Merge tag 'v4.5-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt

Merge "rockchip dts32 changes for 4.5" from Heiko Stuebner:

First round of arm devicetree changes.
Among the bigger changes are two new Veyron boards, support for
the dual-core cortex-a7 rk3036 soc and addition of support for
the crypto engine of the rk3288. Smaller changes include some
IR receivers, updates of thermal settings more reflecting real-
life and testing-results.

* tag 'v4.5-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  ARM: dts: rockchip: add gpio-ir-receiver to the R89 board
  ARM: dts: rockchip: add touchscreen node to veyron minnie
  ARM: dts: rockchip: add veyron-mickey board
  ARM: dts: rockchip: add veyron-brain board
  ARM: dts: rockchip: make sure edp_24m is associated to xin24m on veyron
  ARM: dts: rockchip: override thermal settings on veyron-speedy
  ARM: dts: rockchip: update the thermal management on rk3288
  ARM: dts: rockchip: Add Crypto node for rk3288
  ARM: dts: rockchip: add rk3036-evb board
  ARM: dts: rockchip: add core rk3036 dtsi
  clk: rockchip: add dt-binding header for rk3036
  clk: rockchip: add an id for rk3288 crypto clk
  ARM: dts: rockchip: Add IR receiver to RK3288 Radxa Rock 2 Square
  ARM: dts: rockchip: add channels properties for i2s
  ARM: dts: rockchip: set system-power-controller property on rk3288-rock2
  ARM: dts: rockchip: Setup rk3066/rk3188 ethernet0 alias for u-boot
  ARM: dts: rockchip: Setup rk3288 ethernet0 alias for u-boot

UniPhier SoCs (except PH1-sLD3) have several nodes in common.
Factor out them into uniphier-common32.dtsi.  This improves the code
maintainability.

PH1-sLD3 is so old that it has more or less different register maps
than the others.  So, it cannot be included in this refactoring.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

The UART3 is assigned with IRQ 29 for old SoCs, IRQ 177 for new ones,
and PH1-Pro4 is on the boundary.

  PH1-sLD3: UART3 is unavailable
  PH1-LD4, PH1-sLD8: only IRQ 29 is supported
  PH1-Pro4: both IRQ 29 and 177 are supported
  PH1-Pro5, ProXstream2, PH1-LD6b: only IRQ 177 is supported

This SoC can choose either IRQ 29 or IRQ 177, but the former is shared
with another hardware (low speed serial0).  The latter is dedicated
for this hardware and more recommended.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'ux500-dt-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt

Merge "Device Tree changes for Ux500" from Linus Walleij:

- Push the Rohm touchscreen to the STUIB, as the TVK UIB has
  a Synaptics RMI4 touchscreen.
- Set up the right sensor IRQs for the Snowball, so that
  periodic data ready-IRQ capture starts working.
- Use wakeup-source consequently.
- Remove legacy regulator-compatible strings.
- Define the sensors on the HREFP TVK board properly.

* tag 'ux500-dt-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
  ARM: ux500: configure the sensors on the TVK board correctly
  ARM: u300: remove regulator-compatible usage
  ARM: ux500: remove regulator-compatible usage
  ARM: ux500: replace legacy *,wakeup property with wakeup-source
  ARM: ux500: Assign proper sensor IRQs for Snowball
  ARM: ux500: push down Rohm TS to STUIB

Merge tag 'renesas-dt2-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Merge "Second Round of Renesas ARM Based SoC DT Updates for v4.5" from Simon Horman:

* sh73a0, r8a7740: Add L2 cache-controller node
* r8a7791, r8a7794: remove deprecated #gpio-range-cells
* r8a7793: Add DU support and enable for VGA port
* r8a7790: switch console back to scif0
* alt: Correct ether and scif2 pinmux
* koelsch: Correct hdmi pinmux
* silk, lager, porter, bockw: Move SPI FLASH partitions to subnode
* bockw: Add schi0 pinmux

