same mutex, and transition to the CONNECTING state after these resources are initialized so the probe path may see the dead controller state before dispatching new IO. Link: https://bugzilla.kernel.org/show_bug.cgi?id=202081Reported-by:
Alex Gagniuc <Alex_Gagniuc@Dellteam.com> Signed-off-by:
Alex Gagniuc <mr.nuke.me@gmail.com> Signed-off-by:
-
Keith Busch authored
[ Upstream commit e7ad43c3 ] If a controller supports the NS Change Notification, the namespace scan_work is automatically triggered after attaching a new namespace. Occasionally the namespace scan_work may append the new namespace to the list before the admin command effects handling is completed. The effects handling unfreezes namespaces, but if it unfreezes the newly attached namespace, its request_queue freeze depth will be off and we'll hit the warning in blk_mq_unfreeze_queue(). On the next namespace add, we will fail to freeze that queue due to the previous bad accounting and deadlock waiting for frozen. Fix that by preventing scan work from altering the namespace list while command effects handling needs to pair freeze with unfreeze. Reported-by:
Wen Xiong <wenxiong@us.ibm.com> Tested-by:
Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com> Signed-off-by:
-
Philip Yang authored
[ Upstream commit 0a5f49cb ] amdgpu_vm_get_task_info is called from interrupt handler and sched timeout workqueue, we should use irq version spin_lock to avoid deadlock. Signed-off-by:
Philip Yang <Philip.Yang@amd.com> Reviewed-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Tony Lindgren authored
[ Upstream commit c6e2bd95 ] We currently get the following error with pixcir_ts driver during a suspend resume cycle: omap_i2c 4802a000.i2c: controller timed out pixcir_ts 1-005c: pixcir_int_enable: can't read reg 0x34 : -110 pixcir_ts 1-005c: Failed to disable interrupt generation: -110 pixcir_ts 1-005c: Failed to stop dpm_run_callback(): pixcir_i2c_ts_resume+0x0/0x98 [pixcir_i2c_ts] returns -110 PM: Device 1-005c failed to resume: error -110 And at least am437x based devices with pixcir_ts will fail to resume to a touchscreen that is configured as the wakeup-source in device tree for these devices. This is because pixcir_ts tries to reconfigure it's registers for noirq suspend which fails. This also leaves i2c-omap in enabled state for suspend. Let's fix the pixcir_ts issue and make sure i2c-omap is suspended by adding SET_NOIRQ_SYSTEM_SLEEP_PM_OPS. Let's also get rid of some ifdefs while at it and replace them with __maybe_unused as SET_RUNTIME_PM_OPS and SET_NOIRQ_SYSTEM_SLEEP_PM_OPS already deal with the various PM Kconfig options. Reported-by:
Keerthy <j-keerthy@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com> Acked-by:
Vignesh R <vigneshr@ti.com> Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Ross Lagerwall authored
[ Upstream commit d8f6382a ] This reverts commit bbc0f8bd. It added a warning whose intent was to check whether the rport was still linked into the peer list. It doesn't work as intended and gives false positive warnings for two reasons: 1) If the rport is never linked into the peer list it will not be considered empty since the list_head is never initialized. 2) If the rport is deleted from the peer list using list_del_rcu(), then the list_head is in an undefined state and it is not considered empty. Signed-off-by:
Ross Lagerwall <ross.lagerwall@citrix.com> Reviewed-by:
Hannes Reinecke <hare@suse.com> Signed-off-by:
-
Jun-Ru Chang authored
[ Upstream commit 2b424cfc ] Patch (b6c7a324 "MIPS: Fix get_frame_info() handling of microMIPS function size.") introduces additional function size check for microMIPS by only checking insn between ip and ip + func_size. However, func_size in get_frame_info() is always 0 if KALLSYMS is not enabled. This causes get_frame_info() to return immediately without calculating correct frame_size, which in turn causes "Can't analyze schedule() prologue" warning messages at boot time. This patch removes func_size check, and let the frame_size check run up to 128 insns for both MIPS and microMIPS. Signed-off-by:
