Add bindings for thermal monitor, part of Qualcomm PMIC5 chips. It is a
close counterpart of VADC part of those PMICs.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210205000118.493610-2-dmitry.baryshkov@linaro.org

When we set bit 10 high we use continuous mode and not single
mode. Let's correct this to avoid confusion. No functional
changes here, the code does the right thing with bit 10.

Cc: Adam Ford <aford173@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210205134534.49200-5-tony@atomide.com

We can use iopoll for checking the EOCZ (end of conversion) bit. And with
this we now also want to handle the timeout errors properly.

For omap3, we need about 1.2ms for the single mode sampling to wait for
EOCZ down, so let's use 1.5ms timeout there. Waiting for sampling to start
is faster and we can use 1ms timeout.

Cc: Adam Ford <aford173@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210205134534.49200-4-tony@atomide.com

At least for 4430, trying to use the single conversion mode eventually
hangs the thermal sensor. This can be quite easily seen with errors:

thermal thermal_zone0: failed to read out thermal zone (-5)

Also, trying to read the temperature shows a stuck value with:

$ while true; do cat /sys/class/thermal/thermal_zone0/temp; done

Where the temperature is not rising at all with the busy loop.

Additionally, the EOCZ (end of conversion) bit is not rising on 4430 in
single conversion mode while it works fine in continuous conversion mode.
It is also possible that the hung temperature sensor can affect the
thermal shutdown alert too.

Let's fix the issue by adding TI_BANDGAP_FEATURE_CONT_MODE_ONLY flag and
use it for 4430.

Note that we also need to add udelay to for the EOCZ (end of conversion)
bit polling as otherwise we have it time out too early on 4430. We'll be
changing the loop to use iopoll in the following clean-up patch.

Cc: Adam Ford <aford173@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210205134534.49200-3-tony@atomide.com

On dra7, there is no Start of Conversion (SOC) register bit and we have an
empty bgap_soc_mask in the configuration for the thermal driver. Let's not
do pointless reads and writes with the empty mask.

There's also no point waiting for End of Conversion bit (EOCZ) to go high
on dra7. We only care about it going down, and are now mostly timing out
waiting for EOCZ high while it has already gone down.

When we add checking for the timeout errors in a later patch, waiting for
EOCZ high would cause bogus time out errors.

Cc: Adam Ford <aford173@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210205134534.49200-2-tony@atomide.com

The zte zx platform is getting removed, so this driver is no
longer needed.

Cc: Jun Nie <jun.nie@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210120162400.4115366-3-arnd@kernel.org

The tango platform is getting removed, so the driver is no
longer needed.

Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
Cc: Mans Rullgard <mans@mansr.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210120162400.4115366-2-arnd@kernel.org

The thermal zone can have cooling devices which are missing power actor
API. This could be due to missing Energy Model for devfreq or cpufreq
cooling device. In this case it is safe to fail the binding rather than
trying to workaround and control the temperature in such thermal zone.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210119114126.19480-1-lukasz.luba@arm.com

The change of the cooling device state should be used by the governor
or at least by the core code, not by the drivers themselves.

Remove the API usage and move the function declaration to the internal
headers.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20210118173824.9970-1-daniel.lezcano@linaro.org

Like previous patch, the intel_pch_thermal device is not in ACPI
ThermalZone namespace, so a critical trip doesn't mean shutdown.

Override the default .critical callback to prevent surprising thermal
shutdoown.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201221172345.36976-2-kai.heng.feng@canonical.com

We are seeing thermal shutdown on Intel based mobile workstations, the
shutdown happens during the first trip handle in
thermal_zone_device_register():
kernel: thermal thermal_zone15: critical temperature reached (101 C), shutting down

However, we shouldn't do a thermal shutdown here, since
1) We may want to use a dedicated daemon, Intel's thermald in this case,
to handle thermal shutdown.

2) For ACPI based system, _CRT doesn't mean shutdown unless it's inside
ThermalZone namespace. ACPI Spec, 11.4.4 _CRT (Critical Temperature):
"... If this object it present under a device, the device’s driver
evaluates this object to determine the device’s critical cooling
temperature trip point. This value may then be used by the device’s
driver to program an internal device temperature sensor trip point."

So a "critical trip" here merely means we should take a more aggressive
cooling method.

As int340x device isn't present under ACPI ThermalZone, override the
default .critical callback to prevent surprising thermal shutdown.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201221172345.36976-1-kai.heng.feng@canonical.com

The function thermal_zone_device_reset() is called in the
thermal_zone_device_register() which allocates and initialize the
structure. The passive field is already zero-ed by the allocation, the
function is useless.

Call directly thermal_zone_device_init() instead and
thermal_zone_device_reset().
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201222181110.1231977-1-daniel.lezcano@linaro.org

The code does no longer use the ms unit based fields to set the
delays as they are replaced by the jiffies.

Remove them and replace their user to use the jiffies version instead.

Cc: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Peter Kästle <peter@piie.net>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201216220337.839878-3-daniel.lezcano@linaro.org

The delays are also stored in jiffies based unit. Use them instead of
the ms.