* tag 'renesas-dt2-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: sh73a0 dtsi: Add L2 cache-controller node
  ARM: shmobile: r8a7740 dtsi: Add L2 cache-controller node
  ARM: shmobile: alt: Correct ether pfc
  ARM: shmobile: alt: Correct scif2 pfc
  ARM: shmobile: silk: Move SPI FLASH partitions to subnode
  ARM: shmobile: lager: Move SPI FLASH partitions to subnode
  ARM: shmobile: porter: Move SPI FLASH partitions to subnode
  ARM: shmobile: bockw: Move SPI FLASH partition to subnode
  ARM: shmobile: r8a7791: koelsch: Fix pinmux for HDMI
  ARM: shmobile: r8a7794: remove deprecated #gpio-range-cells from dtsi
  ARM: shmobile: r8a7791: remove deprecated #gpio-range-cells from dtsi
  ARM: shmobile: r8a7793: Add DU node to device tree
  ARM: shmobile: r8a7794: alt: Enable PFC DU for the VGA port
  ARM: shmobile: bockw dts: define sdhi0 pins with pull-ups
  ARM: shmobile: r8a7790: switch console back to scif0

Merge tag 'renesas-dt-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Merge "Renesas ARM Based SoC DT Updates for v4.5" from Simon Horman:

* henninger: Remove as it is now replaced by silk
* koelsch: Move SPI partitions to subnode
* porter: Add CAN0 and HS-USB support
* r8a7793/gose: Add QSPI, PFC support
* r8a7793: Add GPIO, DMAC, theral, IPMMU support
* r8a7794/alt: Add DU support
* r8a7794: Disable all IPMMU nodes by default
* r8a779[0134]: Use Use SoC specific binding for rcar-dmac
* r8a779[01], r8a73a4, r8a7740, sh73a0: replace gpio-key, wakeup with
  wakeup-source property
* r8a779[14]: Correct "gpio-ranges" properties
* r8a779[14]: Remove bogus imp_clk node
* silk: Add SDHI1 support

* tag 'renesas-dt-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (29 commits)
  ARM: shmobile: alt: add VIN0, ADV7180 DT support
  ARM: shmobile: alt: add I2C1 DT support
  ARM: shmobile: alt: Add pfc pins to DT
  ARM: shmobile: r8a7794: Use SoC specific binding for rcar-dmac nodes
  ARM: shmobile: r8a7793: Use SoC specific binding for rcar-dmac nodes
  ARM: shmobile: r8a7791: Use SoC specific binding for rcar-dmac nodes
  ARM: shmobile: r8a7790: Use SoC specific binding for rcar-dmac nodes
  ARM: shmobile: r8a7793: Add GPIO nodes to device tree
  ARM: shmobile: r8a7794: alt: Enable VGA port
  ARM: shmobile: r8a7794: Add DU node to device tree
  ARM: shmobile: r8a7794: Add DU0 clock
  ARM: shmobile: gose: Add QSPI device to DT
  ARM: shmobile: r8a7793: Add QSPI device to DT
  ARM: shmobile: r8a7793: Add DMAC devices to DT
  ARM: shmobile: koelsch: Move SPI FLASH partitions to subnode
  ARM: shmobile: gose: Configure PFC in DT
  ARM: shmobile: r8a7793: Add PFC to DT
  ARM: shmobile: r8a7793: Add thermal device to DT
  ARM: shmobile: henninger: remove board DT
  ARM: shmobile: porter: add CAN0 DT support
  ...