Jun-Ru Chang <jrjang@realtek.com> Signed-off-by:
Tony Wu <tonywu@realtek.com> Signed-off-by:
Paul Burton <paul.burton@mips.com> Fixes: b6c7a324 ("MIPS: Fix get_frame_info() handling of microMIPS function size.") Cc: <ralf@linux-mips.org> Cc: <jhogan@kernel.org> Cc: <macro@mips.com> Cc: <yamada.masahiro@socionext.com> Cc: <peterz@infradead.org> Cc: <mingo@kernel.org> Cc: <linux-mips@vger.kernel.org> Cc: <linux-kernel@vger.kernel.org> Signed-off-by:
-
Arnaldo Carvalho de Melo authored
[ Upstream commit 6ab3bc24 ] With a suitably defined "probe:vfs_getname" probe, 'perf trace' can "beautify" its output, so syscalls like open() or openat() can print the "filename" argument instead of just its hex address, like: $ perf trace -e open -- touch /dev/null [...] 0.590 ( 0.014 ms): touch/18063 open(filename: /dev/null, flags: CREAT|NOCTTY|NONBLOCK|WRONLY, mode: IRUGO|IWUGO) = 3 [...] The output without such beautifier looks like: 0.529 ( 0.011 ms): touch/18075 open(filename: 0xc78cf288, flags: CREAT|NOCTTY|NONBLOCK|WRONLY, mode: IRUGO|IWUGO) = 3 However, when the vfs_getname probe expands to multiple probes and it is not the first one that is hit, the beautifier fails, as following: 0.326 ( 0.010 ms): touch/18072 open(filename: , flags: CREAT|NOCTTY|NONBLOCK|WRONLY, mode: IRUGO|IWUGO) = 3 Fix it by hooking into all the expanded probes (inlines), now, for instance: [root@quaco ~]# perf probe -l probe:vfs_getname (on getname_flags:73@fs/namei.c with pathname) probe:vfs_getname_1 (on getname_flags:73@fs/namei.c with pathname) [root@quaco ~]# perf trace -e open* sleep 1 0.010 ( 0.005 ms): sleep/5588 openat(dfd: CWD, filename: /etc/ld.so.cache, flags: RDONLY|CLOEXEC) = 3 0.029 ( 0.006 ms): sleep/5588 openat(dfd: CWD, filename: /lib64/libc.so.6, flags: RDONLY|CLOEXEC) = 3 0.194 ( 0.008 ms): sleep/5588 openat(dfd: CWD, filename: /usr/lib/locale/locale-archive, flags: RDONLY|CLOEXEC) = 3 [root@quaco ~]# Works, further verified with: [root@quaco ~]# perf test vfs 65: Use vfs_getname probe to get syscall args filenames : Ok 66: Add vfs_getname probe to get syscall args filenames : Ok 67: Check open filename arg using perf trace + vfs_getname: Ok [root@quaco ~]# Reported-by:
Michael Petlan <mpetlan@redhat.com> Tested-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Jiri Olsa authored
[ Upstream commit 59a17706 ] When perf is built with the annobin plugin (RHEL8 build) extra symbols are added to its binary: # nm perf | grep annobin | head -10 0000000000241100 t .annobin_annotate.c 0000000000326490 t .annobin_annotate.c 0000000000249255 t .annobin_annotate.c_end 00000000003283a8 t .annobin_annotate.c_end 00000000001bce18 t .annobin_annotate.c_end.hot 00000000001bce18 t .annobin_annotate.c_end.hot 00000000001bc3e2 t .annobin_annotate.c_end.unlikely 00000000001bc400 t .annobin_annotate.c_end.unlikely 00000000001bce18 t .annobin_annotate.c.hot 00000000001bce18 t .annobin_annotate.c.hot ... Those symbols have no use for report or annotation and should be skipped. Moreover they interfere with the DWARF unwind test on the PPC arch, where they are mixed with checked symbols and then the test fails: # perf test dwarf -v 59: Test dwarf unwind : --- start --- test child forked, pid 8515 unwind: .annobin_dwarf_unwind.c:ip = 0x10dba40dc (0x2740dc) ... got: .annobin_dwarf_unwind.c 0x10dba40dc, expecting test__arch_unwind_sample unwind: failed with 'no error' The annobin symbols are defined as NOTYPE/LOCAL/HIDDEN: # readelf -s ./perf | grep annobin | head -1 40: 00000000001bce4f 0 NOTYPE LOCAL HIDDEN 13 .annobin_init.c They can still pass the check for the label symbol. Adding check for HIDDEN and INTERNAL (as suggested by Nick below) visibility and filter out such symbols. > Just to be awkward, if you are going to ignore STV_HIDDEN > symbols then you should probably also ignore STV_INTERNAL ones > as well... Annobin does not generate them, but you never know, > one day some other tool might create some. Signed-off-by:
Jiri Olsa <jolsa@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Michael Petlan <mpetlan@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Nick Clifton <nickc@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20190128133526.GD15461@kravaSigned-off-by:
-
Julian Wiedmann authored
[ Upstream commit c2780c1a ] A card's close_dev work is scheduled on a driver-wide workqueue. If the card is removed and freed while the work is still active, this causes a use-after-free. So make sure that the work is completed before freeing the card. Fixes: 0f54761d ("qeth: Support VEPA mode") Signed-off-by:
Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by:
-
Julian Wiedmann authored
[ Upstream commit afa0c590 ] The error path in qeth_alloc_qdio_buffers() that takes care of cleaning up the Output Queues is buggy. It first frees the queue, but then calls qeth_clear_outq_buffers() with that very queue struct. Make the call to qeth_clear_outq_buffers() part of the free action (in the correct order), and while at it fix the naming of the helper. Fixes: 0da9581d ("qeth: exploit asynchronous delivery of storage blocks") Signed-off-by:
Alexandra Winter <wintera@linux.ibm.com> Signed-off-by:
-
Julian Wiedmann authored
[ Upstream commit 5065b2dd ] Whenever we fail before/while starting an IO, make sure to release the IO buffer. Usually qeth_irq() would do this for us, but if the IO doesn't even start we obviously won't get an interrupt for it either. Signed-off-by:
-
Martynas Pumputis authored
[ Upstream commit 4e35c1cb ] It is possible that two concurrent packets originating from the same socket of a connection-less protocol (e.g. UDP) can end up having different IP_CT_DIR_REPLY tuples which results in one of the packets being dropped. To illustrate this, consider the following simplified scenario: 1. Packet A and B are sent at the same time from two different threads by same UDP socket. No matching conntrack entry exists yet. Both packets cause allocation of a new conntrack entry. 2. get_unique_tuple gets called for A. No clashing entry found. conntrack entry for A is added to main conntrack table. 3. get_unique_tuple is called for B and will find that the reply tuple of B is already taken by A. It will allocate a new UDP source port for B to resolve the clash. 4. conntrack entry for B cannot be added to main conntrack table because its ORIGINAL direction is clashing with A and the REPLY directions of A and B are not the same anymore due to UDP source port reallocation done in step 3. This patch modifies nf_conntrack_tuple_taken so it doesn't consider colliding reply tuples if the IP_CT_DIR_ORIGINAL tuples are equal. [ Florian: simplify patch to not use .allow_clash setting and always ignore identical flows ] Signed-off-by:
Martynas Pumputis <martynas@weave.works> Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
Florian Westphal authored
[ Upstream commit 98bfc341 ] Check basic nat/redirect/masquerade for ipv4 and ipv6. Signed-off-by:
-
Naresh Kamboju authored
[ Upstream commit 952b72f8 ] In selftests the config fragment for netfilter was added as NF_TABLES_INET=y and this patch correct it as CONFIG_NF_TABLES_INET=y Signed-off-by:
Naresh Kamboju <naresh.kamboju@linaro.org> Acked-by:
-
Andy Shevchenko authored
