commit 5523d11c upstream.

We don't really need to use different mac colors when adding mac
contexts, because they're not used anywhere.  In fact, the firmware
doesn't accept 255 as a valid color, so we get into a SYSASSERT 0x3401
when we reach that.

Remove the color increment to use always zero and avoid reaching 255.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit fd66fc1c upstream.

When iwl_mvm_power_update_mac() is called, we have already added the
mac context, so if this call fails we should remove the mac.

Fixes: commit e5e7aa8e ('iwlwifi: mvm: refactor power code')
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2cee4762 upstream.

These are coming from the FW and are used to access arrays.
Bad values can cause an out of bounds access so discard
such ba_notifs and warn.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit cd8f4384 upstream.

The base address of the scheduler in the device's memory
(SRAM) comes from two different sources. The periphery
register and the alive notification from the firmware.
We have a check in iwl_pcie_tx_start that ensures that
they are the same.
When we resume from WoWLAN, the firmware may have crashed
for whatever reason. In that case, the whole device may be
reset which means that the periphery register will hold a
meaningless value. When we come to compare
trans_pcie->scd_base_addr (which really holds the value we
had when we loaded the WoWLAN firmware upon suspend) and
the current value of the register, we don't see a match
unsurprisingly.
Trick the check to avoid a loud yet harmless WARN.
Note that when the WoWLAN has crashed, we will see that
in iwl_trans_pcie_d3_resume which will let the op_mode
know. Once the op_mode is informed that the WowLAN firmware
has crashed, it can't do much besides resetting the whole
device.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6ee8e25f upstream.

Commit e9fd702a ("audit: convert audit watches to use fsnotify
instead of inotify") broke handling of renames in audit.  Audit code
wants to update inode number of an inode corresponding to watched name
in a directory.  When something gets renamed into a directory to a
watched name, inotify previously passed moved inode to audit code
however new fsnotify code passes directory inode where the change
happened.  That confuses audit and it starts watching parent directory
instead of a file in a directory.

This can be observed for example by doing:

  cd /tmp
  touch foo bar
  auditctl -w /tmp/foo
  touch foo
  mv bar foo
  touch foo

In audit log we see events like:

  type=CONFIG_CHANGE msg=audit(1423563584.155:90): auid=1000 ses=2 op="updated rules" path="/tmp/foo" key=(null) list=4 res=1
  ...
  type=PATH msg=audit(1423563584.155:91): item=2 name="bar" inode=1046884 dev=08:0 2 mode=0100644 ouid=0 ogid=0 rdev=00:00 nametype=DELETE
  type=PATH msg=audit(1423563584.155:91): item=3 name="foo" inode=1046842 dev=08:0 2 mode=0100644 ouid=0 ogid=0 rdev=00:00 nametype=DELETE
  type=PATH msg=audit(1423563584.155:91): item=4 name="foo" inode=1046884 dev=08:0 2 mode=0100644 ouid=0 ogid=0 rdev=00:00 nametype=CREATE
  ...

and that's it - we see event for the first touch after creating the
audit rule, we see events for rename but we don't see any event for the
last touch.  However we start seeing events for unrelated stuff
happening in /tmp.

Fix the problem by passing moved inode as data in the FS_MOVED_FROM and
FS_MOVED_TO events instead of the directory where the change happens.
This doesn't introduce any new problems because noone besides
audit_watch.c cares about the passed value:

  fs/notify/fanotify/fanotify.c cares only about FSNOTIFY_EVENT_PATH events.
  fs/notify/dnotify/dnotify.c doesn't care about passed 'data' value at all.
  fs/notify/inotify/inotify_fsnotify.c uses 'data' only for FSNOTIFY_EVENT_PATH.
  kernel/audit_tree.c doesn't care about passed 'data' at all.
  kernel/audit_watch.c expects moved inode as 'data'.

Fixes: e9fd702a ("audit: convert audit watches to use fsnotify instead of inotify")
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Paul Moore <paul@paul-moore.com>
Cc: Eric Paris <eparis@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3443a3bc upstream.

When the superblock is modified in a transaction, the commonly
modified fields are not actually copied to the superblock buffer to
avoid the buffer lock becoming a serialisation point. However, there
are some other operations that modify the superblock fields within
the transaction that don't directly log to the superblock but rely
on the changes to be applied during the transaction commit (to
minimise the buffer lock hold time).