Cc: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Link: https://lore.kernel.org/r/20201216220337.839878-2-daniel.lezcano@linaro.org

The delays are stored in ms units and when the polling function is
called this delay is converted into jiffies at each call.

Instead of doing the conversion again and again, compute the jiffies
at init time and use the value directly when setting the polling.

Cc: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Link: https://lore.kernel.org/r/20201216220337.839878-1-daniel.lezcano@linaro.org

The macro THERMAL_TRIPS_NONE is no longer used, remove it.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Link: https://lore.kernel.org/r/20201214233811.485669-6-daniel.lezcano@linaro.org

The last site calling the thermal_zone_bind_cooling_device() function
with the THERMAL_TRIPS_NONE parameter was removed.

We can get rid of this test as no user of this function is calling
this function with this parameter.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Link: https://lore.kernel.org/r/20201214233811.485669-5-daniel.lezcano@linaro.org

The loop is here to create default cooling device binding on the
THERMAL_TRIPS_NONE number which is used to be the 'forced_passive'
feature. However, we removed all code dealing with that in the thermal
core, thus this binding does no longer make sense.

Remove it.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Link: https://lore.kernel.org/r/20201214233811.485669-4-daniel.lezcano@linaro.org

The THERMAL_TRIPS_NONE is equal to -1, it is pointless to do a
conversion in this function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Link: https://lore.kernel.org/r/20201214233811.485669-3-daniel.lezcano@linaro.org

The functions thermal_zone_device_rebind_exception and
thermal_zone_device_unbind_exception are not used from anywhere.

Remove that code.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Link: https://lore.kernel.org/r/20201214233811.485669-2-daniel.lezcano@linaro.org

The code was reorganized in 2012 with the commit 0c01ebbf.

The main change is a loop on the trip points array and a unconditional
call to the throttle() ops of the governors for each of them even if
the trip temperature is not reached yet.

With this change, the 'forced_passive' is no longer checked in the
thermal_zone_device_update() function but in the step wise governor's
throttle() callback.

As the force_passive does no belong to the trip point array, the
thermal_zone_device_update() can not compare with the specified
passive temperature, thus does not detect the passive limit has been
crossed. Consequently, throttle() is never called and the
'forced_passive' branch is unreached.

In addition, the default processor cooling device is not automatically
bound to the thermal zone if there is not passive trip point, thus the
'forced_passive' can not operate.

If there is an active trip point, then the throttle function will be
called to mitigate at this temperature and the 'forced_passive' will
override the mitigation of the active trip point in this case but with
the default cooling device bound to the thermal zone, so usually a
fan, and that is not a passive cooling effect.

Given the regression exists since more than 8 years, nobody complained
and at the best of my knowledge there is no bug open in
https://bugzilla.kernel.org, it is reasonable to say it is unused.

Remove the 'forced_passive' related code.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Link: https://lore.kernel.org/r/20201214233811.485669-1-daniel.lezcano@linaro.org

Scale adcmap_100k_104ef_104fb temp values by the factor of 1000 to
remove extra multiplication in qcom_vadc_scale_therm().
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201204025509.1075506-12-dmitry.baryshkov@linaro.orgSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

All volt-temp tables here are sorted in descending order. There is no
need to accout for (unused) ascending table sorting case, so simplify
the conversion function.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201204025509.1075506-11-dmitry.baryshkov@linaro.orgSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

qcom_vadc7_scale_hw_calib_die_temp() uses a table format different from
the rest of volt/temp conversion functions in this file. Also the
conversion functions results in non-monothonic values conversion, which
seems wrong.

Rewrite qcom_vadc7_scale_hw_calib_die_temp() to use
qcom_vadc_map_voltage_temp() directly, like the rest of conversion
functions do.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201204025509.1075506-10-dmitry.baryshkov@linaro.orgSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

struct vadc_map_pt is not used outside of qcom-vadc-common.c, so move it
there from the global header file.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201204025509.1075506-9-dmitry.baryshkov@linaro.orgSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

There might be cases when the IIO channel is attached to the device
subnode instead of being attached to the main device node. Allow drivers
to query IIO channels by using device tree nodes.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201204025509.1075506-8-dmitry.baryshkov@linaro.orgSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Use of_device_get_match_data() instead of hand-coding it manually.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20201204025509.1075506-7-dmitry.baryshkov@linaro.orgSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

qcom-vadc-common module will be used by ADC thermal monitoring driver,
so move it to global include dir.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201204025509.1075506-6-dmitry.baryshkov@linaro.orgSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Use new function fixp_linear_interpolate() instead of hand-coding the
linear interpolation.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201204025509.1075506-5-dmitry.baryshkov@linaro.orgSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

ADC-TM5 driver will make use of several functions from ADC5 driver. Move
them to qcom-vadc-common driver.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201204025509.1075506-4-dmitry.baryshkov@linaro.orgSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Adds a function to interpolate against two points,
this is carried arount as a helper function by tons of drivers.
Signed-off-by: Craig Tatlor <ctatlor97@gmail.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201204025509.1075506-3-dmitry.baryshkov@linaro.orgSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