[ Upstream commit 6454368a ] In case of mapping error the DMA addresses are invalid and continuing will screw system memory or potentially something else. [ 222.480310] dmatest: dma0chan7-copy0: summary 1 tests, 3 failures 6 iops 349 KB/s (0) ... [ 240.912725] check: Corrupted low memory at 00000000c7c75ac9 (2940 phys) = 5656000000000000 [ 240.921998] check: Corrupted low memory at 000000005715a1cd (2948 phys) = 279f2aca5595ab2b [ 240.931280] check: Corrupted low memory at 000000002f4024c0 (2950 phys) = 5e5624f349e793cf ... Abort any test if mapping failed. Fixes: 4076e755 ("dmatest: convert to dmaengine_unmap_data") Cc: Dan Williams <dan.j.williams@intel.com> Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
Vinod Koul <vkoul@kernel.org> Signed-off-by:
-
Stefano Garzarella authored
[ Upstream commit 85965487 ] When the virtio transport device disappear, we should reset all connected sockets in order to inform the users. Signed-off-by:
Stefano Garzarella <sgarzare@redhat.com> Reviewed-by:
Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by:
-
Stefano Garzarella authored
[ Upstream commit 22b5c0b6 ] virtio_vsock_remove() invokes the vsock_core_exit() also if there are opened sockets for the AF_VSOCK protocol family. In this way the vsock "transport" pointer is set to NULL, triggering the kernel panic at the first socket activity. This patch move the vsock_core_init()/vsock_core_exit() in the virtio_vsock respectively in module_init and module_exit functions, that cannot be invoked until there are open sockets. Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1609699Reported-by:
Yan Fu <yafu@redhat.com> Signed-off-by:
-
Codrin Ciubotariu authored
[ Upstream commit dc3f595b ] atchan->status variable is used to store two different information: - pass channel interrupts status from interrupt handler to tasklet; - channel information like whether it is cyclic or paused; This causes a bug when device_terminate_all() is called, (AT_XDMAC_CHAN_IS_CYCLIC cleared on atchan->status) and then a late End of Block interrupt arrives (AT_XDMAC_CIS_BIS), which sets bit 0 of atchan->status. Bit 0 is also used for AT_XDMAC_CHAN_IS_CYCLIC, so when a new descriptor for a cyclic transfer is created, the driver reports the channel as in use: if (test_and_set_bit(AT_XDMAC_CHAN_IS_CYCLIC, &atchan->status)) { dev_err(chan2dev(chan), "channel currently used\n"); return NULL; } This patch fixes the bug by adding a different struct member to keep the interrupts status separated from the channel status bits. Fixes: e1f7c9ee ("dmaengine: at_xdmac: creation of the atmel eXtended DMA Controller driver") Signed-off-by:
Codrin Ciubotariu <codrin.ciubotariu@microchip.com> Acked-by:
Ludovic Desroches <ludovic.desroches@microchip.com> Signed-off-by:
-
Paul Kocialkowski authored
[ Upstream commit b14e945b ] When initializing clocks, a reference to the TCON channel 0 clock is obtained. However, the clock is never prepared and enabled later. Switching from simplefb to DRM actually disables the clock (that was usually configured by U-Boot) because of that. On the V3s, this results in a hang when writing to some mixer registers when switching over to DRM from simplefb. Fix this by preparing and enabling the clock when initializing other clocks. Waiting for sun4i_tcon_channel_enable to enable the clock is apparently too late and results in the same mixer register access hang. Signed-off-by:
Paul Kocialkowski <paul.kocialkowski@bootlin.com> Signed-off-by:
Maxime Ripard <maxime.ripard@bootlin.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190131132550.26355-1-paul.kocialkowski@bootlin.comSigned-off-by:
-
Martin KaFai Lau authored
