In preparation for adding HTC pipe implementation add htc-ops.h to make
it possible dynamically choose which HTC type is used.

Needed for full USB support.

Based on the code by Ray Chen <raychen@qca.qualcomm.com>.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Ray Chen <raychen@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Void pointers are bad.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Needed when using USB.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Needed by the USB code.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

It's also needed by the USB code.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This is needed by the USB code. Also while at it replace one void pointer
with a properly typed pointer.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Ram reserved size is not needed with ar6004.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Configure the inactivity timeout passed in start_ap() to
firmware. This capability is advertised only when fw supports
it, there is a new bit (ATH6KL_FW_CAPABILITY_INACTIVITY_TIMEOUT)
in firmware capability ie for driver to learn fw's capability.
After the fw finds out the station is inactive, it will probe
the station with null func frames. By default, the timeout is
10 secs.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Adding below steps helps to get good power numbers
in deep sleep suspend path,

    * Disable WOW mode.
    * Flush data packets and wait for all control packets.
      to be cleared in TX path before deep sleep suspend.
    * Set host sleep mode to SLEEP.

Below steps are added to perform the recovery action
while the system resume from deep sleep,

     * Set host sleep mode to AWAKE.
     * Reset scan parameters to default value.

In addition, Debug prints are added to track deep sleep
suspend/resume state.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The piece of code used in ath6kk_wow_suspend function
to configure the host sleep mode is needed in deep sleep
case also.

Moving that portion to a separate function called
ath6kl_update_host_mode() would be helpful to avoid
the duplication of the same code in deep sleep path.

There is no functional change.

kvalo: move inline functions to cfg80211.c and fix a long line
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Dump htc header along with the warning message when the request
to Rx with invalid frame length is detected.

kvalo: fix open parenthesis alignment
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

If the device disconnects from an AP when it is in suspending state. You will
get the following message from wpa_supplicant after waking the device up and
sending scan request:

"Scan trigger failed: ret=-16 (Device or resource busy)"

Fix the issue by sending a scan complete event before starting scheduled
scan.

kvalo: cosmetic changes to commit log
Signed-off-by: Isaac.li <shonmou@gmail.com>
Tested-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Make sure printf formats and arguments match.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Firmware reports the below ARP offload related information
while sending the target statistic event to the host.

     * Number of ARP packets received.
     * Number of packets matched with the device IP addr.
     * Number of ARP response packet sent to the remote.

This patch adds the additional debug prints in debugfs
entry tgt_stats. It will be useful to know the ARP offload
execution status.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This is useful during debugging to check if disconnect commands were issued by
the host.
Signed-off-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

When the device is in P2P GO mode and in listen state, the correct behavior is
to see two different probe response frames - one from P2P device and the other
from GO. wpa_supplicant uses the same mechanism to send the frame in both cases
(ath6kl_mgmt_tx). For GO probe response, ath6kl needs to call
ath6kl_send_go_probe_resp (this will add only WSC/P2P IEs and the rest of the
IEs are filled in by the firmware). That was done based on the nw_type ==
AP_NETWORK which would work if P2P Device role were in a separate netdev. When
P2P Device and GO use the same netdev, ath6kl needs to use the special GO probe
response case only if SSID is longer than P2P wildcard SSID.
Signed-off-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Reviewed-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

libertas provides a dump_survey implementation based on reading of
a RSSI value. However, this RSSI value is calculated based on the
last received beacon from the associated AP - it is not a good
way of surveying a channel in general, and even causes an error
if the card is not associated to a network.

As this is not appropriate as a survey, remove it. This fixes an
issue where something in userspace is repeatedly calling site-survey
during boot, resulting in many repeated errors as the RSSI value cannot
be read before associating.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Makes them more readable and reduces code size
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Program tx gain through iniModesTxGain like on AR9287
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

use iniModesFastClock for 5 ghz fast clock specific settings, and
iniAdditional for clock/chip specific initval overrides
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Program the ah->ini_japan2484 INI values which were left out by accident
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

These arrays are unused
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The ATH9K_HW_CAP_AUTOSLEEP check is bogus, the rx status area needs to be
cleared on all non-EDMA PCI/AHB based chipsets anyway.
Limit the memset to the rx status area to improve performance.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The driver can just check the mask directly
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

By checking for NR_CPUS, the compiler can optimize out register access
serialization code on non-SMP kernels
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The default antenna (as programmed by the INI file) is always 0 anyway.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Automatically set the ah->htc_reset_init on init and after PHY disable.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

TXQ_FLAG_TXOKINT_ENABLE and TXQ_FLAG_TXERRINT_ENABLE are always set and
used together, and they share the same bitmask in enum ath9k_tx_queue_flags.
Simplify the code that tests for these flags.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

uapsd_queues and uapsd_max_sp_len are relevant only for managed
interfaces, and can be configured differently for each vif.

Move them from the local struct to sdata->u.mgd, and update
the debugfs functions accordingly.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some debugfs write functions call kstrto* functions, which
assume the string is null-terminated. Make it valid by changing
ieee80211_if_write() to use static buffer instead of allocating
one, and set the last char to NULL.

(The write functions try to parse some integer/mac address,
so 64 bytes buffer should be enough)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The current max throughput rate is known to be good as otherwise it
wouldn't be the max throughput rate. Since rate sampling can introduce
some overhead (by adding RTS for example or due to not aggregating the
frame) don't sample the max throughput rate.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

TX status fifo is limited to 16 elements. When we send more frames than
that, we can easily loose status, what is not good for rate scaling
algorithm.

On my testing the change does not degrade performance, actually make
is slightly better. Additionally with the patch I can see much less
various rt2x00 warnings in dmesg.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Tx statuses of aggregated subframes contain packetid of first subframe
in the AMPDU. We can not identify AMPDU subframes based on packedid, so
simply assume that status match first pending frame in the queue. Thats
mostly the same what 2800pci do.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently we read tx status register after each urb data transfer. As
callback procedure also trigger reading, that causing we have many
"threads" of reading status. To prevent that introduce TX_STATUS_READING
flags, and check if we are already in process of sequential reading
TX_STA_FIFO, before requesting new reads.

Change timer to hrtimer, that make TX_STA_FIFO overruns less possible.
Use 200 us for initial timeout, and then reschedule in 100 us period,
this values probably have to be tuned.

Make changes on txdone work. Schedule it from
rt2800usb_tx_sta_fifo_read_completed() callback when first valid status
show up. Check in callback if tx status timeout happens, and schedule
work on that condition too. That make possible to remove tx status
timeout from generic watchdog. I moved that to rt2800usb.

Loop in txdone work, that should prevent situation when we queue work,
which is already processed, and after finish work is not rescheduled
again.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Patch change txdone code to make it similar like txdone in rt2800pci,
process only one entry from queue matching tx status.

Before we processed all pending entries from queue until PACKEDID match,
that caused that we do not report tx statuses correctly.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>