With the removal of the notifys user in a previous patches, the ops is no
longer needed, remove it.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lore.kernel.org/r/20201210121514.25760-5-daniel.lezcano@linaro.org

The acpi driver wants to do a netlink notification in case of a hot or
critical trip point. Implement the corresponding ops to be used for
the thermal zone and use them instead of the notify ops.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20201210121514.25760-3-daniel.lezcano@linaro.org

Pull s390 cleanups from Vasily Gorbik:
 "Update defconfigs and sort config select list"

* tag 's390-5.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/Kconfig: sort config S390 select list once again
  s390: update defconfigs

Pull power management fixes from Rafael Wysocki:
 "These fix a crash in intel_pstate during resume from suspend-to-RAM
  that may occur after recent changes and two resource leaks in error
  paths in the operating performance points (OPP) framework, add a new
  C-states table to intel_idle and update the cpuidle MAINTAINERS entry
  to cover the governors too.

  Specifics:

   - Fix recently introduced crash in the intel_pstate driver that
     occurs if scale-invariance is disabled during resume from
     suspend-to-RAM due to inconsistent changes of APERF or MPERF MSR
     values made by the platform firmware (Rafael Wysocki).

   - Fix a memory leak and add a missing clk_put() in error paths in the
     OPP framework (Quanyang Wang, Viresh Kumar).

   - Add new C-states table for SnowRidge processors to the intel_idle
     driver (Artem Bityutskiy).

   - Update the MAINTAINERS entry for cpuidle to make it clear that the
     governors are covered by it too (Lukas Bulwahn)"

* tag 'pm-5.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  intel_idle: add SnowRidge C-state table
  cpufreq: intel_pstate: Fix fast-switch fallback path
  opp: Call the missing clk_put() on error
  opp: fix memory leak in _allocate_opp_table
  MAINTAINERS: include governors into CPU IDLE TIME MANAGEMENT FRAMEWORK

* pm-cpufreq:
  cpufreq: intel_pstate: Fix fast-switch fallback path

* pm-cpuidle:
  intel_idle: add SnowRidge C-state table
  MAINTAINERS: include governors into CPU IDLE TIME MANAGEMENT FRAMEWORK

Pull SCSI fixes from James Bottomley:
 "This is a load of driver fixes (12 ufs, 1 mpt3sas, 1 cxgbi).

  The big core two fixes are for power management ("block: Do not accept
  any requests while suspended" and "block: Fix a race in the runtime
  power management code") which finally sorts out the resume problems
  we've occasionally been having.

  To make the resume fix, there are seven necessary precursors which
  effectively renames REQ_PREEMPT to REQ_PM, so every "special" request
  in block is automatically a power management exempt one.

  All of the non-PM preempt cases are removed except for the one in the
  SCSI Parallel Interface (spi) domain validation which is a genuine
  case where we have to run requests at high priority to validate the
  bus so this becomes an autopm get/put protected request"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (22 commits)
  scsi: cxgb4i: Fix TLS dependency
  scsi: ufs: Un-inline ufshcd_vops_device_reset function
  scsi: ufs: Re-enable WriteBooster after device reset
  scsi: ufs-mediatek: Use correct path to fix compile error
  scsi: mpt3sas: Signedness bug in _base_get_diag_triggers()
  scsi: block: Do not accept any requests while suspended
  scsi: block: Remove RQF_PREEMPT and BLK_MQ_REQ_PREEMPT
  scsi: core: Only process PM requests if rpm_status != RPM_ACTIVE
  scsi: scsi_transport_spi: Set RQF_PM for domain validation commands
  scsi: ide: Mark power management requests with RQF_PM instead of RQF_PREEMPT
  scsi: ide: Do not set the RQF_PREEMPT flag for sense requests
  scsi: block: Introduce BLK_MQ_REQ_PM
  scsi: block: Fix a race in the runtime power management code
  scsi: ufs-pci: Enable UFSHCD_CAP_RPM_AUTOSUSPEND for Intel controllers
  scsi: ufs-pci: Fix recovery from hibernate exit errors for Intel controllers
  scsi: ufs-pci: Ensure UFS device is in PowerDown mode for suspend-to-disk ->poweroff()
  scsi: ufs-pci: Fix restore from S4 for Intel controllers
  scsi: ufs-mediatek: Keep VCC always-on for specific devices
  scsi: ufs: Allow regulators being always-on
  scsi: ufs: Clear UAC for RPMB after ufshcd resets
  ...

Pull block fixes from Jens Axboe:
 "Two minor block fixes from this last week that should go into 5.11:

   - Add missing NOWAIT debugfs definition (Andres)

   - Fix kerneldoc warning introduced this merge window (Randy)"

* tag 'block-5.11-2021-01-01' of git://git.kernel.dk/linux-block:
  block: add debugfs stanza for QUEUE_FLAG_NOWAIT
  fs: block_dev.c: fix kernel-doc warnings from struct block_device changes