[ Upstream commit 7c4cd051 ] The map_lookup_elem used to not acquiring spinlock in order to optimize the reader. It was true until commit 557c0c6e ("bpf: convert stackmap to pre-allocation") The syscall's map_lookup_elem(stackmap) calls bpf_stackmap_copy(). bpf_stackmap_copy() may find the elem no longer needed after the copy is done. If that is the case, pcpu_freelist_push() saves this elem for reuse later. This push requires a spinlock. If a tracing bpf_prog got run in the middle of the syscall's map_lookup_elem(stackmap) and this tracing bpf_prog is calling bpf_get_stackid(stackmap) which also requires the same pcpu_freelist's spinlock, it may end up with a dead lock situation as reported by Eric Dumazet in https://patchwork.ozlabs.org/patch/1030266/ The situation is the same as the syscall's map_update_elem() which needs to acquire the pcpu_freelist's spinlock and could race with tracing bpf_prog. Hence, this patch fixes it by protecting bpf_stackmap_copy() with this_cpu_inc(bpf_prog_active) to prevent tracing bpf_prog from running. A later syscall's map_lookup_elem commit f1a2e44a ("bpf: add queue and stack maps") also acquires a spinlock and races with tracing bpf_prog similarly. Hence, this patch is forward looking and protects the majority of the map lookups. bpf_map_offload_lookup_elem() is the exception since it is for network bpf_prog only (i.e. never called by tracing bpf_prog). Fixes: 557c0c6e ("bpf: convert stackmap to pre-allocation") Reported-by:
Eric Dumazet <eric.dumazet@gmail.com> Acked-by:
Alexei Starovoitov <ast@kernel.org> Signed-off-by:
Martin KaFai Lau <kafai@fb.com> Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
-
Alexei Starovoitov authored
[ Upstream commit e16ec340 ] Lockdep found a potential deadlock between cpu_hotplug_lock, bpf_event_mutex, and cpuctx_mutex: [ 13.007000] WARNING: possible circular locking dependency detected [ 13.007587] 5.0.0-rc3-00018-g2fa53f89-dirty #477 Not tainted [ 13.008124] ------------------------------------------------------ [ 13.008624] test_progs/246 is trying to acquire lock: [ 13.009030] 0000000094160d1d (tracepoints_mutex){+.+.}, at: tracepoint_probe_register_prio+0x2d/0x300 [ 13.009770] [ 13.009770] but task is already holding lock: [ 13.010239] 00000000d663ef86 (bpf_event_mutex){+.+.}, at: bpf_probe_register+0x1d/0x60 [ 13.010877] [ 13.010877] which lock already depends on the new lock. [ 13.010877] [ 13.011532] [ 13.011532] the existing dependency chain (in reverse order) is: [ 13.012129] [ 13.012129] -> #4 (bpf_event_mutex){+.+.}: [ 13.012582] perf_event_query_prog_array+0x9b/0x130 [ 13.013016] _perf_ioctl+0x3aa/0x830 [ 13.013354] perf_ioctl+0x2e/0x50 [ 13.013668] do_vfs_ioctl+0x8f/0x6a0 [ 13.014003] ksys_ioctl+0x70/0x80 [ 13.014320] __x64_sys_ioctl+0x16/0x20 [ 13.014668] do_syscall_64+0x4a/0x180 [ 13.015007] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 13.015469] [ 13.015469] -> #3 (&cpuctx_mutex){+.+.}: [ 13.015910] perf_event_init_cpu+0x5a/0x90 [ 13.016291] perf_event_init+0x1b2/0x1de [ 13.016654] start_kernel+0x2b8/0x42a [ 13.016995] secondary_startup_64+0xa4/0xb0 [ 13.017382] [ 13.017382] -> #2 (pmus_lock){+.+.}: [ 13.017794] perf_event_init_cpu+0x21/0x90 [ 13.018172] cpuhp_invoke_callback+0xb3/0x960 [ 13.018573] _cpu_up+0xa7/0x140 [ 13.018871] do_cpu_up+0xa4/0xc0 [ 13.019178] smp_init+0xcd/0xd2 [ 13.019483] kernel_init_freeable+0x123/0x24f [ 13.019878] kernel_init+0xa/0x110 [ 13.020201] ret_from_fork+0x24/0x30 [ 13.020541] [ 13.020541] -> #1 (cpu_hotplug_lock.rw_sem){++++}: [ 13.021051] static_key_slow_inc+0xe/0x20 [ 13.021424] tracepoint_probe_register_prio+0x28c/0x300 [ 13.021891] perf_trace_event_init+0x11f/0x250 [ 13.022297] perf_trace_init+0x6b/0xa0 [ 13.022644] perf_tp_event_init+0x25/0x40 [ 13.023011] perf_try_init_event+0x6b/0x90 [ 13.023386] perf_event_alloc+0x9a8/0xc40 [ 13.023754] __do_sys_perf_event_open+0x1dd/0xd30 [ 13.024173] do_syscall_64+0x4a/0x180 [ 13.024519] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 13.024968] [ 13.024968] -> #0 (tracepoints_mutex){+.