Merge LPC32xx DTS changes for v4.5 from Vladimir Zapolskiy:

Main changes in the series:
- Added description of the second PWM controller device
- Added External Memory Controller device tree node (Primecell PL175)
- Added device tree nodes for standard timer controllers
- USB controllers are grouped
- Various minor clean-ups needed for further development of LPC32xx

* 'lpc32xx-dts' of https://github.com/vzapolskiy/linux:
  arm: dts: lpc32xx: move USB controller subdevices into own device node
  arm: dts: lpc32xx: add device nodes for standard timers
  arm: dts: lpc32xx: add external memory controller device node
  arm: dts: ea3250/phy3250: specify phys memory offset for lpc32xx boards
  arm: dts: lpc32xx: add device node for the second pwm controller
  arm: dts: lpc32xx: add reg property to cpu device node
  arm: dts: lpc32xx: add labels to all defined peripheral nodes
  arm: dts: lpc32xx: change include syntax to be C preprocessor friendly

Add support for the IR receiver present on the R89 board.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Minnie provides an elan,ekth3500 touchscreen over the display,
so add the necessary node to enable it.
Signed-off-by: Heiko Stuebner <heiko.stuebner@collabora.com>

Also known as the Asus Chromebit.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
For the license change:
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Similar to pinky, brain is a development model and probably also
nearing extinction. But to keep pinky from being lonely I'll keep
the two brain boards around as well, especially as they as well
have easily accessible dut-connectors.
Signed-off-by: Heiko Stuebner <heiko.stuebner@collabora.com>
For the license change:
Acked-by: Brian Norris <briannorris@chromium.org>

The edp-24m clock has two possible sources: the 24MHz oscillator as well
as an external 27MHz input. The power-on-default is the 27MHz clock which
is not supplied on all Rockchip boards. While on all current boards and
also all Veyron Chromebooks the bootloader seems to adapt the muxing to
the internal source, this doesn't seem to be the case on headless veyron
devices like brain and mickey making the edp-24m clock an orphan.
On the hardware side the 27m input also is not connected at all.

With the upcoming deferral of orphan-clocks this results in the power-
domain code deferring, as it cannot request the needed clock and if the
synchronous reset is sucessfullat all in this case is also unknown.

So fix that by making sure, the edp-24m clock is muxed to the internal
24MHz oscillator at all times.
Signed-off-by: Heiko Stuebner <heiko.stuebner@collabora.com>

The U8500 HREF TVK board actually has a large set of sensors, with
their interrupt lines connected using open drain electronics.
Configure the two accelerometers and two magnetometers so we get
all sensors to actually probe on boot.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

According to a commit on the ChromeOS kernel, the temperature of the Speedy
surface is over skin temperature spec. So adjust the thermal settings
to mimic the ChromeOS tree to stay within these spec limits.
Signed-off-by: Heiko Stuebner <heiko.stuebner@collabora.com>
Reviewed-by: Caesar Wang <wxt@rock-chips.com>

In some cases the machine radiating is very poor,sometime the temperature
is rising very quickly on heavy loading.So we need have more frequent
polling and better granularity.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@collabora.com>

Pull nouveau and radeon fixes from Dave Airlie:
 "Just some nouveau and radeon/amdgpu fixes.

  The nouveau fixes look large as the firmware context files are
  regenerated, but the actual change is quite small"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon: make some dpm errors debug only
  drm/nouveau/volt/pwm/gk104: fix an off-by-one resulting in the voltage not being set
  drm/nouveau/nvif: allow userspace access to its own client object
  drm/nouveau/gr/gf100-: fix oops when calling zbc methods
  drm/nouveau/gr/gf117-: assume no PPC if NV_PGRAPH_GPC_GPM_PD_PES_TPC_ID_MASK is zero
  drm/nouveau/gr/gf117-: read NV_PGRAPH_GPC_GPM_PD_PES_TPC_ID_MASK from correct GPC
  drm/nouveau/gr/gf100-: split out per-gpc address calculation macro
  drm/nouveau/bios: return actual size of the buffer retrieved via _ROM
  drm/nouveau/instmem: protect instobj list with a spinlock
  drm/nouveau/pci: enable c800 magic for some unknown Samsung laptop
  drm/nouveau/pci: enable c800 magic for Clevo P157SM
  drm/radeon: make rv770_set_sw_state failures non-fatal
  drm/amdgpu: move dependency handling out of atomic section v2
  drm/amdgpu: optimize scheduler fence handling
  drm/amdgpu: remove vm->mutex
  drm/amdgpu: add mutex for ba_va->valids/invalids
  drm/amdgpu: adapt vce session create interface changes
  drm/amdgpu: vce use multiple cache surface starting from stoney
  drm/amdgpu: reset vce trap interrupt flag

