- 25 Aug, 2019 29 commits
-
-
YueHaibing authored
[ Upstream commit 09e088a4 ] Fixes gcc '-Wunused-but-set-variable' warning: drivers/xen/xen-pciback/conf_space_capability.c: In function pm_ctrl_write: drivers/xen/xen-pciback/conf_space_capability.c:119:25: warning: variable old_state set but not used [-Wunused-but-set-variable] It is never used so can be removed. Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Reviewed-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by:
Juergen Gross <jgross@suse.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Geert Uytterhoeven authored
[ Upstream commit e1f1ae80 ] The module reset code in the Renesas CPG/MSSR driver uses read-modify-write (RMW) operations to write to a Software Reset Register (SRCRn), and simple writes to write to a Software Reset Clearing Register (SRSTCLRn), as was mandated by the R-Car Gen2 and Gen3 Hardware User's Manuals. However, this may cause a race condition when two devices are reset in parallel: if the reset for device A completes in the middle of the RMW operation for device B, device A may be reset again, causing subtle failures (e.g. i2c timeouts): thread A thread B -------- -------- val = SRCRn val |= bit A SRCRn = val delay val = SRCRn (bit A is set) SRSTCLRn = bit A (bit A in SRCRn is cleared) val |= bit B SRCRn = val (bit A and B are set) This can be reproduced on e.g. Salvator-XS using: $ while true; do i2cdump -f -y 4 0x6A b > /dev/null; done & $ while true; do i2cdump -f -y 2 0x10 b > /dev/null; done & i2c-rcar e6510000.i2c: error -110 : 40000002 i2c-rcar e66d8000.i2c: error -110 : 40000002 According to the R-Car Gen3 Hardware Manual Errata for Rev. 0.80 of Feb 28, 2018, reflected in Rev. 1.00 of the R-Car Gen3 Hardware User's Manual, writes to SRCRn do not require read-modify-write cycles. Note that the R-Car Gen2 Hardware User's Manual has not been updated yet, and still says a read-modify-write sequence is required. According to the hardware team, the reset hardware block is the same on both R-Car Gen2 and Gen3, though. Hence fix the issue by replacing the read-modify-write operations on SRCRn by simple writes. Reported-by:
Yao Lihua <Lihua.Yao@desay-svautomotive.com> Fixes: 6197aa65 ("clk: renesas: cpg-mssr: Add support for reset control") Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Tested-by:
Linh Phung <linh.phung.jy@renesas.com> Signed-off-by:
Stephen Boyd <sboyd@kernel.org> Signed-off-by:
-
Chunyan Zhang authored
[ Upstream commit c9a67cbb ] Make REGMAP_MMIO selected to avoid undefined reference to regmap symbols. Fixes: d41f59fd ("clk: sprd: Add common infrastructure") Signed-off-by:
Chunyan Zhang <chunyan.zhang@unisoc.com> Signed-off-by:
-
Codrin Ciubotariu authored
[ Upstream commit 1573eebe ] In clk_generated_determine_rate(), if the divisor is greater than GENERATED_MAX_DIV + 1, then the wrong best_rate will be returned. If clk_generated_set_rate() will be called later with this wrong rate, it will return -EINVAL, so the generated clock won't change its value. Do no let the divisor be greater than GENERATED_MAX_DIV + 1. Fixes: 8c7aa632 ("clk: at91: clk-generated: remove useless divisor loop") Signed-off-by:
Codrin Ciubotariu <codrin.ciubotariu@microchip.com> Acked-by:
Nicolas Ferre <nicolas.ferre@microchip.com> Acked-by:
Ludovic Desroches <ludovic.desroches@microchip.com> Signed-off-by:
-
Vincent Chen authored
commit 69703eb9 upstream. Make the __fstate_clean() function correctly set the state of sstatus.FS in pt_regs to SR_FS_CLEAN. Fixes: 7db91e57 ("RISC-V: Task implementation") Cc: linux-stable <stable@vger.kernel.org> Signed-off-by:
Vincent Chen <vincent.chen@sifive.com> Reviewed-by:
Anup Patel <anup@brainfault.org> Reviewed-by:
Christoph Hellwig <hch@lst.de> [paul.walmsley@sifive.com: expanded "Fixes" commit ID] Signed-off-by:
Paul Walmsley <paul.walmsley@sifive.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Florian Westphal authored
commit 3b48300d upstream. ebtables doesn't include the base chain policies in the rule count, so we need to add them manually when we call into the x_tables core to allocate space for the comapt offset table. This lead syzbot to trigger: WARNING: CPU: 1 PID: 9012 at net/netfilter/x_tables.c:649 xt_compat_add_offset.cold+0x11/0x36 net/netfilter/x_tables.c:649 Reported-by: syzbot+276ddebab3382bbf72db@syzkaller.appspotmail.com Fixes: 2035f3ff ("netfilter: ebtables: compat: un-break 32bit setsockopt when no rules are present") Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
Denis Kirjanov authored
commit 224c0497 upstream. get_registers() may fail with -ENOMEM and in this case we can read a garbage from the status variable tmp. Reported-by: syzbot+3499a83b2d062ae409d4@syzkaller.appspotmail.com Signed-off-by:
Denis Kirjanov <kda@linux-powerpc.org> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Oliver Neukum authored
commit 849f5ae3 upstream. The endpoint type should also be checked before a device is accepted. Reported-by: syzbot+5efc10c005014d061a74@syzkaller.appspotmail.com Signed-off-by:
Oliver Neukum <oneukum@suse.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Oliver Neukum authored
commit c88090df upstream. The driver should check whether the endpoint it uses has the correct type. Reported-by: syzbot+c7df50363aaff50aa363@syzkaller.appspotmail.com Signed-off-by:
-
Hillf Danton authored
commit 6d4472d7 upstream. Undo what we did for opening before releasing the memory slice. Reported-by:
syzbot <syzbot+62a1e04fd3ec2abf099e@syzkaller.appspotmail.com> Cc: Andrey Konovalov <andreyknvl@google.com> Signed-off-by:
Hillf Danton <hdanton@sina.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Hillf Danton authored
commit 9c09b214 upstream. syzbot found the following crash on: HEAD commit: e96407b4 usb-fuzzer: main usb gadget fuzzer driver git tree: https://github.com/google/kasan.git usb-fuzzer console output: https://syzkaller.appspot.com/x/log.txt?x=147ac20c600000 kernel config: https://syzkaller.appspot.com/x/.config?x=792eb47789f57810 dashboard link: https://syzkaller.appspot.com/bug?extid=62a1e04fd3ec2abf099e compiler: gcc (GCC) 9.0.0 20181231 (experimental) ================================================================== BUG: KASAN: use-after-free in __lock_acquire+0x302a/0x3b50 kernel/locking/lockdep.c:3753 Read of size 8 at addr ffff8881cf591a08 by task syz-executor.1/26260 CPU: 1 PID: 26260 Comm: syz-executor.1 Not tainted 5.3.0-rc2+ #24 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0xca/0x13e lib/dump_stack.c:113 print_address_description+0x6a/0x32c mm/kasan/report.c:351 __kasan_report.cold+0x1a/0x33 mm/kasan/report.c:482 kasan_report+0xe/0x12 mm/kasan/common.c:612 __lock_acquire+0x302a/0x3b50 kernel/locking/lockdep.c:3753 lock_acquire+0x127/0x320 kernel/locking/lockdep.c:4412 __raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:110 [inline] _raw_spin_lock_irqsave+0x32/0x50 kernel/locking/spinlock.c:159 hiddev_release+0x82/0x520 drivers/hid/usbhid/hiddev.c:221 __fput+0x2d7/0x840 fs/file_table.c:280 task_work_run+0x13f/0x1c0 kernel/task_work.c:113 exit_task_work include/linux/task_work.h:22 [inline] do_exit+0x8ef/0x2c50 kernel/exit.c:878 do_group_exit+0x125/0x340 kernel/exit.c:982 get_signal+0x466/0x23d0 kernel/signal.c:2728 do_signal+0x88/0x14e0 arch/x86/kernel/signal.c:815 exit_to_usermode_loop+0x1a2/0x200 arch/x86/entry/common.c:159 prepare_exit_to_usermode arch/x86/entry/common.c:194 [inline] syscall_return_slowpath arch/x86/entry/common.c:274 [inline] do_syscall_64+0x45f/0x580 arch/x86/entry/common.c:299 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x459829 Code: fd b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 cb b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007f75b2a6ccf8 EFLAGS: 00000246 ORIG_RAX: 00000000000000ca RAX: fffffffffffffe00 RBX: 000000000075c078 RCX: 0000000000459829 RDX: 0000000000000000 RSI: 0000000000000080 RDI: 000000000075c078 RBP: 000000000075c070 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 000000000075c07c R13: 00007ffcdfe1023f R14: 00007f75b2a6d9c0 R15: 000000000075c07c Allocated by task 104: save_stack+0x1b/0x80 mm/kasan/common.c:69 set_track mm/kasan/common.c:77 [inline] __kasan_kmalloc mm/kasan/common.c:487 [inline] __kasan_kmalloc.constprop.0+0xbf/0xd0 mm/kasan/common.c:460 kmalloc include/linux/slab.h:552 [inline] kzalloc include/linux/slab.h:748 [inline] hiddev_connect+0x242/0x5b0 drivers/hid/usbhid/hiddev.c:900 hid_connect+0x239/0xbb0 drivers/hid/hid-core.c:1882 hid_hw_start drivers/hid/hid-core.c:1981 [inline] hid_hw_start+0xa2/0x130 drivers/hid/hid-core.c:1972 appleir_probe+0x13e/0x1a0 drivers/hid/hid-appleir.c:308 hid_device_probe+0x2be/0x3f0 drivers/hid/hid-core.c:2209 really_probe+0x281/0x650 drivers/base/dd.c:548 driver_probe_device+0x101/0x1b0 drivers/base/dd.c:709 __device_attach_driver+0x1c2/0x220 drivers/base/dd.c:816 bus_for_each_drv+0x15c/0x1e0 drivers/base/bus.c:454 __device_attach+0x217/0x360 drivers/base/dd.c:882 bus_probe_device+0x1e4/0x290 drivers/base/bus.c:514 device_add+0xae6/0x16f0 drivers/base/core.c:2114 hid_add_device+0x33c/0x990 drivers/hid/hid-core.c:2365 usbhid_probe+0xa81/0xfa0 drivers/hid/usbhid/hid-core.c:1386 usb_probe_interface+0x305/0x7a0 drivers/usb/core/driver.c:361 really_probe+0x281/0x650 drivers/base/dd.c:548 driver_probe_device+0x101/0x1b0 drivers/base/dd.c:709 __device_attach_driver+0x1c2/0x220 drivers/base/dd.c:816 bus_for_each_drv+0x15c/0x1e0 drivers/base/bus.c:454 __device_attach+0x217/0x360 drivers/base/dd.c:882 bus_probe_device+0x1e4/0x290 drivers/base/bus.c:514 device_add+0xae6/0x16f0 drivers/base/core.c:2114 usb_set_configuration+0xdf6/0x1670 drivers/usb/core/message.c:2023 generic_probe+0x9d/0xd5 drivers/usb/core/generic.c:210 usb_probe_device+0x99/0x100 drivers/usb/core/driver.c:266 really_probe+0x281/0x650 drivers/base/dd.c:548 driver_probe_device+0x101/0x1b0 drivers/base/dd.c:709 __device_attach_driver+0x1c2/0x220 drivers/base/dd.c:816 bus_for_each_drv+0x15c/0x1e0 drivers/base/bus.c:454 __device_attach+0x217/0x360 drivers/base/dd.c:882 bus_probe_device+0x1e4/0x290 drivers/base/bus.c:514 device_add+0xae6/0x16f0 drivers/base/core.c:2114 usb_new_device.cold+0x6a4/0xe79 drivers/usb/core/hub.c:2536 hub_port_connect drivers/usb/core/hub.c:5098 [inline] hub_port_connect_change drivers/usb/core/hub.c:5213 [inline] port_event drivers/usb/core/hub.c:5359 [inline] hub_event+0x1b5c/0x3640 drivers/usb/core/hub.c:5441 process_one_work+0x92b/0x1530 kernel/workqueue.c:2269 worker_thread+0x96/0xe20 kernel/workqueue.c:2415 kthread+0x318/0x420 kernel/kthread.c:255 ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:352 Freed by task 104: save_stack+0x1b/0x80 mm/kasan/common.c:69 set_track mm/kasan/common.c:77 [inline] __kasan_slab_free+0x130/0x180 mm/kasan/common.c:449 slab_free_hook mm/slub.c:1423 [inline] slab_free_freelist_hook mm/slub.c:1470 [inline] slab_free mm/slub.c:3012 [inline] kfree+0xe4/0x2f0 mm/slub.c:3953 hiddev_connect.cold+0x45/0x5c drivers/hid/usbhid/hiddev.c:914 hid_connect+0x239/0xbb0 drivers/hid/hid-core.c:1882 hid_hw_start drivers/hid/hid-core.c:1981 [inline] hid_hw_start+0xa2/0x130 drivers/hid/hid-core.c:1972 appleir_probe+0x13e/0x1a0 drivers/hid/hid-appleir.c:308 hid_device_probe+0x2be/0x3f0 drivers/hid/hid-core.c:2209 really_probe+0x281/0x650 drivers/base/dd.c:548 driver_probe_device+0x101/0x1b0 drivers/base/dd.c:709 __device_attach_driver+0x1c2/0x220 drivers/base/dd.c:816 bus_for_each_drv+0x15c/0x1e0 drivers/base/bus.c:454 __device_attach+0x217/0x360 drivers/base/dd.c:882 bus_probe_device+0x1e4/0x290 drivers/base/bus.c:514 device_add+0xae6/0x16f0 drivers/base/core.c:2114 hid_add_device+0x33c/0x990 drivers/hid/hid-core.c:2365 usbhid_probe+0xa81/0xfa0 drivers/hid/usbhid/hid-core.c:1386 usb_probe_interface+0x305/0x7a0 drivers/usb/core/driver.c:361 really_probe+0x281/0x650 drivers/base/dd.c:548 driver_probe_device+0x101/0x1b0 drivers/base/dd.c:709 __device_attach_driver+0x1c2/0x220 drivers/base/dd.c:816 bus_for_each_drv+0x15c/0x1e0 drivers/base/bus.c:454 __device_attach+0x217/0x360 drivers/base/dd.c:882 bus_probe_device+0x1e4/0x290 drivers/base/bus.c:514 device_add+0xae6/0x16f0 drivers/base/core.c:2114 usb_set_configuration+0xdf6/0x1670 drivers/usb/core/message.c:2023 generic_probe+0x9d/0xd5 drivers/usb/core/generic.c:210 usb_probe_device+0x99/0x100 drivers/usb/core/driver.c:266 really_probe+0x281/0x650 drivers/base/dd.c:548 driver_probe_device+0x101/0x1b0 drivers/base/dd.c:709 __device_attach_driver+0x1c2/0x220 drivers/base/dd.c:816 bus_for_each_drv+0x15c/0x1e0 drivers/base/bus.c:454 __device_attach+0x217/0x360 drivers/base/dd.c:882 bus_probe_device+0x1e4/0x290 drivers/base/bus.c:514 device_add+0xae6/0x16f0 drivers/base/core.c:2114 usb_new_device.cold+0x6a4/0xe79 drivers/usb/core/hub.c:2536 hub_port_connect drivers/usb/core/hub.c:5098 [inline] hub_port_connect_change drivers/usb/core/hub.c:5213 [inline] port_event drivers/usb/core/hub.c:5359 [inline] hub_event+0x1b5c/0x3640 drivers/usb/core/hub.c:5441 process_one_work+0x92b/0x1530 kernel/workqueue.c:2269 worker_thread+0x96/0xe20 kernel/workqueue.c:2415 kthread+0x318/0x420 kernel/kthread.c:255 ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:352 The buggy address belongs to the object at ffff8881cf591900 which belongs to the cache kmalloc-512 of size 512 The buggy address is located 264 bytes inside of 512-byte region [ffff8881cf591900, ffff8881cf591b00) The buggy address belongs to the page: page:ffffea00073d6400 refcount:1 mapcount:0 mapping:ffff8881da002500 index:0x0 compound_mapcount: 0 flags: 0x200000000010200(slab|head) raw: 0200000000010200 0000000000000000 0000000100000001 ffff8881da002500 raw: 0000000000000000 00000000000c000c 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff8881cf591900: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8881cf591980: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb > ffff8881cf591a00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ^ ffff8881cf591a80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8881cf591b00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ================================================================== In order to avoid opening a disconnected device, we need to check exist again after acquiring the existance lock, and bail out if necessary. Reported-by:
-
Oliver Neukum authored
commit 01ec0a5f upstream. The ioctl handler uses the intfdata of a second interface, which may not be present in a broken or malicious device, hence the intfdata needs to be checked for NULL. [jkosina@suse.cz: fix newly added spurious space] Reported-by: syzbot+965152643a75a56737be@syzkaller.appspotmail.com Signed-off-by:
-
Hui Wang authored
commit 401714d9 upstream. We have 3 new lenovo laptops which have conexant codec 0x14f11f86, these 3 laptops also have the noise issue when rebooting, after letting the codec enter D3 before rebooting or poweroff, the noise disappers. Instead of adding a new ID again in the reboot_notify(), let us make this function apply to all conexant codec. In theory make codec enter D3 before rebooting or poweroff is harmless, and I tested this change on a couple of other Lenovo laptops which have different conexant codecs, there is no side effect so far. Cc: stable@vger.kernel.org Signed-off-by:
Hui Wang <hui.wang@canonical.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Hui Wang authored
commit 871b9066 upstream. Make codec enter D3 before rebooting or poweroff can fix the noise issue on some laptops. And in theory it is harmless for all codecs to enter D3 before rebooting or poweroff, let us add a generic reboot_notify, then realtek and conexant drivers can call this function. Cc: stable@vger.kernel.org Signed-off-by:
-
Wenwen Wang authored
commit cfef67f0 upstream. In snd_hda_parse_generic_codec(), 'spec' is allocated through kzalloc(). Then, the pin widgets in 'codec' are parsed. However, if the parsing process fails, 'spec' is not deallocated, leading to a memory leak. To fix the above issue, free 'spec' before returning the error. Fixes: 352f7f91 ("ALSA: hda - Merge Realtek parser code to generic parser") Signed-off-by:
Wenwen Wang <wenwen@cs.uga.edu> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Takashi Iwai authored