+.}: [ 13.025434] __mutex_lock+0x86/0x970 [ 13.025764] tracepoint_probe_register_prio+0x2d/0x300 [ 13.026215] bpf_probe_register+0x40/0x60 [ 13.026584] bpf_raw_tracepoint_open.isra.34+0xa4/0x130 [ 13.027042] __do_sys_bpf+0x94f/0x1a90 [ 13.027389] do_syscall_64+0x4a/0x180 [ 13.027727] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 13.028171] [ 13.028171] other info that might help us debug this: [ 13.028171] [ 13.028807] Chain exists of: [ 13.028807] tracepoints_mutex --> &cpuctx_mutex --> bpf_event_mutex [ 13.028807] [ 13.029666] Possible unsafe locking scenario: [ 13.029666] [ 13.030140] CPU0 CPU1 [ 13.030510] ---- ---- [ 13.030875] lock(bpf_event_mutex); [ 13.031166] lock(&cpuctx_mutex); [ 13.031645] lock(bpf_event_mutex); [ 13.032135] lock(tracepoints_mutex); [ 13.032441] [ 13.032441] *** DEADLOCK *** [ 13.032441] [ 13.032911] 1 lock held by test_progs/246: [ 13.033239] #0: 00000000d663ef86 (bpf_event_mutex){+.+.}, at: bpf_probe_register+0x1d/0x60 [ 13.033909] [ 13.033909] stack backtrace: [ 13.034258] CPU: 1 PID: 246 Comm: test_progs Not tainted 5.0.0-rc3-00018-g2fa53f89-dirty #477 [ 13.034964] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-2.el7 04/01/2014 [ 13.035657] Call Trace: [ 13.035859] dump_stack+0x5f/0x8b [ 13.036130] print_circular_bug.isra.37+0x1ce/0x1db [ 13.036526] __lock_acquire+0x1158/0x1350 [ 13.036852] ? lock_acquire+0x98/0x190 [ 13.037154] lock_acquire+0x98/0x190 [ 13.037447] ? tracepoint_probe_register_prio+0x2d/0x300 [ 13.037876] __mutex_lock+0x86/0x970 [ 13.038167] ? tracepoint_probe_register_prio+0x2d/0x300 [ 13.038600] ? tracepoint_probe_register_prio+0x2d/0x300 [ 13.039028] ? __mutex_lock+0x86/0x970 [ 13.039337] ? __mutex_lock+0x24a/0x970 [ 13.039649] ? bpf_probe_register+0x1d/0x60 [ 13.039992] ? __bpf_trace_sched_wake_idle_without_ipi+0x10/0x10 [ 13.040478] ? tracepoint_probe_register_prio+0x2d/0x300 [ 13.040906] tracepoint_probe_register_prio+0x2d/0x300 [ 13.041325] bpf_probe_register+0x40/0x60 [ 13.041649] bpf_raw_tracepoint_open.isra.34+0xa4/0x130 [ 13.042068] ? __might_fault+0x3e/0x90 [ 13.042374] __do_sys_bpf+0x94f/0x1a90 [ 13.042678] do_syscall_64+0x4a/0x180 [ 13.042975] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 13.043382] RIP: 0033:0x7f23b10a07f9 [ 13.045155] RSP: 002b:00007ffdef42fdd8 EFLAGS: 00000202 ORIG_RAX: 0000000000000141 [ 13.045759] RAX: ffffffffffffffda RBX: 00007ffdef42ff70 RCX: 00007f23b10a07f9 [ 13.046326] RDX: 0000000000000070 RSI: 00007ffdef42fe10 RDI: 0000000000000011 [ 13.046893] RBP: 00007ffdef42fdf0 R08: 0000000000000038 R09: 00007ffdef42fe10 [ 13.047462] R10: 0000000000000000 R11: 0000000000000202 R12: 0000000000000000 [ 13.048029] R13: 0000000000000016 R14: 00007f23b1db4690 R15: 0000000000000000 Since tracepoints_mutex will be taken in tracepoint_probe_register/unregister() there is no need to take bpf_event_mutex too. bpf_event_mutex is protecting modifications to prog array used in kprobe/perf bpf progs. bpf_raw_tracepoints don't need to take this mutex. Fixes: c4f6699d ("bpf: introduce BPF_RAW_TRACEPOINT") Acked-by:
-
Alexei Starovoitov authored
[ Upstream commit a89fac57 ] Lockdep warns about false positive: [ 12.492084] 00000000e6b28347 (&head->lock){+...}, at: pcpu_freelist_push+0x2a/0x40 [ 12.492696] but this lock was taken by another, HARDIRQ-safe lock in the past: [ 12.493275] (&rq->lock){-.-.} [ 12.493276] [ 12.493276] [ 12.493276] and interrupts could create inverse lock ordering between them. [ 12.493276] [ 12.494435] [ 12.494435] other info that might help us debug this: [ 12.494979] Possible interrupt unsafe locking scenario: [ 12.494979] [ 12.495518] CPU0 CPU1 [ 12.495879] ---- ---- [ 12.496243] lock(&head->lock); [ 12.496502] local_irq_disable(); [ 12.496969] lock(&rq->lock); [ 12.497431] lock(&head->lock); [ 12.497890] <Interrupt> [ 12.498104] lock(&rq->lock); [ 12.498368] [ 12.498368] *** DEADLOCK *** [ 12.498368] [ 12.498837] 1 lock held by dd/276: [ 12.499110] #0: 00000000c58cb2ee (rcu_read_lock){....