Pull RTC fixes from Alexandre Belloni:
 "Two fixes for the ds1307 alarm and wakeup"

* tag 'rtc-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
  rtc: ds1307: fix alarm reading at probe time
  rtc: ds1307: fix kernel splat due to wakeup irq handling

Pull MIPS fix from Ralf Baechle:
 "Just a fix for empty loops that may be removed by non-antique GCC"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Fix delay loops which may be removed by GCC.

Pull m68k fixes from Geert Uytterhoeven:
 "Summary:

   - Add missing initialization of max_pfn, which is needed to make
     selftests/vm/mlock2-tests succeed,

   - Wire up new mlock2 syscall"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k: Wire up mlock2
  m68knommu: Add missing initialization of max_pfn and {min,max}_low_pfn
  m68k/mm: sun3 - Add missing initialization of max_pfn and {min,max}_low_pfn
  m68k/mm: m54xx - Add missing initialization of max_pfn
  m68k/mm: motorola - Add missing initialization of max_pfn

Pull ARM fixes from Russell King:
 "Just two changes this time around:

   - wire up the new mlock2 syscall added during the last merge window

   - fix a build problem with certain configurations provoked by making
     CONFIG_OF user selectable"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8454/1: OF implies OF_FLATTREE
  ARM: wire up mlock2 syscall

Pull SCSI target fixes from Nicholas Bellinger:
 - fix tcm-user backend driver expired cmd time processing (agrover)
 - eliminate kref_put_spinlock_irqsave() for I/O completion (bart)
 - fix iscsi login kthread failure case hung task regression (nab)
 - fix COMPARE_AND_WRITE completion use-after-free race (nab)
 - fix COMPARE_AND_WRITE with SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC non zero
   SGL offset data corruption.  (Jan + Doug)
 - fix >= v4.4-rc1 regression for tcm_qla2xxx enable configfs attribute
   (Himanshu + HCH)

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  target/stat: print full t10_wwn.model buffer
  target: fix COMPARE_AND_WRITE non zero SGL offset data corruption
  qla2xxx: Fix regression introduced by target configFS changes
  kref: Remove kref_put_spinlock_irqsave()
  target: Invoke release_cmd() callback without holding a spinlock
  target: Fix race for SCF_COMPARE_AND_WRITE_POST checking
  iscsi-target: Fix rx_login_comp hang after login failure
  iscsi-target: return -ENOMEM instead of -1 in case of failed kmalloc()
  target/user: Do not set unused fields in tcmu_ops
  target/user: Fix time calc in expired cmd processing

Pull thermal management fixes from Zhang Rui:
 "Specifics:

 - several fixes and cleanups on Rockchip thermal drivers.

 - add the missing support of RK3368 SoCs in Rockchip driver.

 - small fixes on of-thermal, power_allocator, rcar driver, IMX, and
   QCOM drivers, and also compilation fixes, on thermal.h, when thermal
   is not selected"

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
  imx: thermal: use CPU temperature grade info for thresholds
  thermal: fix thermal_zone_bind_cooling_device prototype
  Revert "thermal: qcom_spmi: allow compile test"
  thermal: rcar_thermal: remove redundant operation
  thermal: of-thermal: Reduce log level for message when can't fine thermal zone
  thermal: power_allocator: Use temperature reading from tz
  thermal: rockchip: Support the RK3368 SoCs in thermal driver
  thermal: rockchip: consistently use int for temperatures
  thermal: rockchip: Add the sort mode for adc value increment or decrement
  thermal: rockchip: improve the conversion function
  thermal: rockchip: trivial: fix typo in commit
  thermal: rockchip: better to compatible the driver for different SoCs
  dt-bindings: rockchip-thermal: Support the RK3368 SoCs compatible

Cut 'n paste error saw it only process sizeof(t10_wwn.vendor) characters.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

target_core_sbc's compare_and_write functionality suffers from taking
data at the wrong memory location when writing a CAW request to disk
when a SGL offset is non-zero.