commit de768ce4 upstream. MSI MPG X570 board is with another AMD HD-audio controller (PCI ID 1022:1487) and it requires the same workaround applied for X370, etc (PCI ID 1022:1457). BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=195303 Cc: <stable@vger.kernel.org> Signed-off-by:
-
Hui Peng authored
commit daac0715 upstream. The `uac_mixer_unit_descriptor` shown as below is read from the device side. In `parse_audio_mixer_unit`, `baSourceID` field is accessed from index 0 to `bNrInPins` - 1, the current implementation assumes that descriptor is always valid (the length of descriptor is no shorter than 5 + `bNrInPins`). If a descriptor read from the device side is invalid, it may trigger out-of-bound memory access. ``` struct uac_mixer_unit_descriptor { __u8 bLength; __u8 bDescriptorType; __u8 bDescriptorSubtype; __u8 bUnitID; __u8 bNrInPins; __u8 baSourceID[]; } ``` This patch fixes the bug by add a sanity check on the length of the descriptor. Reported-by:
Hui Peng <benquike@gmail.com> Reported-by:
Mathias Payer <mathias.payer@nebelwelt.net> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Hui Peng authored
commit 19bce474 upstream. `check_input_term` recursively calls itself with input from device side (e.g., uac_input_terminal_descriptor.bCSourceID) as argument (id). In `check_input_term`, if `check_input_term` is called with the same `id` argument as the caller, it triggers endless recursive call, resulting kernel space stack overflow. This patch fixes the bug by adding a bitmap to `struct mixer_build` to keep track of the checked ids and stop the execution if some id has been checked (similar to how parse_audio_unit handles unitid argument). Reported-by:
-
Takashi Iwai authored
commit 190d0381 upstream. HP Envy x360 (AMD Ryzen-based model) with 103c:8497 needs the same quirk like HP Spectre x360 for enabling the mute LED over Mic3 pin. BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=204373 Cc: <stable@vger.kernel.org> Signed-off-by:
-
Max Filippov authored
commit cd8869f4 upstream. ITLB entry modifications must be followed by the isync instruction before the new entries are possibly used. cpu_reset lacks one isync between ITLB way 6 initialization and jump to the identity mapping. Add missing isync to xtensa cpu_reset. Cc: stable@vger.kernel.org Signed-off-by:
Max Filippov <jcmvbkbc@gmail.com> Signed-off-by:
-
Viresh Kumar authored
commit 600f5bad upstream. To avoid reducing the frequency of a CPU prematurely, we skip reducing the frequency if the CPU had been busy recently. This should not be done when the limits of the policy are changed, for example due to thermal throttling. We should always get the frequency within the new limits as soon as possible. Trying to fix this by using only one flag, i.e. need_freq_update, can lead to a race condition where the flag gets cleared without forcing us to change the frequency at least once. And so this patch introduces another flag to avoid that race condition. Fixes: ecd28842 ("cpufreq: schedutil: Don't set next_freq to UINT_MAX") Cc: v4.18+ <stable@vger.kernel.org> # v4.18+ Reported-by:
Doug Smythies <dsmythies@telus.net> Tested-by:
Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Fabrice Gasnier authored
commit c289d662 upstream. This reverts commit 7e5d1fd7 ("pwm: Set class for exported channels in sysfs") as it causes regression with multiple pwm chip[1], when exporting a pwm channel (echo X > export): - ABI (Documentation/ABI/testing/sysfs-class-pwm) states pwmX should be created in /sys/class/pwm/pwmchipN/pwmX - Reverted patch causes new entry to be also created directly in /sys/class/pwm/pwmX - 1st time, exporting pwmX will create an entry in /sys/class/pwm/pwmX - class attributes are added under pwmX folder, such as export, unexport npwm, symlinks. This is wrong as it belongs to pwmchipN. It may cause bad behavior and report wrong values. - when another export happens on another pwmchip, it can't be created (e.g. -EEXIST). This is causing the issue with multiple pwmchip. Example on stm32 (stm32429i-eval) platform: $ ls /sys/class/pwm pwmchip0 pwmchip4 $ cd /sys/class/pwm/pwmchip0/ $ echo 0 > export $ ls /sys/class/pwm pwm0 pwmchip0 pwmchip4 $ cd /sys/class/pwm/pwmchip4/ $ echo 0 > export sysfs: cannot create duplicate filename '/class/pwm/pwm0' ...Exception stack follows... This is also seen on other platform [2] [1] https://lkml.org/lkml/2018/9/25/713 [2] https://lkml.org/lkml/2018/9/25/447Signed-off-by:
Fabrice Gasnier <fabrice.gasnier@st.com> Tested-by:
Gottfried Haider <gottfried.haider@gmail.com> Tested-by:
Michal Vokáč <michal.vokac@ysoft.com> Signed-off-by:
Thierry Reding <thierry.reding@gmail.com> Cc: John Keeping <john@metanate.com> Signed-off-by:
-
Isaac J. Manjarres authored
commit 95153169 upstream. Currently, when checking to see if accessing n bytes starting at address "ptr" will cause a wraparound in the memory addresses, the check in check_bogus_address() adds an extra byte, which is incorrect, as the range of addresses that will be accessed is [ptr, ptr + (n - 1)]. This can lead to incorrectly detecting a wraparound in the memory address, when trying to read 4 KB from memory that is mapped to the the last possible page in the virtual address space, when in fact, accessing that range of memory would not cause a wraparound to occur. Use the memory range that will actually be accessed when considering if accessing a certain amount of bytes will cause the memory address to wrap around. Link: http://lkml.kernel.org/r/1564509253-23287-1-git-send-email-isaacm@codeaurora.org Fixes: f5509cc1 ("mm: Hardened usercopy") Signed-off-by:
Prasad Sodagudi <psodagud@codeaurora.org> Signed-off-by:
Isaac J. Manjarres <isaacm@codeaurora.org> Co-developed-by:
William Kucharski <william.kucharski@oracle.com> Acked-by:
Kees Cook <keescook@chromium.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Trilok Soni <tsoni@codeaurora.org> Cc: <stable@vger.kernel.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Miles Chen authored
commit 54a83d6b upstream. This patch is sent to report an use after free in mem_cgroup_iter() after merging commit be265775 ("mm: memcg: fix use after free in mem_cgroup_iter()"). I work with android kernel tree (4.9 & 4.14), and commit be265775 ("mm: memcg: fix use after free in mem_cgroup_iter()") has been merged to the trees. However, I can still observe use after free issues addressed in the commit be265775. (on low-end devices, a few times this month) backtrace: css_tryget <- crash here mem_cgroup_iter shrink_node shrink_zones do_try_to_free_pages try_to_free_pages __perform_reclaim __alloc_pages_direct_reclaim __alloc_pages_slowpath __alloc_pages_nodemask To debug, I poisoned mem_cgroup before freeing it: static void __mem_cgroup_free(struct mem_cgroup *memcg) for_each_node(node) free_mem_cgroup_per_node_info(memcg, node); free_percpu(memcg->stat); + /* poison memcg before freeing it */ + memset(memcg, 0x78, sizeof(struct mem_cgroup)); kfree(memcg); } The coredump shows the position=0xdbbc2a00 is freed. (gdb) p/x ((struct mem_cgroup_per_node *)0xe5009e00)->iter[8] $13 = {position = 0xdbbc2a00, generation = 0x2efd} 0xdbbc2a00: 0xdbbc2e00 0x00000000 0xdbbc2800 0x00000100 0xdbbc2a10: 0x00000200 0x78787878 0x00026218 0x00000000 0xdbbc2a20: 0xdcad6000 0x00000001 0x78787800 0x00000000 0xdbbc2a30: 0x78780000 0x00000000 0x0068fb84 0x78787878 0xdbbc2a40: 0x78787878 0x78787878 0x78787878 0xe3fa5cc0 0xdbbc2a50: 0x78787878 0x78787878 0x00000000 0x00000000 0xdbbc2a60: 0x00000000 0x00000000 0x00000000 0x00000000 0xdbbc2a70: 0x00000000 0x00000000 0x00000000 0x00000000 0xdbbc2a80: 0x00000000 0x00000000 0x00000000 0x00000000 0xdbbc2a90: 0x00000001 0x00000000 0x00000000 0x00100000 0xdbbc2aa0: 0x00000001 0xdbbc2ac8 0x00000000 0x00000000 0xdbbc2ab0: 0x00000000 0x00000000 0x00000000 0x00000000 0xdbbc2ac0: 0x00000000 0x00000000 0xe5b02618 0x00001000 0xdbbc2ad0: 0x00000000 0x78787878 0x78787878 0x78787878 0xdbbc2ae0: 0x78787878 0x78787878 0x78787878 0x78787878 0xdbbc2af0: 0x78787878 0x78787878 0x78787878 0x78787878 0xdbbc2b00: 0x78787878 0x78787878 0x78787878 0x78787878 0xdbbc2b10: 0x78787878 0x78787878 0x78787878 0x78787878 0xdbbc2b20: 0x78787878 0x78787878 0x78787878 0x78787878 0xdbbc2b30: 0x78787878 0x78787878 0x78787878 0x78787878 0xdbbc2b40: 0x78787878 0x78787878 0x78787878 0x78787878 0xdbbc2b50: 0x78787878 0x78787878 0x78787878 0x78787878 0xdbbc2b60: 0x78787878 0x78787878 0x78787878 0x78787878 0xdbbc2b70: 0x78787878 0x78787878 0x78787878 0x78787878 0xdbbc2b80: 0x78787878 0x78787878 0x00000000 0x78787878 0xdbbc2b90: 0x78787878 0x78787878 0x78787878 0x78787878 0xdbbc2ba0: 0x78787878 0x78787878 0x78787878 0x78787878 In the reclaim path, try_to_free_pages() does not setup sc.target_mem_cgroup and sc is passed to do_try_to_free_pages(), ..., shrink_node(). In mem_cgroup_iter(), root is set to root_mem_cgroup because sc->target_mem_cgroup is NULL. It is possible to assign a memcg to root_mem_cgroup.nodeinfo.iter in mem_cgroup_iter(). try_to_free_pages struct scan_control sc = {...}, target_mem_cgroup is 0x0; do_try_to_free_pages shrink_zones shrink_node mem_cgroup *root = sc->target_mem_cgroup; memcg = mem_cgroup_iter(root, NULL, &reclaim); mem_cgroup_iter() if (!root) root = root_mem_cgroup; ... css = css_next_descendant_pre(css, &root->css); memcg = mem_cgroup_from_css(css); cmpxchg(&iter->position, pos, memcg); My device uses memcg non-hierarchical mode. When we release a memcg: invalidate_reclaim_iterators() reaches only dead_memcg and its parents. If non-hierarchical mode is used, invalidate_reclaim_iterators() never reaches root_mem_cgroup. static void invalidate_reclaim_iterators(struct mem_cgroup *dead_memcg) { struct mem_cgroup *memcg = dead_memcg; for (; memcg; memcg = parent_mem_cgroup(memcg) ... } So the use after free scenario looks like: CPU1 CPU2 try_to_free_pages do_try_to_free_pages shrink_zones shrink_node mem_cgroup_iter() if (!root) root = root_mem_cgroup; ... css = css_next_descendant_pre(css, &root->css); memcg = mem_cgroup_from_css(css); cmpxchg(&iter->position, pos, memcg); invalidate_reclaim_iterators(memcg); ... __mem_cgroup_free() kfree(memcg); try_to_free_pages do_try_to_free_pages shrink_zones shrink_node mem_cgroup_iter() if (!root) root = root_mem_cgroup; ... mz = mem_cgroup_nodeinfo(root, reclaim->pgdat->node_id); iter = &mz->iter[reclaim->priority]; pos = READ_ONCE(iter->position); css_tryget(&pos->css) <- use after free To avoid this, we should also invalidate root_mem_cgroup.nodeinfo.iter in invalidate_reclaim_iterators(). [cai@lca.pw: fix -Wparentheses compilation warning] Link: http://lkml.kernel.org/r/1564580753-17531-1-git-send-email-cai@lca.pw Link: http://lkml.kernel.org/r/20190730015729.4406-1-miles.chen@mediatek.com Fixes: 5ac8fb31 ("mm: memcontrol: convert reclaim iterator to simple css refcounting") Signed-off-by:
Miles Chen <miles.chen@mediatek.com> Signed-off-by:
Qian Cai <cai@lca.pw> Acked-by:
Michal Hocko <mhocko@suse.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Yang Shi authored
commit a53190a4 upstream. When running syzkaller internally, we ran into the below bug on 4.9.x kernel: kernel BUG at mm/huge_memory.c:2124! invalid opcode: 0000 [#1] SMP KASAN CPU: 0 PID: 1518 Comm: syz-executor107 Not tainted 4.9.168+ #2 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 0.5.1 01/01/2011 task: ffff880067b34900 task.stack: ffff880068998000 RIP: split_huge_page_to_list+0x8fb/0x1030 mm/huge_memory.c:2124 Call Trace: split_huge_page include/linux/huge_mm.h:100 [inline] queue_pages_pte_range+0x7e1/0x1480 mm/mempolicy.c:538 walk_pmd_range mm/pagewalk.c:50 [inline] walk_pud_range mm/pagewalk.c:90 [inline] walk_pgd_range mm/pagewalk.c:116 [inline] __walk_page_range+0x44a/0xdb0 mm/pagewalk.c:208 walk_page_range+0x154/0x370 mm/pagewalk.c:285 queue_pages_range+0x115/0x150 mm/mempolicy.c:694 do_mbind mm/mempolicy.c:1241 [inline] SYSC_mbind+0x3c3/0x1030 mm/mempolicy.c:1370 SyS_mbind+0x46/0x60 mm/mempolicy.c:1352 do_syscall_64+0x1d2/0x600 arch/x86/entry/common.c:282 entry_SYSCALL_64_after_swapgs+0x5d/0xdb Code: c7 80 1c 02 00 e8 26 0a 76 01 <0f> 0b 48 c7 c7 40 46 45 84 e8 4c RIP [<ffffffff81895d6b>] split_huge_page_to_list+0x8fb/0x1030 mm/huge_memory.c:2124 RSP <ffff88006899f980> with the below test: uint64_t r[1] = {0xffffffffffffffff}; int main(void) { syscall(__NR_mmap, 0x20000000, 0x1000000, 3, 0x32, -1, 0); intptr_t res = 0; res = syscall(__NR_socket, 0x11, 3, 0x300); if (res != -1) r[0] = res; *(uint32_t*)0x20000040 = 0x10000; *(uint32_t*)0x20000044 = 1; *(uint32_t*)0x20000048 = 0xc520; *(uint32_t*)0x2000004c = 1; syscall(__NR_setsockopt, r[0], 0x107, 0xd, 0x20000040, 0x10); syscall(__NR_mmap, 0x20fed000, 0x10000, 0, 0x8811, r[0], 0); *(uint64_t*)0x20000340 = 2; syscall(__NR_mbind, 0x20ff9000, 0x4000, 0x4002, 0x20000340, 0x45d4, 3); return 0; } Actually the test does: mmap(0x20000000, 16777216, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_ANONYMOUS, -1, 0) = 0x20000000 socket(AF_PACKET, SOCK_RAW, 768) = 3 setsockopt(3, SOL_PACKET, PACKET_TX_RING, {block_size=65536, block_nr=1, frame_size=50464, frame_nr=1}, 16) = 0 mmap(0x20fed000, 65536, PROT_NONE, MAP_SHARED|MAP_FIXED|MAP_POPULATE|MAP_DENYWRITE, 3, 0) = 0x20fed000 mbind(..., MPOL_MF_STRICT|MPOL_MF_MOVE) = 0 The setsockopt() would allocate compound pages (16 pages in this test) for packet tx ring, then the mmap() would call packet_mmap() to map the pages into the user address space specified by the mmap() call. When calling mbind(), it would scan the vma to queue the pages for migration to the new node. It would split any huge page since 4.9 doesn't support THP migration, however, the packet tx ring compound pages are not THP and even not movable. So, the above bug is triggered. However, the later kernel is not hit by this issue due to commit d44d363f ("mm: don't assume anonymous pages have SwapBacked flag"), which just removes the PageSwapBacked check for a different reason. But, there is a deeper issue. According to the semantic of mbind(), it should return -EIO if MPOL_MF_MOVE or MPOL_MF_MOVE_ALL was specified and MPOL_MF_STRICT was also specified, but the kernel was unable to move all existing pages in the range. The tx ring of the packet socket is definitely not movable, however, mbind() returns success for this case. Although the most socket file associates with non-movable pages, but XDP may have movable pages from gup. So, it sounds not fine to just check the underlying file type of vma in vma_migratable(). Change migrate_page_add() to check if the page is movable or not, if it is unmovable, just return -EIO. But do not abort pte walk immediately, since there may be pages off LRU temporarily. We should migrate other pages if MPOL_MF_MOVE* is specified. Set has_unmovable flag if some paged could not be not moved, then return -EIO for mbind() eventually. With this change the above test would return -EIO as expected. [yang.shi@linux.alibaba.com: fix review comments from Vlastimil] Link: http://lkml.kernel.org/r/1563556862-54056-3-git-send-email-yang.shi@linux.alibaba.com Link: http://lkml.kernel.org/r/1561162809-59140-3-git-send-email-yang.shi@linux.alibaba.comSigned-off-by:
Yang Shi <yang.shi@linux.alibaba.com> Reviewed-by:
Vlastimil Babka <vbabka@suse.cz> Cc: Michal Hocko <mhocko@suse.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Yang Shi authored
commit d8835445 upstream. When both MPOL_MF_MOVE* and MPOL_MF_STRICT was specified, mbind() should try best to migrate misplaced pages, if some of the pages could not be migrated, then return -EIO. There are three different sub-cases: 1. vma is not migratable 2. vma is migratable, but there are unmovable pages 3. vma is migratable, pages are movable, but migrate_pages() fails If #1 happens, kernel would just abort immediately, then return -EIO, after a7f40cfe ("mm: mempolicy: make mbind() return -EIO when MPOL_MF_STRICT is specified"). If #3 happens, kernel would set policy and migrate pages with best-effort, but won't rollback the migrated pages and reset the policy back. Before that commit, they behaves in the same way. It'd better to keep their behavior consistent. But, rolling back the migrated pages and resetting the policy back sounds not feasible, so just make #1 behave as same as #3. Userspace will know that not everything was successfully migrated (via -EIO), and can take whatever steps it deems necessary - attempt rollback, determine which exact page(s) are violating the policy, etc. Make queue_pages_range() return 1 to indicate there are unmovable pages or vma is not migratable. The #2 is not handled correctly in the current kernel, the following patch will fix it. [yang.shi@linux.alibaba.com: fix review comments from Vlastimil] Link: http://lkml.kernel.org/r/1563556862-54056-2-git-send-email-yang.shi@linux.alibaba.com Link: http://lkml.kernel.org/r/1561162809-59140-2-git-send-email-yang.shi@linux.alibaba.comSigned-off-by:
-
Ralph Campbell authored
commit 1de13ee5 upstream. When migrating an anonymous private page to a ZONE_DEVICE private page, the source page->mapping and page->index fields are copied to the destination ZONE_DEVICE struct page and the page_mapcount() is increased. This is so rmap_walk() can be used to unmap and migrate the page back to system memory. However, try_to_unmap_one() computes the subpage pointer from a swap pte which computes an invalid page pointer and a kernel panic results such as: BUG: unable to handle page fault for address: ffffea1fffffffc8 Currently, only single pages can be migrated to device private memory so no subpage computation is needed and it can be set to "page". [rcampbell@nvidia.com: add comment] Link: http://lkml.kernel.org/r/20190724232700.23327-4-rcampbell@nvidia.com Link: http://lkml.kernel.org/r/20190719192955.30462-4-rcampbell@nvidia.com Fixes: a5430dda ("mm/migrate: support un-addressable ZONE_DEVICE page in migration") Signed-off-by:
Ralph Campbell <rcampbell@nvidia.com> Cc: "Jérôme Glisse" <jglisse@redhat.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Jason Gunthorpe <jgg@mellanox.com> Cc: John Hubbard <jhubbard@nvidia.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Christoph Lameter <cl@linux.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Ira Weiny <ira.weiny@intel.com> Cc: Jan Kara <jack@suse.cz> Cc: Lai Jiangshan <jiangshanlai@gmail.com> Cc: Logan Gunthorpe <logang@deltatee.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Michal Hocko <mhocko@suse.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: <stable@vger.kernel.org> Signed-off-by:
-
NeilBrown authored
commit 6a2aeab5 upstream. If you use lseek or similar (e.g. pread) to access a location in a seq_file file that is within a record, rather than at a record boundary, then the first read will return the remainder of the record, and the second read will return the whole of that same record (instead of the next record). When seeking to a record boundary, the next record is correctly returned. This bug was introduced by a recent patch (identified below). Before that patch, seq_read() would increment m->index when the last of the buffer was returned (m->count == 0). After that patch, we rely on ->next to increment m->index after filling the buffer - but there was one place where that didn't happen. Link: https://lkml.kernel.org/lkml/877e7xl029.fsf@notabene.neil.brown.name/ Fixes: 1f4aace6 ("fs/seq_file.c: simplify seq_file iteration code and interface") Signed-off-by:
NeilBrown <neilb@suse.com> Reported-by:
Sergei Turchanov <turchanov@farpost.com> Tested-by:
-
Gustavo A. R. Silva authored
commit 1ee1119d upstream. Add missing break statement in order to prevent the code from falling through to case SH_BREAKPOINT_WRITE. Fixes: 09a07294 ("sh: hw-breakpoints: Add preliminary support for SH-4A UBC.") Cc: stable@vger.kernel.org Reviewed-by:
Guenter Roeck <linux@roeck-us.net> Tested-by:
Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by:
-
- 16 Aug, 2019 11 commits
-
-
Greg Kroah-Hartman authored
-
Luca Coelho authored
commit f5a47fae upstream. We erroneously added a check for FW API version 41 before sending GEO_TX_POWER_LIMIT, but this was already implemented in version 38. Additionally, it was cherry-picked to older versions, namely 17, 26 and 29, so check for those as well. Cc: stable@vger.kernel.org Fixes: eca1e56c ("iwlwifi: mvm: don't send GEO_TX_POWER_LIMIT to old firmwares") Signed-off-by:
Luca Coelho <luciano.coelho@intel.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Luca Coelho authored
commit 39bd984c upstream. Firmware versions before 41 don't support the GEO_TX_POWER_LIMIT command, and sending it to the firmware will cause a firmware crash. We allow this via debugfs, so we need to return an error value in case it's not supported. This had already been fixed during init, when we send the command if the ACPI WGDS table is present. Fix it also for the other, userspace-triggered case. Cc: stable@vger.kernel.org Fixes: 7fe90e0e ("iwlwifi: mvm: refactor geo init") Signed-off-by:
-
Emmanuel Grumbach authored
commit ba3224db upstream. The index for the elements of the ACPI object we dereference was static. This means that if we called the function twice we wouldn't start from 3 again, but rather from the latest index we reached in the previous call. This was dutifully reported by KASAN. Fix this. Cc: stable@vger.kernel.org Fixes: 69964905 ("iwlwifi: mvm: add support for EWRD (Dynamic SAR) ACPI table") Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
Emmanuel Grumbach authored
commit 87e7e25a upstream. In order to remember how to unmap a memory (as single or as page), we maintain a bit per Transmit Buffer (TBs) in the meta data (structure iwl_cmd_meta). We maintain a bitmap: 1 bit per TB. If the TB is set, we will free the memory as a page. This bitmap was never cleared. Fix this. Cc: stable@vger.kernel.org Fixes: 3cd1980b ("iwlwifi: pcie: introduce new tfd and tb formats") Signed-off-by:
-
Brian Norris authored
commit df612421 upstream. Commit 63d7ef36 ("mwifiex: Don't abort on small, spec-compliant vendor IEs") adjusted the ieee_types_vendor_header struct, which inadvertently messed up the offsets used in mwifiex_is_wpa_oui_present(). Add that offset back in, mirroring mwifiex_is_rsn_oui_present(). As it stands, commit 63d7ef36 breaks compatibility with WPA (not WPA2) 802.11n networks, since we hit the "info: Disable 11n if AES is not supported by AP" case in mwifiex_is_network_compatible(). Fixes: 63d7ef36 ("mwifiex: Don't abort on small, spec-compliant vendor IEs") Cc: <stable@vger.kernel.org> Signed-off-by:
Brian Norris <briannorris@chromium.org> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Wanpeng Li authored
commit 17e433b5 upstream. After commit d73eb57b (KVM: Boost vCPUs that are delivering interrupts), a five years old bug is exposed. Running ebizzy benchmark in three 80 vCPUs VMs on one 80 pCPUs Skylake server, a lot of rcu_sched stall warning splatting in the VMs after stress testing: INFO: rcu_sched detected stalls on CPUs/tasks: { 4 41 57 62 77} (detected by 15, t=60004 jiffies, g=899, c=898, q=15073) Call Trace: flush_tlb_mm_range+0x68/0x140 tlb_flush_mmu.part.75+0x37/0xe0 tlb_finish_mmu+0x55/0x60 zap_page_range+0x142/0x190 SyS_madvise+0x3cd/0x9c0 system_call_fastpath+0x1c/0x21 swait_active() sustains to be true before finish_swait() is called in kvm_vcpu_block(), voluntarily preempted vCPUs are taken into account by kvm_vcpu_on_spin() loop greatly increases the probability condition kvm_arch_vcpu_runnable(vcpu) is checked and can be true, when APICv is enabled the yield-candidate vCPU's VMCS RVI field leaks(by vmx_sync_pir_to_irr()) into spinning-on-a-taken-lock vCPU's current VMCS. This patch fixes it by checking conservatively a subset of events. Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Marc Zyngier <Marc.Zyngier@arm.com> Cc: stable@vger.kernel.org Fixes: 98f4a146 (KVM: add kvm_arch_vcpu_runnable() test to kvm_vcpu_on_spin() loop) Signed-off-by:
Wanpeng Li <wanpengli@tencent.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Trond Myklebust authored
commit 09a54f0e upstream. If the user specifies an open mode of 3, then we don't have a NFSv4 state attached to the context, and so we Oops when we try to dereference it. Reported-by:
Olga Kornievskaia <aglo@umich.edu> Fixes: 29b59f94 ("NFSv4: change nfs4_do_setattr to take...") Signed-off-by:
Trond Myklebust <trond.myklebust@hammerspace.com> Cc: stable@vger.kernel.org # v4.10: 991eedb1: NFSv4: Only pass the... Cc: stable@vger.kernel.org # v4.10+ Signed-off-by:
-
Steve French authored
commit 8d33096a upstream. We had a report of a server which did not do a DFS referral because the session setup Capabilities field was set to 0 (unlike negotiate protocol where we set CAP_DFS). Better to send it session setup in the capabilities as well (this also more closely matches Windows client behavior). Signed-off-by:
Steve French <stfrench@microsoft.com> Reviewed-off-by:
Ronnie Sahlberg <lsahlber@redhat.com> Reviewed-by:
Pavel Shilovsky <pshilov@microsoft.com> CC: Stable <stable@vger.kernel.org> Signed-off-by:
-
Pavel Shilovsky authored
commit e99c63e4 upstream. Currently we skip SMB2_TREE_CONNECT command when checking during reconnect because Tree Connect happens when establishing an SMB session. For SMB 3.0 protocol version the code also calls validate negotiate which results in SMB2_IOCL command being sent over the wire. This may deadlock on trying to acquire a mutex when checking for reconnect. Fix this by skipping SMB2_IOCL command when doing the reconnect check. Signed-off-by:
-
Vivek Goyal authored
commit d75996dd upstream. Vivek: "As of now dax_layout_busy_page() calls unmap_mapping_range() with last argument as 1, which says even unmap cow pages. I am wondering who needs to get rid of cow pages as well. I noticed one interesting side affect of this. I mount xfs with -o dax and mmaped a file with MAP_PRIVATE and wrote some data to a page which created cow page. Then I called fallocate() on that file to zero a page of file. fallocate() called dax_layout_busy_page() which unmapped cow pages as well and then I tried to read back the data I wrote and what I get is old data from persistent memory. I lost the data I had written. This read basically resulted in new fault and read back the data from persistent memory. This sounds wrong. Are there any users which need to unmap cow pages as well? If not, I am proposing changing it to not unmap cow pages. I noticed this while while writing virtio_fs code where when I tried to reclaim a memory range and that corrupted the executable and I was running from virtio-fs and program got segment violation." Dan: "In fact the unmap_mapping_range() in this path is only to synchronize against get_user_pages_fast() and force it to call back into the filesystem to re-establish the mapping. COW pages should be left untouched by dax_layout_busy_page()." Cc: <stable@vger.kernel.org> Fixes: 5fac7408 ("mm, fs, dax: handle layout changes to pinned dax mappings") Signed-off-by:
Vivek Goyal <vgoyal@redhat.com> Link: https://lore.kernel.org/r/20190802192956.GA3032@redhat.comSigned-off-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
-