}, at: trace_call_bpf+0x5e/0x240 [ 12.499747] [ 12.499747] the shortest dependencies between 2nd lock and 1st lock: [ 12.500389] -> (&rq->lock){-.-.} { [ 12.500669] IN-HARDIRQ-W at: [ 12.500934] _raw_spin_lock+0x2f/0x40 [ 12.501373] scheduler_tick+0x4c/0xf0 [ 12.501812] update_process_times+0x40/0x50 [ 12.502294] tick_periodic+0x27/0xb0 [ 12.502723] tick_handle_periodic+0x1f/0x60 [ 12.503203] timer_interrupt+0x11/0x20 [ 12.503651] __handle_irq_event_percpu+0x43/0x2c0 [ 12.504167] handle_irq_event_percpu+0x20/0x50 [ 12.504674] handle_irq_event+0x37/0x60 [ 12.505139] handle_level_irq+0xa7/0x120 [ 12.505601] handle_irq+0xa1/0x150 [ 12.506018] do_IRQ+0x77/0x140 [ 12.506411] ret_from_intr+0x0/0x1d [ 12.506834] _raw_spin_unlock_irqrestore+0x53/0x60 [ 12.507362] __setup_irq+0x481/0x730 [ 12.507789] setup_irq+0x49/0x80 [ 12.508195] hpet_time_init+0x21/0x32 [ 12.508644] x86_late_time_init+0xb/0x16 [ 12.509106] start_kernel+0x390/0x42a [ 12.509554] secondary_startup_64+0xa4/0xb0 [ 12.510034] IN-SOFTIRQ-W at: [ 12.510305] _raw_spin_lock+0x2f/0x40 [ 12.510772] try_to_wake_up+0x1c7/0x4e0 [ 12.511220] swake_up_locked+0x20/0x40 [ 12.511657] swake_up_one+0x1a/0x30 [ 12.512070] rcu_process_callbacks+0xc5/0x650 [ 12.512553] __do_softirq+0xe6/0x47b [ 12.512978] irq_exit+0xc3/0xd0 [ 12.513372] smp_apic_timer_interrupt+0xa9/0x250 [ 12.513876] apic_timer_interrupt+0xf/0x20 [ 12.514343] default_idle+0x1c/0x170 [ 12.514765] do_idle+0x199/0x240 [ 12.515159] cpu_startup_entry+0x19/0x20 [ 12.515614] start_kernel+0x422/0x42a [ 12.516045] secondary_startup_64+0xa4/0xb0 [ 12.516521] INITIAL USE at: [ 12.516774] _raw_spin_lock_irqsave+0x38/0x50 [ 12.517258] rq_attach_root+0x16/0xd0 [ 12.517685] sched_init+0x2f2/0x3eb [ 12.518096] start_kernel+0x1fb/0x42a [ 12.518525] secondary_startup_64+0xa4/0xb0 [ 12.518986] } [ 12.519132] ... key at: [<ffffffff82b7bc28>] __key.71384+0x0/0x8 [ 12.519649] ... acquired at: [ 12.519892] pcpu_freelist_pop+0x7b/0xd0 [ 12.520221] bpf_get_stackid+0x1d2/0x4d0 [ 12.520563] ___bpf_prog_run+0x8b4/0x11a0 [ 12.520887] [ 12.521008] -> (&head->lock){+...} { [ 12.521292] HARDIRQ-ON-W at: [ 12.521539] _raw_spin_lock+0x2f/0x40 [ 12.521950] pcpu_freelist_push+0x2a/0x40 [ 12.522396] bpf_get_stackid+0x494/0x4d0 [ 12.522828] ___bpf_prog_run+0x8b4/0x11a0 [ 12.523296] INITIAL USE at: [ 12.523537] _raw_spin_lock+0x2f/0x40 [ 12.523944] pcpu_freelist_populate+0xc0/0x120 [ 12.524417] htab_map_alloc+0x405/0x500 [ 12.524835] __do_sys_bpf+0x1a3/0x1a90 [ 12.525253] do_syscall_64+0x4a/0x180 [ 12.525659] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 12.526167] } [ 12.526311] ... key at: [<ffffffff838f7668>] __key.13130+0x0/0x8 [ 12.526812] ... acquired at: [ 12.527047] __lock_acquire+0x521/0x1350 [ 12.527371] lock_acquire+0x98/0x190 [ 12.527680] _raw_spin_lock+0x2f/0x40 [ 12.527994] pcpu_freelist_push+0x2a/0x40 [ 12.528325] bpf_get_stackid+0x494/0x4d0 [ 12.528645] ___bpf_prog_run+0x8b4/0x11a0 [ 12.528970] [ 12.529092] [ 12.529092] stack backtrace: [ 12.529444] CPU: 0 PID: 276 Comm: dd Not tainted 5.0.0-rc3-00018-g2fa53f89 #475 [ 12.530043] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-2.el7 04/01/2014 [ 12.530750] Call Trace: [ 12.530948] dump_stack+0x5f/0x8b [ 12.531248] check_usage_backwards+0x10c/0x120 [ 12.531598] ? ___bpf_prog_run+0x8b4/0x11a0 [ 12.531935] ? mark_lock+0x382/0x560 [ 12.532229] mark_lock+0x382/0x560 [ 12.532496] ? print_shortest_lock_dependencies+0x180/0x180 [ 12.532928] __lock_acquire+0x521/0x1350 [ 12.533271] ? find_get_entry+0x17f/0x2e0 [ 12.533586] ? find_get_entry+0x19c/0x2e0 [ 