Add a device tree for the 8MNANOD3L-EVK eval board which features an
IMX8MN SoC. It is similar to the 8MNANODLPD4-EVK eval board except it
has an IMX8MN UltraLite SoC and DDR3L memory. It esp. differs in the
PMIC configuration because the SoC has a smaller package and thus the
ARM core voltage is combined with the SoC voltage and the DDR voltage
is 1.35V for the DDR3L memory.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the missing 'uart-has-rtscts' property to UART's that have hardware
flow control capability.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the Video Processing Unit node for IMX8Q SoC.
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Shijie Qin <shijie.qin@nxp.com>
Signed-off-by: Zhou Peng <eagle.zhou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The SDHC controller in the imx8mp has the same controller
as the imx8mm which supports HS400-ES. Change the compatible
fallback to imx8mm to enable it, but keep the imx7d-usdhc
to prevent breaking backwards compatibility.
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The SDHC controller in the imx8mn has the same controller
as the imx8mm which supports HS400-ES. Change the compatible
fallback to imx8mm to enable it, but keep the imx7d-usdhc
to prevent breaking backwards compatibility.
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch adds the device tree to support Toradex Verdin iMX8M Plus [1]
a computer on module which can be used on different carrier boards.

The module consists of an NXP i.MX 8M Plus family SoC (either i.MX 8M
Plus Quad or 8M Plus QuadLite), a PCA9450C PMIC, a Gigabit Ethernet PHY,
1, 2, 4 or 8 GB of LPDDR4 RAM, an eMMC, a TLA2024 ADC, an I2C EEPROM, an
RX8130 RTC, an optional I2C temperature sensor plus an optional
Bluetooth/Wi-Fi module.

Anything that is not self-contained on the module is disabled by
default.

The device tree for the Dahlia includes the module's device tree and
enables the supported peripherals of the carrier board.

The device tree for the Verdin Development Board includes the module's
device tree as well as the Dahlia one as it is a superset and supports
almost all peripherals available.

So far there is no display functionality supported at all but basic
console UART, USB host, eMMC and Ethernet functionality work fine.

[1] https://www.toradex.com/computer-on-modules/verdin-arm-family/nxp-imx-8m-plusSigned-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add DMA properties to uart2 node.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The node names should be generic and SPI NOR dtschema expects "flash".
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

fsl,clk-source property is of type uint8 and need to be defined as
"/bits/ 8 <0>". Simply setting value to 0 raise warning:
can@2180000: fsl,clk-source:0: [0, 0, 0, 0] is too long
Signed-off-by: Kuldeep Singh <singh.kuldeep87k@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

At the moment, the dtsi will force the dr_mode to host. This is
problematic because it will always turn on the Vbus voltage regardless
if the port is host or device. This might lead to a "shortcut" between
the two USB endpoints because both might have their Vbus supplies
enabled. Therefore, the default should be "otg" for any ports which
aren't host only (from a SoC point of view) and have a user of the dtsi
file overwrite that explicitly.

Move the 'dr_mode = "host";' into the board dts. Now that the dtsi
doesn't set the dr_mode anymore, we can also drop the 'dr_mode = "otg";'
in the board dts because that is the default value if dr_mode is not
set.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Enable the ocelot-8021q tagger by default which supports ethernet flow
control.

The new default is set in the common board dtsi. The actual switch
node is enabled on a per board variant basis. Because of this we
set the new tagger default for both internal ports and a particular
variant is free to choose among the two port.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add SD1 sleep pinctrl to avoid backfeeding during sleep.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add a note about us using discrete external on-module resistors
pulling-up to the on-module +V3.3_1.8_SD (LDO5) rail and explicitly
disabling the internal pull-ups due to ERR050080 [1]:

IO: Degradation of internal IO pullup/pulldown current capability for
IO’s continuously driven in a 3.3V operating mode