When we do this, we fail to mark the buffer log item as being a
superblock buffer and that can lead to the buffer not being marked
with the corect type in the log and hence causing recovery issues.
Fix it by setting the type correctly, similar to xfs_mod_sb()...
Tested-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit fe22d552 upstream.

Conversion from local to extent format does not set the buffer type
correctly on the new extent buffer when a symlink data is moved out
of line.

Fix the symlink code and leave a comment in the generic bmap code
reminding us that the format-specific data copy needs to set the
destination buffer type appropriately.
Tested-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f19b872b upstream.

This leads to log recovery throwing errors like:

XFS (md0): Mounting V5 Filesystem
XFS (md0): Starting recovery (logdev: internal)
XFS (md0): Unknown buffer type 0!
XFS (md0): _xfs_buf_ioapply: no ops on block 0xaea8802/0x1
ffff8800ffc53800: 58 41 47 49 .....

Which is the AGI buffer magic number.

Ensure that we set the type appropriately in both unlink list
addition and removal.
Tested-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 0d612fb5 upstream.

Jan Kara reported that log recovery was finding buffers with invalid
types in them. This should not happen, and indicates a bug in the
logging of buffers. To catch this, add asserts to the buffer
formatting code to ensure that the buffer type is in range when the
transaction is committed.

We don't set a type on buffers being marked stale - they are not
going to get replayed, the format item exists only for recovery to
be able to prevent replay of the buffer, so the type does not
matter. Hence that needs special casing here.
Reported-by: Jan Kara <jack@suse.cz>
Tested-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 19acc77a upstream.

There was a bad typo in commit 43759d4f ("random: use an improved
fast_mix() function") and I didn't notice because it "looked right", so
I saw what I expected to see when I reviewed it.

Only months later did I look and notice it's not the Threefish-inspired
mix function that I had designed and optimized.

Mea Culpa.  Each input bit still has a chance to affect each output bit,
and the fast pool is spilled *long* before it fills, so it's not a total
disaster, but it's definitely not the intended great improvement.

I'm still working on finding better rotation constants.  These are good
enough, but since it's unrolled twice, it's possible to get better
mixing for free by using eight different constants rather than repeating
the same four.
Signed-off-by: George Spelvin <linux@horizon.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8f0c304c upstream.

Please add support for sub BT chip on the combo card
Broadcom 43142A0 (in Lenovo E145), 04ca:2007

/sys/kernel/debug/usb/devices

T:  Bus=05 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04ca ProdID=2007 Rev= 1.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM43142A0
S:  SerialNumber=28E347EC73BD
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Firmware for 04ca:2007 can be extracted from the latest Lenovo E145
Bluetooth driver for Windows (driver is however described as BCM20702
but contains also firwmare for BCM43142).
Search for BCM43142A0_001.001.011.0122.0153.hex within hex files, then
it must be converted using hex2hcd utility. Rename file to
BCM43142A0-04ca-2007.hcd, then move to /lib/firmware/brcm/.
Signed-off-by: Matej Dubovy <matej.dubovy@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d049f4e5 upstream.

The Dynex/Insignia USB dongles are Broadcom BCM20702B0 based and require
firmware update before operation.

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=19ff ProdID=0239 Rev= 1.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM20702A0
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Since this is an unsual USB vendor ID (0x19ff), these dongles are added
via USB_DEVICE macro and not USB_VENDOR_AND_INTERFACE_INFO as done for
mainstream Broadcom based dongles.

The latest known working firmware is BCM20702B0_002.001.014.0527.0557.hex
which needs to be converted using hex2hcd utility and then installed
as /lib/firmware/brcm/BCM20702A0-19ff-0239.hcd to make this device fully
operational.

Bluetooth: hci0: BCM: patching hci_ver=06 hci_rev=2000 lmp_ver=06 lmp_subver=410e
Bluetooth: hci0: BCM: firmware hci_ver=06 hci_rev=222d lmp_ver=06 lmp_subver=410e

With this firmware the device reports support for connectionless slave
broadcast (master and slave) feature used by 3D Glasses and TVs.

  < HCI Command: Read Local Extended Features (0x04|0x0004) plen 1
          Page: 2
  > HCI Event: Command Complete (0x0e) plen 14
        Read Local Extended Features (0x04|0x0004) ncmd 1
          Status: Success (0x00)
          Page: 2/2
          Features: 0x0f 0x00 0x00 0x00 0x00 0x00 0x00 0x00
            Connectionless Slave Broadcast - Master
            Connectionless Slave Broadcast - Slave
            Synchronization Train
            Synchronization Scan

However there are some flaws with this feature. The Set Event Mask Page 2
command is actually not supported and with that all connectionless slave
broadcast events are always enabled.