This can happen with loopback and vhost-scsi fabric drivers when
SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC is used to map existing user-space
SGL memory into COMPARE_AND_WRITE READ/WRITE payload buffers.

Given the following sample LIO subtopology,

% targetcli ls /loopback/
o- loopback ................................. [1 Target]
  o- naa.6001405ebb8df14a ....... [naa.60014059143ed2b3]
    o- luns ................................... [2 LUNs]
      o- lun0 ................ [iblock/ram0 (/dev/ram0)]
      o- lun1 ................ [iblock/ram1 (/dev/ram1)]
% lsscsi -g
[3:0:1:0]    disk    LIO-ORG  IBLOCK           4.0   /dev/sdc   /dev/sg3
[3:0:1:1]    disk    LIO-ORG  IBLOCK           4.0   /dev/sdd   /dev/sg4

the following bug can be observed in Linux 4.3 and 4.4~rc1:

% perl -e 'print chr$_ for 0..255,reverse 0..255' >rand
% perl -e 'print "\0" x 512' >zero
% cat rand >/dev/sdd
% sg_compare_and_write -i rand -D zero --lba 0 /dev/sdd
% sg_compare_and_write -i zero -D rand --lba 0 /dev/sdd
Miscompare reported
% hexdump -Cn 512 /dev/sdd
00000000  0f 0e 0d 0c 0b 0a 09 08  07 06 05 04 03 02 01 00
00000010  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00
*
00000200

Rather than writing all-zeroes as instructed with the -D file, it
corrupts the data in the sector by splicing some of the original
bytes in. The page of the first entry of cmd->t_data_sg includes the
CDB, and sg->offset is set to a position past the CDB. I presume that
sg->offset is also the right choice to use for subsequent sglist
members.
Signed-off-by: Jan Engelhardt <jengelh@netitwork.de>
Tested-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

this patch fixes following regression

 # targetcli
 [Errno 13] Permission denied: '/sys/kernel/config/target/qla2xxx/21:00:00:0e:1e:08:c7:20/tpgt_1/enable'

Fixes: 2eafd729 ("target: use per-attribute show and store methods")
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

The last user is gone. Hence remove this function.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

This patch fixes the following kernel warning because it avoids that
IRQs are disabled while ft_release_cmd() is invoked (fc_seq_set_resp()
invokes spin_unlock_bh()):

WARNING: CPU: 3 PID: 117 at kernel/softirq.c:150 __local_bh_enable_ip+0xaa/0x110()
Call Trace:
 [<ffffffff814f71eb>] dump_stack+0x4f/0x7b
 [<ffffffff8105e56a>] warn_slowpath_common+0x8a/0xc0
 [<ffffffff8105e65a>] warn_slowpath_null+0x1a/0x20
 [<ffffffff81062b2a>] __local_bh_enable_ip+0xaa/0x110
 [<ffffffff814ff229>] _raw_spin_unlock_bh+0x39/0x40
 [<ffffffffa03a7f94>] fc_seq_set_resp+0xe4/0x100 [libfc]
 [<ffffffffa02e604a>] ft_free_cmd+0x4a/0x90 [tcm_fc]
 [<ffffffffa02e6972>] ft_release_cmd+0x12/0x20 [tcm_fc]
 [<ffffffffa042bd66>] target_release_cmd_kref+0x56/0x90 [target_core_mod]
 [<ffffffffa042caf0>] target_put_sess_cmd+0xc0/0x110 [target_core_mod]
 [<ffffffffa042cb81>] transport_release_cmd+0x41/0x70 [target_core_mod]
 [<ffffffffa042d975>] transport_generic_free_cmd+0x35/0x420 [target_core_mod]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Joern Engel <joern@logfs.org>
Reviewed-by: Andy Grover <agrover@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

This patch addresses a race + use after free where the first
stage of COMPARE_AND_WRITE in compare_and_write_callback()
is rescheduled after the backend sends the secondary WRITE,
resulting in second stage compare_and_write_post() callback
completing in target_complete_ok_work() before the first
can return.