[1] https://www.nxp.com/webapp/Download?colCode=IMX8MM_0N87WSigned-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Fix capitalisation of Verdin in comments.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Alphabetically re-order pinctrl groups.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Update IOMUX configuration as required by the hardware design team.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add a note about the bootloader being expected to switch on the I2C
level shifter for the TLA2024 ADC behind this PMIC.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Make sure we only have dashes rather than underscores in node names by
renaming ctrl_sleep_moci-hog to ctrl-sleep-moci-hog.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Alphabetically re-order nodes.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Fix multi-line comment style.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Annotate regulators which are on-module.
Rename usb_otg{1/2}_vbus to USB_{1/2}_EN more in-line with Verdin spec.
Annotate PMIC regulators with information on which BUCK/LDO they are on.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX8MP use synopsys V3.70a ddr controller IP, so add edac support
for i.MX8MP based on "snps,ddrc-3.80a" synopsys edac driver.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add A53 OPP table and cpu regulator to support cpu-freq driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anson Huang <Anson.Huang@nxp.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

And missing speed grade phandle to cpu@0 node.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anson Huang <Anson.Huang@nxp.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the DT nodes for both the 3D and 2D GPU cores found on the i.MX8MP.

etnaviv-gpu 38000000.gpu: model: GC7000, revision: 6204
etnaviv-gpu 38008000.gpu: model: GC520, revision: 5341
[drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Tested-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the power domains for the GPUs, which do not require any interaction with
a blk-ctrl, but are simply two PU domains nested inside a MIX domain.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

There is a 32MiB Micron MT25QU256ABA1 serial NOR flash on the EVK board.
Add a device tree node for it.

Tested on a 8MNANOD3L-EVK.
Signed-off-by: Michael Walle <michael@walle.cc>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The r4 ("Evergreen") hardware revision of the Librem 5 phone includes a
slightly different panel than the revisions before it. Since its'
description is available, describe it properly for the board.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This partition will hold a squashfs firmware jail. Only one read-only
partition is needed.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

1,5A is what's used by the type-c controller on the Librem 5 board so
increase ti,boost-max-current to 1,5A too.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

That pin is not connected on the board so no need to describe it.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

They turn on the display currently so to be consistent, let's make
them wake the system from suspend as well.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The i.MX8MQ PLL support hdmi phy 27m as pll reference clock,
so add a fixed clock for it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Use the proper voltages as supported by the board instead of the ones
supported by the PMIC. The voltages were taken from both the schematic
of the 8MNANOLPD4-EVK eval board and the datasheet of the IMX8MN SoC.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Use the power signal names as given in the schematics of the reference
board.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The node name of Ethernet controller should be "ethernet" instead of
"usbether" as required by Ethernet controller devicetree schema:
 Documentation/devicetree/bindings/net/ethernet-controller.yaml

This patch can potentially affect boot loaders patching against full
node path instead of using device aliases.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for Data Modul i.MX8M Mini eDM SBC board. This is an
evaluation board for various custom display units. Currently
supported are serial console, ethernet, eMMC, SD, PCIe, SPI NOR,
USB host and USB OTG.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

BSH SystemMaster (SMM) S2 PRO board comes with an audio card based on
tlv320aic31xx family codec.

The audio card exposes two playback devices, one of them using the EASRC
(Enhanced Asynchronous Sample Rate Converter) module. Note that this
would require SDMA and EASRC firmware in order to work.
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pull more tracing updates from Steven Rostedt:

 - Rename the staging files to give them some meaning. Just
   stage1,stag2,etc, does not show what they are for

 - Check for NULL from allocation in bootconfig

 - Hold event mutex for dyn_event call in user events

 - Mark user events to broken (to work on the API)

 - Remove eBPF updates from user events

 - Remove user events from uapi header to keep it from being installed.

 - Move ftrace_graph_is_dead() into inline as it is called from hot
   paths and also convert it into a static branch.

* tag 'trace-v5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Move user_events.h temporarily out of include/uapi
  ftrace: Make ftrace_graph_is_dead() a static branch
  tracing: Set user_events to BROKEN
  tracing/user_events: Remove eBPF interfaces
  tracing/user_events: Hold event_mutex during dyn_event_add
  proc: bootconfig: Add null pointer check
  tracing: Rename the staging files for trace_events