  < HCI Command: Set Event Mask Page 2 (0x03|0x0063) plen 8
          Mask: 0x00000000000f0000
            Synchronization Train Received
            Connectionless Slave Broadcast Receive
            Connectionless Slave Broadcast Timeout
            Truncated Page Complete
  > HCI Event: Command Complete (0x0e) plen 4
        Set Event Mask Page 2 (0x03|0x0063) ncmd 1
          Status: Unknown HCI Command (0x01)

In addition the Synchronization Train Received event is actually broken
on this controller. It mixes up the order of parameters. According to the
Bluetooth Core specification the fields are like this:

  struct hci_ev_sync_train_received {
          __u8     status;
          bdaddr_t bdaddr;
          __le32   offset;
          __u8     map[10];
          __u8     lt_addr;
          __le32   instant;
          __le16   interval;
          __u8     service_data;
  } __packed;

This controller however sends the service_data as 5th parameter instead
of having it as last parameter.

  struct hci_ev_sync_train_received {
          __u8     status;
          bdaddr_t bdaddr;
          __le32   offset;
          __u8     map[10];
          __u8     service_data;
          __u8     lt_addr;
          __le32   instant;
          __le16   interval;
  } __packed;

So anybody trying to use this hardware for utilizing connectionless slave
broadcast receivers (aka 3D Glasses), be warned about this shortcoming.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 9a5abdaa upstream.

T:  Bus=03 Lev=01 Prnt=01 Port=06 Cnt=02 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0b05 ProdID=17cf Rev= 1.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM20702A0
S:  SerialNumber=54271E3298CD
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Firmware is extracted from the latest Broadcom BCM4352 Windows driver
by extracting the zip and searching the .hex file names for '17cf'.

The hex file must then be converted to hcd format using the hex2hcd
utility and then moved to /lib/firmware/brcm/.
Signed-off-by: Rick Dunn <rick@rickdunn.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e12af489 upstream.

According to the Bluetooth core specification valid identity addresses
are either Public Device Addresses or Static Random Addresses. IRKs
received with any other type of address should be discarded since we
cannot assume to know the permanent identity of the peer device.

This patch fixes a missing check for the Identity Address when receiving
the Identity Address Information SMP PDU.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 033efa92 upstream.

Add support of 13d3:3423 device.

BugLink: https://bugs.launchpad.net/bugs/1411193

T: Bus=01 Lev=02 Prnt=03 Port=00 Cnt=01 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3423 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c561a575 upstream.

BugLink: https://bugs.launchpad.net/bugs/1400215

ath3k devices fail to load firmwares on xHCI buses, but work well on
EHCI, this might be a compatibility issue between xHCI and ath3k chips.
As my testing result, those chips will work on xHCI buses again with
this patch.

This workaround is from Qualcomm, they also did some workarounds in
Windows driver.
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a8f29e89 upstream.

Userspace expects to see a long space before the first pulse is sent on
the lirc device.  Currently, if a long time has passed and a new packet
is started, the lirc codec just returns and doesn't send anything.  This
makes lircd ignore many perfectly valid signals unless they are sent in
quick sucession.  When a reset event is delivered, we cannot know
anything about the duration of the space.  But it should be safe to
assume it has been a long time and we just set the duration to maximum.
Signed-off-by: Austin Lund <austin.lund@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2d5b86e0 upstream.

As of v3.18, ext4 started rejecting a remount which changes the
journal_checksum option.

Prior to that, it was simply ignored; the problem here is that
if someone has this in their fstab for the root fs, now the box
fails to boot properly, because remount of root with the new options
will fail, and the box proceeds with a readonly root.