Because current code depends on checking se_cmd->se_cmd_flags
after return from se_cmd->transport_complete_callback(),
this results in first stage having SCF_COMPARE_AND_WRITE_POST
set, which incorrectly falls through into second stage CAW
processing code, eventually triggering a NULL pointer
dereference due to use after free.

To address this bug, pass in a new *post_ret parameter into
se_cmd->transport_complete_callback(), and depend upon this
value instead of ->se_cmd_flags to determine when to return
or fall through into ->queue_status() code for CAW.

Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

This patch addresses a case where iscsi_target_do_tx_login_io()
fails sending the last login response PDU, after the RX/TX
threads have already been started.

The case centers around iscsi_target_rx_thread() not invoking
allow_signal(SIGINT) before the send_sig(SIGINT, ...) occurs
from the failure path, resulting in RX thread hanging
indefinately on iscsi_conn->rx_login_comp.

Note this bug is a regression introduced by:

  commit e5419865
  Author: Nicholas Bellinger <nab@linux-iscsi.org>
  Date:   Wed Jul 22 23:14:19 2015 -0700

      iscsi-target: Fix iscsit_start_kthreads failure OOPs

To address this bug, complete ->rx_login_complete for good
measure in the failure path, and immediately return from
RX thread context if connection state did not actually reach
full feature phase (TARG_CONN_STATE_LOGGED_IN).

Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Smatch complains about returning hard coded error codes, silence this
warning.

drivers/target/iscsi/iscsi_target_parameters.c:211
   iscsi_create_default_params() warn: returning -1 instead of -ENOMEM is sloppy
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

TCMU sets TRANSPORT_FLAG_PASSTHROUGH, so INQUIRY commands will not be
emulated by LIO but passed up to userspace. Therefore TCMU should not
set these, just like pscsi doesn't.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

Reversed arguments meant that we were doing nothing for cmds whose deadline
had passed.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

On the ARM architecture, individual platforms select CONFIG_USE_OF if they
need it, but all device tree code is keyed off CONFIG_OF. When building
a platform without DT support and manually enabling CONFIG_OF, we now
get a number of build errors, e.g.

arch/arm/kernel/devtree.c: In function 'setup_machine_fdt':
arch/arm/kernel/devtree.c:215:19: error: implicit declaration of function 'early_init_dt_verify' [-Werror=implicit-function-declaration]

We could now try to separate the use case of booting from DT vs. the
case of using the dynamic implementation, but that seems more complicated
than it can gain us.

This simply changes the ARM Kconfig file to always enable OF_RESERVED_MEM
and OF_EARLY_FLATTREE when CONFIG_OF is enabled. These options add a little
extra code when we just want the dynamic OF implementation, but that seems
like a rather obscure case, and this version solves all CONFIG_OF related
randconfig regressions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 0166dc11 ("of: make CONFIG_OF user selectable")
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Pull PCI fixes from Bjorn Helgaas:
 "Here are a few fixes I'd like to have in v4.4: a generic one for sysfs
  and three for HiSilicon and DesignWare host controllers.