12.533902] ? lock_acquire+0x98/0x190 [ 12.534196] lock_acquire+0x98/0x190 [ 12.534482] ? pcpu_freelist_push+0x2a/0x40 [ 12.534810] _raw_spin_lock+0x2f/0x40 [ 12.535099] ? pcpu_freelist_push+0x2a/0x40 [ 12.535432] pcpu_freelist_push+0x2a/0x40 [ 12.535750] bpf_get_stackid+0x494/0x4d0 [ 12.536062] ___bpf_prog_run+0x8b4/0x11a0 It has been explained that is a false positive here: https://lkml.org/lkml/2018/7/25/756 Recap: - stackmap uses pcpu_freelist - The lock in pcpu_freelist is a percpu lock - stackmap is only used by tracing bpf_prog - A tracing bpf_prog cannot be run if another bpf_prog has already been running (ensured by the percpu bpf_prog_active counter). Eric pointed out that this lockdep splats stops other legit lockdep splats in selftests/bpf/test_progs.c. Fix this by calling local_irq_save/restore for stackmap. Another false positive had also been worked around by calling local_irq_save in commit 89ad2fa3 ("bpf: fix lockdep splat"). That commit added unnecessary irq_save/restore to fast path of bpf hash map. irqs are already disabled at that point, since htab is holding per bucket spin_lock with irqsave. Let's reduce overhead for htab by introducing __pcpu_freelist_push/pop function w/o irqsave and convert pcpu_freelist_push/pop to irqsave to be used elsewhere (right now only in stackmap). It stops lockdep false positive in stackmap with a bit of acceptable overhead. Fixes: 557c0c6e ("bpf: convert stackmap to pre-allocation") Reported-by:
-
Martynas Pumputis authored
[ Upstream commit 1bb54c40 ] Previously, bpf_num_possible_cpus() had a bug when calculating a number of possible CPUs in the case of sparse CPU allocations, as it was considering only the first range or element of /sys/devices/system/cpu/possible. E.g. in the case of "0,2-3" (CPU 1 is not available), the function returned 1 instead of 3. This patch fixes the function by making it parse all CPU ranges and elements. Signed-off-by:
Martynas Pumputis <m@lambda.lt> Acked-by:
Yonghong Song <yhs@fb.com> Signed-off-by:
-
Greg Kroah-Hartman authored
[ Upstream commit 2c1cf00e ] If create_buf_file() returns an error, don't try to reference it later as a valid dentry pointer. This problem was exposed when debugfs started to return errors instead of just NULL for some calls when they do not succeed properly. Also, the check for WARN_ON(dentry) was just wrong :) Reported-by:
Kees Cook <keescook@chromium.org> Reported-and-tested-by: syzbot+16c3a70e1e9b29346c43@syzkaller.appspotmail.com Reported-by:
-
Zenghui Yu authored
[ Upstream commit 56841070 ] According to ARM IHI 0069C (ID070116), we should use GITS_TYPER's bits [7:4] as ITT_entry_size instead of [8:4]. Although this is pretty annoying, it only results in a potential over-allocation of memory, and nothing bad happens. Fixes: 3dfa576b ("irqchip/gic-v3-its: Add probing for VLPI properties") Signed-off-by:
Zenghui Yu <yuzenghui@huawei.com> [maz: massaged subject and commit message] Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
-
Jose Abreu authored
[ Upstream commit e2cd682d ] In stmmac xmit callback we use a different flow for TSO packets but TSO xmit callback is not disabling the EEE mode. Fix this by disabling earlier the EEE mode, i.e. before calling the TSO xmit callback. Signed-off-by:
Jose Abreu <joabreu@synopsys.com> Cc: Joao Pinto <jpinto@synopsys.com> Cc: David S. Miller <davem@davemloft.net> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by:
-
Jose Abreu authored
[ Upstream commit c5acdbee ] The number of TSO enabled channels in HW can be different than the number of total channels. There is no way to determined, at runtime, the number of TSO capable channels and its safe to assume that if TSO is enabled then at least channel 0 will be TSO capable. Lets always send TSO packets from Queue 0. Signed-off-by:
-