I think it is a little nicer behavior to accept the option, but
warn that it's being ignored, rather than failing the mount,
but that might be a subjective matter...
Reported-by: Cónräd <conradsand.arma@gmail.com>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 0d32ef8c ]

Doing the following commands on a non idle network device
panics the box instantly, because cpu_bstats gets overwritten
by stats.

tc qdisc add dev eth0 root <your_favorite_qdisc>
... some traffic (one packet is enough) ...
tc qdisc replace dev eth0 root est 1sec 4sec <your_favorite_qdisc>

[  325.355596] BUG: unable to handle kernel paging request at ffff8841dc5a074c
[  325.362609] IP: [<ffffffff81541c9e>] __gnet_stats_copy_basic+0x3e/0x90
[  325.369158] PGD 1fa7067 PUD 0
[  325.372254] Oops: 0000 [#1] SMP
[  325.375514] Modules linked in: ...
[  325.398346] CPU: 13 PID: 14313 Comm: tc Not tainted 3.19.0-smp-DEV #1163
[  325.412042] task: ffff8800793ab5d0 ti: ffff881ff2fa4000 task.ti: ffff881ff2fa4000
[  325.419518] RIP: 0010:[<ffffffff81541c9e>]  [<ffffffff81541c9e>] __gnet_stats_copy_basic+0x3e/0x90
[  325.428506] RSP: 0018:ffff881ff2fa7928  EFLAGS: 00010286
[  325.433824] RAX: 000000000000000c RBX: ffff881ff2fa796c RCX: 000000000000000c
[  325.440988] RDX: ffff8841dc5a0744 RSI: 0000000000000060 RDI: 0000000000000060
[  325.448120] RBP: ffff881ff2fa7948 R08: ffffffff81cd4f80 R09: 0000000000000000
[  325.455268] R10: ffff883ff223e400 R11: 0000000000000000 R12: 000000015cba0744
[  325.462405] R13: ffffffff81cd4f80 R14: ffff883ff223e460 R15: ffff883feea0722c
[  325.469536] FS:  00007f2ee30fa700(0000) GS:ffff88407fa20000(0000) knlGS:0000000000000000
[  325.477630] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  325.483380] CR2: ffff8841dc5a074c CR3: 0000003feeae9000 CR4: 00000000001407e0
[  325.490510] Stack:
[  325.492524]  ffff883feea0722c ffff883fef719dc0 ffff883feea0722c ffff883ff223e4a0
[  325.499990]  ffff881ff2fa79a8 ffffffff815424ee ffff883ff223e49c 000000015cba0744
[  325.507460]  00000000f2fa7978 0000000000000000 ffff881ff2fa79a8 ffff883ff223e4a0
[  325.514956] Call Trace:
[  325.517412]  [<ffffffff815424ee>] gen_new_estimator+0x8e/0x230
[  325.523250]  [<ffffffff815427aa>] gen_replace_estimator+0x4a/0x60
[  325.529349]  [<ffffffff815718ab>] tc_modify_qdisc+0x52b/0x590
[  325.535117]  [<ffffffff8155edd0>] rtnetlink_rcv_msg+0xa0/0x240
[  325.540963]  [<ffffffff8155ed30>] ? __rtnl_unlock+0x20/0x20
[  325.546532]  [<ffffffff8157f811>] netlink_rcv_skb+0xb1/0xc0
[  325.552145]  [<ffffffff8155b355>] rtnetlink_rcv+0x25/0x40
[  325.557558]  [<ffffffff8157f0d8>] netlink_unicast+0x168/0x220
[  325.563317]  [<ffffffff8157f47c>] netlink_sendmsg+0x2ec/0x3e0

Lets play safe and not use an union : percpu 'pointers' are mostly read
anyway, and we have typically few qdiscs per host.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Fixes: 22e0f8b9 ("net: sched: make bstats per cpu and estimator RCU safe")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit d953ca4d ]

The existing code frees the skb in EAGAIN case, in which the skb will be
retried from upper layer and used again.
Also, the existing code doesn't free send buffer slot in error case, because
there is no completion message for unsent packets.
This patch fixes these problems.

(Please also include this patch for stable trees. Thanks!)
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit cfbf654e ]

When making use of RFC5061, section 4.2.4. for setting the primary IP
address, we're passing a wrong parameter header to param_type2af(),
resulting always in NULL being returned.

At this point, param.p points to a sctp_addip_param struct, containing
a sctp_paramhdr (type = 0xc004, length = var), and crr_id as a correlation
id. Followed by that, as also presented in RFC5061 section 4.2.4., comes
the actual sctp_addr_param, which also contains a sctp_paramhdr, but
this time with the correct type SCTP_PARAM_IPV{4,6}_ADDRESS that
param_type2af() can make use of. Since we already hold a pointer to
addr_param from previous line, just reuse it for param_type2af().