  Summary:

  NUMA:
   - Prevent out of bounds access in numa_node override (Mathias Krause)

  HiSilicon host bridge driver:
   - Fix deferred probing (Arnd Bergmann)

  Synopsys DesignWare host bridge driver:
   - Remove incorrect io_base assignment (Stanimir Varbanov)
   - Move align_resource function pointer to pci_host_bridge structure
     (Gabriele Paoloni)"

* tag 'pci-v4.4-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  ARM/PCI: Move align_resource function pointer to pci_host_bridge structure
  PCI: hisi: Fix deferred probing
  PCI: designware: Remove incorrect io_base assignment
  PCI: Prevent out of bounds access in numa_node override

Pull NFS client bugfixes from Trond Myklebust:
 "Highlights include:

  Stable patches:
   - Fix a NFSv4 callback identifier leak that was also causing client
     crashes
   - Fix NFSv4 callback decoding issues when incoming requests are
     truncated
   - Don't declare the attribute cache valid when we call
     nfs_update_inode with an empty attribute structure.
   - Resend LAYOUTGET when there is a race that changes the seqid

  Bugfixes:
   - Fix a number of issues with the NFSv4.2 CLONE ioctl()
   - Properly set NFS v4.2 NFSDBG_FACILITY
   - NFSv4 referrals are broken; Cleanup FATTR4_WORD0_FS_LOCATIONS after
     decoding success
   - Use sliding delay when LAYOUTGET gets NFS4ERR_DELAY
   - Ensure that attrcache is revalidated after a SETATTR"

* tag 'nfs-for-4.4-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  nfs4: resend LAYOUTGET when there is a race that changes the seqid
  nfs: if we have no valid attrs, then don't declare the attribute cache valid
  nfs: ensure that attrcache is revalidated after a SETATTR
  nfs4: limit callback decoding to received bytes
  nfs4: start callback_ident at idr 1
  nfs: use sliding delay when LAYOUTGET gets NFS4ERR_DELAY
  NFS4: Cleanup FATTR4_WORD0_FS_LOCATIONS after decoding success
  NFS: Properly set NFS v4.2 NFSDBG_FACILITY
  nfs: reduce the amount of ifdefs for v4.2 in nfs4file.c
  nfs: use btrfs ioctl defintions for clone
  nfs: allow intra-file CLONE
  nfs: offer native ioctls even if CONFIG_COMPAT is set
  nfs: pass on count for CLONE operations

Pull watchdog fixes from Wim Van Sebroeck:
 - a null pointer dereference fix for omap_wdt
 - some clock related fixes for pnx4008
 - an underflow fix in wdt_set_timeout() for w83977f_wdt
 - restart fix for tegra wdt
 - Kconfig change to support Freescale Layerscape platforms
 - fix for stopping the mtk_wdt watchdog

* git://www.linux-watchdog.org/linux-watchdog:
  watchdog: mtk_wdt: Use MODE_KEY when stopping the watchdog
  watchdog: Add support for Freescale Layerscape platforms
  watchdog: tegra: Stop watchdog first if restarting
  watchdog: w83977f_wdt: underflow in wdt_set_timeout()
  watchdog: pnx4008: make global wdt_clk static
  watchdog: pnx4008: fix warnings caused by enabling unprepared clock
  watchdog: omap_wdt: fix null pointer dereference

Pull btrfs fixes from Chris Mason:
 "This has Mark Fasheh's patches to fix quota accounting during subvol
  deletion, which we've been working on for a while now.  The patch is
  pretty small but it's a key fix.

  Otherwise it's a random assortment"

* 'for-linus-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: fix balance range usage filters in 4.4-rc
  btrfs: qgroup: account shared subtree during snapshot delete
  Btrfs: use btrfs_get_fs_root in resolve_indirect_ref
  btrfs: qgroup: fix quota disable during rescan
  Btrfs: fix race between cleaner kthread and space cache writeout
  Btrfs: fix scrub preventing unused block groups from being deleted
  Btrfs: fix race between scrub and block group deletion
  btrfs: fix rcu warning during device replace
  btrfs: Continue replace when set_block_ro failed
  btrfs: fix clashing number of the enhanced balance usage filter
  Btrfs: fix the number of transaction units needed to remove a block group
  Btrfs: use global reserve when deleting unused block group after ENOSPC
  Btrfs: tests: checking for NULL instead of IS_ERR()
  btrfs: fix signed overflows in btrfs_sync_file