Fixes: d6de3097 ("[SCTP]: Add the handling of "Set Primary IP Address" parameter to INIT")
Signed-off-by: Saran Maruti Ramanara <saran.neti@telus.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit e2a4800e ]

When we've run out of space in the output buffer to store more data, we
will call zlib_deflate with a NULL output buffer until we've consumed
remaining input.

When this happens, olen contains the size the output buffer would have
consumed iff we'd have had enough room.

This can later cause skb_over_panic when ppp_generic skb_put()s
the returned length.
Reported-by: Iain Douglas <centos@1n6.org.uk>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit bdbbb852 ]

In commit be9f4a44 ("ipv4: tcp: remove per net tcp_sock")
I tried to address contention on a socket lock, but the solution
I chose was horrible :

commit 3a7c384f ("ipv4: tcp: unicast_sock should not land outside
of TCP stack") addressed a selinux regression.

commit 0980e56e ("ipv4: tcp: set unicast_sock uc_ttl to -1")
took care of another regression.

commit b5ec8eea ("ipv4: fix ip_send_skb()") fixed another regression.

commit 811230cd ("tcp: ipv4: initialize unicast_sock sk_pacing_rate")
was another shot in the dark.

Really, just use a proper socket per cpu, and remove the skb_orphan()
call, to re-enable flow control.

This solves a serious problem with FQ packet scheduler when used in
hostile environments, as we do not want to allocate a flow structure
for every RST packet sent in response to a spoofed packet.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 811230cd ]

When I added sk_pacing_rate field, I forgot to initialize its value
in the per cpu unicast_sock used in ip_send_unicast_reply()

This means that for sch_fq users, RST packets, or ACK packets sent
on behalf of TIME_WAIT sockets might be sent to slowly or even dropped
once we reach the per flow limit.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 95bd09eb ("tcp: TSO packets automatic sizing")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 59ccaaaa ]

Reported in: https://bugzilla.kernel.org/show_bug.cgi?id=92081

This patch avoids calling rtnl_notify if the device ndo_bridge_getlink
handler does not return any bytes in the skb.

Alternately, the skb->len check can be moved inside rtnl_notify.

For the bridge vlan case described in 92081, there is also a fix needed
in bridge driver to generate a proper notification. Will fix that in
subsequent patch.

v2: rebase patch on net tree
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 06539d30 ]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 24e579c8 ]

With the commit d75b1ade ("net: less interrupt masking in NAPI") napi
repoll is done only when work_done == budget. When in busy_poll is we return 0
in napi_poll. We should return budget.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 6e9e16e6 ]

Lubomir Rintel reported that during replacing a route the interface
reference counter isn't correctly decremented.

To quote bug <https://bugzilla.kernel.org/show_bug.cgi?id=91941>:
| [root@rhel7-5 lkundrak]# sh -x lal
| + ip link add dev0 type dummy
| + ip link set dev0 up
| + ip link add dev1 type dummy
| + ip link set dev1 up
| + ip addr add 2001:db8:8086::2/64 dev dev0
| + ip route add 2001:db8:8086::/48 dev dev0 proto static metric 20
| + ip route add 2001:db8:8088::/48 dev dev1 proto static metric 10
| + ip route replace 2001:db8:8086::/48 dev dev1 proto static metric 20
| + ip link del dev0 type dummy
| Message from syslogd@rhel7-5 at Jan 23 10:54:41 ...
|  kernel:unregister_netdevice: waiting for dev0 to become free. Usage count = 2
|
| Message from syslogd@rhel7-5 at Jan 23 10:54:51 ...
|  kernel:unregister_netdevice: waiting for dev0 to become free. Usage count = 2

During replacement of a rt6_info we must walk all parent nodes and check
if the to be replaced rt6_info got propagated. If so, replace it with
an alive one.

Fixes: 4a287eba ("IPv6 routing, NLM_F_* flag support: REPLACE and EXCL flags support, warn about missing CREATE flag")
Reported-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Tested-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit fc752f1f ]

An exception is seen in ICMP ping receive path where the skb
destructor sock_rfree() tries to access a freed socket. This happens
because ping_rcv() releases socket reference with sock_put() and this
internally frees up the socket. Later icmp_rcv() will try to free the
skb and as part of this, skb destructor is called and which leads
to a kernel panic as the socket is freed already in ping_rcv().

-->|exception
-007|sk_mem_uncharge
-007|sock_rfree
-008|skb_release_head_state
-009|skb_release_all
-009|__kfree_skb
-010|kfree_skb
-011|icmp_rcv
-012|ip_local_deliver_finish

Fix this incorrect free by cloning this skb and processing this cloned
skb instead.

This patch was suggested by Eric Dumazet
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 86f3cddb ]

While working on rhashtable walking I noticed that the UDP diag
dumping code is buggy.  In particular, the socket skipping within
a chain never happens, even though we record the number of sockets
that should be skipped.

As this code was supposedly copied from TCP, this patch does what
TCP does and resets num before we walk a chain.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit df4d9254 ]

Not caching dst_entries which cause redirects could be exploited by hosts
on the same subnet, causing a severe DoS attack. This effect aggravated
since commit f8864972 ("ipv4: fix dst race in sk_dst_get()").

Lookups causing redirects will be allocated with DST_NOCACHE set which
will force dst_release to free them via RCU.  Unfortunately waiting for
RCU grace period just takes too long, we can end up with >1M dst_entries
waiting to be released and the system will run OOM. rcuos threads cannot
catch up under high softirq load.

Attaching the flag to emit a redirect later on to the specific skb allows
us to cache those dst_entries thus reducing the pressure on allocation
and deallocation.

This issue was discovered by Marcelo Leitner.

Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Marcelo Leitner <mleitner@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 600ddd68 ]

When hitting an INIT collision case during the 4WHS with AUTH enabled, as
already described in detail in commit 1be9a950 ("net: sctp: inherit
auth_capable on INIT collisions"), it can happen that we occasionally
still remotely trigger the following panic on server side which seems to
have been uncovered after the fix from commit 1be9a950 ...

[  533.876389] BUG: unable to handle kernel paging request at 00000000ffffffff
[  533.913657] IP: [<ffffffff811ac385>] __kmalloc+0x95/0x230
[  533.940559] PGD 5030f2067 PUD 0
[  533.957104] Oops: 0000 [#1] SMP
[  533.974283] Modules linked in: sctp mlx4_en [...]
[  534.939704] Call Trace:
[  534.951833]  [<ffffffff81294e30>] ? crypto_init_shash_ops+0x60/0xf0
[  534.984213]  [<ffffffff81294e30>] crypto_init_shash_ops+0x60/0xf0
[  535.015025]  [<ffffffff8128c8ed>] __crypto_alloc_tfm+0x6d/0x170
[  535.045661]  [<ffffffff8128d12c>] crypto_alloc_base+0x4c/0xb0
[  535.074593]  [<ffffffff8160bd42>] ? _raw_spin_lock_bh+0x12/0x50
[  535.105239]  [<ffffffffa0418c11>] sctp_inet_listen+0x161/0x1e0 [sctp]
[  535.138606]  [<ffffffff814e43bd>] SyS_listen+0x9d/0xb0
[  535.166848]  [<ffffffff816149a9>] system_call_fastpath+0x16/0x1b

... or depending on the the application, for example this one:

[ 1370.026490] BUG: unable to handle kernel paging request at 00000000ffffffff
[ 1370.026506] IP: [<ffffffff811ab455>] kmem_cache_alloc+0x75/0x1d0
[ 1370.054568] PGD 633c94067 PUD 0
[ 1370.070446] Oops: 0000 [#1] SMP
[ 1370.085010] Modules linked in: sctp kvm_amd kvm [...]
[ 1370.963431] Call Trace:
[ 1370.974632]  [<ffffffff8120f7cf>] ? SyS_epoll_ctl+0x53f/0x960
[ 1371.000863]  [<ffffffff8120f7cf>] SyS_epoll_ctl+0x53f/0x960
[ 1371.027154]  [<ffffffff812100d3>] ? anon_inode_getfile+0xd3/0x170
[ 1371.054679]  [<ffffffff811e3d67>] ? __alloc_fd+0xa7/0x130
[ 1371.080183]  [<ffffffff816149a9>] system_call_fastpath+0x16/0x1b

With slab debugging enabled, we can see that the poison has been overwritten:

[  669.826368] BUG kmalloc-128 (Tainted: G        W     ): Poison overwritten
[  669.826385] INFO: 0xffff880228b32e50-0xffff880228b32e50. First byte 0x6a instead of 0x6b
[  669.826414] INFO: Allocated in sctp_auth_create_key+0x23/0x50 [sctp] age=3 cpu=0 pid=18494
[  669.826424]  __slab_alloc+0x4bf/0x566
[  669.826433]  __kmalloc+0x280/0x310
[  669.826453]  sctp_auth_create_key+0x23/0x50 [sctp]
[  669.826471]  sctp_auth_asoc_create_secret+0xcb/0x1e0 [sctp]
[  669.826488]  sctp_auth_asoc_init_active_key+0x68/0xa0 [sctp]
[  669.826505]  sctp_do_sm+0x29d/0x17c0 [sctp] [...]
[  669.826629] INFO: Freed in kzfree+0x31/0x40 age=1 cpu=0 pid=18494
[  669.826635]  __slab_free+0x39/0x2a8
[  669.826643]  kfree+0x1d6/0x230
[  669.826650]  kzfree+0x31/0x40
[  669.826666]  sctp_auth_key_put+0x19/0x20 [sctp]
[  669.826681]  sctp_assoc_update+0x1ee/0x2d0 [sctp]
[  669.826695]  sctp_do_sm+0x674/0x17c0 [sctp]

Since this only triggers in some collision-cases with AUTH, the problem at
heart is that sctp_auth_key_put() on asoc->asoc_shared_key is called twice
when having refcnt 1, once directly in sctp_assoc_update() and yet again
from within sctp_auth_asoc_init_active_key() via sctp_assoc_update() on
the already kzfree'd memory, which is also consistent with the observation
of the poison decrease from 0x6b to 0x6a (note: the overwrite is detected
at a later point in time when poison is checked on new allocation).

Reference counting of auth keys revisited:

Shared keys for AUTH chunks are being stored in endpoints and associations
in endpoint_shared_keys list. On endpoint creation, a null key is being
added; on association creation, all endpoint shared keys are being cached
and thus cloned over to the association. struct sctp_shared_key only holds
a pointer to the actual key bytes, that is, struct sctp_auth_bytes which
keeps track of users internally through refcounting. Naturally, on assoc
or enpoint destruction, sctp_shared_key are being destroyed directly and
the reference on sctp_auth_bytes dropped.

User space can add keys to either list via setsockopt(2) through struct
sctp_authkey and by passing that to sctp_auth_set_key() which replaces or
adds a new auth key. There, sctp_auth_create_key() creates a new sctp_auth_bytes
with refcount 1 and in case of replacement drops the reference on the old
sctp_auth_bytes. A key can be set active from user space through setsockopt()
on the id via sctp_auth_set_active_key(), which iterates through either
endpoint_shared_keys and in case of an assoc, invokes (one of various places)
sctp_auth_asoc_init_active_key().

sctp_auth_asoc_init_active_key() computes the actual secret from local's
and peer's random, hmac and shared key parameters and returns a new key
directly as sctp_auth_bytes, that is asoc->asoc_shared_key, plus drops
the reference if there was a previous one. The secret, which where we
eventually double drop the ref comes from sctp_auth_asoc_set_secret() with
intitial refcount of 1, which also stays unchanged eventually in
sctp_assoc_update(). This key is later being used for crypto layer to
set the key for the hash in crypto_hash_setkey() from sctp_auth_calculate_hmac().

To close the loop: asoc->asoc_shared_key is freshly allocated secret
material and independant of the sctp_shared_key management keeping track
of only shared keys in endpoints and assocs. Hence, also commit 4184b2a7
("net: sctp: fix memory leak in auth key management") is independant of
this bug here since it concerns a different layer (though same structures
being used eventually). asoc->asoc_shared_key is reference dropped correctly
on assoc destruction in sctp_association_free() and when active keys are
being replaced in sctp_auth_asoc_init_active_key(), it always has a refcount
of 1. Hence, it's freed prematurely in sctp_assoc_update(). Simple fix is
to remove that sctp_auth_key_put() from there which fixes these panics.

Fixes: 730fc3d0 ("[SCTP]: Implete SCTP-AUTH parameter processing")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 6088beef ]

NAPI poll logic now enforces that a poller returns exactly the budget
when it wants to be called again.

If a driver limits TX completion, it has to return budget as well when
the limit is hit, not the number of received packets.
Reported-and-tested-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: d75b1ade ("net: less interrupt masking in NAPI")
Cc: Manish Chopra <manish.chopra@qlogic.com>
Acked-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 9d289715 ]

Reduce the attack vector and stop generating IPv6 Fragment Header for
paths with an MTU smaller than the minimum required IPv6 MTU
size (1280 byte) - called atomic fragments.

See IETF I-D "Deprecating the Generation of IPv6 Atomic Fragments" [1]
for more information and how this "feature" can be misused.