Pull security layer fixes from James Morris:
 "A fix for SELinux policy processing (regression introduced by
  commit fa1aa143: "selinux: extended permissions for ioctls"), as
  well as a fix for the user-triggerable oops in the Keys code"

* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  KEYS: Fix handling of stored error in a negatively instantiated user key
  selinux: fix bug in conditional rules handling

Pull ARM SoC fixes from Arnd Bergmann:
 "There is a small backlog of at91 patches here, the most significant is
  the addition of some sama5d2 Xplained nodes that were waiting on an
  MFD include file to get merged through another tree.

  We normally try to sort those out before the merge window opens, but
  the maintainer wasn't aware of that here and I decided to merge the
  changes this time as an exception.

  On OMAP a series of audio changes for dra7 missed the merge window but
  turned out to be necessary to fix a boot time imprecise external abort
  error and to get audio working.

  The other changes are the usual simple changes, here is a list sorted
  by platform:

  at91:
	removal of a useless defconfig option
	removal of some legacy DT pieces
	use of the proper watchdog compatible string
	update of the MAINTAINERS entries for some Atmel drivers

  drivers/scpi:
	hide get_scpi_ops in module from built-in code

  imx:
	add missing .irq_set_type for i.MX GPC irq_chip.
	fix the wrong spi-num-chipselects settings for Vybrid DSPI devices.
	fix a merge error in Vybrid dts regarding to ADC device property

  keystone:
        fix the optional PDSP firmware loading
        fix linking RAM setup for QMs
        fix crash with clk_ignore_unused

  mediatek:
	Enable SCPSYS power domain driver by default

  mvebu:
	fix QNAP TS219 power-off in dts
	fix legacy get_irqnr_and_base for dove and orion5x

  omap:
	fix l4 related boot time errors for dm81xx
	use lockless cldm/pwrdm api in omap4_boot_secondary
	remove t410 abort handler to avoid hiding other critical errors
	mark cpuidle tracepoints as _rcuidle
	fix module alias for omap-ocp2scp

  pxa:
	palm: Fix typos in PWM lookup table code

  renesas:
	missing __initconst annotation for r8a7793_boards_compat_dt

  rockchip:
	disable mmc-tuning on the veyron-minnie board
	adding the init state for the over-temperature-protection

  zx:
	only build power domain code when CONFIG_PM=y"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
  ARM: OMAP4+: SMP: use lockless clkdm/pwrdm api in omap4_boot_secondary
  arm: omap2+: add missing HWMOD_NO_IDLEST in 81xx hwmod data
  ARM: orion5x: Fix legacy get_irqnr_and_base
  ARM: dove: Fix legacy get_irqnr_and_base
  soc: Mediatek: Enable SCPSYS power domain driver by default
  ARM: dts: vfxxx: Fix dspi[01] spi-num-chipselects.
  ARM: dts: keystone: k2l: fix kernel crash when clk_ignore_unused is not in bootargs
  soc: ti: knav_qmss_queue: Fix linking RAM setup for queue managers
  soc: ti: use request_firmware_direct() as acc firmware is optional
  ARM: imx: add platform irq type setting in gpc
  ARM: dts: vfxxx: Fix erroneous property in esdhc0 node
  ARM: shmobile: r8a7793: proper constness with __initconst
  scpi: hide get_scpi_ops in module from built-in code
  ARM: zx: only build power domain code when CONFIG_PM=y
  ARM: pxa: palm: Fix typos in PWM lookup table code
  ARM: dts: Kirkwood: Fix QNAP TS219 power-off
  ARM: dts: rockchip: Add OTP gpio pinctrl to rk3288 tsadc node
  ARM: dts: rockchip: temporarily remove emmc hs200 speed from rk3288 minnie
  MAINTAINERS: Atmel drivers: change NAND and ISI entries
  ARM: at91/dt: sama5d2 Xplained: add several devices
  ...