[1] https://tools.ietf.org/html/draft-ietf-6man-deprecate-atomfrag-generation-00Signed-off-by: Fernando Gont <fgont@si6networks.com>
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit ac64da0b ]

softnet_data.input_pkt_queue is protected by a spinlock that
we must hold when transferring packets from victim queue to an active
one. This is because other cpus could still be trying to enqueue packets
into victim queue.

A second problem is that when we transfert the NAPI poll_list from
victim to current cpu, we absolutely need to special case the percpu
backlog, because we do not want to add complex locking to protect
process_queue : Only owner cpu is allowed to manipulate it, unless cpu
is offline.

Based on initial patch from Prasad Sodagudi & Subash Abhinov
Kasiviswanathan.

This version is better because we do not slow down packet processing,
only make migration safer.
Reported-by: Prasad Sodagudi <psodagud@codeaurora.org>
Reported-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit f812116b ]

The sockaddr is returned in IP(V6)_RECVERR as part of errhdr. That
structure is defined and allocated on the stack as

    struct {
            struct sock_extended_err ee;
            struct sockaddr_in(6)    offender;
    } errhdr;

The second part is only initialized for certain SO_EE_ORIGIN values.
Always initialize it completely.

An MTU exceeded error on a SOCK_RAW/IPPROTO_RAW is one example that
would return uninitialized bytes.
Signed-off-by: Willem de Bruijn <willemb@google.com>

----

Also verified that there is no padding between errhdr.ee and
errhdr.offender that could leak additional kernel data.
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 7fb08eca upstream.

This replaces four copies in various stages of mm_fault_error() handling
with just a single one.  It will also allow for more natural placement
of the unlocking after some further cleanup.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6c8465a8 upstream.

When taking a CPU down for suspend and resume, a tracepoint may be called
when the CPU has been designated offline. As tracepoints require RCU for
protection, they must not be called if the current CPU is offline.

Unfortunately, trace_tlb_flush() is called in this scenario as was noted
by LOCKDEP:

...

 Disabling non-boot CPUs ...
 intel_pstate CPU 1 exiting

 ===============================
 smpboot: CPU 1 didn't die...
 [ INFO: suspicious RCU usage. ]
 3.19.0-rc7-next-20150204.1-iniza-small #1 Not tainted
 -------------------------------
 include/trace/events/tlb.h:35 suspicious rcu_dereference_check() usage!

 other info that might help us debug this:

 RCU used illegally from offline CPU!
 rcu_scheduler_active = 1, debug_locks = 0
 no locks held by swapper/1/0.

 stack backtrace:
 CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.19.0-rc7-next-20150204.1-iniza-small #1
 Hardware name: SAMSUNG ELECTRONICS CO., LTD. 530U3BI/530U4BI/530U4BH/530U3BI/530U4BI/530U4BH, BIOS 13XK 03/28/2013
  0000000000000001 ffff88011a44fe18 ffffffff817e370d 0000000000000011
  ffff88011a448290 ffff88011a44fe48 ffffffff810d6847 ffff8800c66b9600
  0000000000000001 ffff88011a44c000 ffffffff81cb3900 ffff88011a44fe78
 Call Trace:
  [<ffffffff817e370d>] dump_stack+0x4c/0x65
  [<ffffffff810d6847>] lockdep_rcu_suspicious+0xe7/0x120
  [<ffffffff810b71a5>] idle_task_exit+0x205/0x2c0
  [<ffffffff81054c4e>] play_dead_common+0xe/0x50
  [<ffffffff81054ca5>] native_play_dead+0x15/0x140
  [<ffffffff8102963f>] arch_cpu_idle_dead+0xf/0x20
  [<ffffffff810cd89e>] cpu_startup_entry+0x37e/0x580
  [<ffffffff81053e20>] start_secondary+0x140/0x150
 intel_pstate CPU 2 exiting

...

By converting the tlb_flush tracepoint to a TRACE_EVENT_CONDITION where the
condition is cpu_online(smp_processor_id()), we can avoid calling RCU protected
code when the CPU is offline.

Link: http://lkml.kernel.org/r/CA+icZUUGiGDoL5NU8RuxKzFjoLjEKRtUWx=JB8B9a0EQv-eGzQ@mail.gmail.com

Fixes: d17d8f9d "x86/mm: Add tracepoints for TLB flushes"
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Suggested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Hansen <dave@sr71.net>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>